src/arm64/qcom/msm8939-longcheer-l9100.dts

   1 // SPDX-License-Identifier: GPL-2.0-only
   2
   3 /dts-v1/;
   4
   5 #include "msm8939-pm8916.dtsi"
   6
   7 #include <dt-bindings/gpio/gpio.h>
   8 #include <dt-bindings/input/input.h>
   9 #include <dt-bindings/interrupt-controller/irq.h>
  10 #include <dt-bindings/leds/common.h>
  11 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
  12 #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
  13
  14 / {
  15         model = "BQ Aquaris M5 (Longcheer L9100)";
  16         compatible = "longcheer,l9100", "qcom,msm8939";
  17         chassis-type = "handset";
  18
  19         aliases {
  20                 mmc0 = &sdhc_1; /* eMMC */
  21                 mmc1 = &sdhc_2; /* SD card */
  22                 serial0 = &blsp_uart2;
  23         };
  24
  25         chosen {
  26                 stdout-path = "serial0";
  27         };
  28
  29         gpio-hall-sensor {
  30                 compatible = "gpio-keys";
  31
  32                 pinctrl-0 = <&gpio_hall_sensor_default>;
  33                 pinctrl-names = "default";
  34
  35                 label = "GPIO Hall Effect Sensor";
  36
  37                 event-hall-sensor {
  38                         label = "Hall Effect Sensor";
  39                         gpios = <&tlmm 20 GPIO_ACTIVE_LOW>;
  40                         linux,input-type = <EV_SW>;
  41                         linux,code = <SW_LID>;
  42                         linux,can-disable;
  43                 };
  44         };
  45
  46         gpio-keys {
  47                 compatible = "gpio-keys";
  48
  49                 pinctrl-0 = <&gpio_keys_default>;
  50                 pinctrl-names = "default";
  51
  52                 label = "GPIO Buttons";
  53
  54                 button-volume-up {
  55                         label = "Volume Up";
  56                         gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
  57                         linux,code = <KEY_VOLUMEUP>;
  58                 };
  59         };
  60
  61         leds {
  62                 compatible = "gpio-leds";
  63
  64                 led-0 {
  65                         gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>;
  66                         color = <LED_COLOR_ID_WHITE>;
  67                         default-state = "off";
  68                         function = LED_FUNCTION_KBD_BACKLIGHT;
  69
  70                         pinctrl-0 = <&button_backlight_default>;
  71                         pinctrl-names = "default";
  72                 };
  73         };
  74
  75         reg_ts_vdd: regulator-vdd-ts {
  76                 compatible = "regulator-fixed";
  77                 regulator-name = "regulator-vdd-ts";
  78                 regulator-min-microvolt = <2850000>;
  79                 regulator-max-microvolt = <2850000>;
  80
  81                 gpio = <&tlmm 78 GPIO_ACTIVE_HIGH>;
  82                 enable-active-high;
  83
  84                 pinctrl-0 = <&ts_vdd_default>;
  85                 pinctrl-names = "default";
  86         };
  87
  88         backlight {
  89                 compatible = "pwm-backlight";
  90                 pwms = <&pm8916_pwm 0 100000>;
  91                 brightness-levels = <0 255>;
  92                 num-interpolated-steps = <255>;
  93                 default-brightness-level = <128>;
  94                 enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
  95
  96                 pinctrl-0 = <&lcd_bl_en_default>;
  97                 pinctrl-names = "default";
  98         };
  99
 100         flash-led-controller {
 101                 compatible = "ocs,ocp8110";
 102                 flash-gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>;
 103                 enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;
 104
 105                 pinctrl-0 = <&camera_front_flash_default>;
 106                 pinctrl-names = "default";
 107
 108                 led {
 109                         function = LED_FUNCTION_FLASH;
 110                         color = <LED_COLOR_ID_WHITE>;
 111                         flash-max-timeout-us = <250000>;
 112                 };
 113         };
 114
 115         usb_id: usb-id {
 116                 compatible = "linux,extcon-usb-gpio";
 117                 id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
 118                 pinctrl-0 = <&usb_id_default &usb_id_switch_default>;
 119                 pinctrl-names = "default";
 120         };
 121
 122 };
 123
 124 &blsp_i2c2 {
 125         status = "okay";
 126
 127         led-controller@30 {
 128                 compatible = "kinetic,ktd2026";
 129                 reg = <0x30>;
 130                 #address-cells = <1>;
 131                 #size-cells = <0>;
 132
 133                 vin-supply = <&pm8916_l17>;
 134                 vio-supply = <&pm8916_l6>;
 135
 136                 pinctrl-0 = <&status_led_default>;
 137                 pinctrl-names = "default";
 138
 139                 multi-led {
 140                         color = <LED_COLOR_ID_RGB>;
 141                         function = LED_FUNCTION_STATUS;
 142
 143                         #address-cells = <1>;
 144                         #size-cells = <0>;
 145
 146                         led@0 {
 147                                 reg = <0>;
 148                                 color = <LED_COLOR_ID_RED>;
 149                         };
 150
 151                         led@1 {
 152                                 reg = <1>;
 153                                 color = <LED_COLOR_ID_GREEN>;
 154                         };
 155
 156                         led@2 {
 157                                 reg = <2>;
 158                                 color = <LED_COLOR_ID_BLUE>;
 159                         };
 160                 };
 161         };
 162 };
 163
 164 &blsp_i2c3 {
 165         status = "okay";
 166
 167         magnetometer@d {
 168                 compatible = "asahi-kasei,ak09911";
 169                 reg = <0x0d>;
 170
 171                 vdd-supply = <&pm8916_l17>;
 172                 vid-supply = <&pm8916_l6>;
 173
 174                 reset-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>;
 175
 176                 pinctrl-0 = <&mag_reset_default>;
 177                 pinctrl-names = "default";
 178         };
 179
 180         light-sensor@23 {
 181                 compatible = "liteon,ltr559";
 182                 reg = <0x23>;
 183                 proximity-near-level = <75>;
 184
 185                 vdd-supply = <&pm8916_l17>;
 186                 vddio-supply = <&pm8916_l5>;
 187
 188                 interrupts-extended = <&tlmm 113 IRQ_TYPE_EDGE_FALLING>;
 189
 190                 pinctrl-0 = <&light_int_default>;
 191                 pinctrl-names = "default";
 192         };
 193
 194         imu@68 {
 195                 compatible = "bosch,bmi160";
 196                 reg = <0x68>;
 197
 198                 vdd-supply = <&pm8916_l17>;
 199                 vddio-supply = <&pm8916_l6>;
 200         };
 201 };
 202
 203 &blsp_i2c5 {
 204         status = "okay";
 205
 206         touchscreen@4a {
 207                 compatible = "atmel,maxtouch";
 208                 reg = <0x4a>;
 209
 210                 interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
 211
 212                 reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
 213
 214                 vdda-supply = <&pm8916_l6>;
 215                 vdd-supply = <&reg_ts_vdd>;
 216
 217                 pinctrl-0 = <&ts_int_reset_default>;
 218                 pinctrl-names = "default";
 219
 220                 /* Keys listed from right to left */
 221                 linux,keycodes = <KEY_APPSELECT KEY_HOMEPAGE KEY_BACK>;
 222         };
 223 };
 224
 225 &blsp_uart2 {
 226         status = "okay";
 227 };
 228
 229 &pm8916_gpios {
 230         status_led_default: status-led-default-state {
 231                 pins = "gpio3";
 232                 function = PMIC_GPIO_FUNC_NORMAL;
 233                 power-source = <PM8916_GPIO_VPH>;
 234                 bias-disable;
 235                 output-high;
 236         };
 237 };
 238
 239 &pm8916_mpps {
 240         pwm_out: mpp4-state {
 241                 pins = "mpp4";
 242                 function = "digital";
 243                 power-source = <PM8916_MPP_VPH>;
 244                 output-low;
 245                 qcom,dtest = <1>;
 246         };
 247 };
 248
 249 &pm8916_pwm {
 250         pinctrl-0 = <&pwm_out>;
 251         pinctrl-names = "default";
 252         status = "okay";
 253 };
 254
 255 &pm8916_resin {
 256         linux,code = <KEY_VOLUMEDOWN>;
 257         status = "okay";
 258 };
 259
 260 &pm8916_rpm_regulators {
 261         pm8916_l17: l17 {
 262                 regulator-min-microvolt = <2850000>;
 263                 regulator-max-microvolt = <2850000>;
 264         };
 265 };
 266
 267 &pm8916_vib {
 268         status = "okay";
 269 };
 270
 271 &sdhc_1 {
 272         status = "okay";
 273 };
 274
 275 &sdhc_2 {
 276         pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
 277         pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
 278         pinctrl-names = "default", "sleep";
 279
 280         cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 281
 282         status = "okay";
 283 };
 284
 285 &usb {
 286         extcon = <&usb_id>, <&usb_id>;
 287         status = "okay";
 288 };
 289
 290 &usb_hs_phy {
 291         extcon = <&usb_id>;
 292 };
 293
 294 &wcnss {
 295         status = "okay";
 296 };
 297
 298 &wcnss_iris {
 299         compatible = "qcom,wcn3620";
 300 };
 301
 302 &wcnss_mem {
 303         status = "okay";
 304 };
 305
 306 &tlmm {
 307         button_backlight_default: button-backlight-default-state {
 308                 pins = "gpio17";
 309                 function = "gpio";
 310                 drive-strength = <2>;
 311                 bias-disable;
 312         };
 313
 314         camera_front_flash_default: camera-front-flash-default-state {
 315                 pins = "gpio8", "gpio49";
 316                 function = "gpio";
 317                 drive-strength = <2>;
 318                 bias-disable;
 319         };
 320
 321         gpio_hall_sensor_default: gpio-hall-sensor-default-state {
 322                 pins = "gpio20";
 323                 function = "gpio";
 324                 drive-strength = <2>;
 325                 bias-disable;
 326         };
 327
 328         gpio_keys_default: gpio-keys-default-state {
 329                 pins = "gpio107";
 330                 function = "gpio";
 331                 drive-strength = <2>;
 332                 bias-pull-up;
 333         };
 334
 335         lcd_bl_en_default: lcd-bl-en-default-state {
 336                 pins = "gpio98";
 337                 function = "gpio";
 338                 drive-strength = <2>;
 339                 bias-disable;
 340         };
 341
 342         light_int_default: light-int-default-state {
 343                 pins = "gpio113";
 344                 function = "gpio";
 345                 drive-strength = <2>;
 346                 bias-disable;
 347         };
 348
 349         mag_reset_default: mag-reset-default-state {
 350                 pins = "gpio68";
 351                 function = "gpio";
 352                 drive-strength = <2>;
 353                 bias-disable;
 354         };
 355
 356         sdc2_cd_default: sdc2-cd-default-state {
 357                 pins = "gpio38";
 358                 function = "gpio";
 359                 drive-strength = <2>;
 360                 bias-disable;
 361         };
 362
 363         ts_int_reset_default: ts-int-reset-default-state {
 364                 pins = "gpio12", "gpio13";
 365                 function = "gpio";
 366                 drive-strength = <2>;
 367                 bias-disable;
 368         };
 369
 370         ts_vdd_default: ts-vdd-default-state {
 371                 pins = "gpio78";
 372                 function = "gpio";
 373                 drive-strength = <2>;
 374                 bias-disable;
 375         };
 376
 377         usb_id_default: usb-id-default-state {
 378                 pins = "gpio110";
 379                 function = "gpio";
 380                 drive-strength = <8>;
 381                 bias-pull-up;
 382         };
 383
 384         usb_id_switch_default: usb-id-switch-default-state {
 385                 pins = "gpio121";
 386                 function = "gpio";
 387                 drive-strength = <2>;
 388                 output-high;
 389         };
 390 };