src/arm/samsung/exynos4412-p4note.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Samsung's Exynos4412 based p4note device family base DT.
   4  * Based on exynos4412-midas.dtsi.
   5  *
   6  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
   7  *              http://www.samsung.com
   8  */
   9
  10 /dts-v1/;
  11 #include "exynos4412.dtsi"
  12 #include "exynos4412-ppmu-common.dtsi"
  13
  14 #include <dt-bindings/clock/maxim,max77686.h>
  15 #include <dt-bindings/gpio/gpio.h>
  16 #include <dt-bindings/input/linux-event-codes.h>
  17 #include <dt-bindings/interrupt-controller/irq.h>
  18 #include <dt-bindings/power/summit,smb347-charger.h>
  19 #include "exynos-pinctrl.h"
  20
  21 / {
  22         compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4";
  23
  24         memory@40000000 {
  25                 device_type = "memory";
  26                 reg = <0x40000000 0x80000000>;
  27         };
  28
  29         aliases {
  30                 mmc0 = &mshc_0;
  31                 mmc2 = &sdhci_2;
  32                 mmc3 = &sdhci_3;
  33         };
  34
  35         chosen {
  36                 stdout-path = &serial_2;
  37         };
  38
  39         firmware@204f000 {
  40                 compatible = "samsung,secure-firmware";
  41                 reg = <0x0204f000 0x1000>;
  42         };
  43
  44         fixed-rate-clocks {
  45                 xxti {
  46                         compatible = "samsung,clock-xxti";
  47                         clock-frequency = <0>;
  48                 };
  49
  50                 xusbxti {
  51                         compatible = "samsung,clock-xusbxti";
  52                         clock-frequency = <24000000>;
  53                 };
  54         };
  55
  56         gpio-keys {
  57                 compatible = "gpio-keys";
  58                 pinctrl-names = "default";
  59                 pinctrl-0 = <&gpio_keys>;
  60
  61                 key-down {
  62                         gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
  63                         linux,code = <KEY_VOLUMEDOWN>;
  64                         label = "volume down";
  65                         debounce-interval = <10>;
  66                 };
  67
  68                 key-up {
  69                         gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
  70                         linux,code = <KEY_VOLUMEUP>;
  71                         label = "volume up";
  72                         debounce-interval = <10>;
  73                 };
  74
  75                 key-power {
  76                         gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
  77                         linux,code = <KEY_POWER>;
  78                         label = "power";
  79                         debounce-interval = <10>;
  80                         wakeup-source;
  81                 };
  82         };
  83
  84         voltage-regulator-1 {
  85                 compatible = "regulator-fixed";
  86                 regulator-name = "TSP_LDO1";
  87                 pinctrl-names = "default";
  88                 pinctrl-0 = <&tsp_reg_gpio_1>;
  89                 gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>;
  90                 enable-active-high;
  91                 regulator-always-on;
  92         };
  93
  94         voltage-regulator-2 {
  95                 compatible = "regulator-fixed";
  96                 regulator-name = "TSP_LDO2";
  97                 pinctrl-names = "default";
  98                 pinctrl-0 = <&tsp_reg_gpio_2>;
  99                 gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
 100                 enable-active-high;
 101                 regulator-always-on;
 102         };
 103
 104         voltage-regulator-3 {
 105                 compatible = "regulator-fixed";
 106                 regulator-name = "TSP_LDO3";
 107                 pinctrl-names = "default";
 108                 pinctrl-0 = <&tsp_reg_gpio_3>;
 109                 gpios = <&gpb 7 GPIO_ACTIVE_HIGH>;
 110                 startup-delay-us = <20000>;
 111                 enable-active-high;
 112                 regulator-always-on;
 113         };
 114
 115         panel_vdd: voltage-regulator-4 {
 116                 compatible = "regulator-fixed";
 117                 regulator-name = "LCD_ENABLE";
 118                 pinctrl-names = "default";
 119                 pinctrl-0 = <&lcd_enable>;
 120                 gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>;
 121                 enable-active-high;
 122                 regulator-boot-on;
 123         };
 124
 125         wlan_pwrseq: sdhci3-pwrseq {
 126                 compatible = "mmc-pwrseq-simple";
 127                 reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
 128                 pinctrl-0 = <&wifi_reset>;
 129                 pinctrl-names = "default";
 130                 clocks = <&max77686 MAX77686_CLK_PMIC>;
 131                 clock-names = "ext_clock";
 132         };
 133
 134         battery_cell: battery-cell {
 135                 compatible = "simple-battery";
 136                 device-chemistry = "lithium-ion";
 137                 constant-charge-current-max-microamp = <2200000>;
 138                 precharge-current-microamp = <250000>;
 139                 charge-term-current-microamp = <250000>;
 140                 constant-charge-voltage-max-microvolt = <4200000>;
 141         };
 142
 143         i2c-gpio-1 {
 144                 compatible = "i2c-gpio";
 145                 sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 146                 scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 147                 i2c-gpio,delay-us = <2>;
 148                 #address-cells = <1>;
 149                 #size-cells = <0>;
 150
 151                 magnetometer@c {
 152                         compatible = "asahi-kasei,ak8975";
 153                         reg = <0x0c>;
 154                         pinctrl-0 = <&ak8975_irq>;
 155                         pinctrl-names = "default";
 156                         interrupt-parent = <&gpm4>;
 157                         interrupts = <7 IRQ_TYPE_EDGE_RISING>;
 158                 };
 159         };
 160
 161         i2c-gpio-2 {
 162                 compatible = "i2c-gpio";
 163                 sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 164                 scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 165                 i2c-gpio,delay-us = <2>;
 166                 #address-cells = <1>;
 167                 #size-cells = <0>;
 168
 169                 fuel-gauge@36 {
 170                         compatible = "maxim,max17042";
 171                         reg = <0x36>;
 172                         pinctrl-0 = <&fuel_alert_irq>;
 173                         pinctrl-names = "default";
 174                         interrupt-parent = <&gpx2>;
 175                         interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 176                         maxim,rsns-microohm = <10000>;
 177                         maxim,over-heat-temp = <600>;
 178                         maxim,over-volt = <4300>;
 179                 };
 180         };
 181
 182         i2c-gpio-3 {
 183                 compatible = "i2c-gpio";
 184                 sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 185                 scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 186                 i2c-gpio,delay-us = <5>;
 187                 #address-cells = <1>;
 188                 #size-cells = <0>;
 189
 190                 adc@41 {
 191                         compatible = "st,stmpe811";
 192                         reg = <0x41>;
 193                         pinctrl-0 = <&stmpe_adc_irq>;
 194                         pinctrl-names = "default";
 195                         interrupt-parent = <&gpx0>;
 196                         interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 197                         st,adc-freq = <3>;
 198                         st,mod-12b = <1>;
 199                         st,ref-sel = <0>;
 200                         st,sample-time = <3>;
 201
 202                         adc {
 203                                 compatible = "st,stmpe-adc";
 204                                 #io-channel-cells = <1>;
 205                                 st,norequest-mask = <0x2f>;
 206                         };
 207                 };
 208         };
 209
 210         i2c-gpio-4 {
 211                 compatible = "i2c-gpio";
 212                 sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 213                 scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 214
 215                 i2c-gpio,delay-us = <2>;
 216                 #address-cells = <1>;
 217                 #size-cells = <0>;
 218
 219                 power_supply: charger@6 {
 220                         compatible = "summit,smb347";
 221                         reg = <0x6>;
 222                         summit,enable-usb-charging;
 223                         summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
 224                         summit,fast-voltage-threshold-microvolt = <2600000>;
 225                         summit,chip-temperature-threshold-celsius = <130>;
 226                         summit,usb-current-limit-microamp = <1800000>;
 227
 228                         monitored-battery = <&battery_cell>;
 229                 };
 230         };
 231
 232         panel {
 233                 compatible = "samsung,ltl101al01";
 234                 pinctrl-0 = <&lvds_nshdn>;
 235                 pinctrl-names = "default";
 236                 power-supply = <&panel_vdd>;
 237                 enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>;
 238                 backlight = <&backlight>;
 239
 240                 port {
 241                         lcd_ep: endpoint {
 242                                 remote-endpoint = <&fimd_ep>;
 243                         };
 244                 };
 245         };
 246
 247         backlight: backlight {
 248                 compatible = "pwm-backlight";
 249                 pinctrl-0 = <&led_bl_reset>;
 250                 pinctrl-names = "default";
 251                 enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>;
 252                 power-supply = <&panel_vdd>;
 253                 pwms = <&pwm 1 78770 0>;
 254                 brightness-levels = <0 48 128 255>;
 255                 num-interpolated-steps = <8>;
 256                 default-brightness-level = <12>;
 257         };
 258 };
 259
 260 &adc {
 261         vdd-supply = <&ldo3_reg>;
 262         /* not verified */
 263         status = "okay";
 264 };
 265
 266 &bus_dmc {
 267         devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
 268         vdd-supply = <&buck1_reg>;
 269         status = "okay";
 270 };
 271
 272 &bus_acp {
 273         devfreq = <&bus_dmc>;
 274         status = "okay";
 275 };
 276
 277 &bus_c2c {
 278         devfreq = <&bus_dmc>;
 279         status = "okay";
 280 };
 281
 282 &bus_leftbus {
 283         devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
 284         vdd-supply = <&buck3_reg>;
 285         status = "okay";
 286 };
 287
 288 &bus_rightbus {
 289         devfreq = <&bus_leftbus>;
 290         status = "okay";
 291 };
 292
 293 &bus_display {
 294         devfreq = <&bus_leftbus>;
 295         status = "okay";
 296 };
 297
 298 &bus_fsys {
 299         devfreq = <&bus_leftbus>;
 300         status = "okay";
 301 };
 302
 303 &bus_peri {
 304         devfreq = <&bus_leftbus>;
 305         status = "okay";
 306 };
 307
 308 &bus_mfc {
 309         devfreq = <&bus_leftbus>;
 310         status = "okay";
 311 };
 312
 313 &cpu0 {
 314         cpu0-supply = <&buck2_reg>;
 315 };
 316
 317 &cpu_thermal {
 318         cooling-maps {
 319                 map0 {
 320                         /* Corresponds to 800MHz at freq_table */
 321                         cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
 322                                          <&cpu2 7 7>, <&cpu3 7 7>;
 323                 };
 324                 map1 {
 325                         /* Corresponds to 200MHz at freq_table */
 326                         cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
 327                                          <&cpu2 13 13>, <&cpu3 13 13>;
 328                 };
 329         };
 330 };
 331
 332 &exynos_usbphy {
 333         status = "okay";
 334 };
 335
 336 &fimd {
 337         pinctrl-0 = <&lcd_clk &lcd_data24>;
 338         pinctrl-names = "default";
 339         #address-cells = <1>;
 340         #size-cells = <0>;
 341         status = "okay";
 342
 343         samsung,invert-vclk;
 344
 345         port@3 {
 346                 reg = <3>;
 347
 348                 fimd_ep: endpoint {
 349                         remote-endpoint = <&lcd_ep>;
 350                 };
 351         };
 352 };
 353
 354 &gpu {
 355         mali-supply = <&buck4_reg>;
 356         status = "okay";
 357 };
 358
 359 &hsotg {
 360         vusb_a-supply = <&ldo12_reg>;
 361         dr_mode = "peripheral";
 362         status = "okay";
 363 };
 364
 365 &i2c_3 {
 366         samsung,i2c-sda-delay = <100>;
 367         samsung,i2c-slave-addr = <0x10>;
 368         samsung,i2c-max-bus-freq = <400000>;
 369         pinctrl-0 = <&i2c3_bus>;
 370         pinctrl-names = "default";
 371         status = "okay";
 372
 373         touchscreen@4a {
 374                 compatible = "atmel,maxtouch";
 375                 reg = <0x4a>;
 376                 pinctrl-0 = <&tsp_rst &tsp_irq>;
 377                 pinctrl-names = "default";
 378                 interrupt-parent = <&gpm2>;
 379                 interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 380                 reset-gpios = <&gpm0 4 GPIO_ACTIVE_LOW>;
 381         };
 382 };
 383
 384 &i2c_7 {
 385         samsung,i2c-sda-delay = <100>;
 386         samsung,i2c-slave-addr = <0x10>;
 387         samsung,i2c-max-bus-freq = <400000>;
 388         pinctrl-0 = <&i2c7_bus>;
 389         pinctrl-names = "default";
 390         status = "okay";
 391
 392         max77686: pmic@9 {
 393                 compatible = "maxim,max77686";
 394                 interrupt-parent = <&gpx0>;
 395                 interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 396                 pinctrl-0 = <&max77686_irq>;
 397                 pinctrl-names = "default";
 398                 wakeup-source;
 399                 reg = <0x09>;
 400                 #clock-cells = <1>;
 401
 402                 voltage-regulators {
 403                         ldo1_reg: LDO1 {
 404                                 regulator-name = "ldo1";
 405                                 regulator-always-on;
 406                         };
 407
 408                         ldo2_reg: LDO2 {
 409                                 regulator-name = "ldo2";
 410                                 regulator-always-on;
 411                         };
 412
 413                         /* WM8994 audio */
 414                         ldo3_reg: LDO3 {
 415                                 regulator-name = "VCC_1.8V_AP";
 416                                 regulator-min-microvolt = <1800000>;
 417                                 regulator-max-microvolt = <1800000>;
 418                                 regulator-always-on;
 419                                 regulator-boot-on;
 420
 421                                 regulator-state-mem {
 422                                         regulator-on-in-suspend;
 423                                 };
 424                         };
 425
 426                         ldo4_reg: LDO4 {
 427                                 regulator-name = "ldo4";
 428                                 regulator-always-on;
 429                         };
 430
 431                         ldo5_reg: LDO5 {
 432                                 regulator-name = "VCC_1.8V_IO";
 433                                 regulator-min-microvolt = <1800000>;
 434                                 regulator-max-microvolt = <1800000>;
 435
 436                                 regulator-state-mem {
 437                                         regulator-off-in-suspend;
 438                                 };
 439                         };
 440
 441                         ldo6_reg: LDO6 {
 442                                 regulator-name = "ldo6";
 443                                 regulator-always-on;
 444                         };
 445
 446                         ldo7_reg: LDO7 {
 447                                 regulator-name = "ldo7";
 448                                 regulator-always-on;
 449                         };
 450
 451                         /* CSI IP block */
 452                         ldo8_reg: LDO8 {
 453                                 regulator-name = "VMIPI_1.0V";
 454                                 regulator-min-microvolt = <1000000>;
 455                                 regulator-max-microvolt = <1000000>;
 456                                 regulator-always-on;
 457                                 regulator-boot-on;
 458
 459                                 regulator-state-mem {
 460                                         regulator-on-in-suspend;
 461                                 };
 462                         };
 463
 464                         /* IR LED on/off */
 465                         ldo9_reg: LDO9 {
 466                                 regulator-name = "VLED_IC_1.9V";
 467                                 regulator-min-microvolt = <1950000>;
 468                                 regulator-max-microvolt = <1950000>;
 469
 470                                 regulator-state-mem {
 471                                         regulator-off-in-suspend;
 472                                 };
 473                         };
 474
 475                         /* CSI IP block */
 476                         ldo10_reg: LDO10 {
 477                                 regulator-name = "VMIPI_1.8V";
 478                                 regulator-min-microvolt = <1800000>;
 479                                 regulator-max-microvolt = <1800000>;
 480                                 regulator-always-on;
 481                                 regulator-boot-on;
 482
 483                                 regulator-state-mem {
 484                                         regulator-on-in-suspend;
 485                                 };
 486                         };
 487
 488                         ldo11_reg: LDO11 {
 489                                 regulator-name = "VABB1_1.9V";
 490                                 regulator-min-microvolt = <1950000>;
 491                                 regulator-max-microvolt = <1950000>;
 492                                 regulator-always-on;
 493                                 regulator-boot-on;
 494
 495                                 regulator-state-mem {
 496                                         regulator-off-in-suspend;
 497                                 };
 498                         };
 499
 500                         /* USB OTG */
 501                         ldo12_reg: LDO12 {
 502                                 regulator-name = "VUOTG_3.0V";
 503                                 regulator-min-microvolt = <3000000>;
 504                                 regulator-max-microvolt = <3000000>;
 505                                 regulator-always-on;
 506                                 regulator-boot-on;
 507
 508                                 regulator-state-mem {
 509                                         regulator-on-in-suspend;
 510                                 };
 511                         };
 512
 513                         /* not connected */
 514                         ldo13_reg: LDO13 {
 515                                 regulator-name = "ldo13";
 516                         };
 517
 518                         ldo14_reg: LDO14 {
 519                                 regulator-name = "VABB2_1.9V";
 520                                 regulator-min-microvolt = <1950000>;
 521                                 regulator-max-microvolt = <1950000>;
 522                                 regulator-always-on;
 523                                 regulator-boot-on;
 524
 525                                 regulator-state-mem {
 526                                         regulator-off-in-suspend;
 527                                 };
 528                         };
 529
 530                         ldo15_reg: LDO15 {
 531                                 regulator-name = "ldo15";
 532                                 regulator-always-on;
 533                         };
 534
 535                         ldo16_reg: LDO16 {
 536                                 regulator-name = "ldo16";
 537                                 regulator-always-on;
 538                         };
 539
 540                         /* not connected */
 541                         ldo17_reg: LDO17 {
 542                                 regulator-name = "ldo17";
 543                         };
 544
 545                         /* Camera ISX012 */
 546                         ldo18_reg: LDO18 {
 547                                 regulator-name = "CAM_IO_1.8V";
 548                                 regulator-min-microvolt = <1800000>;
 549                                 regulator-max-microvolt = <1800000>;
 550
 551                                 regulator-state-mem {
 552                                         regulator-off-in-suspend;
 553                                 };
 554                         };
 555
 556                         /* Camera S5K6A3 */
 557                         ldo19_reg: LDO19 {
 558                                 regulator-name = "VT_CORE_1.8V";
 559                                 regulator-min-microvolt = <1800000>;
 560                                 regulator-max-microvolt = <1800000>;
 561
 562                                 regulator-state-mem {
 563                                         regulator-off-in-suspend;
 564                                 };
 565                         };
 566
 567                         /* not connected */
 568                         ldo20_reg: LDO20 {
 569                                 regulator-name = "ldo20";
 570                         };
 571
 572                         /* MMC2 */
 573                         ldo21_reg: LDO21 {
 574                                 regulator-name = "VTF_2.8V";
 575                                 regulator-min-microvolt = <2800000>;
 576                                 regulator-max-microvolt = <2800000>;
 577                                 maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
 578                         };
 579
 580                         /* not connected */
 581                         ldo22_reg: LDO22 {
 582                                 regulator-name = "ldo22";
 583                         };
 584
 585                         /* ADC */
 586                         ldo23_reg: LDO23 {
 587                                 regulator-name = "VDD_ADC_3.3V";
 588                                 regulator-min-microvolt = <3300000>;
 589                                 regulator-max-microvolt = <3300000>;
 590                                 regulator-always-on;
 591                                 regulator-boot-on;
 592
 593                                 regulator-state-mem {
 594                                         regulator-off-in-suspend;
 595                                 };
 596                         };
 597
 598                         /* Camera S5K6A3 */
 599                         ldo24_reg: LDO24 {
 600                                 regulator-name = "CAM_A2.8V";
 601                                 regulator-min-microvolt = <2800000>;
 602                                 regulator-max-microvolt = <2800000>;
 603
 604                                 regulator-state-mem {
 605                                         regulator-off-in-suspend;
 606                                 };
 607                         };
 608
 609                         ldo25_reg: LDO25 {
 610                                 regulator-name = "VLED_3.3V";
 611                                 regulator-min-microvolt = <3300000>;
 612                                 regulator-max-microvolt = <3300000>;
 613
 614                                 regulator-state-mem {
 615                                         regulator-off-in-suspend;
 616                                 };
 617                         };
 618
 619                         /* Camera ISX012 */
 620                         ldo26_reg: LDO26 {
 621                                 regulator-name = "3MP_AF_2.8V";
 622                                 regulator-min-microvolt = <2800000>;
 623                                 regulator-max-microvolt = <2800000>;
 624
 625                                 regulator-state-mem {
 626                                         regulator-off-in-suspend;
 627                                 };
 628                         };
 629
 630                         buck1_reg: BUCK1 {
 631                                 regulator-name = "VDD_MIF";
 632                                 regulator-min-microvolt = <850000>;
 633                                 regulator-max-microvolt = <1050000>;
 634                                 regulator-always-on;
 635                                 regulator-boot-on;
 636                         };
 637
 638                         buck2_reg: BUCK2 {
 639                                 regulator-name = "VDD_ARM";
 640                                 regulator-min-microvolt = <850000>;
 641                                 regulator-max-microvolt = <1500000>;
 642                                 regulator-always-on;
 643                                 regulator-boot-on;
 644                         };
 645
 646                         buck3_reg: BUCK3 {
 647                                 regulator-name = "VDD_INT";
 648                                 regulator-min-microvolt = <850000>;
 649                                 regulator-max-microvolt = <1100000>;
 650                                 regulator-always-on;
 651                                 regulator-boot-on;
 652                         };
 653
 654                         buck4_reg: BUCK4 {
 655                                 regulator-name = "VDD_G3D";
 656                                 regulator-min-microvolt = <850000>;
 657                                 regulator-max-microvolt = <1075000>;
 658                                 regulator-boot-on;
 659                         };
 660
 661                         buck5_reg: BUCK5 {
 662                                 regulator-name = "buck5";
 663                                 regulator-always-on;
 664                         };
 665
 666                         buck6_reg: BUCK6 {
 667                                 regulator-name = "buck6";
 668                                 regulator-always-on;
 669                         };
 670
 671                         buck7_reg: BUCK7 {
 672                                 regulator-name = "buck7";
 673                                 regulator-always-on;
 674                         };
 675
 676                         /* not connected */
 677                         buck8_reg: BUCK8 {
 678                                 regulator-name = "buck8";
 679                         };
 680
 681                         buck9_reg: BUCK9 {
 682                                 regulator-name = "3MP_CORE_1.2V";
 683                                 regulator-min-microvolt = <1200000>;
 684                                 regulator-max-microvolt = <1200000>;
 685
 686                                 regulator-state-mem {
 687                                         regulator-off-in-suspend;
 688                                 };
 689                         };
 690                 };
 691         };
 692 };
 693
 694 &mshc_0 {
 695         broken-cd;
 696         non-removable;
 697         card-detect-delay = <200>;
 698         clock-frequency = <400000000>;
 699         samsung,dw-mshc-ciu-div = <0>;
 700         samsung,dw-mshc-sdr-timing = <2 3>;
 701         samsung,dw-mshc-ddr-timing = <1 2>;
 702         mmc-ddr-1_8v;
 703         pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 704         pinctrl-names = "default";
 705         bus-width = <4>;
 706         cap-mmc-highspeed;
 707         cap-sd-highspeed;
 708         status = "okay";
 709 };
 710
 711 &pinctrl_0 {
 712         pinctrl-names = "default";
 713         pinctrl-0 = <&sleep0>;
 714
 715         tsp_reg_gpio_2: tsp-reg-gpio-2-pins {
 716                 samsung,pins = "gpb-5";
 717                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 718                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 719         };
 720
 721         tsp_reg_gpio_3: tsp-reg-gpio-3-pins {
 722                 samsung,pins = "gpb-7";
 723                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 724                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 725         };
 726
 727         lcd_enable: lcd-enable-pins {
 728                 samsung,pins = "gpc0-1";
 729                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 730                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 731         };
 732
 733         sleep0: sleep-state {
 734                 PIN_SLP(gpa0-0, INPUT, NONE);
 735                 PIN_SLP(gpa0-1, OUT0, NONE);
 736                 PIN_SLP(gpa0-2, INPUT, NONE);
 737                 PIN_SLP(gpa0-3, INPUT, UP);
 738                 PIN_SLP(gpa0-4, INPUT, NONE);
 739                 PIN_SLP(gpa0-5, INPUT, DOWN);
 740                 PIN_SLP(gpa0-6, INPUT, DOWN);
 741                 PIN_SLP(gpa0-7, INPUT, UP);
 742
 743                 PIN_SLP(gpa1-0, INPUT, DOWN);
 744                 PIN_SLP(gpa1-1, INPUT, DOWN);
 745                 PIN_SLP(gpa1-2, INPUT, DOWN);
 746                 PIN_SLP(gpa1-3, INPUT, DOWN);
 747                 PIN_SLP(gpa1-4, INPUT, DOWN);
 748                 PIN_SLP(gpa1-5, INPUT, DOWN);
 749
 750                 PIN_SLP(gpb-0, INPUT, NONE);
 751                 PIN_SLP(gpb-1, INPUT, NONE);
 752                 PIN_SLP(gpb-2, INPUT, NONE);
 753                 PIN_SLP(gpb-3, INPUT, NONE);
 754                 PIN_SLP(gpb-4, INPUT, DOWN);
 755                 PIN_SLP(gpb-5, INPUT, DOWN);
 756                 PIN_SLP(gpb-6, INPUT, DOWN);
 757                 PIN_SLP(gpb-7, INPUT, DOWN);
 758
 759                 PIN_SLP(gpc0-0, INPUT, DOWN);
 760                 PIN_SLP(gpc0-1, INPUT, DOWN);
 761                 PIN_SLP(gpc0-2, INPUT, DOWN);
 762                 PIN_SLP(gpc0-3, INPUT, DOWN);
 763                 PIN_SLP(gpc0-4, INPUT, DOWN);
 764
 765                 PIN_SLP(gpc1-0, INPUT, UP);
 766                 PIN_SLP(gpc1-1, PREV, NONE);
 767                 PIN_SLP(gpc1-2, INPUT, UP);
 768                 PIN_SLP(gpc1-3, INPUT, UP);
 769                 PIN_SLP(gpc1-4, INPUT, UP);
 770
 771                 PIN_SLP(gpd0-0, INPUT, DOWN);
 772                 PIN_SLP(gpd0-1, OUT0, NONE);
 773                 PIN_SLP(gpd0-2, INPUT, NONE);
 774                 PIN_SLP(gpd0-3, INPUT, NONE);
 775
 776                 PIN_SLP(gpd1-0, INPUT, DOWN);
 777                 PIN_SLP(gpd1-1, INPUT, DOWN);
 778                 PIN_SLP(gpd1-2, INPUT, NONE);
 779                 PIN_SLP(gpd1-3, INPUT, NONE);
 780
 781                 PIN_SLP(gpf0-0, OUT0, NONE);
 782                 PIN_SLP(gpf0-1, OUT0, NONE);
 783                 PIN_SLP(gpf0-2, OUT0, NONE);
 784                 PIN_SLP(gpf0-3, OUT0, NONE);
 785                 PIN_SLP(gpf0-4, OUT0, NONE);
 786                 PIN_SLP(gpf0-5, OUT0, NONE);
 787                 PIN_SLP(gpf0-6, OUT0, NONE);
 788                 PIN_SLP(gpf0-7, OUT0, NONE);
 789
 790                 PIN_SLP(gpf1-0, OUT0, NONE);
 791                 PIN_SLP(gpf1-1, OUT0, NONE);
 792                 PIN_SLP(gpf1-2, OUT0, NONE);
 793                 PIN_SLP(gpf1-3, OUT0, NONE);
 794                 PIN_SLP(gpf1-4, OUT0, NONE);
 795                 PIN_SLP(gpf1-5, OUT0, NONE);
 796                 PIN_SLP(gpf1-6, OUT0, NONE);
 797                 PIN_SLP(gpf1-7, OUT0, NONE);
 798
 799                 PIN_SLP(gpf2-0, OUT0, NONE);
 800                 PIN_SLP(gpf2-1, OUT0, NONE);
 801                 PIN_SLP(gpf2-2, OUT0, NONE);
 802                 PIN_SLP(gpf2-3, OUT0, NONE);
 803                 PIN_SLP(gpf2-4, OUT0, NONE);
 804                 PIN_SLP(gpf2-5, OUT0, NONE);
 805                 PIN_SLP(gpf2-6, OUT0, NONE);
 806                 PIN_SLP(gpf2-7, OUT0, NONE);
 807
 808                 PIN_SLP(gpf3-0, OUT0, NONE);
 809                 PIN_SLP(gpf3-1, OUT0, NONE);
 810                 PIN_SLP(gpf3-2, OUT0, NONE);
 811                 PIN_SLP(gpf3-3, OUT0, NONE);
 812                 PIN_SLP(gpf3-4, OUT0, NONE);
 813                 PIN_SLP(gpf3-5, OUT0, NONE);
 814
 815                 PIN_SLP(gpj0-0, INPUT, DOWN);
 816                 PIN_SLP(gpj0-1, INPUT, DOWN);
 817                 PIN_SLP(gpj0-2, INPUT, DOWN);
 818                 PIN_SLP(gpj0-3, PREV, NONE);
 819                 PIN_SLP(gpj0-4, PREV, NONE);
 820                 PIN_SLP(gpj0-5, OUT0, NONE);
 821                 PIN_SLP(gpj0-6, OUT0, NONE);
 822                 PIN_SLP(gpj0-7, OUT0, NONE);
 823
 824                 PIN_SLP(gpj1-0, OUT0, NONE);
 825                 PIN_SLP(gpj1-1, INPUT, DOWN);
 826                 PIN_SLP(gpj1-2, PREV, NONE);
 827                 PIN_SLP(gpj1-3, OUT0, NONE);
 828         };
 829 };
 830
 831 &pinctrl_1 {
 832         pinctrl-names = "default";
 833         pinctrl-0 = <&sleep1>;
 834
 835         sd3_wifi: sd3-wifi-pins {
 836                 samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 837                 samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 838                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 839         };
 840
 841         bt_shutdown: bt-shutdown-pins {
 842                 samsung,pins = "gpl0-6";
 843                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 844                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 845         };
 846
 847         uart_sel: uart-sel-pins {
 848                 samsung,pins = "gpl2-7";
 849                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 850                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 851                 samsung,pin-val = <1>;
 852                 /* 0 = CP, 1 = AP (serial output) */
 853         };
 854
 855         led_bl_reset: led-bl-reset-pins {
 856                 samsung,pins = "gpm0-1";
 857                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 858                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 859         };
 860
 861         tsp_rst: tsp-rst-pins {
 862                 samsung,pins = "gpm0-4";
 863                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 864                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 865         };
 866
 867         lvds_nshdn: lvds-nshdn-pins {
 868                 samsung,pins = "gpm0-5";
 869                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 870                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 871         };
 872
 873         tsp_irq: tsp-irq-pins {
 874                 samsung,pins = "gpm2-3";
 875                 samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 876                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 877         };
 878
 879         wifi_reset: wifi-reset-pins {
 880                 samsung,pins = "gpm3-5";
 881                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 882                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 883         };
 884
 885         tsp_reg_gpio_1: tsp-reg-gpio-1-pins {
 886                 samsung,pins = "gpm4-5";
 887                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 888                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 889         };
 890
 891         ak8975_irq: ak8975-irq-pins {
 892                 samsung,pins = "gpm4-7";
 893                 samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 894                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 895         };
 896
 897         stmpe_adc_irq: stmpe-adc-irq-pins {
 898                 samsung,pins = "gpx0-1";
 899                 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 900                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 901         };
 902
 903         max77686_irq: max77686-irq-pins {
 904                 samsung,pins = "gpx0-7";
 905                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 906         };
 907
 908         gpio_keys: gpio-keys-pins {
 909                 samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3";
 910                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 911         };
 912
 913         fuel_alert_irq: fuel-alert-irq-pins {
 914                 samsung,pins = "gpx2-3";
 915                 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 916                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 917         };
 918
 919         wifi_host_wake: wifi-host-wake-pins {
 920                 samsung,pins = "gpx2-5";
 921                 samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 922                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 923         };
 924
 925         bt_host_wakeup: bt-host-wakeup-pins {
 926                 samsung,pins = "gpx2-6";
 927                 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 928                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 929         };
 930
 931         bt_device_wakeup: bt-device-wakeup-pins {
 932                 samsung,pins = "gpx3-1";
 933                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 934                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 935         };
 936
 937         sdhci2_cd: sdhci2-cd-pins {
 938                 samsung,pins = "gpx3-4";
 939                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 940         };
 941
 942         sleep1: sleep-state {
 943                 PIN_SLP(gpk0-0, PREV, NONE);
 944                 PIN_SLP(gpk0-1, PREV, NONE);
 945                 PIN_SLP(gpk0-2, PREV, NONE);
 946                 PIN_SLP(gpk0-3, PREV, NONE);
 947                 PIN_SLP(gpk0-4, PREV, NONE);
 948                 PIN_SLP(gpk0-5, PREV, NONE);
 949                 PIN_SLP(gpk0-6, PREV, NONE);
 950
 951                 PIN_SLP(gpk1-0, INPUT, DOWN);
 952                 PIN_SLP(gpk1-1, INPUT, DOWN);
 953                 PIN_SLP(gpk1-2, INPUT, DOWN);
 954                 PIN_SLP(gpk1-3, PREV, NONE);
 955                 PIN_SLP(gpk1-4, PREV, NONE);
 956                 PIN_SLP(gpk1-5, PREV, NONE);
 957                 PIN_SLP(gpk1-6, PREV, NONE);
 958
 959                 PIN_SLP(gpk2-0, INPUT, DOWN);
 960                 PIN_SLP(gpk2-1, INPUT, DOWN);
 961                 PIN_SLP(gpk2-2, INPUT, DOWN);
 962                 PIN_SLP(gpk2-3, INPUT, DOWN);
 963                 PIN_SLP(gpk2-4, INPUT, DOWN);
 964                 PIN_SLP(gpk2-5, INPUT, DOWN);
 965                 PIN_SLP(gpk2-6, INPUT, DOWN);
 966
 967                 PIN_SLP(gpk3-0, OUT0, NONE);
 968                 PIN_SLP(gpk3-1, INPUT, NONE);
 969                 PIN_SLP(gpk3-2, INPUT, DOWN);
 970                 PIN_SLP(gpk3-3, INPUT, NONE);
 971                 PIN_SLP(gpk3-4, INPUT, NONE);
 972                 PIN_SLP(gpk3-5, INPUT, NONE);
 973                 PIN_SLP(gpk3-6, INPUT, NONE);
 974
 975                 PIN_SLP(gpl0-0, OUT0, NONE);
 976                 PIN_SLP(gpl0-1, INPUT, NONE);
 977                 PIN_SLP(gpl0-2, INPUT, NONE);
 978                 PIN_SLP(gpl0-3, INPUT, DOWN);
 979                 PIN_SLP(gpl0-4, PREV, NONE);
 980                 PIN_SLP(gpl0-6, PREV, NONE);
 981
 982                 PIN_SLP(gpl1-0, OUT0, NONE);
 983                 PIN_SLP(gpl1-1, OUT0, NONE);
 984
 985                 PIN_SLP(gpl2-0, INPUT, DOWN);
 986                 PIN_SLP(gpl2-1, INPUT, DOWN);
 987                 PIN_SLP(gpl2-2, INPUT, DOWN);
 988                 PIN_SLP(gpl2-3, INPUT, DOWN);
 989                 PIN_SLP(gpl2-4, OUT0, NONE);
 990                 PIN_SLP(gpl2-5, INPUT, DOWN);
 991                 PIN_SLP(gpl2-6, PREV, NONE);
 992                 PIN_SLP(gpl2-7, PREV, NONE);
 993
 994                 PIN_SLP(gpm0-0, PREV, NONE);
 995                 PIN_SLP(gpm0-1, OUT0, NONE);
 996                 PIN_SLP(gpm0-2, INPUT, DOWN);
 997                 PIN_SLP(gpm0-3, INPUT, NONE);
 998                 PIN_SLP(gpm0-4, OUT0, NONE);
 999                 PIN_SLP(gpm0-5, OUT0, NONE);
1000                 PIN_SLP(gpm0-6, INPUT, DOWN);
1001                 PIN_SLP(gpm0-7, OUT0, NONE);
1002
1003                 PIN_SLP(gpm1-0, INPUT, NONE);
1004                 PIN_SLP(gpm1-1, INPUT, NONE);
1005                 PIN_SLP(gpm1-2, INPUT, NONE);
1006                 PIN_SLP(gpm1-3, INPUT, NONE);
1007                 PIN_SLP(gpm1-4, INPUT, NONE);
1008                 PIN_SLP(gpm1-5, INPUT, NONE);
1009                 PIN_SLP(gpm1-6, INPUT, DOWN);
1010
1011                 PIN_SLP(gpm2-0, INPUT, NONE);
1012                 PIN_SLP(gpm2-1, INPUT, NONE);
1013                 PIN_SLP(gpm2-2, OUT0, NONE);
1014                 PIN_SLP(gpm2-3, OUT0, DOWN);
1015                 PIN_SLP(gpm2-4, INPUT, DOWN);
1016
1017                 PIN_SLP(gpm3-0, PREV, NONE);
1018                 PIN_SLP(gpm3-1, PREV, NONE);
1019                 PIN_SLP(gpm3-2, PREV, NONE);
1020                 PIN_SLP(gpm3-3, OUT1, NONE);
1021                 PIN_SLP(gpm3-4, OUT0, DOWN);
1022                 PIN_SLP(gpm3-5, PREV, NONE);
1023                 PIN_SLP(gpm3-6, PREV, NONE);
1024                 PIN_SLP(gpm3-7, OUT0, NONE);
1025
1026                 PIN_SLP(gpm4-0, INPUT, NONE);
1027                 PIN_SLP(gpm4-1, INPUT, NONE);
1028                 PIN_SLP(gpm4-2, INPUT, DOWN);
1029                 PIN_SLP(gpm4-3, INPUT, DOWN);
1030                 PIN_SLP(gpm4-4, PREV, NONE);
1031                 PIN_SLP(gpm4-5, OUT0, NONE);
1032                 PIN_SLP(gpm4-6, OUT0, NONE);
1033                 PIN_SLP(gpm4-7, INPUT, DOWN);
1034
1035                 PIN_SLP(gpy0-0, INPUT, DOWN);
1036                 PIN_SLP(gpy0-1, INPUT, DOWN);
1037                 PIN_SLP(gpy0-2, INPUT, NONE);
1038                 PIN_SLP(gpy0-3, INPUT, NONE);
1039                 PIN_SLP(gpy0-4, INPUT, NONE);
1040                 PIN_SLP(gpy0-5, INPUT, NONE);
1041
1042                 PIN_SLP(gpy1-0, INPUT, DOWN);
1043                 PIN_SLP(gpy1-1, INPUT, DOWN);
1044                 PIN_SLP(gpy1-2, INPUT, DOWN);
1045                 PIN_SLP(gpy1-3, INPUT, DOWN);
1046
1047                 PIN_SLP(gpy2-0, PREV, NONE);
1048                 PIN_SLP(gpy2-1, INPUT, DOWN);
1049                 PIN_SLP(gpy2-2, INPUT, NONE);
1050                 PIN_SLP(gpy2-3, INPUT, NONE);
1051                 PIN_SLP(gpy2-4, INPUT, NONE);
1052                 PIN_SLP(gpy2-5, INPUT, NONE);
1053
1054                 PIN_SLP(gpy3-0, INPUT, DOWN);
1055                 PIN_SLP(gpy3-1, INPUT, DOWN);
1056                 PIN_SLP(gpy3-2, INPUT, DOWN);
1057                 PIN_SLP(gpy3-3, INPUT, DOWN);
1058                 PIN_SLP(gpy3-4, INPUT, DOWN);
1059                 PIN_SLP(gpy3-5, INPUT, DOWN);
1060                 PIN_SLP(gpy3-6, INPUT, DOWN);
1061                 PIN_SLP(gpy3-7, INPUT, DOWN);
1062
1063                 PIN_SLP(gpy4-0, INPUT, DOWN);
1064                 PIN_SLP(gpy4-1, INPUT, DOWN);
1065                 PIN_SLP(gpy4-2, INPUT, DOWN);
1066                 PIN_SLP(gpy4-3, INPUT, DOWN);
1067                 PIN_SLP(gpy4-4, INPUT, DOWN);
1068                 PIN_SLP(gpy4-5, INPUT, DOWN);
1069                 PIN_SLP(gpy4-6, INPUT, DOWN);
1070                 PIN_SLP(gpy4-7, INPUT, DOWN);
1071
1072                 PIN_SLP(gpy5-0, INPUT, DOWN);
1073                 PIN_SLP(gpy5-1, INPUT, DOWN);
1074                 PIN_SLP(gpy5-2, INPUT, DOWN);
1075                 PIN_SLP(gpy5-3, INPUT, DOWN);
1076                 PIN_SLP(gpy5-4, INPUT, DOWN);
1077                 PIN_SLP(gpy5-5, INPUT, DOWN);
1078                 PIN_SLP(gpy5-6, INPUT, DOWN);
1079                 PIN_SLP(gpy5-7, INPUT, DOWN);
1080
1081                 PIN_SLP(gpy6-0, INPUT, DOWN);
1082                 PIN_SLP(gpy6-1, INPUT, DOWN);
1083                 PIN_SLP(gpy6-2, INPUT, DOWN);
1084                 PIN_SLP(gpy6-3, INPUT, DOWN);
1085                 PIN_SLP(gpy6-4, INPUT, DOWN);
1086                 PIN_SLP(gpy6-5, INPUT, DOWN);
1087                 PIN_SLP(gpy6-6, INPUT, DOWN);
1088                 PIN_SLP(gpy6-7, INPUT, DOWN);
1089         };
1090 };
1091
1092 &pinctrl_2 {
1093         pinctrl-names = "default";
1094         pinctrl-0 = <&sleep2>;
1095
1096         sleep2: sleep-state {
1097                 PIN_SLP(gpz-0, INPUT, DOWN);
1098                 PIN_SLP(gpz-1, INPUT, DOWN);
1099                 PIN_SLP(gpz-2, INPUT, DOWN);
1100                 PIN_SLP(gpz-3, INPUT, DOWN);
1101                 PIN_SLP(gpz-4, INPUT, DOWN);
1102                 PIN_SLP(gpz-5, INPUT, DOWN);
1103                 PIN_SLP(gpz-6, INPUT, DOWN);
1104         };
1105 };
1106
1107 &pinctrl_3 {
1108         pinctrl-names = "default";
1109         pinctrl-0 = <&sleep3>;
1110
1111         sleep3: sleep-state {
1112                 PIN_SLP(gpv0-0, INPUT, DOWN);
1113                 PIN_SLP(gpv0-1, INPUT, DOWN);
1114                 PIN_SLP(gpv0-2, INPUT, DOWN);
1115                 PIN_SLP(gpv0-3, INPUT, DOWN);
1116                 PIN_SLP(gpv0-4, INPUT, DOWN);
1117                 PIN_SLP(gpv0-5, INPUT, DOWN);
1118                 PIN_SLP(gpv0-6, INPUT, DOWN);
1119                 PIN_SLP(gpv0-7, INPUT, DOWN);
1120
1121                 PIN_SLP(gpv1-0, INPUT, DOWN);
1122                 PIN_SLP(gpv1-1, INPUT, DOWN);
1123                 PIN_SLP(gpv1-2, INPUT, DOWN);
1124                 PIN_SLP(gpv1-3, INPUT, DOWN);
1125                 PIN_SLP(gpv1-4, INPUT, DOWN);
1126                 PIN_SLP(gpv1-5, INPUT, DOWN);
1127                 PIN_SLP(gpv1-6, INPUT, DOWN);
1128                 PIN_SLP(gpv1-7, INPUT, DOWN);
1129
1130                 PIN_SLP(gpv2-0, INPUT, DOWN);
1131                 PIN_SLP(gpv2-1, INPUT, DOWN);
1132                 PIN_SLP(gpv2-2, INPUT, DOWN);
1133                 PIN_SLP(gpv2-3, INPUT, DOWN);
1134                 PIN_SLP(gpv2-4, INPUT, DOWN);
1135                 PIN_SLP(gpv2-5, INPUT, DOWN);
1136                 PIN_SLP(gpv2-6, INPUT, DOWN);
1137                 PIN_SLP(gpv2-7, INPUT, DOWN);
1138
1139                 PIN_SLP(gpv3-0, INPUT, DOWN);
1140                 PIN_SLP(gpv3-1, INPUT, DOWN);
1141                 PIN_SLP(gpv3-2, INPUT, DOWN);
1142                 PIN_SLP(gpv3-3, INPUT, DOWN);
1143                 PIN_SLP(gpv3-4, INPUT, DOWN);
1144                 PIN_SLP(gpv3-5, INPUT, DOWN);
1145                 PIN_SLP(gpv3-6, INPUT, DOWN);
1146                 PIN_SLP(gpv3-7, INPUT, DOWN);
1147
1148                 PIN_SLP(gpv4-0, INPUT, DOWN);
1149                 PIN_SLP(gpv4-1, INPUT, DOWN);
1150         };
1151 };
1152
1153 &pmu_system_controller {
1154         assigned-clocks = <&pmu_system_controller 0>;
1155         assigned-clock-parents = <&clock CLK_XUSBXTI>;
1156 };
1157
1158 &pwm {
1159         pinctrl-0 = <&pwm1_out>;
1160         pinctrl-names = "default";
1161         samsung,pwm-outputs = <1>;
1162         status = "okay";
1163 };
1164
1165 &rtc {
1166         clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
1167         clock-names = "rtc", "rtc_src";
1168         status = "okay";
1169 };
1170
1171 &sdhci_2 {
1172         bus-width = <4>;
1173         cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
1174         pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
1175         pinctrl-names = "default";
1176         vmmc-supply = <&ldo21_reg>;
1177         status = "okay";
1178 };
1179
1180 &sdhci_3 {
1181         #address-cells = <1>;
1182         #size-cells = <0>;
1183         non-removable;
1184         bus-width = <4>;
1185         mmc-pwrseq = <&wlan_pwrseq>;
1186
1187         pinctrl-names = "default";
1188         pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>;
1189         status = "okay";
1190
1191         wifi@1 {
1192                 compatible = "brcm,bcm4329-fmac";
1193                 reg = <0x1>;
1194                 pinctrl-names = "default";
1195                 pinctrl-0 = <&wifi_host_wake>;
1196                 interrupt-parent = <&gpx2>;
1197                 interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
1198                 interrupt-names = "host-wake";
1199         };
1200 };
1201
1202 &serial_0 {
1203         pinctrl-0 = <&uart0_data &uart0_fctl>;
1204         pinctrl-names = "default";
1205         status = "okay";
1206
1207         bluetooth {
1208                 compatible = "brcm,bcm4330-bt";
1209                 pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
1210                 pinctrl-names = "default";
1211
1212                 max-speed = <2000000>;
1213                 shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
1214                 device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
1215                 host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
1216                 clocks = <&max77686 MAX77686_CLK_PMIC>;
1217                 clock-names = "lpo";
1218         };
1219 };
1220
1221 &serial_2 {
1222         pinctrl-0 = <&uart_sel>;
1223         pinctrl-names = "default";
1224         status = "okay";
1225 };
1226
1227 &tmu {
1228         status = "okay";
1229 };