src/arm64/qcom/sc8180x-primus.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
   4  * Copyright (c) 2020-2023, Linaro Limited
   5  */
   6
   7 /dts-v1/;
   8
   9 #include <dt-bindings/firmware/qcom,scm.h>
  10 #include <dt-bindings/gpio/gpio.h>
  11 #include <dt-bindings/input/gpio-keys.h>
  12 #include <dt-bindings/input/input.h>
  13 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  14 #include "sc8180x.dtsi"
  15 #include "sc8180x-pmics.dtsi"
  16
  17 / {
  18         model = "Qualcomm SC8180x Primus";
  19         compatible = "qcom,sc8180x-primus", "qcom,sc8180x";
  20
  21         aliases {
  22                 serial0 = &uart12;
  23                 serial1 = &uart13;
  24         };
  25
  26         backlight: backlight {
  27                 compatible = "pwm-backlight";
  28                 pwms = <&pmc8180c_lpg 4 1000000>;
  29                 enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>;
  30
  31                 pinctrl-names = "default";
  32                 pinctrl-0 = <&bl_pwm_default>;
  33         };
  34
  35         chosen {
  36                 stdout-path = "serial0:115200n8";
  37         };
  38
  39         gpio-keys {
  40                 compatible = "gpio-keys";
  41
  42                 pinctrl-names = "default";
  43                 pinctrl-0 = <&hall_int_active_state>;
  44
  45                 lid-switch {
  46                         gpios = <&tlmm 121 GPIO_ACTIVE_LOW>;
  47                         linux,input-type = <EV_SW>;
  48                         linux,code = <SW_LID>;
  49                         wakeup-source;
  50                         wakeup-event-action = <EV_ACT_DEASSERTED>;
  51                 };
  52         };
  53
  54         pmic-glink {
  55                 compatible = "qcom,sc8180x-pmic-glink", "qcom,pmic-glink";
  56
  57                 #address-cells = <1>;
  58                 #size-cells = <0>;
  59
  60                 connector@0 {
  61                         compatible = "usb-c-connector";
  62                         reg = <0>;
  63                         power-role = "dual";
  64                         data-role = "dual";
  65
  66                         ports {
  67                                 #address-cells = <1>;
  68                                 #size-cells = <0>;
  69
  70                                 port@0 {
  71                                         reg = <0>;
  72
  73                                         pmic_glink_con0_hs: endpoint {
  74                                                 remote-endpoint = <&usb_prim_role_switch>;
  75                                         };
  76                                 };
  77
  78                                 port@1 {
  79                                         reg = <1>;
  80
  81                                         pmic_glink_con0_ss: endpoint {
  82                                                 remote-endpoint = <&usb_prim_qmpphy_out>;
  83                                         };
  84                                 };
  85
  86                                 port@2 {
  87                                         reg = <2>;
  88
  89                                         pmic_glink_con0_sbu: endpoint {
  90                                                 remote-endpoint = <&usbprim_sbu_mux>;
  91                                         };
  92                                 };
  93                         };
  94                 };
  95
  96                 connector@1 {
  97                         compatible = "usb-c-connector";
  98                         reg = <1>;
  99                         power-role = "dual";
 100                         data-role = "dual";
 101
 102                         ports {
 103                                 #address-cells = <1>;
 104                                 #size-cells = <0>;
 105                                 port@0 {
 106                                         reg = <0>;
 107
 108                                         pmic_glink_con1_hs: endpoint {
 109                                                 remote-endpoint = <&usb_sec_role_switch>;
 110                                         };
 111                                 };
 112
 113                                 port@1 {
 114                                         reg = <1>;
 115
 116                                         pmic_glink_con1_ss: endpoint {
 117                                                 remote-endpoint = <&usb_sec_qmpphy_out>;
 118                                         };
 119                                 };
 120
 121                                 port@2 {
 122                                         reg = <2>;
 123
 124                                         pmic_glink_con1_sbu: endpoint {
 125                                                 remote-endpoint = <&usbsec_sbu_mux>;
 126                                         };
 127                                 };
 128                         };
 129                 };
 130         };
 131
 132         reserved-memory {
 133                 rmtfs_mem: rmtfs-region@85500000 {
 134                         compatible = "qcom,rmtfs-mem";
 135                         reg = <0x0 0x85500000 0x0 0x200000>;
 136                         no-map;
 137
 138                         qcom,client-id = <1>;
 139                         qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
 140                 };
 141
 142                 wlan_mem: wlan-region@8bc00000 {
 143                         reg = <0x0 0x8bc00000 0x0 0x180000>;
 144                         no-map;
 145                 };
 146
 147                 adsp_mem: adsp-region@96e00000 {
 148                         reg = <0x0 0x96e00000 0x0 0x1c00000>;
 149                         no-map;
 150                 };
 151
 152                 mpss_mem: mpss-region@8d800000 {
 153                         reg = <0x0 0x8d800000 0x0 0x9600000>;
 154                         no-map;
 155                 };
 156
 157                 gpu_mem: gpu-region@98a00000 {
 158                         reg = <0x0 0x98a00000 0x0 0x2000>;
 159                         no-map;
 160                 };
 161
 162                 reserved-region@9a500000 {
 163                         reg = <0x0 0x9a500000 0x0 0x600000>;
 164                         no-map;
 165                 };
 166         };
 167
 168         vreg_nvme_0p9: nvme-0p9-regulator {
 169                 compatible = "regulator-fixed";
 170                 regulator-name = "vreg_nvme_0p9";
 171
 172                 regulator-min-microvolt = <900000>;
 173                 regulator-max-microvolt = <900000>;
 174
 175                 regulator-always-on;
 176         };
 177
 178         vreg_nvme_3p3: nvme-3p3-regulator {
 179                 compatible = "regulator-fixed";
 180                 regulator-name = "vreg_nvme_3p3";
 181
 182                 regulator-min-microvolt = <3300000>;
 183                 regulator-max-microvolt = <3300000>;
 184
 185                 gpio = <&pmc8180c_gpios 11 0>;
 186                 enable-active-high;
 187
 188                 regulator-always-on;
 189         };
 190
 191         vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator {
 192                 compatible = "regulator-fixed";
 193                 regulator-name = "vdd_kb_tp_3v3";
 194                 regulator-min-microvolt = <3300000>;
 195                 regulator-max-microvolt = <3300000>;
 196
 197                 gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>;
 198                 enable-active-high;
 199
 200                 regulator-always-on;
 201
 202                 pinctrl-names = "default";
 203                 pinctrl-0 = <&kb_tp_3v3_en_active_state>;
 204         };
 205
 206         vph_pwr: vph-pwr-regulator {
 207                 compatible = "regulator-fixed";
 208                 regulator-name = "vph_pwr";
 209                 regulator-min-microvolt = <3700000>;
 210                 regulator-max-microvolt = <3700000>;
 211         };
 212
 213         vreg_s4a_1p8: pm8150-s4 {
 214                 compatible = "regulator-fixed";
 215                 regulator-name = "vreg_s4a_1p8";
 216
 217                 regulator-min-microvolt = <1800000>;
 218                 regulator-max-microvolt = <1800000>;
 219
 220                 regulator-always-on;
 221                 regulator-boot-on;
 222
 223                 vin-supply = <&vph_pwr>;
 224         };
 225
 226         usbprim-sbu-mux {
 227                 compatible = "pericom,pi3usb102", "gpio-sbu-mux";
 228
 229                 enable-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
 230                 select-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
 231
 232                 pinctrl-names = "default";
 233                 pinctrl-0 = <&usbprim_sbu_default>;
 234
 235                 mode-switch;
 236                 orientation-switch;
 237
 238                 port {
 239                         usbprim_sbu_mux: endpoint {
 240                                 remote-endpoint = <&pmic_glink_con0_sbu>;
 241                         };
 242                 };
 243         };
 244
 245         usbsec-sbu-mux {
 246                 compatible = "pericom,pi3usb102", "gpio-sbu-mux";
 247
 248                 enable-gpios = <&tlmm 188 GPIO_ACTIVE_LOW>;
 249                 select-gpios = <&tlmm 187 GPIO_ACTIVE_HIGH>;
 250
 251                 pinctrl-names = "default";
 252                 pinctrl-0 = <&usbsec_sbu_default>;
 253
 254                 mode-switch;
 255                 orientation-switch;
 256
 257                 port {
 258                         usbsec_sbu_mux: endpoint {
 259                                 remote-endpoint = <&pmic_glink_con1_sbu>;
 260                         };
 261                 };
 262         };
 263 };
 264
 265 &apps_rsc {
 266         regulators-0 {
 267                 compatible = "qcom,pmc8180-rpmh-regulators";
 268                 qcom,pmic-id = "a";
 269
 270                 vdd-s5-supply = <&vph_pwr>;
 271                 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>;
 272
 273                 vreg_s5a_2p0: smps5 {
 274                         regulator-min-microvolt = <2040000>;
 275                         regulator-max-microvolt = <2100000>;
 276                 };
 277
 278                 vreg_l7a_1p8: ldo7 {
 279                         regulator-min-microvolt = <1800000>;
 280                         regulator-max-microvolt = <1800000>;
 281                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 282                 };
 283
 284                 vreg_l9a_1p3: ldo9 {
 285                         regulator-min-microvolt = <1296000>;
 286                         regulator-max-microvolt = <1304000>;
 287                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 288                 };
 289
 290                 vreg_l12a_1p8: ldo12 {
 291                         regulator-min-microvolt = <1800000>;
 292                         regulator-max-microvolt = <1800000>;
 293                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 294                 };
 295         };
 296
 297         regulators-1 {
 298                 compatible = "qcom,pmc8180c-rpmh-regulators";
 299                 qcom,pmic-id = "c";
 300
 301                 vdd-s6-supply = <&vph_pwr>;
 302                 vdd-s8-supply = <&vph_pwr>;
 303                 vdd-l2-l3-supply = <&vreg_s6c_1p35>;
 304                 vdd-bob-supply = <&vph_pwr>;
 305
 306                 vreg_s6c_1p35: smps6 {
 307                         regulator-min-microvolt = <1350000>;
 308                         regulator-max-microvolt = <1372000>;
 309                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 310                 };
 311
 312                 vreg_s8c_1p8: smps8 {
 313                         regulator-min-microvolt = <1800000>;
 314                         regulator-max-microvolt = <1800000>;
 315                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 316                         regulator-always-on;
 317                 };
 318
 319                 vreg_l3c_1p2: ldo3 {
 320                         regulator-min-microvolt = <1200000>;
 321                         regulator-max-microvolt = <1200000>;
 322                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 323                 };
 324
 325                 vreg_l4c_3p3: ldo4 {
 326                         regulator-min-microvolt = <3008000>;
 327                         regulator-max-microvolt = <3008000>;
 328                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 329                 };
 330
 331                 vreg_l10c_3p3: ldo10 {
 332                         regulator-min-microvolt = <3000000>;
 333                         regulator-max-microvolt = <3312000>;
 334                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 335                 };
 336
 337                 vreg_l11c_3p3: ldo11 {
 338                         regulator-min-microvolt = <3296000>;
 339                         regulator-max-microvolt = <3304000>;
 340                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 341                 };
 342
 343                 vreg_bob: bob {
 344                         regulator-min-microvolt = <3296000>;
 345                         regulator-max-microvolt = <3350000>;
 346                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 347                 };
 348         };
 349
 350         regulators-2 {
 351                 compatible = "qcom,pmc8180-rpmh-regulators";
 352                 qcom,pmic-id = "e";
 353
 354                 vdd-s4-supply = <&vph_pwr>;
 355                 vdd-s5-supply = <&vph_pwr>;
 356                 vdd-l2-l10-supply = <&vreg_bob>;
 357                 vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>;
 358                 vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>;
 359                 vdd-l13-l16-l17-supply = <&vreg_bob>;
 360
 361                 vreg_s4e_0p98: smps4 {
 362                         regulator-min-microvolt = <992000>;
 363                         regulator-max-microvolt = <992000>;
 364                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 365                 };
 366
 367                 vreg_s5e_2p05: smps5 {
 368                         regulator-min-microvolt = <2040000>;
 369                         regulator-max-microvolt = <2040000>;
 370                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 371                 };
 372
 373                 vreg_l1e_0p75: ldo1 {
 374                         regulator-min-microvolt = <752000>;
 375                         regulator-max-microvolt = <752000>;
 376                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 377                 };
 378
 379                 vreg_l5e_0p88: ldo5 {
 380                         regulator-min-microvolt = <880000>;
 381                         regulator-max-microvolt = <880000>;
 382                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 383                 };
 384
 385                 vreg_l7e_1p8: ldo7 {
 386                         regulator-min-microvolt = <1800000>;
 387                         regulator-max-microvolt = <1800000>;
 388                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 389                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 390                                                    RPMH_REGULATOR_MODE_HPM>;
 391                         regulator-allow-set-load;
 392                 };
 393
 394                 vreg_l10e_2p9: ldo10 {
 395                         regulator-min-microvolt = <2904000>;
 396                         regulator-max-microvolt = <2904000>;
 397                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 398                         regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
 399                                                    RPMH_REGULATOR_MODE_HPM>;
 400                         regulator-allow-set-load;
 401                 };
 402
 403                 vreg_l12e: ldo12 {
 404                         regulator-min-microvolt = <1800000>;
 405                         regulator-max-microvolt = <1800000>;
 406                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 407                 };
 408
 409                 vreg_l16e_3p0: ldo16 {
 410                         regulator-min-microvolt = <3072000>;
 411                         regulator-max-microvolt = <3072000>;
 412                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 413                 };
 414         };
 415 };
 416
 417 &gpu {
 418         status = "okay";
 419
 420         zap-shader {
 421                 memory-region = <&gpu_mem>;
 422                 firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn";
 423         };
 424 };
 425
 426 &i2c1 {
 427         clock-frequency = <100000>;
 428
 429         pinctrl-names = "default";
 430         pinctrl-0 = <&ts_i2c_active_state>;
 431
 432         status = "okay";
 433
 434         touchscreen@10 {
 435                 compatible = "hid-over-i2c";
 436                 reg = <0x10>;
 437                 hid-descr-addr = <0x1>;
 438
 439                 vdd-supply = <&vreg_l4c_3p3>;
 440                 vddl-supply = <&vreg_l12e>;
 441
 442                 post-power-on-delay-ms = <20>;
 443
 444                 interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>;
 445
 446                 pinctrl-names = "default";
 447                 pinctrl-0 = <&ts_active_state>;
 448         };
 449 };
 450
 451 &i2c7 {
 452         clock-frequency = <100000>;
 453
 454         pinctrl-names = "default";
 455         pinctrl-0 = <&aux_i2c_active_state>;
 456
 457         status = "okay";
 458
 459         touchpad@15 {
 460                 compatible = "hid-over-i2c";
 461                 reg = <0x15>;
 462                 hid-descr-addr = <0x1>;
 463
 464                 interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>;
 465
 466                 pinctrl-names = "default";
 467                 pinctrl-0 = <&tp_int_active_state>;
 468
 469                 vdd-supply = <&vdd_kb_tp_3v3>;
 470         };
 471
 472         keyboard@3a {
 473                 compatible = "hid-over-i2c";
 474                 reg = <0x3a>;
 475                 hid-descr-addr = <0x1>;
 476                 interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>;
 477
 478                 pinctrl-names = "default";
 479                 pinctrl-0 = <&kb_int_active_state>;
 480
 481                 vdd-supply = <&vdd_kb_tp_3v3>;
 482         };
 483 };
 484
 485 &mdss {
 486         status = "okay";
 487 };
 488
 489 &mdss_dp0 {
 490         status = "okay";
 491 };
 492
 493 &mdss_dp0_out {
 494         data-lanes = <0 1>;
 495         remote-endpoint = <&usb_prim_qmpphy_dp_in>;
 496 };
 497
 498 &mdss_dp1 {
 499         status = "okay";
 500 };
 501
 502 &mdss_dp1_out {
 503         data-lanes = <0 1>;
 504         remote-endpoint = <&usb_sec_qmpphy_dp_in>;
 505 };
 506
 507 &mdss_edp {
 508         data-lanes = <0 1 2 3>;
 509
 510         pinctrl-names = "default";
 511         pinctrl-0 = <&edp_hpd_active>;
 512
 513         status = "okay";
 514
 515         aux-bus {
 516                 panel {
 517                         compatible = "edp-panel";
 518
 519                         backlight = <&backlight>;
 520
 521                         port {
 522                                 auo_b133han05_in: endpoint {
 523                                         remote-endpoint = <&mdss_edp_out>;
 524                                 };
 525                         };
 526                 };
 527         };
 528
 529         ports {
 530                 port@1 {
 531                         reg = <1>;
 532                         mdss_edp_out: endpoint {
 533                                 remote-endpoint = <&auo_b133han05_in>;
 534                         };
 535                 };
 536         };
 537 };
 538
 539 &pcie1 {
 540         perst-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
 541         wake-gpios = <&tlmm 177 GPIO_ACTIVE_HIGH>;
 542         pinctrl-names = "default";
 543         pinctrl-0 = <&pcie2_default_state>;
 544
 545         status = "okay";
 546 };
 547
 548 &pcie1_phy {
 549         vdda-phy-supply = <&vreg_l5e_0p88>;
 550         vdda-pll-supply = <&vreg_l3c_1p2>;
 551
 552         status = "okay";
 553 };
 554
 555 &pmc8180c_lpg {
 556         status = "okay";
 557 };
 558
 559 &qupv3_id_0 {
 560         status = "okay";
 561 };
 562
 563 &qupv3_id_1 {
 564         status = "okay";
 565 };
 566
 567 &qupv3_id_2 {
 568         status = "okay";
 569 };
 570
 571 &remoteproc_adsp {
 572         memory-region = <&adsp_mem>;
 573         firmware-name = "qcom/sc8180x/qcadsp8180.mbn";
 574
 575         status = "okay";
 576 };
 577
 578 &remoteproc_mpss {
 579         memory-region = <&mpss_mem>;
 580         firmware-name = "qcom/sc8180x/qcmpss8180.mbn";
 581
 582         status = "okay";
 583 };
 584
 585 &uart12 {
 586         compatible = "qcom,geni-debug-uart";
 587         status = "okay";
 588 };
 589
 590 &uart13 {
 591         pinctrl-names = "default";
 592         pinctrl-0 = <&uart13_state>;
 593
 594         status = "okay";
 595
 596         bluetooth {
 597                 compatible = "qcom,wcn3998-bt";
 598
 599                 vddio-supply = <&vreg_s4a_1p8>;
 600                 vddxo-supply = <&vreg_l7a_1p8>;
 601                 vddrf-supply = <&vreg_l9a_1p3>;
 602                 vddch0-supply = <&vreg_l11c_3p3>;
 603                 max-speed = <3200000>;
 604         };
 605 };
 606
 607 &ufs_mem_hc {
 608         reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>;
 609
 610         vcc-supply = <&vreg_l10e_2p9>;
 611         vcc-max-microamp = <155000>;
 612
 613         vccq2-supply = <&vreg_l7e_1p8>;
 614         vccq2-max-microamp = <425000>;
 615
 616         status = "okay";
 617 };
 618
 619 &ufs_mem_phy {
 620         vdda-phy-supply = <&vreg_l5e_0p88>;
 621         vdda-pll-supply = <&vreg_l3c_1p2>;
 622
 623         status = "okay";
 624 };
 625
 626 &usb_prim_hsphy {
 627         vdda-pll-supply = <&vreg_l5e_0p88>;
 628         vdda18-supply = <&vreg_l12a_1p8>;
 629         vdda33-supply = <&vreg_l16e_3p0>;
 630
 631         status = "okay";
 632 };
 633
 634 &usb_prim_qmpphy {
 635         vdda-phy-supply = <&vreg_l3c_1p2>;
 636         vdda-pll-supply = <&vreg_l5e_0p88>;
 637
 638         orientation-switch;
 639
 640         status = "okay";
 641 };
 642
 643 &usb_prim {
 644         status = "okay";
 645 };
 646
 647 &usb_prim_dwc3 {
 648         dr_mode = "host";
 649 };
 650
 651 &usb_prim_qmpphy_dp_in {
 652         remote-endpoint = <&mdss_dp0_out>;
 653 };
 654
 655 &usb_prim_qmpphy_out {
 656         remote-endpoint = <&pmic_glink_con0_ss>;
 657 };
 658
 659 &usb_prim_role_switch {
 660         remote-endpoint = <&pmic_glink_con0_hs>;
 661 };
 662
 663 &usb_sec_hsphy {
 664         vdda-pll-supply = <&vreg_l5e_0p88>;
 665         vdda18-supply = <&vreg_l12a_1p8>;
 666         vdda33-supply = <&vreg_l16e_3p0>;
 667
 668         status = "okay";
 669 };
 670
 671 &usb_sec_qmpphy {
 672         vdda-phy-supply = <&vreg_l3c_1p2>;
 673         vdda-pll-supply = <&vreg_l5e_0p88>;
 674
 675         orientation-switch;
 676
 677         status = "okay";
 678 };
 679
 680 &usb_sec_qmpphy_dp_in {
 681         remote-endpoint = <&mdss_dp1_out>;
 682 };
 683
 684 &usb_sec_qmpphy_out {
 685         remote-endpoint = <&pmic_glink_con1_ss>;
 686 };
 687
 688 &usb_sec_role_switch {
 689         remote-endpoint = <&pmic_glink_con1_hs>;
 690 };
 691
 692 &usb_sec {
 693         status = "okay";
 694 };
 695
 696 &usb_sec_dwc3 {
 697         dr_mode = "host";
 698 };
 699
 700 &wifi {
 701         memory-region = <&wlan_mem>;
 702
 703         vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>;
 704         vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 705         vdd-1.3-rfa-supply = <&vreg_l9a_1p3>;
 706         vdd-3.3-ch0-supply = <&vreg_l11c_3p3>;
 707         vdd-3.3-ch1-supply = <&vreg_l10c_3p3>;
 708
 709         status = "okay";
 710 };
 711
 712 &xo_board_clk {
 713         clock-frequency = <38400000>;
 714 };
 715
 716 /* PINCTRL */
 717
 718 &pmc8180c_gpios {
 719         bl_pwm_default: bl-pwm-default-state {
 720                 en-pins {
 721                         pins = "gpio8";
 722                         function = "normal";
 723                 };
 724
 725                 pwm-pins {
 726                         pins = "gpio10";
 727                         function = "func1";
 728                 };
 729         };
 730 };
 731
 732 &tlmm {
 733         gpio-reserved-ranges = <0 4>, <47 4>, <126 4>;
 734
 735         aux_i2c_active_state: aux-i2c-active-state {
 736                 pins = "gpio98", "gpio99";
 737                 function = "qup7";
 738
 739                 bias-disable;
 740                 drive-strength = <16>;
 741         };
 742
 743         edp_hpd_active: epd-hpd-active-state {
 744                 pins = "gpio10";
 745                 function = "edp_hot";
 746         };
 747
 748         hall_int_active_state: hall-int-active-state {
 749                 pins = "gpio121";
 750                 function = "gpio";
 751
 752                 bias-disable;
 753         };
 754
 755         kb_int_active_state: kb-int-active-state {
 756                 int-n-pins {
 757                         pins = "gpio37";
 758                         function = "gpio";
 759
 760                         bias-pull-up;
 761                 };
 762
 763                 kp-disable-pins {
 764                         pins = "gpio135";
 765                         function = "gpio";
 766
 767                         output-high;
 768                 };
 769         };
 770
 771         kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state {
 772                 pins = "gpio4";
 773                 function = "gpio";
 774
 775                 bias-disable;
 776         };
 777
 778         pcie2_default_state: pcie2-default-state {
 779                 clkreq-pins {
 780                         pins = "gpio176";
 781                         function = "pci_e2";
 782                         bias-pull-up;
 783                 };
 784
 785                 reset-n-pins {
 786                         pins = "gpio175";
 787                         function = "gpio";
 788
 789                         drive-strength = <2>;
 790                         output-low;
 791                         bias-pull-down;
 792                 };
 793
 794                 wake-n-pins {
 795                         pins = "gpio177";
 796                         function = "gpio";
 797
 798                         drive-strength = <2>;
 799                         bias-pull-up;
 800                 };
 801         };
 802
 803         usbprim_sbu_default: usbprim-sbu-state {
 804                 oe-n-pins {
 805                         pins = "gpio152";
 806                         function = "gpio";
 807                         bias-disable;
 808                         drive-strength = <16>;
 809                         output-high;
 810                 };
 811
 812                 sel-pins {
 813                         pins = "gpio100";
 814                         function = "gpio";
 815                         bias-disable;
 816                         drive-strength = <16>;
 817                 };
 818         };
 819
 820         usbsec_sbu_default: usbsec-sbu-state {
 821                 oe-n-pins {
 822                         pins = "gpio188";
 823                         function = "gpio";
 824                         bias-disable;
 825                         drive-strength = <16>;
 826                         output-high;
 827                 };
 828
 829                 sel-pins {
 830                         pins = "gpio187";
 831                         function = "gpio";
 832                         bias-disable;
 833                         drive-strength = <16>;
 834                 };
 835         };
 836
 837         tp_int_active_state: tp-int-active-state {
 838                 tp-int-pins {
 839                         pins = "gpio24";
 840                         function = "gpio";
 841
 842                         bias-disable;
 843                 };
 844
 845                 tp-close-n-pins {
 846                         pins = "gpio116";
 847                         function = "gpio";
 848
 849                         bias-disable;
 850                 };
 851         };
 852
 853         ts_active_state: ts-active-state {
 854                 int-n-pins {
 855                         pins = "gpio122";
 856                         function = "gpio";
 857
 858                         bias-disable;
 859                 };
 860
 861                 reset-n-pins {
 862                         pins = "gpio54";
 863                         function = "gpio";
 864
 865                         output-high;
 866                 };
 867         };
 868
 869         ts_i2c_active_state: ts-i2c-active-state {
 870                 pins = "gpio114", "gpio115";
 871                 function = "qup1";
 872
 873                 /* External pull up */
 874                 bias-disable;
 875                 drive-strength = <2>;
 876         };
 877
 878         uart13_state: uart13-state {
 879                 cts-pins {
 880                         pins = "gpio43";
 881                         function = "qup13";
 882                         bias-pull-down;
 883                 };
 884
 885                 rts-tx-pins {
 886                         pins = "gpio44", "gpio45";
 887                         function = "qup13";
 888                         drive-strength = <2>;
 889                         bias-disable;
 890                 };
 891
 892                 rx-pins {
 893                         pins = "gpio46";
 894                         function = "qup13";
 895                         bias-pull-up;
 896                 };
 897         };
 898 };