src/arm/ti/omap/logicpd-som-lv.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-only
   2
   3 #include <dt-bindings/input/input.h>
   4
   5 / {
   6         cpus {
   7                 cpu@0 {
   8                         cpu0-supply = <&vcc>;
   9                 };
  10         };
  11
  12         memory@80000000 {
  13                 device_type = "memory";
  14                 reg = <0x80000000 0>;
  15         };
  16
  17         wl12xx_vmmc: wl12xx_vmmc {
  18                 compatible = "regulator-fixed";
  19                 regulator-name = "vwl1271";
  20                 regulator-min-microvolt = <1800000>;
  21                 regulator-max-microvolt = <1800000>;
  22                 gpio = <&gpio1 3 0>;   /* gpio_3 */
  23                 startup-delay-us = <70000>;
  24                 enable-active-high;
  25                 vin-supply = <&vaux3>;
  26         };
  27
  28         /* HS USB Host PHY on PORT 1 */
  29         hsusb2_phy: hsusb2_phy {
  30                 pinctrl-names = "default";
  31                 pinctrl-0 = <&hsusb2_reset_pin>;
  32                 compatible = "usb-nop-xceiv";
  33                 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
  34                 #phy-cells = <0>;
  35         };
  36
  37         /* fixed 26MHz oscillator */
  38         hfclk_26m: oscillator {
  39                 #clock-cells = <0>;
  40                 compatible = "fixed-clock";
  41                 clock-frequency = <26000000>;
  42         };
  43 };
  44
  45 &gpmc {
  46         ranges = <0 0 0x30000000 0x1000000>;    /* CS0: 16MB for NAND */
  47
  48         nand@0,0 {
  49                 compatible = "ti,omap2-nand";
  50                 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
  51                 interrupt-parent = <&gpmc>;
  52                 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
  53                              <1 IRQ_TYPE_NONE>; /* termcount */
  54                 linux,mtd-name = "micron,mt29f4g16abbda3w";
  55                 nand-bus-width = <16>;
  56                 ti,nand-ecc-opt = "bch8";
  57                 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
  58                 gpmc,sync-clk-ps = <0>;
  59                 gpmc,cs-on-ns = <0>;
  60                 gpmc,cs-rd-off-ns = <44>;
  61                 gpmc,cs-wr-off-ns = <44>;
  62                 gpmc,adv-on-ns = <6>;
  63                 gpmc,adv-rd-off-ns = <34>;
  64                 gpmc,adv-wr-off-ns = <44>;
  65                 gpmc,we-off-ns = <40>;
  66                 gpmc,oe-off-ns = <54>;
  67                 gpmc,access-ns = <64>;
  68                 gpmc,rd-cycle-ns = <82>;
  69                 gpmc,wr-cycle-ns = <82>;
  70                 gpmc,wr-access-ns = <40>;
  71                 gpmc,wr-data-mux-bus-ns = <0>;
  72                 gpmc,device-width = <2>;
  73                 #address-cells = <1>;
  74                 #size-cells = <1>;
  75         };
  76 };
  77
  78 &i2c1 {
  79         pinctrl-names = "default";
  80         pinctrl-0 = <&i2c1_pins>;
  81         clock-frequency = <2600000>;
  82
  83         twl: twl@48 {
  84                 reg = <0x48>;
  85                 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
  86                 interrupt-parent = <&intc>;
  87                 clocks = <&hfclk_26m>;
  88                 clock-names = "fck";
  89                 twl_audio: audio {
  90                         compatible = "ti,twl4030-audio";
  91                         codec {
  92                                 ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
  93                         };
  94                 };
  95         };
  96 };
  97
  98 &i2c2 {
  99         pinctrl-names = "default";
 100         pinctrl-0 = <&i2c2_pins>;
 101         clock-frequency = <400000>;
 102 };
 103
 104 &i2c3 {
 105         pinctrl-names = "default";
 106         pinctrl-0 = <&i2c3_pins>;
 107         clock-frequency = <400000>;
 108
 109         touchscreen: tsc2004@48 {
 110                 compatible = "ti,tsc2004";
 111                 reg = <0x48>;
 112                 vio-supply = <&vaux1>;
 113                 pinctrl-names = "default";
 114                 pinctrl-0 = <&tsc2004_pins>;
 115                 interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */
 116
 117                 touchscreen-fuzz-x = <4>;
 118                 touchscreen-fuzz-y = <7>;
 119                 touchscreen-fuzz-pressure = <2>;
 120                 touchscreen-size-x = <4096>;
 121                 touchscreen-size-y = <4096>;
 122                 touchscreen-max-pressure = <2048>;
 123
 124                 ti,x-plate-ohms = <280>;
 125                 ti,esd-recovery-timeout-ms = <8000>;
 126         };
 127 };
 128
 129 &mmc3 {
 130         interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>;
 131         pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
 132         pinctrl-names = "default";
 133         vmmc-supply = <&wl12xx_vmmc>;
 134         non-removable;
 135         bus-width = <4>;
 136         cap-power-off-card;
 137         #address-cells = <1>;
 138         #size-cells = <0>;
 139         wlcore: wlcore@2 {
 140                 compatible = "ti,wl1273";
 141                 reg = <2>;
 142                 interrupt-parent = <&gpio1>;
 143                 interrupts = <2 IRQ_TYPE_EDGE_RISING>; /* gpio 2 */
 144                 ref-clock-frequency = <26000000>;
 145         };
 146 };
 147
 148 &usbhshost {
 149         pinctrl-names = "default";
 150         pinctrl-0 = <&hsusb2_pins>;
 151         port2-mode = "ehci-phy";
 152 };
 153
 154 &usbhsehci {
 155         phys = <0 &hsusb2_phy>;
 156 };
 157
 158 &omap3_pmx_core {
 159
 160         mmc3_pins: mm3-pins {
 161                 pinctrl-single,pins = <
 162                         OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
 163                         OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
 164                         OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
 165                         OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
 166                         OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
 167                         OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
 168                 >;
 169         };
 170         mcbsp2_pins: mcbsp2-pins {
 171                 pinctrl-single,pins = <
 172                         OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0)        /* mcbsp2_fsx */
 173                         OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0)        /* mcbsp2_clkx */
 174                         OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0)        /* mcbsp2_dr */
 175                         OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0)       /* mcbsp2_dx */
 176                 >;
 177         };
 178         uart2_pins: uart2-pins {
 179                 pinctrl-single,pins = <
 180                         OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0)        /* uart2_cts.uart2_cts */
 181                         OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)       /* uart2_rts .uart2_rts*/
 182                         OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)       /* uart2_tx.uart2_tx */
 183                         OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)        /* uart2_rx.uart2_rx */
 184                         OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4)       /* GPIO_162,BT_EN */
 185                 >;
 186         };
 187         mcspi1_pins: mcspi1-pins {
 188                 pinctrl-single,pins = <
 189                         OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)        /* mcspi1_clk.mcspi1_clk */
 190                         OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_simo.mcspi1_simo */
 191                         OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
 192                         OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0)       /* mcspi1_cs0.mcspi1_cs0 */
 193                 >;
 194         };
 195
 196         hsusb2_pins: hsusb2-pins {
 197                 pinctrl-single,pins = <
 198                         OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi1_cs3.hsusb2_data2 */
 199                         OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_clk.hsusb2_data7 */
 200                         OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_simo.hsusb2_data4 */
 201                         OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_somi.hsusb2_data5 */
 202                         OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs0.hsusb2_data6 */
 203                         OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)       /* mcspi2_cs1.hsusb2_data3 */
 204                 >;
 205         };
 206
 207         hsusb_otg_pins: hsusb-otg-pins {
 208                 pinctrl-single,pins = <
 209                         OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0)        /* hsusb0_clk.hsusb0_clk */
 210                         OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)       /* hsusb0_stp.hsusb0_stp */
 211                         OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0)        /* hsusb0_dir.hsusb0_dir */
 212                         OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0)        /* hsusb0_nxt.hsusb0_nxt */
 213                         OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0)        /* hsusb0_data0.hsusb0_data0 */
 214                         OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0)        /* hsusb0_data1.hsusb0_data1 */
 215                         OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0)        /* hsusb0_data2.hsusb0_data2 */
 216                         OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0)        /* hsusb0_data3.hsusb0_data3 */
 217                         OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0)        /* hsusb0_data4.hsusb0_data4 */
 218                         OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0)        /* hsusb0_data5.hsusb0_data5 */
 219                         OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0)        /* hsusb0_data6.hsusb0_data6 */
 220                         OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0)        /* hsusb0_data7.hsusb0_data7 */
 221                 >;
 222         };
 223
 224         i2c1_pins: i2c1-pins {
 225                 pinctrl-single,pins = <
 226                         OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
 227                         OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
 228                         OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4)        /* gpmc_ncs6.gpio_57 */
 229                 >;
 230         };
 231
 232         i2c2_pins: i2c2-pins {
 233                 pinctrl-single,pins = <
 234                         OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0)        /* i2c2_scl */
 235                         OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0)        /* i2c2_sda */
 236                 >;
 237         };
 238
 239         i2c3_pins: i2c3-pins {
 240                 pinctrl-single,pins = <
 241                         OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0)        /* i2c3_scl */
 242                         OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0)        /* i2c3_sda */
 243                 >;
 244         };
 245
 246         tsc2004_pins: tsc2004-pins {
 247                 pinctrl-single,pins = <
 248                         OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4)        /* mcbsp4_dr.gpio_153 */
 249                 >;
 250         };
 251 };
 252
 253 &omap3_pmx_wkup {
 254
 255         hsusb2_reset_pin: hsusb1-reset-pins {
 256                 pinctrl-single,pins = <
 257                         OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)        /* sys_boot2.gpio_4 */
 258                 >;
 259         };
 260         wl127x_gpio: wl127x-gpio-pins {
 261                 pinctrl-single,pins = <
 262                         OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4)         /* sys_boot0.gpio_2 */
 263                         OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)        /* sys_boot1.gpio_3 */
 264                 >;
 265         };
 266 };
 267
 268 &uart2 {
 269         interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 270         pinctrl-names = "default";
 271         pinctrl-0 = <&uart2_pins>;
 272 };
 273
 274 &mcspi1 {
 275         pinctrl-names = "default";
 276         pinctrl-0 = <&mcspi1_pins>;
 277 };
 278
 279 #include "twl4030.dtsi"
 280 #include "twl4030_omap3.dtsi"
 281
 282 &vaux3 {
 283         regulator-min-microvolt = <2800000>;
 284         regulator-max-microvolt = <2800000>;
 285 };
 286
 287 &twl {
 288         twl_power: power {
 289                 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
 290                 ti,use_poweroff;
 291         };
 292 };
 293
 294 &twl_gpio {
 295         ti,use-leds;
 296 };