src/arm64/xilinx/zynqmp-sck-kv-g-revA.dtso

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * dts file for KV260 revA Carrier Card
   4  *
   5  * (C) Copyright 2020 - 2022, Xilinx, Inc.
   6  * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
   7  *
   8  * SD level shifter:
   9  * "A" - A01 board un-modified (NXP)
  10  * "Y" - A01 board modified with legacy interposer (Nexperia)
  11  * "Z" - A01 board modified with Diode interposer
  12  *
  13  * Michal Simek <michal.simek@amd.com>
  14  */
  15
  16 #include <dt-bindings/gpio/gpio.h>
  17 #include <dt-bindings/net/ti-dp83867.h>
  18 #include <dt-bindings/phy/phy.h>
  19 #include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
  20
  21 /dts-v1/;
  22 /plugin/;
  23
  24 &{/} {
  25         si5332_0: si5332-0 { /* u17 */
  26                 compatible = "fixed-clock";
  27                 #clock-cells = <0>;
  28                 clock-frequency = <125000000>;
  29         };
  30
  31         si5332_1: si5332-1 { /* u17 */
  32                 compatible = "fixed-clock";
  33                 #clock-cells = <0>;
  34                 clock-frequency = <25000000>;
  35         };
  36
  37         si5332_2: si5332-2 { /* u17 */
  38                 compatible = "fixed-clock";
  39                 #clock-cells = <0>;
  40                 clock-frequency = <48000000>;
  41         };
  42
  43         si5332_3: si5332-3 { /* u17 */
  44                 compatible = "fixed-clock";
  45                 #clock-cells = <0>;
  46                 clock-frequency = <24000000>;
  47         };
  48
  49         si5332_4: si5332-4 { /* u17 */
  50                 compatible = "fixed-clock";
  51                 #clock-cells = <0>;
  52                 clock-frequency = <26000000>;
  53         };
  54
  55         si5332_5: si5332-5 { /* u17 */
  56                 compatible = "fixed-clock";
  57                 #clock-cells = <0>;
  58                 clock-frequency = <27000000>;
  59         };
  60 };
  61
  62 &i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
  63         #address-cells = <1>;
  64         #size-cells = <0>;
  65         pinctrl-names = "default", "gpio";
  66         pinctrl-0 = <&pinctrl_i2c1_default>;
  67         pinctrl-1 = <&pinctrl_i2c1_gpio>;
  68         scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  69         sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
  70
  71         /* u14 - 0x40 - ina260 */
  72         /* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
  73 };
  74
  75 /* DP/USB 3.0 and SATA */
  76 &psgtr {
  77         status = "okay";
  78         /* pcie, usb3, sata */
  79         clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
  80         clock-names = "ref0", "ref1", "ref2";
  81 };
  82
  83 &sata {
  84         status = "okay";
  85         /* SATA OOB timing settings */
  86         ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
  87         ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
  88         ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
  89         ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
  90         ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
  91         ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
  92         ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
  93         ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
  94         phy-names = "sata-phy";
  95         phys = <&psgtr 3 PHY_TYPE_SATA 1 2>;
  96 };
  97
  98 &zynqmp_dpsub {
  99         status = "okay";
 100         phy-names = "dp-phy0", "dp-phy1";
 101         phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
 102         assigned-clock-rates = <27000000>, <25000000>, <300000000>;
 103 };
 104
 105 &zynqmp_dpdma {
 106         status = "okay";
 107         assigned-clock-rates = <600000000>;
 108 };
 109
 110 &usb0 {
 111         status = "okay";
 112         pinctrl-names = "default";
 113         pinctrl-0 = <&pinctrl_usb0_default>;
 114         phy-names = "usb3-phy";
 115         phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
 116         /* missing usb5744 - u43 */
 117 };
 118
 119 &dwc3_0 {
 120         status = "okay";
 121         dr_mode = "host";
 122         snps,usb3_lpm_capable;
 123         maximum-speed = "super-speed";
 124 };
 125
 126 &sdhci1 { /* on CC with tuned parameters */
 127         status = "okay";
 128         pinctrl-names = "default";
 129         pinctrl-0 = <&pinctrl_sdhci1_default>;
 130         /*
 131          * SD 3.0 requires level shifter and this property
 132          * should be removed if the board has level shifter and
 133          * need to work in UHS mode
 134          */
 135         no-1-8-v;
 136         disable-wp;
 137         xlnx,mio-bank = <1>;
 138         assigned-clock-rates = <187498123>;
 139         bus-width = <4>;
 140 };
 141
 142 &gem3 { /* required by spec */
 143         status = "okay";
 144         pinctrl-names = "default";
 145         pinctrl-0 = <&pinctrl_gem3_default>;
 146         phy-handle = <&phy0>;
 147         phy-mode = "rgmii-id";
 148         assigned-clock-rates = <250000000>;
 149
 150         mdio: mdio {
 151                 #address-cells = <1>;
 152                 #size-cells = <0>;
 153
 154                 phy0: ethernet-phy@1 {
 155                         #phy-cells = <1>;
 156                         reg = <1>;
 157                         compatible = "ethernet-phy-id2000.a231";
 158                         ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
 159                         ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
 160                         ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 161                         ti,dp83867-rxctrl-strap-quirk;
 162                         reset-assert-us = <100>;
 163                         reset-deassert-us = <280>;
 164                         reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
 165                 };
 166         };
 167 };
 168
 169 &pinctrl0 { /* required by spec */
 170         status = "okay";
 171
 172         pinctrl_uart1_default: uart1-default {
 173                 conf {
 174                         groups = "uart1_9_grp";
 175                         slew-rate = <SLEW_RATE_SLOW>;
 176                         power-source = <IO_STANDARD_LVCMOS18>;
 177                         drive-strength = <12>;
 178                 };
 179
 180                 conf-rx {
 181                         pins = "MIO37";
 182                         bias-high-impedance;
 183                 };
 184
 185                 conf-tx {
 186                         pins = "MIO36";
 187                         bias-disable;
 188                 };
 189
 190                 mux {
 191                         groups = "uart1_9_grp";
 192                         function = "uart1";
 193                 };
 194         };
 195
 196         pinctrl_i2c1_default: i2c1-default {
 197                 conf {
 198                         groups = "i2c1_6_grp";
 199                         bias-pull-up;
 200                         slew-rate = <SLEW_RATE_SLOW>;
 201                         power-source = <IO_STANDARD_LVCMOS18>;
 202                 };
 203
 204                 mux {
 205                         groups = "i2c1_6_grp";
 206                         function = "i2c1";
 207                 };
 208         };
 209
 210         pinctrl_i2c1_gpio: i2c1-gpio {
 211                 conf {
 212                         groups = "gpio0_24_grp", "gpio0_25_grp";
 213                         slew-rate = <SLEW_RATE_SLOW>;
 214                         power-source = <IO_STANDARD_LVCMOS18>;
 215                 };
 216
 217                 mux {
 218                         groups = "gpio0_24_grp", "gpio0_25_grp";
 219                         function = "gpio0";
 220                 };
 221         };
 222
 223         pinctrl_gem3_default: gem3-default {
 224                 conf {
 225                         groups = "ethernet3_0_grp";
 226                         slew-rate = <SLEW_RATE_SLOW>;
 227                         power-source = <IO_STANDARD_LVCMOS18>;
 228                 };
 229
 230                 conf-rx {
 231                         pins = "MIO70", "MIO72", "MIO74";
 232                         bias-high-impedance;
 233                         low-power-disable;
 234                 };
 235
 236                 conf-bootstrap {
 237                         pins = "MIO71", "MIO73", "MIO75";
 238                         bias-disable;
 239                         low-power-disable;
 240                 };
 241
 242                 conf-tx {
 243                         pins = "MIO64", "MIO65", "MIO66",
 244                                 "MIO67", "MIO68", "MIO69";
 245                         bias-disable;
 246                         low-power-enable;
 247                 };
 248
 249                 conf-mdio {
 250                         groups = "mdio3_0_grp";
 251                         slew-rate = <SLEW_RATE_SLOW>;
 252                         power-source = <IO_STANDARD_LVCMOS18>;
 253                         bias-disable;
 254                 };
 255
 256                 mux-mdio {
 257                         function = "mdio3";
 258                         groups = "mdio3_0_grp";
 259                 };
 260
 261                 mux {
 262                         function = "ethernet3";
 263                         groups = "ethernet3_0_grp";
 264                 };
 265         };
 266
 267         pinctrl_usb0_default: usb0-default {
 268                 conf {
 269                         groups = "usb0_0_grp";
 270                         power-source = <IO_STANDARD_LVCMOS18>;
 271                 };
 272
 273                 conf-rx {
 274                         pins = "MIO52", "MIO53", "MIO55";
 275                         bias-high-impedance;
 276                         drive-strength = <12>;
 277                         slew-rate = <SLEW_RATE_FAST>;
 278                 };
 279
 280                 conf-tx {
 281                         pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 282                         "MIO60", "MIO61", "MIO62", "MIO63";
 283                         bias-disable;
 284                         drive-strength = <4>;
 285                         slew-rate = <SLEW_RATE_SLOW>;
 286                 };
 287
 288                 mux {
 289                         groups = "usb0_0_grp";
 290                         function = "usb0";
 291                 };
 292         };
 293
 294         pinctrl_sdhci1_default: sdhci1-default {
 295                 conf {
 296                         groups = "sdio1_0_grp";
 297                         slew-rate = <SLEW_RATE_SLOW>;
 298                         power-source = <IO_STANDARD_LVCMOS18>;
 299                         bias-disable;
 300                 };
 301
 302                 conf-cd {
 303                         groups = "sdio1_cd_0_grp";
 304                         bias-high-impedance;
 305                         bias-pull-up;
 306                         slew-rate = <SLEW_RATE_SLOW>;
 307                         power-source = <IO_STANDARD_LVCMOS18>;
 308                 };
 309
 310                 mux-cd {
 311                         groups = "sdio1_cd_0_grp";
 312                         function = "sdio1_cd";
 313                 };
 314
 315                 mux {
 316                         groups = "sdio1_0_grp";
 317                         function = "sdio1";
 318                 };
 319         };
 320 };
 321
 322 &uart1 {
 323         status = "okay";
 324         pinctrl-names = "default";
 325         pinctrl-0 = <&pinctrl_uart1_default>;
 326 };