src/arm64/qcom/sc7180-trogdor.dtsi

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Google Trogdor device tree source (common between revisions)
   4  *
   5  * Copyright 2019 Google LLC.
   6  */
   7
   8 #include <dt-bindings/gpio/gpio.h>
   9 #include <dt-bindings/input/gpio-keys.h>
  10 #include <dt-bindings/input/input.h>
  11 #include <dt-bindings/leds/common.h>
  12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  13 #include <dt-bindings/sound/sc7180-lpass.h>
  14
  15 #include "sc7180.dtsi"
  16 #include "sc7180-firmware-tfa.dtsi"
  17 /* PMICs depend on spmi_bus label and so must come after sc7180.dtsi */
  18 #include "pm6150.dtsi"
  19 #include "pm6150l.dtsi"
  20
  21 / {
  22         thermal-zones {
  23                 charger_thermal: charger-thermal {
  24                         polling-delay-passive = <0>;
  25                         polling-delay = <0>;
  26
  27                         thermal-sensors = <&pm6150_adc_tm 0>;
  28
  29                         trips {
  30                                 charger-crit {
  31                                         temperature = <125000>;
  32                                         hysteresis = <1000>;
  33                                         type = "critical";
  34                                 };
  35                         };
  36                 };
  37         };
  38 };
  39
  40 /*
  41  * Reserved memory changes
  42  *
  43  * Delete all unused memory nodes and define the peripheral memory regions
  44  * required by the board dts.
  45  */
  46
  47 /delete-node/ &hyp_mem;
  48 /delete-node/ &ipa_fw_mem;
  49 /delete-node/ &xbl_mem;
  50 /delete-node/ &aop_mem;
  51 /delete-node/ &sec_apps_mem;
  52 /delete-node/ &tz_mem;
  53
  54 /* Increase the size from 2MB to 8MB */
  55 &rmtfs_mem {
  56         reg = <0x0 0x94600000 0x0 0x800000>;
  57 };
  58
  59 / {
  60         reserved-memory {
  61                 atf_mem: memory@80b00000 {
  62                         reg = <0x0 0x80b00000 0x0 0x100000>;
  63                         no-map;
  64                 };
  65
  66                 mpss_mem: memory@86000000 {
  67                         reg = <0x0 0x86000000 0x0 0x2000000>;
  68                         no-map;
  69                 };
  70
  71                 venus_mem: memory@8f600000 {
  72                         reg = <0 0x8f600000 0 0x500000>;
  73                         no-map;
  74                 };
  75
  76                 wlan_mem: memory@94100000 {
  77                         reg = <0x0 0x94100000 0x0 0x200000>;
  78                         no-map;
  79                 };
  80
  81                 mba_mem: memory@94400000 {
  82                         reg = <0x0 0x94400000 0x0 0x200000>;
  83                         no-map;
  84                 };
  85
  86                 mdata_mem: mpss-metadata {
  87                         alloc-ranges = <0x0 0xa0000000 0x0 0x20000000>;
  88                         size = <0x0 0x4000>;
  89                         no-map;
  90                 };
  91         };
  92
  93         aliases {
  94                 bluetooth0 = &bluetooth;
  95                 hsuart0 = &uart3;
  96                 serial0 = &uart8;
  97                 wifi0 = &wifi;
  98         };
  99
 100         chosen {
 101                 stdout-path = "serial0:115200n8";
 102         };
 103
 104         /* FIXED REGULATORS - parents above children */
 105
 106         /* This is the top level supply and variable voltage */
 107         ppvar_sys: ppvar-sys-regulator {
 108                 compatible = "regulator-fixed";
 109                 regulator-name = "ppvar_sys";
 110                 regulator-always-on;
 111                 regulator-boot-on;
 112         };
 113
 114         /* This divides ppvar_sys by 2, so voltage is variable */
 115         src_vph_pwr: src-vph-pwr-regulator {
 116                 compatible = "regulator-fixed";
 117                 regulator-name = "src_vph_pwr";
 118
 119                 /* EC turns on with switchcap_on; always on for AP */
 120                 regulator-always-on;
 121                 regulator-boot-on;
 122
 123                 vin-supply = <&ppvar_sys>;
 124         };
 125
 126         pp5000_a: pp5000-a-regulator {
 127                 compatible = "regulator-fixed";
 128                 regulator-name = "pp5000_a";
 129
 130                 /* EC turns on with en_pp5000_a; always on for AP */
 131                 regulator-always-on;
 132                 regulator-boot-on;
 133                 regulator-min-microvolt = <5000000>;
 134                 regulator-max-microvolt = <5000000>;
 135
 136                 vin-supply = <&ppvar_sys>;
 137         };
 138
 139         pp3300_a: pp3300-a-regulator {
 140                 compatible = "regulator-fixed";
 141                 regulator-name = "pp3300_a";
 142
 143                 /* EC turns on with en_pp3300_a; always on for AP */
 144                 regulator-always-on;
 145                 regulator-boot-on;
 146                 regulator-min-microvolt = <3300000>;
 147                 regulator-max-microvolt = <3300000>;
 148
 149                 /*
 150                  * Actually should be pp3300 but that's practically an alias for
 151                  * pp3300_a so we use pp3300's vin-supply here to avoid one more
 152                  * node.
 153                  */
 154                 vin-supply = <&ppvar_sys>;
 155         };
 156
 157         pp1800_ec:
 158         pp1800_sensors:
 159         pp1800_ldo: pp1800-ldo-regulator {
 160                 compatible = "regulator-fixed";
 161                 regulator-name = "pp1800_ldo";
 162
 163                 /* EC turns on with hibernate_l; always on for AP */
 164                 regulator-always-on;
 165                 regulator-boot-on;
 166                 regulator-min-microvolt = <1800000>;
 167                 regulator-max-microvolt = <1800000>;
 168
 169                 /*
 170                  * Actually should be pp1800_h1 but we don't have any need to
 171                  * model that so we use the parent of pp1800_h1.
 172                  */
 173                 vin-supply = <&pp3300_a>;
 174         };
 175
 176         pp1800_uf_cam: pp1800-uf-cam-regulator {
 177                 compatible = "regulator-fixed";
 178                 regulator-name = "pp1800_uf_cam";
 179                 status = "disabled";
 180
 181                 regulator-min-microvolt = <1800000>;
 182                 regulator-max-microvolt = <1800000>;
 183
 184                 gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
 185                 enable-active-high;
 186                 pinctrl-names = "default";
 187                 pinctrl-0 = <&uf_cam_en>;
 188
 189                 vin-supply = <&pp1800_ldo>;
 190                 regulator-enable-ramp-delay = <1000>;
 191         };
 192
 193         pp1800_wf_cam: pp1800-wf-cam-regulator {
 194                 compatible = "regulator-fixed";
 195                 regulator-name = "pp1800_wf_cam";
 196                 status = "disabled";
 197
 198                 regulator-min-microvolt = <1800000>;
 199                 regulator-max-microvolt = <1800000>;
 200
 201                 gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
 202                 enable-active-high;
 203                 pinctrl-names = "default";
 204                 pinctrl-0 = <&wf_cam_en>;
 205
 206                 vin-supply = <&pp1800_ldo>;
 207                 regulator-enable-ramp-delay = <1000>;
 208         };
 209
 210         pp2800_uf_cam: pp2800-uf-cam-regulator {
 211                 compatible = "regulator-fixed";
 212                 regulator-name = "pp2800_uf_cam";
 213                 status = "disabled";
 214
 215                 regulator-min-microvolt = <2850000>;
 216                 regulator-max-microvolt = <2850000>;
 217
 218                 gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
 219                 enable-active-high;
 220                 /*
 221                  * The pinconf can only be referenced once so we put it on the
 222                  * first regulator and comment it out here.
 223                  * pinctrl-names = "default";
 224                  * pinctrl-0 = <&uf_cam_en>;
 225                  */
 226
 227                 vin-supply = <&pp3300_a>;
 228         };
 229
 230         pp2800_vcm_wf_cam:
 231         pp2800_wf_cam: pp2800-wf-cam-regulator {
 232                 compatible = "regulator-fixed";
 233                 regulator-name = "pp2800_wf_cam";
 234                 status = "disabled";
 235
 236                 regulator-min-microvolt = <2850000>;
 237                 regulator-max-microvolt = <2850000>;
 238
 239                 gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
 240                 enable-active-high;
 241                 /*
 242                  * The pinconf can only be referenced once so we put it on the
 243                  * first regulator and comment it out here.
 244                  * pinctrl-names = "default";
 245                  * pinctrl-0 = <&wf_cam_en>;
 246                  */
 247
 248                 vin-supply = <&pp3300_a>;
 249         };
 250
 251         pp3300_audio:
 252         pp3300_codec: pp3300-codec-regulator {
 253                 compatible = "regulator-fixed";
 254                 regulator-name = "pp3300_codec";
 255
 256                 regulator-min-microvolt = <3300000>;
 257                 regulator-max-microvolt = <3300000>;
 258
 259                 gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>;
 260                 enable-active-high;
 261                 pinctrl-names = "default";
 262                 pinctrl-0 = <&en_pp3300_codec>;
 263
 264                 vin-supply = <&pp3300_a>;
 265         };
 266
 267         pp3300_dx_edp:
 268         pp3300_ts: pp3300-dx-edp-regulator {
 269                 compatible = "regulator-fixed";
 270                 regulator-name = "pp3300_dx_edp";
 271
 272                 regulator-min-microvolt = <3300000>;
 273                 regulator-max-microvolt = <3300000>;
 274
 275                 gpio = <&tlmm 30 GPIO_ACTIVE_HIGH>;
 276                 enable-active-high;
 277                 pinctrl-names = "default";
 278                 pinctrl-0 = <&en_pp3300_dx_edp>;
 279
 280                 vin-supply = <&pp3300_a>;
 281         };
 282
 283         pp3300_fp_tp: pp3300-fp-tp-regulator {
 284                 compatible = "regulator-fixed";
 285                 regulator-name = "pp3300_fp_tp";
 286
 287                 regulator-min-microvolt = <3300000>;
 288                 regulator-max-microvolt = <3300000>;
 289
 290                 /* AP turns on with PP1800_VIO_OUT; always on for AP */
 291                 regulator-always-on;
 292                 regulator-boot-on;
 293
 294                 vin-supply = <&pp3300_a>;
 295         };
 296
 297         pp3300_hub: pp3300-hub-regulator {
 298                 compatible = "regulator-fixed";
 299                 regulator-name = "pp3300_hub";
 300
 301                 regulator-min-microvolt = <3300000>;
 302                 regulator-max-microvolt = <3300000>;
 303
 304                 gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
 305                 enable-active-high;
 306                 pinctrl-names = "default";
 307                 pinctrl-0 = <&en_pp3300_hub>;
 308
 309                 /* The BIOS leaves this regulator on */
 310                 regulator-boot-on;
 311
 312                 vin-supply = <&pp3300_a>;
 313         };
 314
 315         /* BOARD-SPECIFIC TOP LEVEL NODES */
 316
 317         backlight: backlight {
 318                 compatible = "pwm-backlight";
 319
 320                 /* The panels don't seem to like anything below ~ 5% */
 321                 brightness-levels = <
 322                         196 256 324 400 484 576 676 784 900 1024 1156 1296
 323                         1444 1600 1764 1936 2116 2304 2500 2704 2916 3136
 324                         3364 3600 3844 4096
 325                 >;
 326                 num-interpolated-steps = <64>;
 327                 default-brightness-level = <951>;
 328
 329                 pwms = <&cros_ec_pwm 1>;
 330                 enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 331                 power-supply = <&ppvar_sys>;
 332                 pinctrl-names = "default";
 333                 pinctrl-0 = <&ap_edp_bklten>;
 334         };
 335
 336         gpio_keys: gpio-keys {
 337                 compatible = "gpio-keys";
 338                 status = "disabled";
 339                 pinctrl-names = "default";
 340                 pinctrl-0 = <&pen_pdct_l>;
 341
 342                 pen_insert: switch-pen-insert {
 343                         label = "Pen Insert";
 344
 345                         /* Insert = low, eject = high */
 346                         gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
 347                         linux,code = <SW_PEN_INSERTED>;
 348                         linux,input-type = <EV_SW>;
 349                         wakeup-event-action = <EV_ACT_DEASSERTED>;
 350                         wakeup-source;
 351                 };
 352         };
 353
 354         max98360a: audio-codec-0 {
 355                 compatible = "maxim,max98360a";
 356                 pinctrl-names = "default";
 357                 pinctrl-0 = <&amp_en>;
 358                 sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
 359                 #sound-dai-cells = <0>;
 360         };
 361
 362         pwmleds {
 363                 compatible = "pwm-leds";
 364                 keyboard_backlight: led-0 {
 365                         status = "disabled";
 366                         label = "cros_ec::kbd_backlight";
 367                         function = LED_FUNCTION_KBD_BACKLIGHT;
 368                         pwms = <&cros_ec_pwm 0>;
 369                         max-brightness = <1023>;
 370                 };
 371         };
 372
 373         sound: sound {
 374                 compatible = "google,sc7180-trogdor";
 375
 376                 audio-routing =
 377                         "Headphone Jack", "HPOL",
 378                         "Headphone Jack", "HPOR";
 379
 380                 #address-cells = <1>;
 381                 #size-cells = <0>;
 382
 383                 dai-link@0 {
 384                         link-name = "MultiMedia0";
 385                         reg = <MI2S_PRIMARY>;
 386                         cpu {
 387                                 sound-dai = <&lpass_cpu MI2S_PRIMARY>;
 388                         };
 389
 390                         sound_multimedia0_codec: codec {
 391                                 sound-dai = <&alc5682 0 /* aif1 */>;
 392                         };
 393                 };
 394
 395                 dai-link@1 {
 396                         link-name = "MultiMedia1";
 397                         reg = <MI2S_SECONDARY>;
 398                         cpu {
 399                                 sound-dai = <&lpass_cpu MI2S_SECONDARY>;
 400                         };
 401
 402                         sound_multimedia1_codec: codec {
 403                                 sound-dai = <&max98360a>;
 404                         };
 405                 };
 406
 407                 dai-link@5 {
 408                         link-name = "MultiMedia2";
 409                         reg = <LPASS_DP_RX>;
 410                         cpu {
 411                                 sound-dai = <&lpass_cpu LPASS_DP_RX>;
 412                         };
 413
 414                         codec {
 415                                 sound-dai = <&mdss_dp>;
 416                         };
 417                 };
 418         };
 419 };
 420
 421 &qfprom {
 422         vcc-supply = <&pp1800_l11a>;
 423 };
 424
 425 &qspi {
 426         status = "okay";
 427         pinctrl-names = "default", "sleep";
 428         pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data0>, <&qspi_data1>;
 429         pinctrl-1 = <&qspi_sleep>;
 430
 431         flash@0 {
 432                 compatible = "jedec,spi-nor";
 433                 reg = <0>;
 434
 435                 spi-max-frequency = <37500000>;
 436                 spi-tx-bus-width = <2>;
 437                 spi-rx-bus-width = <2>;
 438         };
 439 };
 440
 441 &apps_rsc {
 442         regulators-0 {
 443                 compatible = "qcom,pm6150-rpmh-regulators";
 444                 qcom,pmic-id = "a";
 445
 446                 vddpx_1:
 447                 vdd2:
 448                 pp1125_s1a: smps1 {
 449                         regulator-min-microvolt = <1128000>;
 450                         regulator-max-microvolt = <1128000>;
 451                 };
 452
 453                 vdd_qlink_lv:
 454                 vdd_qlink_lv_ck:
 455                 vdd_qusb_hs0_core:
 456                 vdd_ufs1_core:
 457                 vdda_mipi_csi0_0p9:
 458                 vdda_mipi_csi1_0p9:
 459                 vdda_mipi_csi2_0p9:
 460                 vdda_mipi_csi3_0p9:
 461                 vdda_mipi_dsi0_pll:
 462                 vdda_pll_cc_ebi01:
 463                 vdda_qrefs_0p9:
 464                 vdda_usb_ss_dp_core:
 465                 pp900_l4a: ldo4 {
 466                         regulator-min-microvolt = <824000>;
 467                         regulator-max-microvolt = <928000>;
 468                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 469                 };
 470
 471                 vdd_cx_wlan:
 472                 pp800_l9a: ldo9 {
 473                         regulator-min-microvolt = <488000>;
 474                         regulator-max-microvolt = <800000>;
 475                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 476                 };
 477
 478                 vdd1:
 479                 vddpx_3:
 480                 vddpx_7:
 481                 vio_in:
 482                 pp1800_l10a: ldo10 {
 483                         regulator-min-microvolt = <1800000>;
 484                         regulator-max-microvolt = <1800000>;
 485                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 486                 };
 487
 488                 vdd_qfprom:
 489                 vdda_apc1_cs_1p8:
 490                 vdda_qrefs_1p8:
 491                 vdda_qusb_hs0_1p8:
 492                 vddpx_11:
 493                 vreg_bb_clk:
 494                 pp1800_l11a: ldo11 {
 495                         regulator-min-microvolt = <1800000>;
 496                         regulator-max-microvolt = <1800000>;
 497                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 498                 };
 499
 500                 mcp_vccq:
 501                 pp1800_l12a_r: ldo12 {
 502                         regulator-min-microvolt = <1800000>;
 503                         regulator-max-microvolt = <1800000>;
 504                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 505                 };
 506
 507                 /*
 508                  * On trogdor this needs to match l10a since we use it to
 509                  * give power to things like SPI flash which communicate back
 510                  * on lines powered by l10a.  Thus we force to 1.8V.
 511                  */
 512                 pp1800_l13a: ldo13 {
 513                         regulator-min-microvolt = <1800000>;
 514                         regulator-max-microvolt = <1800000>;
 515                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 516                         regulator-always-on;
 517                         regulator-boot-on;
 518                 };
 519
 520                 pp1800_prox:
 521                 pp1800_l14a: ldo14 {
 522                         regulator-min-microvolt = <1800000>;
 523                         regulator-max-microvolt = <1800000>;
 524                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 525                 };
 526
 527                 pp1800_alc5682:
 528                 pp1800_l15a: ldo15 {
 529                         regulator-min-microvolt = <1800000>;
 530                         regulator-max-microvolt = <1800000>;
 531                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 532                 };
 533
 534                 vdda_qusb_hs0_3p1:
 535                 vdd_pdphy:
 536                 pp3100_l17a: ldo17 {
 537                         regulator-min-microvolt = <2920000>;
 538                         regulator-max-microvolt = <3232000>;
 539                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 540                 };
 541
 542                 pp1800_pen:
 543                 pp1800_l18a: ldo18 {
 544                         regulator-min-microvolt = <1800000>;
 545                         regulator-max-microvolt = <1800000>;
 546                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 547                 };
 548
 549                 mcp_vcc:
 550                 pp2850_l19a: ldo19 {
 551                         regulator-min-microvolt = <2960000>;
 552                         regulator-max-microvolt = <2960000>;
 553                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 554                 };
 555         };
 556
 557         regulators-1 {
 558                 compatible = "qcom,pm6150l-rpmh-regulators";
 559                 qcom,pmic-id = "c";
 560
 561                 pp1300_s8c: smps8 {
 562                         regulator-min-microvolt = <1120000>;
 563                         regulator-max-microvolt = <1408000>;
 564                 };
 565
 566                 pp1800_l1c: ldo1 {
 567                         regulator-min-microvolt = <1616000>;
 568                         regulator-max-microvolt = <1984000>;
 569                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 570                 };
 571
 572                 vdd_wcss_adc_dac:
 573                 pp1300_l2c: ldo2 {
 574                         regulator-min-microvolt = <1168000>;
 575                         regulator-max-microvolt = <1304000>;
 576                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 577                 };
 578
 579                 pp1200_brij:
 580                 vdd_ufs1_1p2:
 581                 vdda_csi0_1p25:
 582                 vdda_csi1_1p25:
 583                 vdda_csi2_1p25:
 584                 vdda_csi3_1p25:
 585                 vdda_hv_ebi0:
 586                 vdda_mipi_dsi0_1p2:
 587                 vdda_usb_ss_dp_1p2:
 588                 vddpx_10:
 589                 pp1200_l3c: ldo3 {
 590                         regulator-min-microvolt = <1200000>;
 591                         regulator-max-microvolt = <1200000>;
 592                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 593                 };
 594
 595                 vddpx_2:
 596                 ppvar_l6c: ldo6 {
 597                         regulator-min-microvolt = <1800000>;
 598                         regulator-max-microvolt = <2952000>;
 599                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 600                 };
 601
 602                 pp3300_l7c: ldo7 {
 603                         regulator-min-microvolt = <3304000>;
 604                         regulator-max-microvolt = <3304000>;
 605                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 606                 };
 607
 608                 pp1800_brij_vccio:
 609                 pp1800_edp_vpll:
 610                 pp1800_l8c: ldo8 {
 611                         regulator-min-microvolt = <1800000>;
 612                         regulator-max-microvolt = <1800000>;
 613                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 614                 };
 615
 616                 pp2950_l9c: ldo9 {
 617                         regulator-min-microvolt = <2952000>;
 618                         regulator-max-microvolt = <2952000>;
 619                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 620                 };
 621
 622                 pp3300_l10c: ldo10 {
 623                         regulator-min-microvolt = <3000000>;
 624                         regulator-max-microvolt = <3400000>;
 625                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 626                 };
 627
 628                 pp3300_l11c: ldo11 {
 629                         regulator-min-microvolt = <3000000>;
 630                         regulator-max-microvolt = <3400000>;
 631                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 632                 };
 633
 634                 src_vreg_bob: bob {
 635                         regulator-min-microvolt = <3008000>;
 636                         regulator-max-microvolt = <3960000>;
 637                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 638                 };
 639         };
 640 };
 641
 642 ap_ec_spi: &spi6 {
 643         status = "okay";
 644         cros_ec: ec@0 {
 645                 compatible = "google,cros-ec-spi";
 646                 reg = <0>;
 647                 interrupt-parent = <&tlmm>;
 648                 interrupts = <94 IRQ_TYPE_LEVEL_LOW>;
 649                 pinctrl-names = "default";
 650                 pinctrl-0 = <&ap_ec_int_l>;
 651                 spi-max-frequency = <3000000>;
 652
 653                 cros_ec_pwm: pwm {
 654                         compatible = "google,cros-ec-pwm";
 655                         #pwm-cells = <1>;
 656                 };
 657
 658                 i2c_tunnel: i2c-tunnel {
 659                         compatible = "google,cros-ec-i2c-tunnel";
 660                         google,remote-bus = <0>;
 661                         #address-cells = <1>;
 662                         #size-cells = <0>;
 663                 };
 664
 665                 typec {
 666                         compatible = "google,cros-ec-typec";
 667                         #address-cells = <1>;
 668                         #size-cells = <0>;
 669
 670                         usb_c0: connector@0 {
 671                                 compatible = "usb-c-connector";
 672                                 reg = <0>;
 673                                 label = "left";
 674                                 power-role = "dual";
 675                                 data-role = "host";
 676                                 try-power-role = "source";
 677                         };
 678
 679                         usb_c1: connector@1 {
 680                                 compatible = "usb-c-connector";
 681                                 reg = <1>;
 682                                 label = "right";
 683                                 power-role = "dual";
 684                                 data-role = "host";
 685                                 try-power-role = "source";
 686                         };
 687                 };
 688         };
 689 };
 690
 691 ap_h1_spi: &spi0 {
 692         status = "okay";
 693         cr50: tpm@0 {
 694                 compatible = "google,cr50";
 695                 reg = <0>;
 696                 pinctrl-names = "default";
 697                 pinctrl-0 = <&h1_ap_int_odl>;
 698                 spi-max-frequency = <800000>;
 699                 interrupt-parent = <&tlmm>;
 700                 interrupts = <42 IRQ_TYPE_EDGE_RISING>;
 701         };
 702 };
 703
 704 &camcc {
 705         status = "disabled";
 706 };
 707
 708 ap_sar_sensor_i2c: &i2c5 {
 709         clock-frequency = <400000>;
 710
 711         ap_sar_sensor: proximity@28 {
 712                 compatible = "semtech,sx9310";
 713                 reg = <0x28>;
 714                 #io-channel-cells = <1>;
 715                 pinctrl-names = "default";
 716                 pinctrl-0 = <&p_sensor_int_l>;
 717
 718                 interrupt-parent = <&tlmm>;
 719                 interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
 720
 721                 vdd-supply = <&pp3300_a>;
 722                 svdd-supply = <&pp1800_prox>;
 723
 724                 label = "proximity-wifi";
 725         };
 726 };
 727
 728 ap_tp_i2c: &i2c7 {
 729         clock-frequency = <400000>;
 730
 731         trackpad: trackpad@15 {
 732                 compatible = "elan,ekth3000";
 733                 reg = <0x15>;
 734                 pinctrl-names = "default";
 735                 pinctrl-0 = <&tp_int_odl>;
 736
 737                 interrupt-parent = <&tlmm>;
 738                 interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 739
 740                 vcc-supply = <&pp3300_fp_tp>;
 741
 742                 wakeup-source;
 743         };
 744 };
 745
 746 hp_i2c: &i2c9 {
 747         status = "okay";
 748         clock-frequency = <400000>;
 749 };
 750
 751 &lpasscc {
 752         status = "okay";
 753 };
 754
 755 &lpass_cpu {
 756         status = "okay";
 757
 758         pinctrl-names = "default";
 759         pinctrl-0 = <&sec_mi2s_active>, <&pri_mi2s_active>, <&pri_mi2s_mclk_active>;
 760
 761         #address-cells = <1>;
 762         #size-cells = <0>;
 763
 764         dai-link@0 {
 765                 reg = <MI2S_PRIMARY>;
 766                 qcom,playback-sd-lines = <1>;
 767                 qcom,capture-sd-lines = <0>;
 768         };
 769
 770         secondary_mi2s: dai-link@1 {
 771                 reg = <MI2S_SECONDARY>;
 772                 qcom,playback-sd-lines = <0>;
 773         };
 774
 775         dai-link@5 {
 776                 reg = <LPASS_DP_RX>;
 777         };
 778 };
 779
 780 &lpass_hm {
 781         status = "okay";
 782 };
 783
 784 &mdss {
 785         status = "okay";
 786 };
 787
 788 &mdss_dp {
 789         status = "okay";
 790         pinctrl-names = "default";
 791         pinctrl-0 = <&dp_hot_plug_det>;
 792 };
 793
 794 &mdss_dp_out {
 795         data-lanes = <0 1>;
 796         link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
 797 };
 798
 799 &mdss_dsi0 {
 800         status = "okay";
 801         vdda-supply = <&vdda_mipi_dsi0_1p2>;
 802 };
 803
 804 &mdss_dsi0_out {
 805         data-lanes = <0 1 2 3>;
 806 };
 807
 808 &mdss_dsi0_phy {
 809         status = "okay";
 810         vdds-supply = <&vdda_mipi_dsi0_pll>;
 811 };
 812
 813 &pm6150_adc {
 814         channel@4f {
 815                 reg = <ADC5_AMUX_THM3_100K_PU>;
 816                 qcom,ratiometric;
 817                 qcom,hw-settle-time = <200>;
 818                 label = "charger_therm";
 819         };
 820 };
 821
 822 &pm6150_adc_tm {
 823         status = "okay";
 824
 825         charger-thermistor@0 {
 826                 reg = <0>;
 827                 io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>;
 828                 qcom,ratiometric;
 829                 qcom,hw-settle-time-us = <200>;
 830         };
 831 };
 832
 833 &pm6150_pon {
 834         status = "disabled";
 835 };
 836
 837 &qupv3_id_0 {
 838         status = "okay";
 839 };
 840
 841 &qupv3_id_1 {
 842         status = "okay";
 843 };
 844
 845 &remoteproc_mpss {
 846         status = "okay";
 847         compatible = "qcom,sc7180-mss-pil";
 848         reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>;
 849         reg-names = "qdsp6", "rmb";
 850
 851         clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
 852                  <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>,
 853                  <&gcc GCC_MSS_NAV_AXI_CLK>,
 854                  <&gcc GCC_MSS_SNOC_AXI_CLK>,
 855                  <&gcc GCC_MSS_MFAB_AXIS_CLK>,
 856                  <&rpmhcc RPMH_CXO_CLK>;
 857         clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo";
 858
 859         iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
 860         memory-region = <&mba_mem>, <&mpss_mem>, <&mdata_mem>;
 861
 862         /* This gets overridden for SKUs with LTE support. */
 863         firmware-name = "qcom/sc7180-trogdor/modem-nolte/mba.mbn",
 864                         "qcom/sc7180-trogdor/modem-nolte/qdsp6sw.mbn";
 865
 866         resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
 867                  <&pdc_reset PDC_MODEM_SYNC_RESET>;
 868         reset-names = "mss_restart", "pdc_reset";
 869
 870         qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
 871         qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
 872 };
 873
 874 &scm {
 875         /* TF-A firmware maps memory cached so mark dma-coherent to match. */
 876         dma-coherent;
 877 };
 878
 879 &sdhc_1 {
 880         status = "okay";
 881
 882         pinctrl-names = "default", "sleep";
 883         pinctrl-0 = <&sdc1_on>;
 884         pinctrl-1 = <&sdc1_off>;
 885         vmmc-supply = <&mcp_vcc>;
 886         vqmmc-supply = <&mcp_vccq>;
 887 };
 888
 889 &sdhc_2 {
 890         pinctrl-names = "default", "sleep";
 891         pinctrl-0 = <&sdc2_on>;
 892         pinctrl-1 = <&sdc2_off>;
 893         vmmc-supply = <&pp2950_l9c>;
 894         vqmmc-supply = <&ppvar_l6c>;
 895
 896         cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
 897 };
 898
 899 &spi0 {
 900         pinctrl-0 = <&qup_spi0_spi>, <&qup_spi0_cs_gpio>;
 901         cs-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
 902 };
 903
 904 &spi6 {
 905         pinctrl-0 = <&qup_spi6_spi>, <&qup_spi6_cs_gpio>;
 906         cs-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
 907 };
 908
 909 ap_spi_fp: &spi10 {
 910         pinctrl-0 = <&qup_spi10_spi>, <&qup_spi10_cs_gpio>;
 911         cs-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
 912
 913         cros_ec_fp: ec@0 {
 914                 compatible = "google,cros-ec-fp", "google,cros-ec-spi";
 915                 reg = <0>;
 916                 interrupt-parent = <&tlmm>;
 917                 interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 918                 pinctrl-names = "default";
 919                 pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>;
 920                 boot0-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
 921                 reset-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
 922                 spi-max-frequency = <3000000>;
 923                 vdd-supply = <&pp3300_fp_tp>;
 924         };
 925 };
 926
 927 #include <arm/cros-ec-sbs.dtsi>
 928
 929 &uart3 {
 930         status = "okay";
 931
 932         /delete-property/interrupts;
 933         interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
 934                                 <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
 935
 936         pinctrl-names = "default", "sleep";
 937         pinctrl-1 = <&qup_uart3_sleep>;
 938
 939         bluetooth: bluetooth {
 940                 compatible = "qcom,wcn3991-bt";
 941                 vddio-supply = <&pp1800_l10a>;
 942                 vddxo-supply = <&pp1800_l1c>;
 943                 vddrf-supply = <&pp1300_l2c>;
 944                 vddch0-supply = <&pp3300_l10c>;
 945                 max-speed = <3200000>;
 946         };
 947 };
 948
 949 &uart8 {
 950         status = "okay";
 951 };
 952
 953 &usb_1 {
 954         status = "okay";
 955 };
 956
 957 &usb_1_dwc3 {
 958         dr_mode = "host";
 959         #address-cells = <1>;
 960         #size-cells = <0>;
 961
 962         /* 2.x hub on port 1 */
 963         usb_hub_2_x: hub@1 {
 964                 compatible = "usbbda,5411";
 965                 reg = <1>;
 966                 vdd-supply = <&pp3300_hub>;
 967                 peer-hub = <&usb_hub_3_x>;
 968         };
 969
 970         /* 3.x hub on port 2 */
 971         usb_hub_3_x: hub@2 {
 972                 compatible = "usbbda,411";
 973                 reg = <2>;
 974                 vdd-supply = <&pp3300_hub>;
 975                 peer-hub = <&usb_hub_2_x>;
 976         };
 977 };
 978
 979 &usb_1_hsphy {
 980         status = "okay";
 981         vdd-supply = <&vdd_qusb_hs0_core>;
 982         vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
 983         vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
 984         qcom,imp-res-offset-value = <8>;
 985         qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
 986         qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
 987         qcom,bias-ctrl-value = <0x22>;
 988         qcom,charge-ctrl-value = <3>;
 989         qcom,hsdisc-trim-value = <0>;
 990 };
 991
 992 &usb_1_qmpphy {
 993         status = "okay";
 994         vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
 995         vdda-pll-supply = <&vdda_usb_ss_dp_core>;
 996 };
 997
 998 &venus {
 999         video-firmware {
1000                 iommus = <&apps_smmu 0x0c42 0x0>;
1001         };
1002 };
1003
1004 &wifi {
1005         status = "okay";
1006         vdd-0.8-cx-mx-supply = <&vdd_cx_wlan>;
1007         vdd-1.8-xo-supply = <&pp1800_l1c>;
1008         vdd-1.3-rfa-supply = <&pp1300_l2c>;
1009         vdd-3.3-ch0-supply = <&pp3300_l10c>;
1010         vdd-3.3-ch1-supply = <&pp3300_l11c>;
1011
1012         wifi-firmware {
1013                 iommus = <&apps_smmu 0xc2 0x1>;
1014         };
1015 };
1016
1017 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
1018
1019 &dp_hot_plug_det {
1020         bias-disable;
1021 };
1022
1023 &pri_mi2s_active {
1024         drive-strength = <2>;
1025         bias-pull-down;
1026 };
1027
1028 &pri_mi2s_mclk_active {
1029         drive-strength = <2>;
1030         bias-pull-down;
1031 };
1032
1033 &qspi_cs0 {
1034         bias-disable;           /* External pullup */
1035 };
1036
1037 &qspi_clk {
1038         drive-strength = <8>;
1039         bias-disable;           /* Rely on Cr50 internal pulldown */
1040 };
1041
1042 &qspi_data0 {
1043         bias-disable;           /* Rely on Cr50 internal pulldown */
1044 };
1045
1046 &qspi_data1 {
1047         bias-pull-down;
1048 };
1049
1050 &qup_i2c2_default {
1051         drive-strength = <2>;
1052
1053         /* Has external pullup */
1054         bias-disable;
1055 };
1056
1057 &qup_i2c4_default {
1058         drive-strength = <2>;
1059
1060         /* Has external pullup */
1061         bias-disable;
1062 };
1063
1064 &qup_i2c5_default {
1065         drive-strength = <2>;
1066
1067         /* Has external pullup */
1068         bias-disable;
1069 };
1070
1071 &qup_i2c7_default {
1072         drive-strength = <2>;
1073
1074         /* Has external pullup */
1075         bias-disable;
1076 };
1077
1078 &qup_i2c9_default {
1079         drive-strength = <2>;
1080
1081         /* Has external pullup */
1082         bias-disable;
1083 };
1084
1085 &qup_spi0_spi {
1086         drive-strength = <2>;
1087         bias-disable;
1088 };
1089
1090 &qup_spi0_cs_gpio {
1091         drive-strength = <2>;
1092         bias-disable;
1093 };
1094
1095 &qup_spi6_spi {
1096         drive-strength = <2>;
1097         bias-disable;
1098 };
1099
1100 &qup_spi6_cs_gpio {
1101         drive-strength = <2>;
1102         bias-disable;
1103 };
1104
1105 &qup_spi10_spi {
1106         drive-strength = <2>;
1107         bias-disable;
1108 };
1109
1110 &qup_spi10_cs_gpio {
1111         drive-strength = <2>;
1112         bias-disable;
1113 };
1114
1115 &qup_uart3_cts {
1116         /*
1117          * Configure a pull-down on CTS to match the pull of
1118          * the Bluetooth module.
1119          */
1120         bias-pull-down;
1121 };
1122
1123 &qup_uart3_rts {
1124         /* We'll drive RTS, so no pull */
1125         drive-strength = <2>;
1126         bias-disable;
1127 };
1128
1129 &qup_uart3_tx {
1130         /* We'll drive TX, so no pull */
1131         drive-strength = <2>;
1132         bias-disable;
1133 };
1134
1135 &qup_uart3_rx {
1136         /*
1137          * Configure a pull-up on RX. This is needed to avoid
1138          * garbage data when the TX pin of the Bluetooth module is
1139          * in tri-state (module powered off or not driving the
1140          * signal yet).
1141          */
1142         bias-pull-up;
1143 };
1144
1145 &qup_uart8_tx {
1146         drive-strength = <2>;
1147         bias-disable;
1148 };
1149
1150 &qup_uart8_rx {
1151         drive-strength = <2>;
1152         bias-pull-up;
1153 };
1154
1155 &sec_mi2s_active {
1156         drive-strength = <2>;
1157         bias-pull-down;
1158 };
1159
1160 /* PINCTRL - board-specific pinctrl */
1161
1162 &pm6150_gpios {
1163         status = "disabled"; /* No GPIOs are connected */
1164 };
1165
1166 &pm6150l_gpios {
1167         gpio-line-names = "AP_SUSPEND",
1168                           "",
1169                           "",
1170                           "",
1171                           "",
1172                           "",
1173                           "",
1174                           "",
1175                           "",
1176                           "",
1177                           "",
1178                           "";
1179 };
1180
1181 &tlmm {
1182         /*
1183          * pinctrl settings for pins that have no real owners.
1184          */
1185         pinctrl-names = "default";
1186         pinctrl-0 = <&bios_flash_wp_l>, <&ap_suspend_l_neuter>;
1187
1188         amp_en: amp-en-state {
1189                 pins = "gpio23";
1190                 function = "gpio";
1191                 bias-pull-down;
1192         };
1193
1194         ap_ec_int_l: ap-ec-int-l-state {
1195                 pins = "gpio94";
1196                 function = "gpio";
1197                 bias-pull-up;
1198         };
1199
1200         ap_edp_bklten: ap-edp-bklten-state {
1201                 pins = "gpio12";
1202                 function = "gpio";
1203                 drive-strength = <2>;
1204                 bias-disable;
1205
1206                 /* Force backlight to be disabled to match state at boot. */
1207                 output-low;
1208         };
1209
1210         ap_suspend_l_neuter: ap-suspend-l-neuter-state {
1211                 pins = "gpio27";
1212                 function = "gpio";
1213                 bias-disable;
1214         };
1215
1216         bios_flash_wp_l: bios-flash-wp-l-state {
1217                 pins = "gpio66";
1218                 function = "gpio";
1219                 bias-disable;
1220         };
1221
1222         edp_brij_en: edp-brij-en-state {
1223                 pins = "gpio104";
1224                 function = "gpio";
1225                 drive-strength = <2>;
1226                 bias-disable;
1227         };
1228
1229         en_pp3300_codec: en-pp3300-codec-state {
1230                 pins = "gpio83";
1231                 function = "gpio";
1232                 drive-strength = <2>;
1233                 bias-disable;
1234         };
1235
1236         en_pp3300_dx_edp: en-pp3300-dx-edp-state {
1237                 pins = "gpio30";
1238                 function = "gpio";
1239                 drive-strength = <2>;
1240                 bias-disable;
1241         };
1242
1243         en_pp3300_hub: en-pp3300-hub-state {
1244                 pins = "gpio84";
1245                 function = "gpio";
1246                 drive-strength = <2>;
1247                 bias-disable;
1248         };
1249
1250         fp_rst_l: fp-rst-l-state {
1251                 pins = "gpio22";
1252                 function = "gpio";
1253                 bias-disable;
1254                 drive-strength = <2>;
1255         };
1256
1257         fp_to_ap_irq_l: fp-to-ap-irq-l-state {
1258                 pins = "gpio4";
1259                 function = "gpio";
1260
1261                 /* Has external pullup */
1262                 bias-disable;
1263         };
1264
1265         fpmcu_boot0: fpmcu-boot0-state {
1266                 pins = "gpio10";
1267                 function = "gpio";
1268                 bias-disable;
1269         };
1270
1271         h1_ap_int_odl: h1-ap-int-odl-state {
1272                 pins = "gpio42";
1273                 function = "gpio";
1274                 bias-pull-up;
1275         };
1276
1277         hp_irq: hp-irq-state {
1278                 pins = "gpio28";
1279                 function = "gpio";
1280                 bias-pull-up;
1281         };
1282
1283         pen_irq_l: pen-irq-l-state {
1284                 pins = "gpio21";
1285                 function = "gpio";
1286
1287                 /* Has external pullup */
1288                 bias-disable;
1289         };
1290
1291         pen_pdct_l: pen-pdct-l-state-state {
1292                 pins = "gpio52";
1293                 function = "gpio";
1294
1295                 /* Has external pullup */
1296                 bias-disable;
1297         };
1298
1299         pen_rst_odl: pen-rst-odl-state {
1300                 pins = "gpio18";
1301                 function = "gpio";
1302                 bias-disable;
1303                 drive-strength = <2>;
1304
1305                 /*
1306                  * The pen driver doesn't currently support
1307                  * driving this reset line.  By specifying
1308                  * output-high here we're relying on the fact
1309                  * that this pin has a default pulldown at boot
1310                  * (which makes sure the pen was in reset if it
1311                  * was powered) and then we set it high here to
1312                  * take it out of reset.  Better would be if the
1313                  * pen driver could control this and we could
1314                  * remove "output-high" here.
1315                  */
1316                 output-high; /* TODO: Remove this? */
1317         };
1318
1319         p_sensor_int_l: p-sensor-int-l-state {
1320                 pins = "gpio24";
1321                 function = "gpio";
1322
1323                 /* Has external pullup */
1324                 bias-disable;
1325         };
1326
1327         qspi_sleep: qspi-sleep-state {
1328                 pins = "gpio63", "gpio64", "gpio65", "gpio68";
1329
1330                 /*
1331                  * When we're not actively transferring we want pins as GPIOs
1332                  * with output disabled so that the quad SPI IP block stops
1333                  * driving them. We rely on the normal pulls configured in
1334                  * the active state and don't redefine them here. Also note
1335                  * that we don't need the reverse (output-enable) in the
1336                  * normal mode since the "output-enable" only matters for
1337                  * GPIO function.
1338                  */
1339                 function = "gpio";
1340                 output-disable;
1341         };
1342
1343         qup_uart3_sleep: qup-uart3-sleep-state {
1344                 cts-pins {
1345                         /*
1346                          * Configure a pull-down on CTS to match the pull of
1347                          * the Bluetooth module.
1348                          */
1349                         pins = "gpio38";
1350                         function = "gpio";
1351                         bias-pull-down;
1352                 };
1353
1354                 rts-pins {
1355                         /*
1356                          * Configure pull-down on RTS. As RTS is active low
1357                          * signal, pull it low to indicate the BT SoC that it
1358                          * can wakeup the system anytime from suspend state by
1359                          * pulling RX low (by sending wakeup bytes).
1360                          */
1361                         pins = "gpio39";
1362                         function = "gpio";
1363                         bias-pull-down;
1364                 };
1365
1366                 tx-pins {
1367                         /*
1368                          * Configure pull-up on TX when it isn't actively driven
1369                          * to prevent BT SoC from receiving garbage during sleep.
1370                          */
1371                         pins = "gpio40";
1372                         function = "gpio";
1373                         bias-pull-up;
1374                 };
1375
1376                 rx-pins {
1377                         /*
1378                          * Configure a pull-up on RX. This is needed to avoid
1379                          * garbage data when the TX pin of the Bluetooth module
1380                          * is floating which may cause spurious wakeups.
1381                          */
1382                         pins = "gpio41";
1383                         function = "gpio";
1384                         bias-pull-up;
1385                 };
1386         };
1387
1388         /* Named trackpad_int_1v8_odl on earlier revision schematics */
1389         trackpad_int_1v8_odl:
1390         tp_int_odl: tp-int-odl-state {
1391                 pins = "gpio0";
1392                 function = "gpio";
1393
1394                 /* Has external pullup */
1395                 bias-disable;
1396         };
1397
1398         ts_int_l: ts-int-l-state {
1399                 pins = "gpio9";
1400                 function = "gpio";
1401                 bias-pull-up;
1402         };
1403
1404         ts_reset_l: ts-reset-l-state {
1405                 pins = "gpio8";
1406                 function = "gpio";
1407                 bias-disable;
1408
1409                 /*
1410                  * The reset GPIO to the touchscreen takes almost 2ms to drop
1411                  * at the default drive strength. When we bump it up to 8mA it
1412                  * falls in under 500us. We want this to be fast since the Elan
1413                  * datasheet (and any drivers written based on it) talk about using
1414                  * a 500 us reset pulse.
1415                  */
1416                 drive-strength = <8>;
1417         };
1418
1419         sdc1_on: sdc1-on-state {
1420                 clk-pins {
1421                         pins = "sdc1_clk";
1422                         bias-disable;
1423                         drive-strength = <16>;
1424                 };
1425
1426                 cmd-pins {
1427                         pins = "sdc1_cmd";
1428                         bias-pull-up;
1429                         drive-strength = <16>;
1430                 };
1431
1432                 data-pins {
1433                         pins = "sdc1_data";
1434                         bias-pull-up;
1435                         drive-strength = <16>;
1436                 };
1437
1438                 rclk-pins {
1439                         pins = "sdc1_rclk";
1440                         bias-pull-down;
1441                 };
1442         };
1443
1444         sdc1_off: sdc1-off-state {
1445                 clk-pins {
1446                         pins = "sdc1_clk";
1447                         bias-disable;
1448                         drive-strength = <2>;
1449                 };
1450
1451                 cmd-pins {
1452                         pins = "sdc1_cmd";
1453                         bias-pull-up;
1454                         drive-strength = <2>;
1455                 };
1456
1457                 data-pins {
1458                         pins = "sdc1_data";
1459                         bias-pull-up;
1460                         drive-strength = <2>;
1461                 };
1462
1463                 rclk-pins {
1464                         pins = "sdc1_rclk";
1465                         bias-pull-down;
1466                 };
1467         };
1468
1469         sdc2_on: sdc2-on-state {
1470                 clk-pins {
1471                         pins = "sdc2_clk";
1472                         bias-disable;
1473                         drive-strength = <16>;
1474                 };
1475
1476                 cmd-pins {
1477                         pins = "sdc2_cmd";
1478                         bias-pull-up;
1479                         drive-strength = <10>;
1480                 };
1481
1482                 data-pins {
1483                         pins = "sdc2_data";
1484                         bias-pull-up;
1485                         drive-strength = <10>;
1486                 };
1487
1488                 sd-cd-pins {
1489                         pins = "gpio69";
1490                         function = "gpio";
1491                         bias-pull-up;
1492                         drive-strength = <2>;
1493                 };
1494         };
1495
1496         sdc2_off: sdc2-off-state {
1497                 clk-pins {
1498                         pins = "sdc2_clk";
1499                         bias-disable;
1500                         drive-strength = <2>;
1501                 };
1502
1503                 cmd-pins {
1504                         pins = "sdc2_cmd";
1505                         bias-pull-up;
1506                         drive-strength = <2>;
1507                 };
1508
1509                 data-pins {
1510                         pins = "sdc2_data";
1511                         bias-pull-up;
1512                         drive-strength = <2>;
1513                 };
1514
1515                 sd-cd-pins {
1516                         pins = "gpio69";
1517                         function = "gpio";
1518                         bias-pull-up;
1519                         drive-strength = <2>;
1520                 };
1521         };
1522
1523         uf_cam_en: uf-cam-en-state {
1524                 pins = "gpio6";
1525                 function = "gpio";
1526                 drive-strength = <2>;
1527
1528                 /* External pull down */
1529                 bias-disable;
1530         };
1531
1532         wf_cam_en: wf-cam-en-state {
1533                 pins = "gpio7";
1534                 function = "gpio";
1535                 drive-strength = <2>;
1536
1537                 /* External pull down */
1538                 bias-disable;
1539         };
1540 };