2 * Qualcomm Atheros OUI and vendor specific assignments
3 * Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
4 * Copyright (c) 2018, The Linux Foundation
6 * This software may be distributed under the terms of the BSD license.
7 * See README for more details.
14 * This file is a registry of identifier assignments from the Qualcomm Atheros
15 * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers
16 * can be assigned through normal review process for changes to the upstream
17 * hostap.git repository.
20 #define OUI_QCA 0x001374
23 * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs
25 enum qca_radiotap_vendor_ids
{
26 QCA_RADIOTAP_VID_WLANTEST
= 0,
30 * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
32 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0
34 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event
36 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use
37 * internal BSS-selection. This command uses
38 * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy
39 * for the current connection (i.e., changes policy set by the nl80211
40 * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be
41 * included to indicate which BSS to use in case roaming is disabled.
43 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency
44 * ranges to avoid to reduce issues due to interference or internal
45 * co-existence information in the driver. The event data structure is
46 * defined in struct qca_avoid_freq_list.
48 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support
51 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass
52 * NAN Request/Response and NAN Indication messages. These messages are
53 * interpreted between the framework and the firmware component. While
54 * sending the command from userspace to the driver, payload is not
55 * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN
56 * is used when receiving vendor events in userspace from the driver.
58 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be
59 * used to configure PMK to the driver even when not connected. This can
60 * be used to request offloading of key management operations. Only used
61 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
63 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of
64 * NL80211_CMD_ROAM event with optional attributes including information
65 * from offloaded key management operation. Uses
66 * enum qca_wlan_vendor_attr_roam_auth attributes. Only used
67 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
69 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to
70 * invoke the ACS function in device and pass selected channels to
73 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features
74 * supported by the driver. enum qca_wlan_vendor_features defines
75 * the possible features.
77 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver,
78 * which supports DFS offloading, to indicate a channel availability check
81 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver,
82 * which supports DFS offloading, to indicate a channel availability check
85 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver,
86 * which supports DFS offloading, to indicate that the channel availability
87 * check aborted, no change to the channel status.
89 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by
90 * driver, which supports DFS offloading, to indicate that the
91 * Non-Occupancy Period for this channel is over, channel becomes usable.
93 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver,
94 * which supports DFS offloading, to indicate a radar pattern has been
95 * detected. The channel is now unusable.
97 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap
98 * based on enum wifi_logger_supported_features. Attributes defined in
99 * enum qca_wlan_vendor_attr_get_logger_features.
101 * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular
102 * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the
103 * attribute for this command. Attributes defined in
104 * enum qca_wlan_vendor_attr_wifi_logger_start.
106 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS
107 * capabilities of the driver, parameters includes the attributes defined
108 * in enum qca_wlan_vendor_attr_tdls_get_capabilities.
110 * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload
111 * sending of certain periodic IP packet to firmware, attributes defined in
112 * enum qca_wlan_vendor_attr_offloaded_packets.
114 * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI
115 * monitoring, defines min and max RSSI which are configured for RSSI
116 * monitoring. Also used to notify the RSSI breach and provides the BSSID
117 * and RSSI value that was breached. Attributes defined in
118 * enum qca_wlan_vendor_attr_rssi_monitoring.
120 * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN
121 * Data Path (NDP) related operations, attributes defined in
122 * enum qca_wlan_vendor_attr_ndp_params.
124 * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable
125 * Neighbour Discovery offload, attributes defined in
126 * enum qca_wlan_vendor_attr_nd_offload.
128 * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various
129 * configuration parameter for BPF packet filter, attributes defined in
130 * enum qca_wlan_vendor_attr_packet_filter.
132 * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware
133 * maximum supported size, attributes defined in
134 * enum qca_wlan_vendor_drv_info.
136 * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various
137 * data about wake reasons and datapath IP statistics, attributes defined
138 * in enum qca_wlan_vendor_attr_wake_stats.
140 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration
141 * for IEEE 802.11 communicating outside the context of a basic service
142 * set, called OCB command. Uses the attributes defines in
143 * enum qca_wlan_vendor_attr_ocb_set_config.
145 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB
146 * UTC time. Use the attributes defines in
147 * enum qca_wlan_vendor_attr_ocb_set_utc_time.
149 * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start
150 * sending OCB timing advert frames. Uses the attributes defines in
151 * enum qca_wlan_vendor_attr_ocb_start_timing_advert.
153 * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop
154 * OCB timing advert. Uses the attributes defines in
155 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert.
157 * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF
158 * timer value. Uses the attributes defines in
159 * enum qca_wlan_vendor_attr_ocb_get_tsf_resp.
161 * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: Command/event to update the
162 * link properties of the respective interface. As an event, is used
163 * to notify the connected station's status. The attributes for this
164 * command are defined in enum qca_wlan_vendor_attr_link_properties.
166 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
167 * start the P2P Listen offload function in device and pass the listen
168 * channel, period, interval, count, device types, and vendor specific
169 * information elements to the device driver and firmware.
170 * Uses the attributes defines in
171 * enum qca_wlan_vendor_attr_p2p_listen_offload.
173 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to
174 * indicate stop request/response of the P2P Listen offload function in
175 * device. As an event, it indicates either the feature stopped after it
176 * was already running or feature has actually failed to start. Uses the
177 * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
179 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
180 * beaconing, this sub command provides the driver, the frequencies on the
181 * 5 GHz band to check for any radar activity. Driver selects one channel
182 * from this priority list provided through
183 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
184 * to check for radar activity on it. If no radar activity is detected
185 * during the channel availability check period, driver internally switches
186 * to the selected frequency of operation. If the frequency is zero, driver
187 * internally selects a channel. The status of this conditional switch is
188 * indicated through an event using the same sub command through
189 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
190 * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
192 * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
193 * attributes defined in enum qca_wlan_gpio_attr.
195 * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
196 * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
197 * capabilities are to be fetched and other
198 * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
199 * requested capabilities.
201 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
202 * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
205 * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for
206 * indoor location features. Capabilities are reported in
207 * QCA_WLAN_VENDOR_ATTR_LOC_CAPA.
209 * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM
210 * (fine timing measurement) session with one or more peers.
211 * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and
212 * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS.
213 * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
214 * events will be reported, followed by
215 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate
217 * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6
219 * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session.
220 * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with
221 * status code indicating session was aborted.
223 * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement
224 * results for one peer. Results are reported in
225 * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS.
227 * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when
228 * FTM session is finished, either successfully or aborted by
231 * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder
232 * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether
233 * to enable or disable the responder. LCI/LCR reports can be
234 * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and
235 * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple
236 * times to update the LCI/LCR reports.
238 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of
239 * arrival) measurement with a single peer. Specify peer MAC address in
240 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in
241 * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel
242 * scan results cache and use the frequency from there).
243 * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE.
244 * Measurement result is reported in
245 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event.
247 * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify
248 * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
250 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports
251 * the AOA measurement result.
252 * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
253 * success/failure status is reported in
254 * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS.
255 * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
256 * The antenna array(s) used in the measurement are reported in
257 * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK.
259 * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given
260 * data as per the given parameters.
262 * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a
265 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level
266 * configuration for a DMG RF sector. Specify sector index in
267 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
268 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules
269 * to return sector information for in
270 * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration
271 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the
272 * exact time where information was captured in
273 * QCA_WLAN_VENDOR_ATTR_TSF.
275 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level
276 * configuration for a DMG RF sector. Specify sector index in
277 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
278 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration
279 * for one or more DMG RF modules in
280 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG.
282 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected
283 * DMG RF sector for a station. This is the sector that the HW
284 * will use to communicate with the station. Specify the MAC address
285 * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not
286 * needed for unassociated station). Specify sector type to return in
287 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected
288 * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
289 * Also return the exact time where the information was captured
290 * in QCA_WLAN_VENDOR_ATTR_TSF.
292 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the
293 * selected DMG RF sector for a station. This is the sector that
294 * the HW will use to communicate with the station.
295 * Specify the MAC address of associated station/AP/PCP in
296 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in
297 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index
298 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
299 * The selected sector will be locked such that it will not be
300 * modified like it normally does (for example when station
301 * moves around). To unlock the selected sector for a station
302 * pass the special value 0xFFFF in the sector index. To unlock
303 * all connected stations also pass a broadcast MAC address.
305 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior
306 * in the host driver. The different TDLS configurations are defined
307 * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration.
309 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE
310 * capabilities. The response uses the attributes defined in
311 * enum qca_wlan_vendor_attr_get_he_capabilities.
313 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was
314 * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
315 * carries the scan cookie of the corresponding scan request. The scan
316 * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
318 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
319 * Absorption Rate (SAR) power limits. A critical regulation for
320 * FCC compliance, OEMs require methods to set SAR limits on TX
321 * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
322 * attributes are used with this command.
324 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the
325 * host driver for offloading the implementation of Auto Channel Selection
326 * (ACS) to an external user space entity. This interface is used as the
327 * event from the host driver to the user space entity and also as the
328 * request from the user space entity to the host driver. The event from
329 * the host driver is used by the user space entity as an indication to
330 * start the ACS functionality. The attributes used by this event are
331 * represented by the enum qca_wlan_vendor_attr_external_acs_event.
332 * User space entity uses the same interface to inform the host driver with
333 * selected channels after the ACS operation using the attributes defined
334 * by enum qca_wlan_vendor_attr_external_acs_channels.
336 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the
337 * requisite information leading to a power save failure. The information
338 * carried as part of this event is represented by the
339 * enum qca_attr_chip_power_save_failure attributes.
341 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics
342 * collection. Uses attributes defined in enum qca_attr_nud_stats_set.
344 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These
345 * statistics are represented by the enum qca_attr_nud_stats_get
348 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch
349 * the BSS transition status, whether accept or reject, for a list of
350 * candidate BSSIDs provided by the userspace. This uses the vendor
351 * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and
352 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify
353 * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an
354 * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in
355 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response
356 * the driver shall specify array of
357 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and
358 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in
359 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO.
361 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a
362 * specific QCA module. The trace levels are represented by
363 * enum qca_attr_trace_level attributes.
365 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement
366 * Protocol antenna limit in different modes. See enum
367 * qca_wlan_vendor_attr_brp_ant_limit_mode.
369 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan
370 * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan.
371 * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE)
372 * identifying the operation in success case.
374 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses
375 * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from
376 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to
379 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the
380 * specific interface. This can be used to modify some of the low level
381 * scan parameters (off channel dwell time, home channel time) in the
382 * driver/firmware. These parameters are maintained within the host driver.
383 * This command is valid only when the interface is in the connected state.
384 * These scan parameters shall be reset by the driver/firmware once
385 * disconnected. The attributes used with this command are defined in
386 * enum qca_wlan_vendor_attr_active_tos.
388 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the
389 * driver has detected an internal failure. This event carries the
390 * information indicating the reason that triggered this detection. The
391 * attributes for this command are defined in
392 * enum qca_wlan_vendor_attr_hang.
394 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values
395 * of spectral parameters used. The spectral scan parameters are specified
396 * by enum qca_wlan_vendor_attr_spectral_scan.
398 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats
399 * for spectral scan functionality. The debug stats are specified by
400 * enum qca_wlan_vendor_attr_spectral_diag_stats.
402 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral
403 * scan system capabilities. The capabilities are specified
404 * by enum qca_wlan_vendor_attr_spectral_cap.
406 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current
407 * status of spectral scan. The status values are specified
408 * by enum qca_wlan_vendor_attr_spectral_scan_status.
410 * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush
411 * peer pending packets. Specify the peer MAC address in
412 * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets
413 * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed
414 * in enum qca_wlan_vendor_attr_flush_pending.
416 * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative
417 * RF Operating Parameter (RROP) information. The attributes for this
418 * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is
419 * intended for use by external Auto Channel Selection applications.
421 * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate
422 * (SAR) power limits. This is a companion to the command
423 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the
424 * settings currently in use. The attributes returned by this command are
425 * defined by enum qca_vendor_attr_sar_limits.
427 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of
428 * the WLAN hardware MAC. Also, provides the WLAN netdev interface
429 * information attached to the respective MAC.
430 * This works both as a query (user space asks the current mode) or event
431 * interface (driver advertising the current mode to the user space).
432 * Driver does not trigger this event for temporary hardware mode changes.
433 * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion,
434 * channel change, etc.) are updated with this event. Attributes for this
435 * interface are defined in enum qca_wlan_vendor_attr_mac.
437 * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold
438 * per peer per TID. Attributes for this command are define in
439 * enum qca_wlan_set_qdepth_thresh_attr.
440 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action
441 * guide for WLAN driver. Request to suspend of driver and FW if the
442 * temperature is higher than the suspend threshold; resume action is
443 * requested to driver if the temperature is lower than the resume
444 * threshold. In user poll mode, request temperature data by user. For test
445 * purpose, getting thermal shutdown configuration parameters is needed.
446 * Attributes for this interface are defined in
447 * enum qca_wlan_vendor_attr_thermal_cmd.
448 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from
449 * driver. Thermal temperature and indication of resume completion are
450 * reported as thermal events. The attributes for this command are defined
451 * in enum qca_wlan_vendor_attr_thermal_event.
453 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi
454 * test configuration. Attributes for this command are defined in
455 * enum qca_wlan_vendor_attr_wifi_test_config.
457 * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an
458 * RX filter to receive frames from stations that are active on the
459 * operating channel, but not associated with the local device (e.g., STAs
460 * associated with other APs). Filtering is done based on a list of BSSIDs
461 * and STA MAC addresses added by the user. This command is also used to
462 * fetch the statistics of unassociated stations. The attributes used with
463 * this command are defined in enum qca_wlan_vendor_attr_bss_filter.
465 * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor
466 * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN,
467 * carried a payload which was a binary blob of data. The command was not
468 * extendable to send more information. The newer version carries the
469 * legacy blob encapsulated within an attribute and can be extended with
470 * additional vendor attributes that can enhance the NAN command interface.
471 * @QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT: Event to indicate scan triggered
472 * or stopped within driver/firmware in order to initiate roaming. The
473 * attributes used with this event are defined in enum
474 * qca_wlan_vendor_attr_roam_scan. Some drivers may not send these events
475 * in few cases, e.g., if the host processor is sleeping when this event
476 * is generated in firmware.
478 * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to
479 * configure parameters per peer to capture Channel Frequency Response
480 * (CFR) and enable Periodic CFR capture. The attributes for this command
481 * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr.
483 * @QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT: Event to indicate changes
484 * in throughput dynamically. The driver estimates the throughput based on
485 * number of packets being transmitted/received per second and indicates
486 * the changes in throughput to user space. Userspace tools can use this
487 * information to configure kernel's TCP parameters in order to achieve
488 * peak throughput. Optionally, the driver will also send guidance on
489 * modifications to kernel's TCP parameters which can be referred by
490 * userspace tools. The attributes used with this event are defined in enum
491 * qca_wlan_vendor_attr_throughput_change.
493 * @QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG: This command is used to set
494 * priorities among different types of traffic during coex scenarios.
495 * Current supported prioritization is among WLAN/BT/ZIGBEE with different
496 * profiles mentioned in enum qca_coex_config_profiles. The associated
497 * attributes used with this command are defined in enum
498 * qca_vendor_attr_coex_config.
500 * Based on the config provided, FW will boost the weight and prioritize
501 * the traffic for that subsystem (WLAN/BT/Zigbee).
503 enum qca_nl80211_vendor_subcmds
{
504 QCA_NL80211_VENDOR_SUBCMD_UNSPEC
= 0,
505 QCA_NL80211_VENDOR_SUBCMD_TEST
= 1,
506 /* subcmds 2..8 not yet allocated */
507 QCA_NL80211_VENDOR_SUBCMD_ROAMING
= 9,
508 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY
= 10,
509 QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY
= 11,
510 QCA_NL80211_VENDOR_SUBCMD_NAN
= 12,
511 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT
= 13,
512 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET
= 14,
513 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET
= 15,
514 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR
= 16,
515 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS
= 17,
516 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS
= 18,
517 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS
= 19,
518 QCA_NL80211_VENDOR_SUBCMD_GSCAN_START
= 20,
519 QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP
= 21,
520 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS
= 22,
521 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES
= 23,
522 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS
= 24,
523 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE
= 25,
524 QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT
= 26,
525 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT
= 27,
526 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND
= 28,
527 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST
= 29,
528 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST
= 30,
529 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE
= 31,
530 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE
= 32,
531 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE
= 33,
532 QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE
= 34,
533 QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE
= 35,
534 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS
= 36,
535 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE
= 37,
536 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES
= 38,
537 QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI
= 39,
538 QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG
= 40,
539 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST
= 41,
540 QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX
= 42,
541 /* 43..49 - reserved for QCA */
542 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY
= 50,
543 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH
= 51,
544 QCA_NL80211_VENDOR_SUBCMD_APFIND
= 52,
545 /* 53 - reserved - was used by QCA, but not in use anymore */
546 QCA_NL80211_VENDOR_SUBCMD_DO_ACS
= 54,
547 QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES
= 55,
548 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED
= 56,
549 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED
= 57,
550 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED
= 58,
551 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED
= 59,
552 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED
= 60,
553 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO
= 61,
554 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START
= 62,
555 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP
= 63,
556 QCA_NL80211_VENDOR_SUBCMD_ROAM
= 64,
557 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST
= 65,
558 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST
= 66,
559 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND
= 67,
560 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST
= 68,
561 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST
= 69,
562 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST
= 70,
563 QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST
= 71,
564 QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND
= 72,
565 QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND
= 73,
566 /* Wi-Fi configuration subcommands */
567 QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION
= 74,
568 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION
= 75,
569 QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET
= 76,
570 QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA
= 77,
571 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES
= 78,
572 QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS
= 79,
573 QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI
= 80,
574 QCA_NL80211_VENDOR_SUBCMD_NDP
= 81,
575 QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD
= 82,
576 QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER
= 83,
577 QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE
= 84,
578 QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS
= 85,
579 /* 86-90 - reserved for QCA */
580 QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD
= 91,
581 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG
= 92,
582 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME
= 93,
583 QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT
= 94,
584 QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT
= 95,
585 QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER
= 96,
586 QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS
= 97,
587 QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS
= 98,
588 QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL
= 99,
589 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT
= 100,
590 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES
= 101,
591 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG
= 102,
592 QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST
= 103,
593 QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL
= 104,
594 QCA_NL80211_VENDOR_SUBCMD_SETBAND
= 105,
595 QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN
= 106,
596 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE
= 107,
597 QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
= 108,
598 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE
= 109,
599 /* 110..114 - reserved for QCA */
600 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB
= 115,
601 /* 116..117 - reserved for QCA */
602 QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG
= 118,
603 QCA_NL80211_VENDOR_SUBCMD_TSF
= 119,
604 QCA_NL80211_VENDOR_SUBCMD_WISA
= 120,
605 /* 121 - reserved for QCA */
606 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START
= 122,
607 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP
= 123,
608 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH
= 124,
609 QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND
= 125,
610 QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY
= 126,
611 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT
= 127,
612 /* FTM/indoor location subcommands */
613 QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA
= 128,
614 QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
= 129,
615 QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION
= 130,
616 QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
= 131,
617 QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE
= 132,
618 QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
= 133,
619 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
= 134,
620 QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS
= 135,
621 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
= 136,
622 QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST
= 137,
623 QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI
= 138,
624 /* DMG low level RF sector operations */
625 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG
= 139,
626 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
= 140,
627 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR
= 141,
628 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR
= 142,
629 QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS
= 143,
630 QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES
= 144,
631 QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN
= 145,
632 QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
= 146,
633 QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
= 147,
634 QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE
= 148,
635 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET
= 149,
636 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET
= 150,
637 QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS
= 151,
638 QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL
= 152,
639 QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT
= 153,
640 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
= 154,
641 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP
= 155,
642 QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS
= 156,
643 QCA_NL80211_VENDOR_SUBCMD_HANG
= 157,
644 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG
= 158,
645 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS
= 159,
646 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO
= 160,
647 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS
= 161,
648 /* Flush peer pending data */
649 QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING
= 162,
650 QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO
= 163,
651 QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS
= 164,
652 QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO
= 165,
653 QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
= 166,
654 /* Thermal shutdown commands to protect wifi chip */
655 QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
= 167,
656 QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT
= 168,
657 /* Wi-Fi test configuration subcommand */
658 QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
= 169,
659 /* Frame filter operations for other BSSs/unassociated STAs */
660 QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER
= 170,
661 QCA_NL80211_VENDOR_SUBCMD_NAN_EXT
= 171,
662 QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT
= 172,
663 QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG
= 173,
664 QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT
= 174,
665 QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG
= 175,
668 enum qca_wlan_vendor_attr
{
669 QCA_WLAN_VENDOR_ATTR_INVALID
= 0,
670 /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */
671 QCA_WLAN_VENDOR_ATTR_DFS
= 1,
672 /* Used only when driver sends vendor events to the userspace under the
673 * command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends
674 * commands to the driver.
676 QCA_WLAN_VENDOR_ATTR_NAN
= 2,
677 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
678 QCA_WLAN_VENDOR_ATTR_STATS_EXT
= 3,
679 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
680 QCA_WLAN_VENDOR_ATTR_IFINDEX
= 4,
681 /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined
682 * by enum qca_roaming_policy.
684 QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY
= 5,
685 QCA_WLAN_VENDOR_ATTR_MAC_ADDR
= 6,
686 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
687 QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS
= 7,
688 QCA_WLAN_VENDOR_ATTR_TEST
= 8,
689 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
690 /* Unsigned 32-bit value. */
691 QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA
= 9,
692 /* Unsigned 32-bit value */
693 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND
= 10,
694 /* Unsigned 32-bit value */
695 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND
= 11,
696 /* Unsigned 32-bit value from enum qca_set_band. */
697 QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE
= 12,
698 /* Dummy (NOP) attribute for 64 bit padding */
699 QCA_WLAN_VENDOR_ATTR_PAD
= 13,
700 /* Unique FTM session cookie (Unsigned 64 bit). Specified in
701 * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in
702 * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and
703 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE.
705 QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE
= 14,
706 /* Indoor location capabilities, returned by
707 * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA.
708 * see enum qca_wlan_vendor_attr_loc_capa.
710 QCA_WLAN_VENDOR_ATTR_LOC_CAPA
= 15,
711 /* Array of nested attributes containing information about each peer
712 * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info
713 * for supported attributes for each peer.
715 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS
= 16,
716 /* Array of nested attributes containing measurement results for
717 * one or more peers, reported by the
718 * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event.
719 * See enum qca_wlan_vendor_attr_peer_result for list of supported
722 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS
= 17,
723 /* Flag attribute for enabling or disabling responder functionality. */
724 QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE
= 18,
725 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
726 * command to specify the LCI report that will be sent by
727 * the responder during a measurement exchange. The format is
728 * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10.
730 QCA_WLAN_VENDOR_ATTR_FTM_LCI
= 19,
731 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
732 * command to specify the location civic report that will
733 * be sent by the responder during a measurement exchange.
734 * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13.
736 QCA_WLAN_VENDOR_ATTR_FTM_LCR
= 20,
737 /* Session/measurement completion status code,
738 * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and
739 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
740 * see enum qca_vendor_attr_loc_session_status.
742 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS
= 21,
743 /* Initial dialog token used by responder (0 if not specified),
744 * unsigned 8 bit value.
746 QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN
= 22,
747 /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
748 * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if
749 * AOA measurements are needed as part of an FTM session.
750 * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See
751 * enum qca_wlan_vendor_attr_aoa_type.
753 QCA_WLAN_VENDOR_ATTR_AOA_TYPE
= 23,
754 /* A bit mask (unsigned 32 bit value) of antenna arrays used
755 * by indoor location measurements. Refers to the antenna
756 * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS.
758 QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK
= 24,
759 /* AOA measurement data. Its contents depends on the AOA measurement
760 * type and antenna array mask:
761 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values,
762 * phase of the strongest CIR path for each antenna in the measured
764 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16
765 * values, phase and amplitude of the strongest CIR path for each
766 * antenna in the measured array(s).
768 QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT
= 25,
769 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
770 * to specify the chain number (unsigned 32 bit value) to inquire
771 * the corresponding antenna RSSI value
773 QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX
= 26,
774 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
775 * to report the specific antenna RSSI value (unsigned 32 bit value)
777 QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI
= 27,
778 /* Frequency in MHz, various uses. Unsigned 32 bit value */
779 QCA_WLAN_VENDOR_ATTR_FREQ
= 28,
780 /* TSF timer value, unsigned 64 bit value.
781 * May be returned by various commands.
783 QCA_WLAN_VENDOR_ATTR_TSF
= 29,
784 /* DMG RF sector index, unsigned 16 bit number. Valid values are
785 * 0..127 for sector indices or 65535 as special value used to
786 * unlock sector selection in
787 * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR.
789 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX
= 30,
790 /* DMG RF sector type, unsigned 8 bit value. One of the values
791 * in enum qca_wlan_vendor_attr_dmg_rf_sector_type.
793 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE
= 31,
794 /* Bitmask of DMG RF modules for which information is requested. Each
795 * bit corresponds to an RF module with the same index as the bit
796 * number. Unsigned 32 bit number but only low 8 bits can be set since
797 * all DMG chips currently have up to 8 RF modules.
799 QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK
= 32,
800 /* Array of nested attributes where each entry is DMG RF sector
801 * configuration for a single RF module.
802 * Attributes for each entry are taken from enum
803 * qca_wlan_vendor_attr_dmg_rf_sector_cfg.
804 * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
805 * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG.
807 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG
= 33,
808 /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command
809 * to report frame aggregation statistics to userspace.
811 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM
= 34,
812 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO
= 35,
813 /* Unsigned 8-bit value representing MBO transition reason code as
814 * provided by the AP used by subcommand
815 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is
816 * specified by the userspace in the request to the driver.
818 QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON
= 36,
819 /* Array of nested attributes, BSSID and status code, used by subcommand
820 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each
821 * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info.
822 * The userspace space specifies the list/array of candidate BSSIDs in
823 * the order of preference in the request. The driver specifies the
824 * status code, for each BSSID in the list, in the response. The
825 * acceptable candidates are listed in the order preferred by the
828 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO
= 37,
829 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
830 * See enum qca_wlan_vendor_attr_brp_ant_limit_mode.
832 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE
= 38,
833 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
834 * to define the number of antennas to use for BRP.
835 * different purpose in each ANT_LIMIT_MODE:
837 * EFFECTIVE - upper limit to number of antennas to be used
838 * FORCE - exact number of antennas to be used
839 * unsigned 8 bit value
841 QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT
= 39,
842 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
843 * to report the corresponding antenna index to the chain RSSI value
845 QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO
= 40,
848 QCA_WLAN_VENDOR_ATTR_AFTER_LAST
,
849 QCA_WLAN_VENDOR_ATTR_MAX
= QCA_WLAN_VENDOR_ATTR_AFTER_LAST
- 1,
852 enum qca_roaming_policy
{
853 QCA_ROAMING_NOT_ALLOWED
,
854 QCA_ROAMING_ALLOWED_WITHIN_ESS
,
857 enum qca_wlan_vendor_attr_roam_auth
{
858 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID
= 0,
859 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID
,
860 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE
,
861 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE
,
862 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED
,
863 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR
,
864 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK
,
865 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK
,
866 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS
,
867 /* Indicates the status of re-association requested by user space for
868 * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID.
870 * Represents the status code from AP. Use
871 * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the
872 * real status code for failures.
874 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS
,
875 /* This attribute indicates that the old association was maintained when
876 * a re-association is requested by user space and that re-association
877 * attempt fails (i.e., cannot connect to the requested BSS, but can
878 * remain associated with the BSS with which the association was in
879 * place when being requested to roam). Used along with
880 * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current
881 * re-association status. Type flag.
882 * This attribute is applicable only for re-association failure cases.
884 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION
,
885 /* This attribute specifies the PMK if one was newly generated during
886 * FILS roaming. This is added to the PMKSA cache and is used in
887 * subsequent connections with PMKSA caching.
889 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK
= 11,
890 /* This attribute specifies the PMKID used/generated for the current
891 * FILS roam. This is used in subsequent connections with PMKSA caching.
893 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID
= 12,
894 /* A 16-bit unsigned value specifying the next sequence number to use
895 * in ERP message in the currently associated realm. This is used in
896 * doing subsequent ERP based connections in the same realm.
898 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM
= 13,
900 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST
,
901 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX
=
902 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST
- 1
905 enum qca_wlan_vendor_attr_p2p_listen_offload
{
906 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID
= 0,
907 /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
908 * of the social channels.
910 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL
,
911 /* A 32-bit unsigned value; the P2P listen offload period (ms).
913 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD
,
914 /* A 32-bit unsigned value; the P2P listen interval duration (ms).
916 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL
,
917 /* A 32-bit unsigned value; number of interval times the firmware needs
918 * to run the offloaded P2P listen operation before it stops.
920 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT
,
921 /* An array of arbitrary binary data with one or more 8-byte values.
922 * The device types include both primary and secondary device types.
924 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES
,
925 /* An array of unsigned 8-bit characters; vendor information elements.
927 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE
,
928 /* A 32-bit unsigned value; a control flag to indicate whether listen
929 * results need to be flushed to wpa_supplicant.
931 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG
,
932 /* A 8-bit unsigned value; reason code for P2P listen offload stop
935 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON
,
937 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST
,
938 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX
=
939 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST
- 1
942 enum qca_wlan_vendor_attr_acs_offload
{
943 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID
= 0,
944 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL
,
945 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL
,
946 QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE
,
947 QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED
,
948 QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED
,
949 QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED
,
950 QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH
,
951 QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST
,
952 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL
,
953 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL
,
954 QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST
,
956 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST
,
957 QCA_WLAN_VENDOR_ATTR_ACS_MAX
=
958 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST
- 1
961 enum qca_wlan_vendor_acs_hw_mode
{
962 QCA_ACS_MODE_IEEE80211B
,
963 QCA_ACS_MODE_IEEE80211G
,
964 QCA_ACS_MODE_IEEE80211A
,
965 QCA_ACS_MODE_IEEE80211AD
,
966 QCA_ACS_MODE_IEEE80211ANY
,
970 * enum qca_wlan_vendor_features - Vendor device/driver feature flags
972 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key
973 * management offload, a mechanism where the station's firmware
974 * does the exchange with the AP to establish the temporal keys
975 * after roaming, rather than having the user space wpa_supplicant do it.
976 * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic
977 * band selection based on channel selection results.
978 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
979 * simultaneous off-channel operations.
980 * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
981 * Listen offload; a mechanism where the station's firmware takes care of
982 * responding to incoming Probe Request frames received from other P2P
983 * Devices whilst in Listen state, rather than having the user space
984 * wpa_supplicant do it. Information from received P2P requests are
985 * forwarded from firmware to host whenever the host processor wakes up.
986 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA
988 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific
990 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON
991 * specific features only. If a Device sets this bit but not the
992 * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that
993 * this Device may not support all OCE AP functionalities but can support
994 * only OCE STA-CFON functionalities.
995 * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self
996 * managed regulatory.
997 * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
999 enum qca_wlan_vendor_features
{
1000 QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD
= 0,
1001 QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY
= 1,
1002 QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS
= 2,
1003 QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD
= 3,
1004 QCA_WLAN_VENDOR_FEATURE_OCE_STA
= 4,
1005 QCA_WLAN_VENDOR_FEATURE_OCE_AP
= 5,
1006 QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON
= 6,
1007 QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY
= 7,
1008 NUM_QCA_WLAN_VENDOR_FEATURES
/* keep last */
1012 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication
1014 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to
1015 * the offloaded data.
1016 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded
1018 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload
1021 enum qca_wlan_vendor_attr_data_offload_ind
{
1022 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID
= 0,
1023 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION
,
1024 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL
,
1025 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT
,
1028 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST
,
1029 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX
=
1030 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST
- 1
1034 * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set
1037 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the
1039 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule
1040 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels
1041 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be
1043 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel
1045 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL
1046 * active state configuration
1047 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as
1048 * OCB_CONFIG_FLAG_80211_FRAME_MODE
1049 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to
1050 * use in the case that a packet is sent without a TX control header
1051 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the
1052 * last TA received that the local time set by TA is synchronous to other
1053 * communicating OCB STAs.
1055 enum qca_wlan_vendor_attr_ocb_set_config
{
1056 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID
= 0,
1057 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT
= 1,
1058 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE
= 2,
1059 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY
= 3,
1060 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY
= 4,
1061 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY
= 5,
1062 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY
= 6,
1063 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS
= 7,
1064 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM
= 8,
1065 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION
= 9,
1066 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST
,
1067 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX
=
1068 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST
- 1
1072 * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set
1075 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of
1077 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of
1080 enum qca_wlan_vendor_attr_ocb_set_utc_time
{
1081 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID
= 0,
1082 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE
= 1,
1083 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR
= 2,
1084 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST
,
1085 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX
=
1086 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST
- 1
1090 * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes
1091 * to start sending timing advert frames
1093 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency
1094 * on which to send the frames
1095 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times
1096 * the frame is sent in 5 seconds
1098 enum qca_wlan_vendor_attr_ocb_start_timing_advert
{
1099 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID
= 0,
1100 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ
= 1,
1101 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE
= 2,
1102 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST
,
1103 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX
=
1104 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST
- 1
1108 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes
1109 * to stop timing advert
1111 * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel
1112 * frequency on which to stop the timing advert
1114 enum qca_wlan_vendor_attr_ocb_stop_timing_advert
{
1115 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID
= 0,
1116 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ
= 1,
1117 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST
,
1118 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX
=
1119 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST
- 1
1123 * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to
1124 * get TSF timer value
1126 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the
1128 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer
1130 enum qca_wlan_vendor_attr_ocb_get_tsf_resp
{
1131 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID
= 0,
1132 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH
= 1,
1133 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW
= 2,
1134 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST
,
1135 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX
=
1136 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST
- 1
1139 enum qca_vendor_attr_get_preferred_freq_list
{
1140 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID
,
1141 /* A 32-unsigned value; the interface type/mode for which the preferred
1142 * frequency list is requested (see enum qca_iface_type for possible
1143 * values); used in GET_PREFERRED_FREQ_LIST command from user-space to
1144 * kernel and in the kernel response back to user-space.
1146 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE
,
1147 /* An array of 32-unsigned values; values are frequency (MHz); sent
1148 * from kernel space to user space.
1150 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST
,
1151 /* An array of nested values as per enum qca_wlan_vendor_attr_pcl
1152 * attribute. Each element contains frequency (MHz), weight, and flag
1153 * bit mask indicating how the frequency should be used in P2P
1154 * negotiation; sent from kernel space to user space.
1156 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL
,
1158 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST
,
1159 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX
=
1160 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST
- 1
1163 enum qca_vendor_attr_probable_oper_channel
{
1164 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID
,
1165 /* 32-bit unsigned value; indicates the connection/iface type likely to
1166 * come on this channel (see enum qca_iface_type).
1168 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE
,
1169 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */
1170 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ
,
1172 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST
,
1173 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX
=
1174 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST
- 1
1177 enum qca_iface_type
{
1180 QCA_IFACE_TYPE_P2P_CLIENT
,
1181 QCA_IFACE_TYPE_P2P_GO
,
1182 QCA_IFACE_TYPE_IBSS
,
1183 QCA_IFACE_TYPE_TDLS
,
1193 * enum qca_access_policy - Access control policy
1195 * Access control policy is applied on the configured IE
1196 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
1197 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
1199 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
1200 * the specific configuration (IE) set, i.e., allow all the
1201 * connections which do not match the configuration.
1202 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
1203 * the specific configuration (IE) set, i.e., deny all the
1204 * connections which do not match the configuration.
1206 enum qca_access_policy
{
1207 QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED
,
1208 QCA_ACCESS_POLICY_DENY_UNLESS_LISTED
,
1212 * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
1213 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
1214 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
1215 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized
1216 * SOC timer value at TSF capture
1218 enum qca_vendor_attr_tsf_cmd
{
1219 QCA_WLAN_VENDOR_ATTR_TSF_INVALID
= 0,
1220 QCA_WLAN_VENDOR_ATTR_TSF_CMD
,
1221 QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE
,
1222 QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE
,
1223 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST
,
1224 QCA_WLAN_VENDOR_ATTR_TSF_MAX
=
1225 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST
- 1
1229 * enum qca_tsf_operation: TSF driver commands
1230 * @QCA_TSF_CAPTURE: Initiate TSF Capture
1231 * @QCA_TSF_GET: Get TSF capture value
1232 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value
1241 * enum qca_vendor_attr_wisa_cmd
1242 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32)
1243 * WISA setup vendor commands
1245 enum qca_vendor_attr_wisa_cmd
{
1246 QCA_WLAN_VENDOR_ATTR_WISA_INVALID
= 0,
1247 QCA_WLAN_VENDOR_ATTR_WISA_MODE
,
1248 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST
,
1249 QCA_WLAN_VENDOR_ATTR_WISA_MAX
=
1250 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST
- 1
1253 /* IEEE 802.11 Vendor Specific elements */
1256 * enum qca_vendor_element_id - QCA Vendor Specific element types
1258 * These values are used to identify QCA Vendor Specific elements. The
1259 * payload of the element starts with the three octet OUI (OUI_QCA) and
1260 * is followed by a single octet type which is defined by this enum.
1262 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list.
1263 * This element can be used to specify preference order for supported
1264 * channels. The channels in this list are in preference order (the first
1265 * one has the highest preference) and are described as a pair of
1266 * (global) Operating Class and Channel Number (each one octet) fields.
1268 * This extends the standard P2P functionality by providing option to have
1269 * more than one preferred operating channel. When this element is present,
1270 * it replaces the preference indicated in the Operating Channel attribute.
1271 * For supporting other implementations, the Operating Channel attribute is
1272 * expected to be used with the highest preference channel. Similarly, all
1273 * the channels included in this Preferred channel list element are
1274 * expected to be included in the Channel List attribute.
1276 * This vendor element may be included in GO Negotiation Request, P2P
1277 * Invitation Request, and Provision Discovery Request frames.
1279 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
1280 * This element can be used for pre-standard publication testing of HE
1281 * before P802.11ax draft assigns the element ID. The payload of this
1282 * vendor specific element is defined by the latest P802.11ax draft.
1283 * Please note that the draft is still work in progress and this element
1284 * payload is subject to change.
1286 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
1287 * This element can be used for pre-standard publication testing of HE
1288 * before P802.11ax draft assigns the element ID. The payload of this
1289 * vendor specific element is defined by the latest P802.11ax draft.
1290 * Please note that the draft is still work in progress and this element
1291 * payload is subject to change.
1293 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set
1295 * This element can be used for pre-standard publication testing of HE
1296 * before P802.11ax draft assigns the element ID extension. The payload of
1297 * this vendor specific element is defined by the latest P802.11ax draft
1298 * (not including the Element ID Extension field). Please note that the
1299 * draft is still work in progress and this element payload is subject to
1302 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element.
1303 * This element can be used for pre-standard publication testing of HE
1304 * before P802.11ax draft assigns the element ID extension. The payload of
1305 * this vendor specific element is defined by the latest P802.11ax draft
1306 * (not including the Element ID Extension field). Please note that the
1307 * draft is still work in progress and this element payload is subject to
1310 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element.
1311 * This element can be used for pre-standard publication testing of HE
1312 * before P802.11ax draft assigns the element ID extension. The payload of
1313 * this vendor specific element is defined by the latest P802.11ax draft
1314 * (not including the Element ID Extension field). Please note that the
1315 * draft is still work in progress and this element payload is subject to
1318 enum qca_vendor_element_id
{
1319 QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST
= 0,
1320 QCA_VENDOR_ELEM_HE_CAPAB
= 1,
1321 QCA_VENDOR_ELEM_HE_OPER
= 2,
1322 QCA_VENDOR_ELEM_RAPS
= 3,
1323 QCA_VENDOR_ELEM_MU_EDCA_PARAMS
= 4,
1324 QCA_VENDOR_ELEM_BSS_COLOR_CHANGE
= 5,
1328 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes
1330 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan
1331 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes
1332 * with frequencies to be scanned (in MHz)
1333 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned
1334 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported
1335 * rates to be included
1336 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests
1337 * at non CCK rate in 2GHz band
1338 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags
1339 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the
1340 * driver for the specific scan request
1341 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan
1342 * request decoded as in enum scan_status
1343 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation
1345 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
1347 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
1348 * specific BSSID to scan for.
1350 enum qca_wlan_vendor_attr_scan
{
1351 QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM
= 0,
1352 QCA_WLAN_VENDOR_ATTR_SCAN_IE
= 1,
1353 QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES
= 2,
1354 QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS
= 3,
1355 QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES
= 4,
1356 QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE
= 5,
1357 QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS
= 6,
1358 QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE
= 7,
1359 QCA_WLAN_VENDOR_ATTR_SCAN_STATUS
= 8,
1360 QCA_WLAN_VENDOR_ATTR_SCAN_MAC
= 9,
1361 QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK
= 10,
1362 QCA_WLAN_VENDOR_ATTR_SCAN_BSSID
= 11,
1363 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST
,
1364 QCA_WLAN_VENDOR_ATTR_SCAN_MAX
=
1365 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST
- 1
1369 * enum scan_status - Specifies the valid values the vendor scan attribute
1370 * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take
1372 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with
1374 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between
1377 VENDOR_SCAN_STATUS_NEW_RESULTS
,
1378 VENDOR_SCAN_STATUS_ABORTED
,
1379 VENDOR_SCAN_STATUS_MAX
,
1383 * enum qca_vendor_attr_ota_test - Specifies the values for vendor
1384 * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
1385 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test
1387 enum qca_vendor_attr_ota_test
{
1388 QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID
,
1389 /* 8-bit unsigned value to indicate if OTA test is enabled */
1390 QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE
,
1392 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST
,
1393 QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX
=
1394 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST
- 1
1398 * enum qca_vendor_attr_txpower_scale - vendor sub commands index
1400 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value
1402 enum qca_vendor_attr_txpower_scale
{
1403 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID
,
1404 /* 8-bit unsigned value to indicate the scaling of tx power */
1405 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE
,
1407 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST
,
1408 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX
=
1409 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST
- 1
1413 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease
1415 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB.
1417 enum qca_vendor_attr_txpower_decr_db
{
1418 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID
,
1419 /* 8-bit unsigned value to indicate the reduction of TX power in dB for
1420 * a virtual interface.
1422 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB
,
1424 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST
,
1425 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX
=
1426 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST
- 1
1429 /* Attributes for data used by
1430 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
1431 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
1433 enum qca_wlan_vendor_attr_config
{
1434 QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID
= 0,
1435 /* Unsigned 32-bit value to set the DTIM period.
1436 * Whether the wifi chipset wakes at every dtim beacon or a multiple of
1437 * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
1440 QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM
= 1,
1441 /* Unsigned 32-bit value to set the wifi_iface stats averaging factor
1442 * used to calculate statistics like average the TSF offset or average
1443 * number of frame leaked.
1444 * For instance, upon Beacon frame reception:
1445 * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
1446 * For instance, when evaluating leaky APs:
1447 * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
1449 QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR
= 2,
1450 /* Unsigned 32-bit value to configure guard time, i.e., when
1451 * implementing IEEE power management based on frame control PM bit, how
1452 * long the driver waits before shutting down the radio and after
1453 * receiving an ACK frame for a Data frame with PM bit set.
1455 QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME
= 3,
1456 /* Unsigned 32-bit value to change the FTM capability dynamically */
1457 QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT
= 4,
1458 /* Unsigned 16-bit value to configure maximum TX rate dynamically */
1459 QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE
= 5,
1460 /* Unsigned 32-bit value to configure the number of continuous
1461 * Beacon Miss which shall be used by the firmware to penalize
1464 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS
= 6,
1465 /* Unsigned 8-bit value to configure the channel avoidance indication
1466 * behavior. Firmware to send only one indication and ignore duplicate
1467 * indications when set to avoid multiple Apps wakeups.
1469 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND
= 7,
1470 /* 8-bit unsigned value to configure the maximum TX MPDU for
1473 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION
= 8,
1474 /* 8-bit unsigned value to configure the maximum RX MPDU for
1477 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION
= 9,
1478 /* 8-bit unsigned value to configure the Non aggregrate/11g sw
1479 * retry threshold (0 disable, 31 max).
1481 QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY
= 10,
1482 /* 8-bit unsigned value to configure the aggregrate sw
1483 * retry threshold (0 disable, 31 max).
1485 QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY
= 11,
1486 /* 8-bit unsigned value to configure the MGMT frame
1487 * retry threshold (0 disable, 31 max).
1489 QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY
= 12,
1490 /* 8-bit unsigned value to configure the CTRL frame
1491 * retry threshold (0 disable, 31 max).
1493 QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY
= 13,
1494 /* 8-bit unsigned value to configure the propagation delay for
1495 * 2G/5G band (0~63, units in us)
1497 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY
= 14,
1498 /* Unsigned 32-bit value to configure the number of unicast TX fail
1499 * packet count. The peer is disconnected once this threshold is
1502 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT
= 15,
1503 /* Attribute used to set scan default IEs to the driver.
1505 * These IEs can be used by scan operations that will be initiated by
1506 * the driver/firmware.
1508 * For further scan requests coming to the driver, these IEs should be
1509 * merged with the IEs received along with scan request coming to the
1510 * driver. If a particular IE is present in the scan default IEs but not
1511 * present in the scan request, then that IE should be added to the IEs
1512 * sent in the Probe Request frames for that scan request.
1514 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES
= 16,
1515 /* Unsigned 32-bit attribute for generic commands */
1516 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND
= 17,
1517 /* Unsigned 32-bit value attribute for generic commands */
1518 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE
= 18,
1519 /* Unsigned 32-bit data attribute for generic command response */
1520 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
= 19,
1521 /* Unsigned 32-bit length attribute for
1522 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
1524 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH
= 20,
1525 /* Unsigned 32-bit flags attribute for
1526 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
1528 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS
= 21,
1529 /* Unsigned 32-bit, defining the access policy.
1530 * See enum qca_access_policy. Used with
1531 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST.
1533 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY
= 22,
1534 /* Sets the list of full set of IEs for which a specific access policy
1535 * has to be applied. Used along with
1536 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
1537 * Zero length payload can be used to clear this access constraint.
1539 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST
= 23,
1540 /* Unsigned 32-bit, specifies the interface index (netdev) for which the
1541 * corresponding configurations are applied. If the interface index is
1542 * not specified, the configurations are attributed to the respective
1545 QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX
= 24,
1546 /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
1547 QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER
= 25,
1548 /* 8-bit unsigned value to configure the driver and below layers to
1549 * ignore the assoc disallowed set by APs while connecting
1550 * 1-Ignore, 0-Don't ignore
1552 QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED
= 26,
1553 /* 32-bit unsigned value to trigger antenna diversity features:
1554 * 1-Enable, 0-Disable
1556 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA
= 27,
1557 /* 32-bit unsigned value to configure specific chain antenna */
1558 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN
= 28,
1559 /* 32-bit unsigned value to trigger cycle selftest
1560 * 1-Enable, 0-Disable
1562 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST
= 29,
1563 /* 32-bit unsigned to configure the cycle time of selftest
1564 * the unit is micro-second
1566 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL
= 30,
1567 /* 32-bit unsigned value to set reorder timeout for AC_VO */
1568 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE
= 31,
1569 /* 32-bit unsigned value to set reorder timeout for AC_VI */
1570 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO
= 32,
1571 /* 32-bit unsigned value to set reorder timeout for AC_BE */
1572 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT
= 33,
1573 /* 32-bit unsigned value to set reorder timeout for AC_BK */
1574 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND
= 34,
1575 /* 6-byte MAC address to point out the specific peer */
1576 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC
= 35,
1577 /* 32-bit unsigned value to set window size for specific peer */
1578 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT
= 36,
1579 /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */
1580 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24
= 37,
1581 /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */
1582 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5
= 38,
1583 /* 32-bit unsigned value to configure 5 or 10 MHz channel width for
1584 * station device while in disconnect state. The attribute use the
1585 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz,
1586 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or
1587 * 10 MHz channel width, the station will not connect to a BSS using 20
1588 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to
1589 * clear this constraint.
1591 QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH
= 39,
1592 /* 32-bit unsigned value to configure the propagation absolute delay
1593 * for 2G/5G band (units in us)
1595 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY
= 40,
1596 /* 32-bit unsigned value to set probe period */
1597 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD
= 41,
1598 /* 32-bit unsigned value to set stay period */
1599 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD
= 42,
1600 /* 32-bit unsigned value to set snr diff */
1601 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF
= 43,
1602 /* 32-bit unsigned value to set probe dwell time */
1603 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME
= 44,
1604 /* 32-bit unsigned value to set mgmt snr weight */
1605 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT
= 45,
1606 /* 32-bit unsigned value to set data snr weight */
1607 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT
= 46,
1608 /* 32-bit unsigned value to set ack snr weight */
1609 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT
= 47,
1610 /* 32-bit unsigned value to configure the listen interval.
1611 * This is in units of beacon intervals. This configuration alters
1612 * the negotiated listen interval with the AP during the connection.
1613 * It is highly recommended to configure a value less than or equal to
1614 * the one negotiated during the association. Configuring any greater
1615 * value can have adverse effects (frame loss, AP disassociating STA,
1618 QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL
= 48,
1620 * 8 bit unsigned value that is set on an AP/GO virtual interface to
1621 * disable operations that would cause the AP/GO to leave its operating
1624 * This will restrict the scans to the AP/GO operating channel and the
1625 * channels of the other band, if DBS is supported.A STA/CLI interface
1626 * brought up after this setting is enabled, will be restricted to
1627 * connecting to devices only on the AP/GO interface's operating channel
1628 * or on the other band in DBS case. P2P supported channel list is
1629 * modified, to only include AP interface's operating-channel and the
1630 * channels of the other band if DBS is supported.
1632 * These restrictions are only applicable as long as the AP/GO interface
1633 * is alive. If the AP/GO interface is brought down then this
1634 * setting/restriction is forgotten.
1636 * If this variable is set on an AP/GO interface while a multi-channel
1637 * concurrent session is active, it has no effect on the operation of
1638 * the current interfaces, other than restricting the scan to the AP/GO
1639 * operating channel and the other band channels if DBS is supported.
1640 * However, if the STA is brought down and restarted then the new STA
1641 * connection will either be formed on the AP/GO channel or on the
1642 * other band in a DBS case. This is because of the scan being
1643 * restricted on these channels as mentioned above.
1645 * 1-Restrict / 0-Don't restrict offchannel operations.
1647 QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL
= 49,
1649 * 8 bit unsigned value to enable/disable LRO (Large Receive Offload)
1651 * 1 - Enable, 0 - Disable.
1653 QCA_WLAN_VENDOR_ATTR_CONFIG_LRO
= 50,
1656 * 8 bit unsigned value to globally enable/disable scan
1657 * 1 - Enable, 0 - Disable.
1659 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE
= 51,
1661 /* 8-bit unsigned value to set the total beacon miss count
1662 * This parameter will set the total beacon miss count.
1664 QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT
= 52,
1666 /* Unsigned 32-bit value to configure the number of continuous
1667 * Beacon Miss which shall be used by the firmware to penalize
1670 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC
= 53,
1672 /* 8-bit unsigned value to configure the driver and below layers to
1673 * enable/disable all FILS features.
1674 * 0-enable, 1-disable
1676 QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS
= 54,
1678 /* 16-bit unsigned value to configure the level of WLAN latency
1679 * module. See enum qca_wlan_vendor_attr_config_latency_level.
1681 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL
= 55,
1683 /* 8-bit unsigned value indicating the driver to use the RSNE as-is from
1684 * the connect interface. Exclusively used for the scenarios where the
1685 * device is used as a test bed device with special functionality and
1686 * not recommended for production. This helps driver to not validate the
1687 * RSNE passed from user space and thus allow arbitrary IE data to be
1688 * used for testing purposes.
1689 * 1-enable, 0-disable.
1690 * Applications set/reset this configuration. If not reset, this
1691 * parameter remains in use until the driver is unloaded.
1693 QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE
= 56,
1695 /* 8-bit unsigned value to trigger green Tx power saving.
1696 * 1-Enable, 0-Disable
1698 QCA_WLAN_VENDOR_ATTR_CONFIG_GTX
= 57,
1701 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST
,
1702 QCA_WLAN_VENDOR_ATTR_CONFIG_MAX
=
1703 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST
- 1,
1707 * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
1709 enum qca_wlan_vendor_attr_sap_config
{
1710 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID
= 0,
1711 /* 1 - reserved for QCA */
1712 /* List of frequencies on which AP is expected to operate.
1713 * This is irrespective of ACS configuration. This list is a priority
1714 * based one and is looked for before the AP is created to ensure the
1715 * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
1718 QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST
= 2,
1720 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST
,
1721 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX
=
1722 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST
- 1,
1726 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
1727 * conditional channel switch
1729 enum qca_wlan_vendor_attr_sap_conditional_chan_switch
{
1730 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID
= 0,
1731 /* Priority based frequency list (an array of u32 values in host byte
1734 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST
= 1,
1735 /* Status of the conditional switch (u32).
1736 * 0: Success, Non-zero: Failure
1738 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS
= 2,
1740 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST
,
1741 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX
=
1742 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST
- 1,
1746 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
1748 enum qca_wlan_gpio_attr
{
1749 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID
= 0,
1750 /* Unsigned 32-bit attribute for GPIO command */
1751 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND
,
1752 /* Unsigned 32-bit attribute for GPIO PIN number to configure */
1753 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM
,
1754 /* Unsigned 32-bit attribute for GPIO value to configure */
1755 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE
,
1756 /* Unsigned 32-bit attribute for GPIO pull type */
1757 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE
,
1758 /* Unsigned 32-bit attribute for GPIO interrupt mode */
1759 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE
,
1762 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST
,
1763 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX
=
1764 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST
- 1
1768 * qca_wlan_set_qdepth_thresh_attr - Parameters for setting
1769 * MSDUQ depth threshold per peer per tid in the target
1771 * Associated Vendor Command:
1772 * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
1774 enum qca_wlan_set_qdepth_thresh_attr
{
1775 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID
= 0,
1776 /* 6-byte MAC address */
1777 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR
,
1778 /* Unsigned 32-bit attribute for holding the TID */
1779 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID
,
1780 /* Unsigned 32-bit attribute for holding the update mask
1781 * bit 0 - Update high priority msdu qdepth threshold
1782 * bit 1 - Update low priority msdu qdepth threshold
1783 * bit 2 - Update UDP msdu qdepth threshold
1784 * bit 3 - Update Non UDP msdu qdepth threshold
1785 * rest of bits are reserved
1787 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK
,
1788 /* Unsigned 32-bit attribute for holding the threshold value */
1789 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE
,
1792 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST
,
1793 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX
=
1794 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST
- 1,
1798 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
1800 enum qca_wlan_vendor_attr_get_hw_capability
{
1801 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID
,
1802 /* Antenna isolation
1803 * An attribute used in the response.
1804 * The content of this attribute is encoded in a byte array. Each byte
1805 * value is an antenna isolation value. The array length is the number
1808 QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION
,
1809 /* Request HW capability
1810 * An attribute used in the request.
1811 * The content of this attribute is a u32 array for one or more of
1812 * hardware capabilities (attribute IDs) that are being requested. Each
1813 * u32 value has a value from this
1814 * enum qca_wlan_vendor_attr_get_hw_capability
1815 * identifying which capabilities are requested.
1817 QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY
,
1820 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST
,
1821 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX
=
1822 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST
- 1,
1826 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
1827 * offload which is an extension for LL_STATS.
1828 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
1829 * If MAC counters do not exceed the threshold, FW will report monitored
1830 * link layer counters periodically as this setting. The first report is
1831 * always triggered by this timer.
1832 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
1833 * For each MAC layer counter, FW holds two copies. One is the current value.
1834 * The other is the last report. Once a current counter's increment is larger
1835 * than the threshold, FW will indicate that counter to host even if the
1836 * monitoring timer does not expire.
1837 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
1838 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
1839 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
1841 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
1842 * 1: TX packet discarded
1845 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address
1846 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state
1847 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold.
1848 * Threshold for all monitored parameters. If per counter dedicated threshold
1849 * is not enabled, this threshold will take effect.
1850 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this
1851 * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0.
1852 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID
1853 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID
1854 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters
1855 * Bit0: TX counter unit in MSDU
1856 * Bit1: TX counter unit in MPDU
1857 * Bit2: TX counter unit in PPDU
1858 * Bit3: TX counter unit in byte
1859 * Bit4: Dropped MSDUs
1860 * Bit5: Dropped Bytes
1861 * Bit6: MPDU retry counter
1862 * Bit7: MPDU failure counter
1863 * Bit8: PPDU failure counter
1864 * Bit9: MPDU aggregation counter
1865 * Bit10: MCS counter for ACKed MPDUs
1866 * Bit11: MCS counter for Failed MPDUs
1867 * Bit12: TX Delay counter
1868 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters
1869 * Bit0: MAC RX counter unit in MPDU
1870 * Bit1: MAC RX counter unit in byte
1871 * Bit2: PHY RX counter unit in PPDU
1872 * Bit3: PHY RX counter unit in byte
1873 * Bit4: Disorder counter
1874 * Bit5: Retry counter
1875 * Bit6: Duplication counter
1876 * Bit7: Discard counter
1877 * Bit8: MPDU aggregation size counter
1879 * Bit10: Peer STA power state change (wake to sleep) counter
1880 * Bit11: Peer STA power save counter, total time in PS mode
1881 * Bit12: Probe request counter
1882 * Bit13: Other management frames counter
1883 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA
1886 * Bit2: time RX in current bss
1887 * Bit3: Out of current bss time
1888 * Bit4: Wireless medium busy time
1889 * Bit5: RX in bad condition time
1890 * Bit6: TX in bad condition time
1891 * Bit7: time wlan card not available
1892 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal
1893 * Bit0: Per channel SNR counter
1894 * Bit1: Per channel noise floor counter
1895 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers
1896 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels
1897 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats
1898 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats
1899 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats
1900 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs
1901 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs
1902 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs
1903 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data
1904 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets
1905 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped
1906 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK
1907 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed
1908 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed
1909 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM:
1910 * aggregation stats buffer length
1911 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats
1912 * buffer for ACKed MPDUs.
1913 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats
1914 * buffer for failed MPDUs.
1915 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE:
1916 * length of delay stats array.
1917 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats
1918 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs
1919 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs
1920 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats
1921 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received
1922 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received
1923 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received
1924 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received
1925 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost
1926 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets
1927 * flagged as retransmissions
1928 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets
1929 * flagged as duplicated
1930 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX
1932 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation
1934 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs
1936 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer
1937 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer
1938 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep
1939 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time
1940 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe
1942 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt
1944 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time
1945 * there is no TX, nor RX, nor interference.
1946 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time
1947 * transmitting packets.
1948 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time
1950 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time
1951 * interference detected.
1952 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time
1953 * receiving packets with errors.
1954 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time
1956 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time
1957 * the chip is unable to work in normal conditions.
1958 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time
1959 * receiving packets in current BSS.
1960 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time
1961 * receiving packets not in current BSS.
1962 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas
1963 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL:
1964 * This is a container for per antenna signal stats.
1965 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value
1966 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value
1967 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon
1968 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon
1969 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64
1970 * Absolute timestamp from 1970/1/1, unit in ms. After receiving the
1971 * message, user layer APP could call gettimeofday to get another
1972 * timestamp and calculate transfer delay for the message.
1973 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32
1974 * Real period for this measurement, unit in us.
1976 enum qca_wlan_vendor_attr_ll_stats_ext
{
1977 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID
= 0,
1979 /* Attributes for configurations */
1980 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD
,
1981 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD
,
1983 /* Peer STA power state change */
1984 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG
,
1986 /* TX failure event */
1987 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID
,
1988 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU
,
1989 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS
,
1991 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE
,
1992 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS
,
1995 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL
,
1996 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE
,
1997 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID
,
1998 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID
,
1999 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP
,
2000 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP
,
2001 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP
,
2002 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP
,
2003 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM
,
2004 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM
,
2005 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS
,
2006 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER
,
2008 /* Sub-attributes for PEER_AC_TX */
2009 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU
,
2010 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU
,
2011 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU
,
2012 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES
,
2013 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP
,
2014 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES
,
2015 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY
,
2016 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK
,
2017 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK
,
2018 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM
,
2019 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM
,
2020 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM
,
2021 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR
,
2022 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS
,
2023 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS
,
2024 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE
,
2025 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY
,
2027 /* Sub-attributes for PEER_AC_RX */
2028 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU
,
2029 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES
,
2030 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU
,
2031 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES
,
2032 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST
,
2033 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY
,
2034 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP
,
2035 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD
,
2036 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM
,
2037 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM
,
2038 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS
,
2039 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR
,
2040 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES
,
2041 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION
,
2042 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ
,
2043 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT
,
2045 /* Sub-attributes for CCA_BSS */
2046 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME
,
2047 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME
,
2048 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME
,
2049 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY
,
2050 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD
,
2051 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD
,
2052 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL
,
2054 /* sub-attribute for BSS_RX_TIME */
2055 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME
,
2056 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME
,
2058 /* Sub-attributes for PEER_SIGNAL */
2059 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM
,
2060 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL
,
2061 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR
,
2062 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF
,
2064 /* Sub-attributes for IFACE_BSS */
2065 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON
,
2066 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON
,
2068 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME
,
2069 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME
,
2071 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST
,
2072 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX
=
2073 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST
- 1
2076 /* Attributes for FTM commands and events */
2079 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities
2081 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See
2082 * enum qca_wlan_vendor_attr_loc_capa_flags.
2083 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number
2084 * of measurement sessions that can run concurrently.
2085 * Default is one session (no session concurrency).
2086 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique
2087 * peers that are supported in running sessions. For example,
2088 * if the value is 8 and maximum number of sessions is 2, you can
2089 * have one session with 8 unique peers, or 2 sessions with 4 unique
2090 * peers each, and so on.
2091 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number
2092 * of bursts per peer, as an exponent (2^value). Default is 0,
2093 * meaning no multi-burst support.
2094 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number
2095 * of measurement exchanges allowed in a single burst.
2096 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement
2097 * types. A bit mask (unsigned 32 bit value), each bit corresponds
2098 * to an AOA type as defined by enum qca_vendor_attr_aoa_type.
2100 enum qca_wlan_vendor_attr_loc_capa
{
2101 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID
,
2102 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS
,
2103 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS
,
2104 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS
,
2105 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP
,
2106 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST
,
2107 QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES
,
2109 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST
,
2110 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX
=
2111 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST
- 1,
2115 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags
2117 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver
2118 * can be configured as an FTM responder (for example, an AP that
2119 * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
2120 * will be supported if set.
2121 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver
2122 * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
2123 * will be supported if set.
2124 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder
2125 * supports immediate (ASAP) response.
2126 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone
2127 * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS.
2128 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports
2129 * requesting AOA measurements as part of an FTM session.
2131 enum qca_wlan_vendor_attr_loc_capa_flags
{
2132 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER
= 1 << 0,
2133 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR
= 1 << 1,
2134 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP
= 1 << 2,
2135 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA
= 1 << 3,
2136 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM
= 1 << 4,
2140 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about
2141 * a single peer in a measurement session.
2143 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer.
2144 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related
2145 * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags.
2146 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of
2147 * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0
2148 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for
2149 * list of supported attributes.
2150 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for
2151 * secure measurement.
2152 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA
2153 * measurement every <value> bursts. If 0 or not specified,
2154 * AOA measurements will be disabled for this peer.
2155 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where
2156 * the measurement frames are exchanged. Optional; if not
2157 * specified, try to locate the peer in the kernel scan
2158 * results cache and use frequency from there.
2160 enum qca_wlan_vendor_attr_ftm_peer_info
{
2161 QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID
,
2162 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR
,
2163 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS
,
2164 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS
,
2165 QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID
,
2166 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD
,
2167 QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ
,
2169 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST
,
2170 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX
=
2171 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST
- 1,
2175 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags,
2178 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request
2179 * immediate (ASAP) response from peer.
2180 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request
2181 * LCI report from peer. The LCI report includes the absolute
2182 * location of the peer in "official" coordinates (similar to GPS).
2183 * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information.
2184 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request
2185 * Location civic report from peer. The LCR includes the location
2186 * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0,
2187 * 11.24.6.7 for more information.
2188 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set,
2189 * request a secure measurement.
2190 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided.
2192 enum qca_wlan_vendor_attr_ftm_peer_meas_flags
{
2193 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP
= 1 << 0,
2194 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI
= 1 << 1,
2195 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR
= 1 << 2,
2196 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE
= 1 << 3,
2200 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters
2202 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements
2203 * to perform in a single burst.
2204 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to
2205 * perform, specified as an exponent (2^value).
2206 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst
2207 * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167.
2208 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts,
2209 * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must
2210 * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION.
2212 enum qca_wlan_vendor_attr_ftm_meas_param
{
2213 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID
,
2214 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST
,
2215 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP
,
2216 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION
,
2217 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD
,
2219 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST
,
2220 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX
=
2221 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST
- 1,
2225 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results
2227 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported
2229 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement
2230 * request for this peer.
2231 * See enum qca_wlan_vendor_attr_ftm_peer_result_status.
2232 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related
2233 * to measurement results for this peer.
2234 * See enum qca_wlan_vendor_attr_ftm_peer_result_flags.
2235 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when
2236 * request failed and peer requested not to send an additional request
2237 * for this number of seconds.
2238 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received
2239 * from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
2241 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when
2242 * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
2244 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer
2245 * overridden some measurement request parameters. See
2246 * enum qca_wlan_vendor_attr_ftm_meas_param.
2247 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement
2248 * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
2249 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement
2250 * results. Each entry is a nested attribute defined
2251 * by enum qca_wlan_vendor_attr_ftm_meas.
2253 enum qca_wlan_vendor_attr_ftm_peer_result
{
2254 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID
,
2255 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR
,
2256 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS
,
2257 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS
,
2258 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
,
2259 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI
,
2260 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR
,
2261 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS
,
2262 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS
,
2263 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS
,
2265 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST
,
2266 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX
=
2267 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST
- 1,
2271 * enum qca_wlan_vendor_attr_ftm_peer_result_status
2273 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results
2274 * will be provided. Peer may have overridden some measurement parameters,
2275 * in which case overridden parameters will be report by
2276 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute.
2277 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable
2278 * of performing the measurement request. No more results will be sent
2279 * for this peer in this session.
2280 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request
2281 * failed, and requested not to send an additional request for number
2282 * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
2284 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation
2285 * failed. Request was not sent over the air.
2287 enum qca_wlan_vendor_attr_ftm_peer_result_status
{
2288 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK
,
2289 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE
,
2290 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED
,
2291 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID
,
2295 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags
2296 * for measurement result, per-peer
2298 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set,
2299 * measurement completed for this peer. No more results will be reported
2300 * for this peer in this session.
2302 enum qca_wlan_vendor_attr_ftm_peer_result_flags
{
2303 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE
= 1 << 0,
2307 * enum qca_vendor_attr_loc_session_status: Session completion status code
2309 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed
2311 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted
2313 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request
2314 * was invalid and was not started.
2315 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error
2316 * and did not complete normally (for example out of resources).
2318 enum qca_vendor_attr_loc_session_status
{
2319 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK
,
2320 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED
,
2321 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID
,
2322 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED
,
2326 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data
2328 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as
2329 * recorded by responder, in picoseconds.
2330 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2331 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at
2332 * initiator, in picoseconds.
2333 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2334 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by
2335 * initiator, in picoseconds.
2336 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2337 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at
2338 * responder, in picoseconds.
2339 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2340 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded
2341 * during this measurement exchange. Optional and will be provided if
2342 * the hardware can measure it.
2343 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by
2344 * responder. Not always provided.
2345 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2346 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by
2347 * responder. Not always provided.
2348 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2349 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by
2350 * initiator. Not always provided.
2351 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2352 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by
2353 * initiator. Not always provided.
2354 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2355 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding.
2357 enum qca_wlan_vendor_attr_ftm_meas
{
2358 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID
,
2359 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1
,
2360 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2
,
2361 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3
,
2362 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4
,
2363 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI
,
2364 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR
,
2365 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR
,
2366 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR
,
2367 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR
,
2368 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD
,
2370 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST
,
2371 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX
=
2372 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST
- 1,
2376 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type
2378 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest
2379 * CIR (channel impulse response) path for each antenna.
2380 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude
2381 * of the strongest CIR path for each antenna.
2383 enum qca_wlan_vendor_attr_aoa_type
{
2384 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE
,
2385 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP
,
2386 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX
2390 * enum qca_wlan_vendor_attr_encryption_test - Attributes to
2391 * validate encryption engine
2393 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute.
2394 * This will be included if the request is for decryption; if not included,
2395 * the request is treated as a request for encryption by default.
2396 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value
2397 * indicating the key cipher suite. Takes same values as
2398 * NL80211_ATTR_KEY_CIPHER.
2399 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value
2400 * Key Id to be used for encryption
2401 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values.
2402 * Key (TK) to be used for encryption/decryption
2403 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values.
2404 * Packet number to be specified for encryption/decryption
2405 * 6 bytes for TKIP/CCMP/GCMP.
2406 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values
2407 * representing the 802.11 packet (header + payload + FCS) that
2408 * needs to be encrypted/decrypted.
2409 * Encrypted/decrypted response from the driver will also be sent
2410 * to userspace with the same attribute.
2412 enum qca_wlan_vendor_attr_encryption_test
{
2413 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID
= 0,
2414 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION
,
2415 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER
,
2416 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID
,
2417 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK
,
2418 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN
,
2419 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA
,
2422 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST
,
2423 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX
=
2424 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST
- 1
2428 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of
2429 * sector for DMG RF sector operations.
2431 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector
2432 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector
2434 enum qca_wlan_vendor_attr_dmg_rf_sector_type
{
2435 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX
,
2436 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX
,
2437 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX
2441 * BRP antenna limit mode
2443 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force
2444 * antenna limit, BRP will be performed as usual.
2445 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal
2446 * antennas limit. the hardware may use less antennas than the
2448 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will
2449 * use exactly the specified number of antennas for BRP.
2451 enum qca_wlan_vendor_attr_brp_ant_limit_mode
{
2452 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE
,
2453 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE
,
2454 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE
,
2455 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX
2459 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for
2460 * DMG RF sector configuration for a single RF module.
2461 * The values are defined in a compact way which closely matches
2462 * the way it is stored in HW registers.
2463 * The configuration provides values for 32 antennas and 8 distribution
2464 * amplifiers, and together describes the characteristics of the RF
2465 * sector - such as a beam in some direction with some gain.
2467 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index
2468 * of RF module for this configuration.
2469 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge
2470 * amplifier gain index. Unsigned 32 bit number containing
2471 * bits for all 32 antennas.
2472 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge
2473 * amplifier gain index. Unsigned 32 bit number containing
2474 * bits for all 32 antennas.
2475 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge
2476 * amplifier gain index. Unsigned 32 bit number containing
2477 * bits for all 32 antennas.
2478 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values
2479 * for first 16 antennas, 2 bits per antenna.
2480 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values
2481 * for last 16 antennas, 2 bits per antenna.
2482 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains
2483 * DTYPE values (3 bits) for each distribution amplifier, followed
2484 * by X16 switch bits for each distribution amplifier. There are
2485 * total of 8 distribution amplifiers.
2487 enum qca_wlan_vendor_attr_dmg_rf_sector_cfg
{
2488 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID
= 0,
2489 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX
= 1,
2490 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0
= 2,
2491 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1
= 3,
2492 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2
= 4,
2493 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI
= 5,
2494 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO
= 6,
2495 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16
= 7,
2498 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST
,
2499 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX
=
2500 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST
- 1
2503 enum qca_wlan_vendor_attr_ll_stats_set
{
2504 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID
= 0,
2505 /* Unsigned 32-bit value */
2506 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD
= 1,
2507 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING
= 2,
2509 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST
,
2510 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX
=
2511 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST
- 1,
2514 enum qca_wlan_vendor_attr_ll_stats_clr
{
2515 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID
= 0,
2516 /* Unsigned 32bit bitmap for clearing statistics
2517 * All radio statistics 0x00000001
2518 * cca_busy_time (within radio statistics) 0x00000002
2519 * All channel stats (within radio statistics) 0x00000004
2520 * All scan statistics (within radio statistics) 0x00000008
2521 * All interface statistics 0x00000010
2522 * All tx rate statistics (within interface statistics) 0x00000020
2523 * All ac statistics (with in interface statistics) 0x00000040
2524 * All contention (min, max, avg) statistics (within ac statisctics)
2527 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK
= 1,
2528 /* Unsigned 8 bit value: Request to stop statistics collection */
2529 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ
= 2,
2531 /* Unsigned 32 bit bitmap: Response from the driver
2532 * for the cleared statistics
2534 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK
= 3,
2535 /* Unsigned 8 bit value: Response from driver/firmware
2536 * for the stop request
2538 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP
= 4,
2540 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST
,
2541 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX
=
2542 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST
- 1,
2545 enum qca_wlan_vendor_attr_ll_stats_get
{
2546 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID
= 0,
2547 /* Unsigned 32 bit value provided by the caller issuing the GET stats
2548 * command. When reporting the stats results, the driver uses the same
2549 * value to indicate which GET request the results correspond to.
2551 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID
= 1,
2552 /* Unsigned 32 bit value - bit mask to identify what statistics are
2553 * requested for retrieval.
2554 * Radio Statistics 0x00000001
2555 * Interface Statistics 0x00000020
2556 * All Peer Statistics 0x00000040
2557 * Peer Statistics 0x00000080
2559 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK
= 2,
2561 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST
,
2562 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX
=
2563 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST
- 1,
2566 enum qca_wlan_vendor_attr_ll_stats_results
{
2567 QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID
= 0,
2568 /* Unsigned 32bit value. Used by the driver; must match the request id
2569 * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command.
2571 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID
= 1,
2573 /* Unsigned 32 bit value */
2574 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX
= 2,
2575 /* Unsigned 32 bit value */
2576 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX
= 3,
2577 /* Unsigned 32 bit value */
2578 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX
= 4,
2579 /* Unsigned 32 bit value */
2580 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX
= 5,
2581 /* Signed 32 bit value */
2582 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT
= 6,
2583 /* Signed 32 bit value */
2584 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA
= 7,
2585 /* Signed 32 bit value */
2586 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK
= 8,
2588 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are
2589 * nested within the interface stats.
2592 /* Interface mode, e.g., STA, SOFTAP, IBSS, etc.
2593 * Type = enum wifi_interface_mode.
2595 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE
= 9,
2596 /* Interface MAC address. An array of 6 Unsigned int8 */
2597 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR
= 10,
2598 /* Type = enum wifi_connection_state, e.g., DISCONNECTED,
2599 * AUTHENTICATING, etc. valid for STA, CLI only.
2601 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE
= 11,
2602 /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE
2604 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING
= 12,
2605 /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */
2606 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES
= 13,
2607 /* NULL terminated SSID. An array of 33 Unsigned 8bit values */
2608 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID
= 14,
2609 /* BSSID. An array of 6 unsigned 8 bit values */
2610 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID
= 15,
2611 /* Country string advertised by AP. An array of 3 unsigned 8 bit
2614 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR
= 16,
2615 /* Country string for this association. An array of 3 unsigned 8 bit
2618 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR
= 17,
2620 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could
2621 * be nested within the interface stats.
2624 /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */
2625 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC
= 18,
2626 /* Unsigned int 32 value corresponding to respective AC */
2627 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU
= 19,
2628 /* Unsigned int 32 value corresponding to respective AC */
2629 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU
= 20,
2630 /* Unsigned int 32 value corresponding to respective AC */
2631 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST
= 21,
2632 /* Unsigned int 32 value corresponding to respective AC */
2633 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST
= 22,
2634 /* Unsigned int 32 value corresponding to respective AC */
2635 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU
= 23,
2636 /* Unsigned int 32 value corresponding to respective AC */
2637 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU
= 24,
2638 /* Unsigned int 32 value corresponding to respective AC */
2639 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST
= 25,
2640 /* Unsigned int 32 value corresponding to respective AC */
2641 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES
= 26,
2642 /* Unsigned int 32 value corresponding to respective AC */
2643 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT
= 27,
2644 /* Unsigned int 32 values corresponding to respective AC */
2645 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG
= 28,
2646 /* Unsigned int 32 values corresponding to respective AC */
2647 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN
= 29,
2648 /* Unsigned int 32 values corresponding to respective AC */
2649 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX
= 30,
2650 /* Unsigned int 32 values corresponding to respective AC */
2651 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG
= 31,
2652 /* Unsigned int 32 values corresponding to respective AC */
2653 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES
= 32,
2654 /* Unsigned 32 bit value. Number of peers */
2655 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS
= 33,
2657 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are
2658 * nested within the interface stats.
2661 /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */
2662 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE
= 34,
2663 /* MAC addr corresponding to respective peer. An array of 6 unsigned
2666 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS
= 35,
2667 /* Unsigned int 32 bit value representing capabilities corresponding
2668 * to respective peer.
2670 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES
= 36,
2671 /* Unsigned 32 bit value. Number of rates */
2672 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES
= 37,
2674 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
2675 * are nested within the rate stat.
2678 /* Wi-Fi Rate - separate attributes defined for individual fields */
2680 /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */
2681 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE
= 38,
2682 /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */
2683 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS
= 39,
2684 /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */
2685 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW
= 40,
2686 /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std
2687 * in the units of 0.5 Mbps HT/VHT it would be MCS index
2689 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX
= 41,
2691 /* Unsigned 32 bit value. Bit rate in units of 100 kbps */
2692 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE
= 42,
2694 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be
2695 * nested within the peer info stats.
2698 /* Unsigned int 32 bit value. Number of successfully transmitted data
2699 * packets, i.e., with ACK received corresponding to the respective
2702 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU
= 43,
2703 /* Unsigned int 32 bit value. Number of received data packets
2704 * corresponding to the respective rate.
2706 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU
= 44,
2707 /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK
2708 * received corresponding to the respective rate.
2710 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST
= 45,
2711 /* Unsigned int 32 bit value. Total number of data packet retries for
2712 * the respective rate.
2714 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES
= 46,
2715 /* Unsigned int 32 bit value. Total number of short data packet retries
2716 * for the respective rate.
2718 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT
= 47,
2719 /* Unsigned int 32 bit value. Total number of long data packet retries
2720 * for the respective rate.
2722 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG
= 48,
2724 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID
= 49,
2725 /* Unsigned 32 bit value. Total number of msecs the radio is awake
2726 * accruing over time.
2728 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME
= 50,
2729 /* Unsigned 32 bit value. Total number of msecs the radio is
2730 * transmitting accruing over time.
2732 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME
= 51,
2733 /* Unsigned 32 bit value. Total number of msecs the radio is in active
2734 * receive accruing over time.
2736 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME
= 52,
2737 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2738 * to all scan accruing over time.
2740 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN
= 53,
2741 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2742 * to NAN accruing over time.
2744 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD
= 54,
2745 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2746 * to GSCAN accruing over time.
2748 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN
= 55,
2749 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2750 * to roam scan accruing over time.
2752 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN
= 56,
2753 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2754 * to PNO scan accruing over time.
2756 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN
= 57,
2757 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2758 * to Hotspot 2.0 scans and GAS exchange accruing over time.
2760 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20
= 58,
2761 /* Unsigned 32 bit value. Number of channels. */
2762 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS
= 59,
2764 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could
2765 * be nested within the channel stats.
2768 /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */
2769 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH
= 60,
2770 /* Unsigned 32 bit value. Primary 20 MHz channel. */
2771 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ
= 61,
2772 /* Unsigned 32 bit value. Center frequency (MHz) first segment. */
2773 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0
= 62,
2774 /* Unsigned 32 bit value. Center frequency (MHz) second segment. */
2775 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1
= 63,
2777 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be
2778 * nested within the radio stats.
2781 /* Unsigned int 32 bit value representing total number of msecs the
2782 * radio is awake on that channel accruing over time, corresponding to
2783 * the respective channel.
2785 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME
= 64,
2786 /* Unsigned int 32 bit value representing total number of msecs the CCA
2787 * register is busy accruing over time corresponding to the respective
2790 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME
= 65,
2792 QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS
= 66,
2794 /* Signifies the nested list of channel attributes
2795 * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_*
2797 QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO
= 67,
2799 /* Signifies the nested list of peer info attributes
2800 * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*
2802 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO
= 68,
2804 /* Signifies the nested list of rate info attributes
2805 * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
2807 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO
= 69,
2809 /* Signifies the nested list of wmm info attributes
2810 * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_*
2812 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO
= 70,
2814 /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates
2815 * that more stats, e.g., peers or radio, are to follow in the next
2816 * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event.
2817 * Otherwise, it is set to 0.
2819 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA
= 71,
2821 /* Unsigned 64 bit value */
2822 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET
= 72,
2824 /* Unsigned 32 bit value */
2825 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED
= 73,
2827 /* Unsigned 32 bit value */
2828 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED
= 74,
2830 /* Unsigned 32 bit value */
2831 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME
= 75,
2833 /* Unsigned 32 bit value */
2834 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE
= 76,
2836 /* Unsigned 32 bit value */
2837 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS
= 77,
2839 /* Number of msecs the radio spent in transmitting for each power level
2841 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL
= 78,
2843 /* Unsigned 32 bit value */
2844 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT
= 79,
2845 /* Unsigned 32 bit value */
2846 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT
= 80,
2847 /* Unsigned 32 bit value */
2848 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT
= 81,
2849 /* Unsigned 32 bit value */
2850 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT
= 82,
2852 /* Unsigned int 32 value.
2853 * Pending MSDUs corresponding to respective AC.
2855 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU
= 83,
2858 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST
,
2859 QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX
=
2860 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST
- 1,
2863 enum qca_wlan_vendor_attr_ll_stats_type
{
2864 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID
= 0,
2865 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO
= 1,
2866 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE
= 2,
2867 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS
= 3,
2870 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST
,
2871 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX
=
2872 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST
- 1,
2876 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for
2877 * TDLS configuration to the host driver.
2879 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger
2880 * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode
2881 * represents the different TDLS trigger modes.
2882 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within
2883 * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number
2884 * of packets shall meet the criteria for implicit TDLS setup.
2885 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets
2886 * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
2887 * to initiate a TDLS setup.
2888 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate
2889 * a TDLS Discovery to the peer.
2890 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of
2891 * discovery attempts to know the TDLS capability of the peer. A peer is
2892 * marked as TDLS not capable if there is no response for all the attempts.
2893 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32)
2894 * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
2895 * number of TX / RX frames meet the criteria for TDLS teardown.
2896 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32)
2897 * of Tx/Rx packets within a duration
2898 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link.
2899 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold
2900 * corresponding to the RSSI of the peer below which a TDLS setup is
2902 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold
2903 * corresponding to the RSSI of the peer above which a TDLS teardown is
2906 enum qca_wlan_vendor_attr_tdls_configuration
{
2907 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID
= 0,
2908 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE
= 1,
2910 /* Attributes configuring the TDLS Implicit Trigger */
2911 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
= 2,
2912 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD
= 3,
2913 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD
= 4,
2914 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT
= 5,
2915 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT
= 6,
2916 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
= 7,
2917 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD
= 8,
2918 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD
= 9,
2921 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST
,
2922 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX
=
2923 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST
- 1
2927 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in
2930 * The following are the different values for
2931 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE.
2933 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown
2934 * the TDLS connection to a respective peer comes from the user space.
2935 * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN,
2936 * TDLS_DISCOVER to do this.
2937 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS
2938 * setup/teardown to the eligible peer once the configured criteria
2939 * (such as TX/RX threshold, RSSI) is met. The attributes
2940 * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to
2941 * the different configuration criteria for the TDLS trigger from the
2943 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger
2944 * the TDLS setup / teardown through the implicit mode only to the
2945 * configured MAC addresses (wpa_supplicant, with tdls_external_control=1,
2946 * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands).
2947 * External mode works on top of the implicit mode. Thus the host driver
2948 * is expected to configure in TDLS Implicit mode too to operate in
2950 * Configuring External mode alone without Implicit mode is invalid.
2952 * All the above implementations work as expected only when the host driver
2953 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing
2954 * that the TDLS message exchange is not internal to the host driver, but
2955 * depends on wpa_supplicant to do the message exchange.
2957 enum qca_wlan_vendor_tdls_trigger_mode
{
2958 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT
= 1 << 0,
2959 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT
= 1 << 1,
2960 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL
= 1 << 2,
2964 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
2965 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
2966 * that is hard-coded in the Board Data File (BDF).
2967 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
2968 * that is hard-coded in the Board Data File (BDF).
2969 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
2970 * that is hard-coded in the Board Data File (BDF).
2971 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
2972 * that is hard-coded in the Board Data File (BDF).
2973 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
2974 * that is hard-coded in the Board Data File (BDF).
2975 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
2976 * source of SAR power limits, thereby disabling the SAR power
2978 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
2979 * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
2980 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power
2981 * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
2983 * This enumerates the valid set of values that may be supplied for
2984 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
2985 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in
2986 * the response to an instance of the
2987 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
2989 enum qca_vendor_attr_sar_limits_selections
{
2990 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0
= 0,
2991 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1
= 1,
2992 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2
= 2,
2993 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3
= 3,
2994 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4
= 4,
2995 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE
= 5,
2996 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER
= 6,
2997 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0
= 7,
3001 * enum qca_vendor_attr_sar_limits_spec_modulations -
3002 * SAR limits specification modulation
3003 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
3005 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
3008 * This enumerates the valid set of values that may be supplied for
3009 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
3010 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
3011 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
3012 * command or in the response to an instance of the
3013 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
3015 enum qca_vendor_attr_sar_limits_spec_modulations
{
3016 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK
= 0,
3017 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM
= 1,
3021 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
3023 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to
3024 * select which SAR power limit table should be used. Valid
3025 * values are enumerated in enum
3026 * %qca_vendor_attr_sar_limits_selections. The existing SAR
3027 * power limit selection is unchanged if this attribute is not
3030 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
3031 * which specifies the number of SAR power limit specifications
3032 * which will follow.
3034 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
3035 * limit specifications. The number of specifications is
3036 * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
3037 * specification contains a set of
3038 * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
3039 * specification is uniquely identified by the attributes
3040 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
3041 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
3042 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
3043 * contains as a payload the attribute
3044 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT,
3045 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX.
3046 * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or
3047 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is
3048 * needed based upon the value of
3049 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE.
3051 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
3052 * indicate for which band this specification applies. Valid
3053 * values are enumerated in enum %nl80211_band (although not all
3054 * bands may be supported by a given device). If the attribute is
3055 * not supplied then the specification will be applied to all
3058 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
3059 * to indicate for which antenna chain this specification
3060 * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
3061 * attribute is not supplied then the specification will be
3062 * applied to all chains.
3064 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
3065 * value to indicate for which modulation scheme this
3066 * specification applies. Valid values are enumerated in enum
3067 * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
3068 * is not supplied then the specification will be applied to all
3069 * modulation schemes.
3071 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
3072 * value to specify the actual power limit value in units of 0.5
3073 * dBm (i.e., a value of 11 represents 5.5 dBm).
3074 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
3075 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER.
3077 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32)
3078 * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles.
3079 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
3080 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0.
3082 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
3083 * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS.
3085 enum qca_vendor_attr_sar_limits
{
3086 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID
= 0,
3087 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE
= 1,
3088 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS
= 2,
3089 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC
= 3,
3090 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND
= 4,
3091 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN
= 5,
3092 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION
= 6,
3093 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT
= 7,
3094 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX
= 8,
3096 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST
,
3097 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX
=
3098 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST
- 1
3102 * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
3103 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
3105 enum qca_wlan_vendor_attr_get_wifi_info
{
3106 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID
= 0,
3107 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION
= 1,
3108 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION
= 2,
3111 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST
,
3112 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX
=
3113 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST
- 1,
3117 * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by
3118 * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command.
3120 enum qca_wlan_vendor_attr_wifi_logger_start
{
3121 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID
= 0,
3122 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID
= 1,
3123 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL
= 2,
3124 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS
= 3,
3127 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST
,
3128 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX
=
3129 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST
- 1,
3132 enum qca_wlan_vendor_attr_logger_results
{
3133 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID
= 0,
3135 /* Unsigned 32-bit value; must match the request Id supplied by
3136 * Wi-Fi HAL in the corresponding subcmd NL msg.
3138 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID
= 1,
3140 /* Unsigned 32-bit value; used to indicate the size of memory
3141 * dump to be allocated.
3143 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE
= 2,
3146 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST
,
3147 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX
=
3148 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST
- 1,
3151 enum qca_wlan_vendor_attr_roaming_config_params
{
3152 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID
= 0,
3154 QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD
= 1,
3155 QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID
= 2,
3157 /* Attributes for wifi_set_ssid_white_list */
3158 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS
= 3,
3159 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST
= 4,
3160 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID
= 5,
3162 /* Attributes for set_roam_params */
3163 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD
= 6,
3164 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD
= 7,
3165 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR
= 8,
3166 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR
= 9,
3167 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST
= 10,
3168 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS
= 11,
3169 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER
= 12,
3171 /* Attribute for set_lazy_roam */
3172 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE
= 13,
3174 /* Attribute for set_lazy_roam with preferences */
3175 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS
= 14,
3176 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID
= 15,
3177 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID
= 16,
3178 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER
= 17,
3180 /* Attribute for set_blacklist bssid params */
3181 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS
= 18,
3182 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID
= 19,
3183 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID
= 20,
3186 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST
,
3187 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX
=
3188 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST
- 1,
3192 * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
3193 * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
3195 enum qca_wlan_vendor_attr_roam_subcmd
{
3196 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID
= 0,
3197 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST
= 1,
3198 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS
= 2,
3199 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM
= 3,
3200 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS
= 4,
3201 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS
= 5,
3202 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID
= 6,
3205 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST
,
3206 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX
=
3207 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST
- 1,
3210 enum qca_wlan_vendor_attr_gscan_config_params
{
3211 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID
= 0,
3213 /* Unsigned 32-bit value */
3214 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID
= 1,
3216 /* Attributes for data used by
3217 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command.
3219 /* Unsigned 32-bit value */
3220 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND
3222 /* Unsigned 32-bit value */
3223 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS
3226 /* Attributes for input params used by
3227 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command.
3230 /* Unsigned 32-bit value; channel frequency */
3231 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL
= 4,
3232 /* Unsigned 32-bit value; dwell time in ms. */
3233 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME
= 5,
3234 /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */
3235 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE
= 6,
3236 /* Unsigned 8-bit value; channel class */
3237 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS
= 7,
3239 /* Unsigned 8-bit value; bucket index, 0 based */
3240 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX
= 8,
3241 /* Unsigned 8-bit value; band. */
3242 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND
= 9,
3243 /* Unsigned 32-bit value; desired period, in ms. */
3244 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD
= 10,
3245 /* Unsigned 8-bit value; report events semantics. */
3246 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS
= 11,
3247 /* Unsigned 32-bit value. Followed by a nested array of
3248 * GSCAN_CHANNEL_SPEC_* attributes.
3250 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
= 12,
3252 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes.
3253 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
3255 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC
= 13,
3257 /* Unsigned 32-bit value; base timer period in ms. */
3258 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD
= 14,
3259 /* Unsigned 32-bit value; number of APs to store in each scan in the
3260 * BSSID/RSSI history buffer (keep the highest RSSI APs).
3262 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN
= 15,
3263 /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake
3266 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT
3269 /* Unsigned 8-bit value; number of scan bucket specs; followed by a
3270 * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size
3271 * of the array is determined by NUM_BUCKETS.
3273 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
= 17,
3275 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes.
3276 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
3278 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC
= 18,
3280 /* Unsigned 8-bit value */
3281 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH
3283 /* Unsigned 32-bit value; maximum number of results to be returned. */
3284 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX
3287 /* An array of 6 x unsigned 8-bit value */
3288 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID
= 21,
3289 /* Signed 32-bit value */
3290 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW
= 22,
3291 /* Signed 32-bit value */
3292 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH
= 23,
3293 /* Unsigned 32-bit value */
3294 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL
= 24,
3296 /* Number of hotlist APs as unsigned 32-bit value, followed by a nested
3297 * array of AP_THRESHOLD_PARAM attributes and values. The size of the
3298 * array is determined by NUM_AP.
3300 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP
= 25,
3302 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes.
3303 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
3305 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM
= 26,
3307 /* Unsigned 32-bit value; number of samples for averaging RSSI. */
3308 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE
3310 /* Unsigned 32-bit value; number of samples to confirm AP loss. */
3311 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE
3313 /* Unsigned 32-bit value; number of APs breaching threshold. */
3314 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING
= 29,
3315 /* Unsigned 32-bit value; number of APs. Followed by an array of
3316 * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP.
3318 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP
= 30,
3319 /* Unsigned 32-bit value; number of samples to confirm AP loss. */
3320 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE
3322 /* Unsigned 32-bit value. If max_period is non zero or different than
3323 * period, then this bucket is an exponential backoff bucket.
3325 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD
= 32,
3326 /* Unsigned 32-bit value. */
3327 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE
= 33,
3328 /* Unsigned 32-bit value. For exponential back off bucket, number of
3329 * scans to perform for a given period.
3331 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT
= 34,
3332 /* Unsigned 8-bit value; in number of scans, wake up AP after these
3335 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS
3338 /* Attributes for data used by
3339 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command.
3341 /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */
3342 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE
3344 /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a
3345 * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The
3346 * size of the array is determined by NUM_SSID.
3348 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
= 37,
3349 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_*
3351 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
3353 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM
= 38,
3355 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
3356 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID
= 39,
3357 /* Unsigned 8-bit value */
3358 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND
= 40,
3359 /* Signed 32-bit value */
3360 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW
= 41,
3361 /* Signed 32-bit value */
3362 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH
= 42,
3363 /* Unsigned 32-bit value; a bitmask with additional gscan config flag.
3365 QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS
= 43,
3368 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST
,
3369 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX
=
3370 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST
- 1,
3373 enum qca_wlan_vendor_attr_gscan_results
{
3374 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID
= 0,
3376 /* Unsigned 32-bit value; must match the request Id supplied by
3377 * Wi-Fi HAL in the corresponding subcmd NL msg.
3379 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID
= 1,
3381 /* Unsigned 32-bit value; used to indicate the status response from
3382 * firmware/driver for the vendor sub-command.
3384 QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS
= 2,
3386 /* GSCAN Valid Channels attributes */
3387 /* Unsigned 32bit value; followed by a nested array of CHANNELS. */
3388 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS
= 3,
3389 /* An array of NUM_CHANNELS x unsigned 32-bit value integers
3390 * representing channel numbers.
3392 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS
= 4,
3394 /* GSCAN Capabilities attributes */
3395 /* Unsigned 32-bit value */
3396 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE
= 5,
3397 /* Unsigned 32-bit value */
3398 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS
= 6,
3399 /* Unsigned 32-bit value */
3400 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN
3402 /* Unsigned 32-bit value */
3403 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE
3405 /* Signed 32-bit value */
3406 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD
3408 /* Unsigned 32-bit value */
3409 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS
= 10,
3410 /* Unsigned 32-bit value */
3411 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS
3413 /* Unsigned 32-bit value */
3414 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES
3417 /* GSCAN Attributes used with
3418 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command.
3421 /* Unsigned 32-bit value */
3422 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
= 13,
3424 /* GSCAN attributes used with
3425 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command.
3428 /* An array of NUM_RESULTS_AVAILABLE x
3429 * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_*
3431 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST
= 14,
3433 /* Unsigned 64-bit value; age of sample at the time of retrieval */
3434 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP
= 15,
3435 /* 33 x unsigned 8-bit value; NULL terminated SSID */
3436 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID
= 16,
3437 /* An array of 6 x unsigned 8-bit value */
3438 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID
= 17,
3439 /* Unsigned 32-bit value; channel frequency in MHz */
3440 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL
= 18,
3441 /* Signed 32-bit value */
3442 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI
= 19,
3443 /* Unsigned 32-bit value */
3444 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT
= 20,
3445 /* Unsigned 32-bit value */
3446 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD
= 21,
3447 /* Unsigned 16-bit value */
3448 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD
= 22,
3449 /* Unsigned 16-bit value */
3450 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY
= 23,
3451 /* Unsigned 32-bit value; size of the IE DATA blob */
3452 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH
= 24,
3453 /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the
3454 * information elements found in the beacon; this data should be a
3455 * packed list of wifi_information_element objects, one after the
3458 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA
= 25,
3460 /* Unsigned 8-bit value; set by driver to indicate more scan results are
3463 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA
= 26,
3465 /* GSCAN attributes for
3466 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command.
3468 /* Unsigned 8-bit value */
3469 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE
= 27,
3470 /* Unsigned 32-bit value */
3471 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS
= 28,
3473 /* GSCAN attributes for
3474 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command.
3476 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
3477 * to indicate number of results.
3478 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
3482 /* GSCAN attributes for
3483 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command.
3485 /* An array of 6 x unsigned 8-bit value */
3486 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID
= 29,
3487 /* Unsigned 32-bit value */
3488 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL
3490 /* Unsigned 32-bit value. */
3491 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI
3493 /* A nested array of signed 32-bit RSSI values. Size of the array is
3494 * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI.
3496 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST
3499 /* GSCAN attributes used with
3500 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command.
3502 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
3503 * to indicate number of gscan cached results returned.
3504 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate
3505 * the list of gscan cached results.
3508 /* An array of NUM_RESULTS_AVAILABLE x
3509 * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_*
3511 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST
= 33,
3512 /* Unsigned 32-bit value; a unique identifier for the scan unit. */
3513 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID
= 34,
3514 /* Unsigned 32-bit value; a bitmask w/additional information about scan.
3516 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS
= 35,
3517 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
3518 * to indicate number of wifi scan results/bssids retrieved by the scan.
3519 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
3520 * list of wifi scan results returned for each cached result block.
3523 /* GSCAN attributes for
3524 * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command.
3526 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for
3527 * number of results.
3528 * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
3529 * list of wifi scan results returned for each
3530 * wifi_passpoint_match_result block.
3531 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE.
3534 /* GSCAN attributes for
3535 * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command.
3537 /* Unsigned 32-bit value */
3538 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES
3540 /* A nested array of
3541 * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_*
3542 * attributes. Array size =
3543 * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES.
3545 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST
= 37,
3547 /* Unsigned 32-bit value; network block id for the matched network */
3548 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID
= 38,
3549 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
3550 * list of wifi scan results returned for each
3551 * wifi_passpoint_match_result block.
3553 /* Unsigned 32-bit value */
3554 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN
= 39,
3555 /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values;
3556 * ANQP data in the information_element format.
3558 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP
= 40,
3560 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3561 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS
= 41,
3562 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3563 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS
= 42,
3564 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3565 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID
3567 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3568 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID
3571 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED
= 45,
3573 /* Unsigned 32-bit value; a GSCAN Capabilities attribute.
3574 * This is used to limit the maximum number of BSSIDs while sending
3575 * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with attributes
3576 * QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID and
3577 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID.
3579 QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID
= 46,
3582 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST
,
3583 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX
=
3584 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST
- 1,
3587 enum qca_wlan_vendor_attr_pno_config_params
{
3588 QCA_WLAN_VENDOR_ATTR_PNO_INVALID
= 0,
3589 /* Attributes for data used by
3590 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command.
3592 /* Unsigned 32-bit value */
3593 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM
= 1,
3594 /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_*
3595 * attributes. Array size =
3596 * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM.
3598 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY
= 2,
3600 /* Unsigned 32-bit value */
3601 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID
= 3,
3602 /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded
3603 * realm, 0 if unspecified.
3605 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM
= 4,
3606 /* An array of 16 x unsigned 32-bit value; roaming consortium ids to
3607 * match, 0 if unspecified.
3609 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID
= 5,
3610 /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if
3613 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN
= 6,
3615 /* Attributes for data used by
3616 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command.
3618 /* Unsigned 32-bit value */
3619 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS
= 7,
3621 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_*
3622 * attributes. Array size =
3623 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS.
3625 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST
= 8,
3626 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
3627 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID
= 9,
3628 /* Signed 8-bit value; threshold for considering this SSID as found,
3629 * required granularity for this threshold is 4 dBm to 8 dBm.
3631 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD
3633 /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */
3634 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS
= 11,
3635 /* Unsigned 8-bit value; auth bit field for matching WPA IE */
3636 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT
= 12,
3637 /* Unsigned 8-bit to indicate ePNO type;
3638 * It takes values from qca_wlan_epno_type
3640 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE
= 13,
3642 /* Nested attribute to send the channel list */
3643 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST
= 14,
3645 /* Unsigned 32-bit value; indicates the interval between PNO scan
3648 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL
= 15,
3649 QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI
= 16,
3650 QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI
= 17,
3651 QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX
= 18,
3652 QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS
= 19,
3653 QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS
= 20,
3654 QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS
= 21,
3655 QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS
= 22,
3656 /* Unsigned 32-bit value, representing the PNO Request ID */
3657 QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID
= 23,
3660 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST
,
3661 QCA_WLAN_VENDOR_ATTR_PNO_MAX
=
3662 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST
- 1,
3666 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why
3667 * the ACS has to be triggered. These values are used by
3668 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and
3669 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
3671 enum qca_wlan_vendor_acs_select_reason
{
3672 /* Represents the reason that the ACS triggered during the AP start */
3673 QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT
,
3674 /* Represents the reason that DFS found with the current channel */
3675 QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS
,
3676 /* Represents the reason that LTE co-exist in the current band. */
3677 QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX
,
3681 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for
3682 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd
3683 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the
3684 * external ACS policies to select the channels w.r.t. the PCL weights.
3685 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and
3686 * their PCL weights.)
3687 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to
3688 * select a channel with non-zero PCL weight.
3689 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a
3690 * channel with non-zero PCL weight.
3693 enum qca_wlan_vendor_attr_external_acs_policy
{
3694 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED
,
3695 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY
,
3699 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel.
3700 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS.
3702 enum qca_wlan_vendor_channel_prop_flags
{
3703 /* Bits 0, 1, 2, and 3 are reserved */
3706 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO
= 1 << 4,
3708 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK
= 1 << 5,
3710 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM
= 1 << 6,
3711 /* 2.4 GHz spectrum channel. */
3712 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ
= 1 << 7,
3713 /* 5 GHz spectrum channel */
3714 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ
= 1 << 8,
3715 /* Only passive scan allowed */
3716 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE
= 1 << 9,
3717 /* Dynamic CCK-OFDM channel */
3718 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN
= 1 << 10,
3719 /* GFSK channel (FHSS PHY) */
3720 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK
= 1 << 11,
3721 /* Radar found on channel */
3722 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR
= 1 << 12,
3723 /* 11a static turbo channel only */
3724 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO
= 1 << 13,
3725 /* Half rate channel */
3726 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF
= 1 << 14,
3727 /* Quarter rate channel */
3728 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER
= 1 << 15,
3730 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20
= 1 << 16,
3731 /* HT 40 with extension channel above */
3732 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS
= 1 << 17,
3733 /* HT 40 with extension channel below */
3734 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS
= 1 << 18,
3735 /* HT 40 intolerant */
3736 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL
= 1 << 19,
3737 /* VHT 20 channel */
3738 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20
= 1 << 20,
3739 /* VHT 40 with extension channel above */
3740 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS
= 1 << 21,
3741 /* VHT 40 with extension channel below */
3742 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS
= 1 << 22,
3743 /* VHT 80 channel */
3744 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80
= 1 << 23,
3745 /* HT 40 intolerant mark bit for ACS use */
3746 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK
= 1 << 24,
3747 /* Channel temporarily blocked due to noise */
3748 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED
= 1 << 25,
3749 /* VHT 160 channel */
3750 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160
= 1 << 26,
3751 /* VHT 80+80 channel */
3752 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80
= 1 << 27,
3754 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20
= 1 << 28,
3755 /* HE 40 with extension channel above */
3756 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS
= 1 << 29,
3757 /* HE 40 with extension channel below */
3758 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS
= 1 << 30,
3759 /* HE 40 intolerant */
3760 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL
= 1 << 31,
3764 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a
3765 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is
3766 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2.
3768 enum qca_wlan_vendor_channel_prop_flags_2
{
3769 /* HE 40 intolerant mark bit for ACS use */
3770 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK
= 1 << 0,
3772 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80
= 1 << 1,
3773 /* HE 160 channel */
3774 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160
= 1 << 2,
3775 /* HE 80+80 channel */
3776 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80
= 1 << 3,
3780 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for
3781 * each channel. This is used by
3782 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT.
3784 enum qca_wlan_vendor_channel_prop_flags_ext
{
3785 /* Radar found on channel */
3786 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND
= 1 << 0,
3787 /* DFS required on channel */
3788 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS
= 1 << 1,
3789 /* DFS required on channel for 2nd band of 80+80 */
3790 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2
= 1 << 2,
3791 /* If channel has been checked for DFS */
3792 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR
= 1 << 3,
3793 /* Excluded in 802.11d */
3794 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED
= 1 << 4,
3795 /* Channel Switch Announcement received on this channel */
3796 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED
= 1 << 5,
3797 /* Ad-hoc is not allowed */
3798 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC
= 1 << 6,
3799 /* Station only channel */
3800 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP
= 1 << 7,
3801 /* DFS radar history for slave device (STA mode) */
3802 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR
= 1 << 8,
3803 /* DFS CAC valid for slave device (STA mode) */
3804 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID
= 1 << 9,
3808 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel
3809 * information. These attributes are sent as part of
3810 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following
3811 * attributes correspond to a single channel.
3813 enum qca_wlan_vendor_external_acs_event_chan_info_attr
{
3814 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID
= 0,
3816 /* A bitmask (u32) with flags specified in
3817 * enum qca_wlan_vendor_channel_prop_flags.
3819 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS
= 1,
3820 /* A bitmask (u32) with flags specified in
3821 * enum qca_wlan_vendor_channel_prop_flags_ext.
3823 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT
= 2,
3824 /* frequency in MHz (u32) */
3825 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ
= 3,
3826 /* maximum regulatory transmission power (u32) */
3827 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER
= 4,
3828 /* maximum transmission power (u32) */
3829 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER
= 5,
3830 /* minimum transmission power (u32) */
3831 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER
= 6,
3832 /* regulatory class id (u8) */
3833 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID
= 7,
3834 /* maximum antenna gain in (u8) */
3835 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN
= 8,
3836 /* VHT segment 0 (u8) */
3837 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0
= 9,
3838 /* VHT segment 1 (u8) */
3839 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1
= 10,
3840 /* A bitmask (u32) with flags specified in
3841 * enum qca_wlan_vendor_channel_prop_flags_2.
3843 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2
= 11,
3846 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST
,
3847 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX
=
3848 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST
- 1,
3852 * qca_wlan_vendor_attr_pcl: Represents attributes for
3853 * preferred channel list (PCL). These attributes are sent as part of
3854 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and
3855 * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST.
3857 enum qca_wlan_vendor_attr_pcl
{
3858 QCA_WLAN_VENDOR_ATTR_PCL_INVALID
= 0,
3860 /* Channel number (u8) */
3861 QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL
= 1,
3862 /* Channel weightage (u8) */
3863 QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT
= 2,
3864 /* Channel frequency (u32) in MHz */
3865 QCA_WLAN_VENDOR_ATTR_PCL_FREQ
= 3,
3866 /* Channel flags (u32)
3867 * bit 0 set: channel to be used for GO role,
3868 * bit 1 set: channel to be used on CLI role,
3869 * bit 2 set: channel must be considered for operating channel
3870 * selection & peer chosen operating channel should be
3871 * one of the channels with this flag set,
3872 * bit 3 set: channel should be excluded in GO negotiation
3874 QCA_WLAN_VENDOR_ATTR_PCL_FLAG
= 4,
3878 * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command
3879 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by
3882 enum qca_wlan_vendor_attr_external_acs_event
{
3883 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID
= 0,
3885 /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason.
3886 * This helps ACS module to understand why ACS needs to be started.
3888 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON
= 1,
3889 /* Flag attribute to indicate if driver supports spectral scanning */
3890 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED
= 2,
3891 /* Flag attribute to indicate if 11ac is offloaded to firmware */
3892 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED
= 3,
3893 /* Flag attribute to indicate if driver provides additional channel
3894 * capability as part of scan operation
3896 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT
= 4,
3897 /* Flag attribute to indicate interface status is UP */
3898 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP
= 5,
3899 /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype
3902 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE
= 6,
3903 /* Channel width (u8). It takes one of enum nl80211_chan_width values.
3904 * This is the upper bound of channel width. ACS logic should try to get
3905 * a channel with the specified width and if not found, look for lower
3908 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH
= 7,
3909 /* This (u8) will hold values of one of enum nl80211_bands */
3910 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND
= 8,
3911 /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode
3914 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE
= 9,
3915 /* Array of (u32) supported frequency list among which ACS should choose
3918 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST
= 10,
3919 /* Preferred channel list by the driver which will have array of nested
3920 * values as per enum qca_wlan_vendor_attr_pcl attribute.
3922 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL
= 11,
3923 /* Array of nested attribute for each channel. It takes attr as defined
3924 * in enum qca_wlan_vendor_external_acs_event_chan_info_attr.
3926 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO
= 12,
3927 /* External ACS policy such as PCL mandatory, PCL preferred, etc.
3928 * It uses values defined in enum
3929 * qca_wlan_vendor_attr_external_acs_policy.
3931 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY
= 13,
3932 /* Reference RF Operating Parameter (RROP) availability information
3933 * (u16). It uses values defined in enum
3934 * qca_wlan_vendor_attr_rropavail_info.
3936 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO
= 14,
3939 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST
,
3940 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX
=
3941 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST
- 1,
3945 * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
3946 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
3947 * in priority order as decided after ACS operation in userspace.
3949 enum qca_wlan_vendor_attr_external_acs_channels
{
3950 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID
= 0,
3952 /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason
3954 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
= 1,
3956 /* Array of nested values for each channel with following attributes:
3957 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND,
3958 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
3959 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
3960 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
3961 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
3962 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
3964 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST
= 2,
3965 /* This (u8) will hold values of one of enum nl80211_bands */
3966 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND
= 3,
3967 /* Primary channel (u8) */
3968 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY
= 4,
3969 /* Secondary channel (u8) used for HT 40 MHz channels */
3970 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY
= 5,
3971 /* VHT seg0 channel (u8) */
3972 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0
= 6,
3973 /* VHT seg1 channel (u8) */
3974 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1
= 7,
3975 /* Channel width (u8). Takes one of enum nl80211_chan_width values. */
3976 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
= 8,
3979 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST
,
3980 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX
=
3981 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST
- 1
3984 enum qca_chip_power_save_failure_reason
{
3985 /* Indicates if the reason for the failure is due to a protocol
3988 QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL
= 0,
3989 /* Indicates if the reason for the failure is due to a hardware issue.
3991 QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE
= 1,
3995 * qca_attr_chip_power_save_failure: Attributes to vendor subcmd
3996 * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite
3997 * information leading to the power save failure.
3999 enum qca_attr_chip_power_save_failure
{
4000 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID
= 0,
4001 /* Reason to cause the power save failure.
4002 * These reasons are represented by
4003 * enum qca_chip_power_save_failure_reason.
4005 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON
= 1,
4008 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST
,
4009 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX
=
4010 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST
- 1,
4014 * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various
4015 * data types for which the stats have to get collected.
4017 enum qca_wlan_vendor_nud_stats_data_pkt_flags
{
4018 QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP
= 1 << 0,
4019 QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS
= 1 << 1,
4020 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE
= 1 << 2,
4021 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4
= 1 << 3,
4022 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6
= 1 << 4,
4023 /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get
4024 * to represent the stats of respective data type.
4026 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN
= 1 << 5,
4027 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK
= 1 << 6,
4028 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK
= 1 << 7,
4031 enum qca_wlan_vendor_nud_stats_set_data_pkt_info
{
4032 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID
= 0,
4033 /* Represents the data packet type to be monitored (u32).
4034 * Host driver tracks the stats corresponding to each data frame
4035 * represented by these flags.
4036 * These data packets are represented by
4037 * enum qca_wlan_vendor_nud_stats_data_pkt_flags
4039 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE
= 1,
4040 /* Name corresponding to the DNS frame for which the respective DNS
4041 * stats have to get monitored (string). Max string length 255.
4043 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME
= 2,
4044 /* source port on which the respective proto stats have to get
4047 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT
= 3,
4048 /* destination port on which the respective proto stats have to get
4051 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT
= 4,
4052 /* IPv4 address for which the destined data packets have to be
4053 * monitored. (in network byte order), u32.
4055 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4
= 5,
4056 /* IPv6 address for which the destined data packets have to be
4057 * monitored. (in network byte order), 16 bytes array.
4059 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6
= 6,
4061 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST
,
4062 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX
=
4063 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST
- 1,
4067 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd
4068 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite
4069 * information to start/stop the NUD statistics collection.
4071 enum qca_attr_nud_stats_set
{
4072 QCA_ATTR_NUD_STATS_SET_INVALID
= 0,
4074 /* Flag to start/stop the NUD statistics collection.
4075 * Start - If included, Stop - If not included
4077 QCA_ATTR_NUD_STATS_SET_START
= 1,
4078 /* IPv4 address of the default gateway (in network byte order), u32 */
4079 QCA_ATTR_NUD_STATS_GW_IPV4
= 2,
4080 /* Represents the list of data packet types to be monitored.
4081 * Host driver tracks the stats corresponding to each data frame
4082 * represented by these flags.
4083 * These data packets are represented by
4084 * enum qca_wlan_vendor_nud_stats_set_data_pkt_info
4086 QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO
= 3,
4089 QCA_ATTR_NUD_STATS_SET_LAST
,
4090 QCA_ATTR_NUD_STATS_SET_MAX
=
4091 QCA_ATTR_NUD_STATS_SET_LAST
- 1,
4094 enum qca_attr_nud_data_stats
{
4095 QCA_ATTR_NUD_DATA_STATS_INVALID
= 0,
4096 /* Data packet type for which the stats are collected (u32).
4097 * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags
4099 QCA_ATTR_NUD_STATS_PKT_TYPE
= 1,
4100 /* Name corresponding to the DNS frame for which the respective DNS
4101 * stats are monitored (string). Max string length 255.
4103 QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME
= 2,
4104 /* source port on which the respective proto stats are collected (u32).
4106 QCA_ATTR_NUD_STATS_PKT_SRC_PORT
= 3,
4107 /* destination port on which the respective proto stats are collected
4110 QCA_ATTR_NUD_STATS_PKT_DEST_PORT
= 4,
4111 /* IPv4 address for which the destined data packets have to be
4112 * monitored. (in network byte order), u32.
4114 QCA_ATTR_NUD_STATS_PKT_DEST_IPV4
= 5,
4115 /* IPv6 address for which the destined data packets have to be
4116 * monitored. (in network byte order), 16 bytes array.
4118 QCA_ATTR_NUD_STATS_PKT_DEST_IPV6
= 6,
4119 /* Data packet Request count received from netdev (u32). */
4120 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV
= 7,
4121 /* Data packet Request count sent to lower MAC from upper MAC (u32). */
4122 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC
= 8,
4123 /* Data packet Request count received by lower MAC from upper MAC
4126 QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC
= 9,
4127 /* Data packet Request count successfully transmitted by the device
4130 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS
= 10,
4131 /* Data packet Response count received by lower MAC (u32) */
4132 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC
= 11,
4133 /* Data packet Response count received by upper MAC (u32) */
4134 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC
= 12,
4135 /* Data packet Response count delivered to netdev (u32) */
4136 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV
= 13,
4137 /* Data Packet Response count that are dropped out of order (u32) */
4138 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP
= 14,
4141 QCA_ATTR_NUD_DATA_STATS_LAST
,
4142 QCA_ATTR_NUD_DATA_STATS_MAX
=
4143 QCA_ATTR_NUD_DATA_STATS_LAST
- 1,
4147 * qca_attr_nud_stats_get: Attributes to vendor subcmd
4148 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite
4149 * NUD statistics collected when queried.
4151 enum qca_attr_nud_stats_get
{
4152 QCA_ATTR_NUD_STATS_GET_INVALID
= 0,
4153 /* ARP Request count from netdev (u32) */
4154 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV
= 1,
4155 /* ARP Request count sent to lower MAC from upper MAC (u32) */
4156 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC
= 2,
4157 /* ARP Request count received by lower MAC from upper MAC (u32) */
4158 QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC
= 3,
4159 /* ARP Request count successfully transmitted by the device (u32) */
4160 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS
= 4,
4161 /* ARP Response count received by lower MAC (u32) */
4162 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC
= 5,
4163 /* ARP Response count received by upper MAC (u32) */
4164 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC
= 6,
4165 /* ARP Response count delivered to netdev (u32) */
4166 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV
= 7,
4167 /* ARP Response count dropped due to out of order reception (u32) */
4168 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP
= 8,
4169 /* Flag indicating if the station's link to the AP is active.
4170 * Active Link - If included, Inactive link - If not included
4172 QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE
= 9,
4173 /* Flag indicating if there is any duplicate address detected (DAD).
4174 * Yes - If detected, No - If not detected.
4176 QCA_ATTR_NUD_STATS_IS_DAD
= 10,
4177 /* List of Data packet types for which the stats are requested.
4178 * This list does not carry ARP stats as they are done by the
4179 * above attributes. Represented by enum qca_attr_nud_data_stats.
4181 QCA_ATTR_NUD_STATS_DATA_PKT_STATS
= 11,
4184 QCA_ATTR_NUD_STATS_GET_LAST
,
4185 QCA_ATTR_NUD_STATS_GET_MAX
=
4186 QCA_ATTR_NUD_STATS_GET_LAST
- 1,
4189 enum qca_wlan_btm_candidate_status
{
4190 QCA_STATUS_ACCEPT
= 0,
4191 QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED
= 1,
4192 QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED
= 2,
4193 QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY
= 3,
4194 QCA_STATUS_REJECT_LOW_RSSI
= 4,
4195 QCA_STATUS_REJECT_HIGH_INTERFERENCE
= 5,
4196 QCA_STATUS_REJECT_UNKNOWN
= 6,
4199 enum qca_wlan_vendor_attr_btm_candidate_info
{
4200 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID
= 0,
4202 /* 6-byte MAC address representing the BSSID of transition candidate */
4203 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID
= 1,
4204 /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status
4205 * returned by the driver. It says whether the BSSID provided in
4206 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by
4207 * the driver, if not it specifies the reason for rejection.
4208 * Note that the user-space can overwrite the transition reject reason
4209 * codes provided by driver based on more information.
4211 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS
= 2,
4214 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST
,
4215 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX
=
4216 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST
- 1,
4219 enum qca_attr_trace_level
{
4220 QCA_ATTR_TRACE_LEVEL_INVALID
= 0,
4222 * Nested array of the following attributes:
4223 * QCA_ATTR_TRACE_LEVEL_MODULE,
4224 * QCA_ATTR_TRACE_LEVEL_MASK.
4226 QCA_ATTR_TRACE_LEVEL_PARAM
= 1,
4228 * Specific QCA host driver module. Please refer to the QCA host
4229 * driver implementation to get the specific module ID.
4231 QCA_ATTR_TRACE_LEVEL_MODULE
= 2,
4232 /* Different trace level masks represented in the QCA host driver. */
4233 QCA_ATTR_TRACE_LEVEL_MASK
= 3,
4236 QCA_ATTR_TRACE_LEVEL_AFTER_LAST
,
4237 QCA_ATTR_TRACE_LEVEL_MAX
=
4238 QCA_ATTR_TRACE_LEVEL_AFTER_LAST
- 1,
4242 * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities
4244 enum qca_wlan_vendor_attr_get_he_capabilities
{
4245 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID
= 0,
4246 /* Whether HE capabilities is supported
4247 * (u8 attribute: 0 = not supported, 1 = supported)
4249 QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED
= 1,
4250 /* HE PHY capabilities, array of 3 u32 values */
4251 QCA_WLAN_VENDOR_ATTR_PHY_CAPAB
= 2,
4252 /* HE MAC capabilities (u32 attribute) */
4253 QCA_WLAN_VENDOR_ATTR_MAC_CAPAB
= 3,
4254 /* HE MCS map (u32 attribute) */
4255 QCA_WLAN_VENDOR_ATTR_HE_MCS
= 4,
4256 /* Number of SS (u32 attribute) */
4257 QCA_WLAN_VENDOR_ATTR_NUM_SS
= 5,
4258 /* RU count (u32 attribute) */
4259 QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK
= 6,
4260 /* PPE threshold data, array of 8 u32 values */
4261 QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD
= 7,
4264 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST
,
4265 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX
=
4266 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST
- 1,
4270 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters
4272 enum qca_wlan_vendor_attr_spectral_scan
{
4273 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID
= 0,
4274 /* Number of times the chip enters spectral scan mode before
4275 * deactivating spectral scans. When set to 0, chip will enter spectral
4276 * scan mode continuously. u32 attribute.
4278 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT
= 1,
4279 /* Spectral scan period. Period increment resolution is 256*Tclk,
4280 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute.
4282 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD
= 2,
4283 /* Spectral scan priority. u32 attribute. */
4284 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY
= 3,
4285 /* Number of FFT data points to compute. u32 attribute. */
4286 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE
= 4,
4287 /* Enable targeted gain change before starting the spectral scan FFT.
4290 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA
= 5,
4291 /* Restart a queued spectral scan. u32 attribute. */
4292 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA
= 6,
4293 /* Noise floor reference number for the calculation of bin power.
4296 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF
= 7,
4297 /* Disallow spectral scan triggers after TX/RX packets by setting
4298 * this delay value to roughly SIFS time period or greater.
4301 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY
= 8,
4302 /* Number of strong bins (inclusive) per sub-channel, below
4303 * which a signal is declared a narrow band tone. u32 attribute.
4305 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR
= 9,
4306 /* Specify the threshold over which a bin is declared strong (for
4307 * scan bandwidth analysis). u32 attribute.
4309 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR
= 10,
4310 /* Spectral scan report mode. u32 attribute. */
4311 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE
= 11,
4312 /* RSSI report mode, if the ADC RSSI is below
4313 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR,
4314 * then FFTs will not trigger, but timestamps and summaries get
4315 * reported. u32 attribute.
4317 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE
= 12,
4318 /* ADC RSSI must be greater than or equal to this threshold (signed dB)
4319 * to ensure spectral scan reporting with normal error code.
4322 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR
= 13,
4323 /* Format of frequency bin magnitude for spectral scan triggered FFTs:
4324 * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)).
4327 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT
= 14,
4328 /* Format of FFT report to software for spectral scan triggered FFTs.
4329 * 0: No FFT report (only spectral scan summary report)
4330 * 1: 2-dword summary of metrics for each completed FFT + spectral scan
4332 * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled
4333 * bins (in-band) per FFT + spectral scan summary report
4334 * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled
4335 * bins (all) per FFT + spectral scan summary report
4338 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE
= 15,
4339 /* Number of LSBs to shift out in order to scale the FFT bins.
4342 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE
= 16,
4343 /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes
4344 * in dBm power. u32 attribute.
4346 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ
= 17,
4347 /* Per chain enable mask to select input ADC for search FFT.
4350 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK
= 18,
4351 /* An unsigned 64-bit integer provided by host driver to identify the
4352 * spectral scan request. This attribute is included in the scan
4353 * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
4354 * and used as an attribute in
4355 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the
4356 * specific scan to be stopped.
4358 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE
= 19,
4359 /* Skip interval for FFT reports. u32 attribute */
4360 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD
= 20,
4361 /* Set to report only one set of FFT results.
4364 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT
= 21,
4365 /* Debug level for spectral module in driver.
4366 * 0 : Verbosity level 0
4367 * 1 : Verbosity level 1
4368 * 2 : Verbosity level 2
4369 * 3 : Matched filterID display
4370 * 4 : One time dump of FFT report
4373 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL
= 22,
4374 /* Type of spectral scan request. u32 attribute.
4375 * It uses values defined in enum
4376 * qca_wlan_vendor_attr_spectral_scan_request_type.
4378 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE
= 23,
4380 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST
,
4381 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX
=
4382 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST
- 1,
4386 * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command
4387 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS.
4389 enum qca_wlan_vendor_attr_spectral_diag_stats
{
4390 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID
= 0,
4391 /* Number of spectral TLV signature mismatches.
4394 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH
= 1,
4395 /* Number of spectral phyerror events with insufficient length when
4396 * parsing for secondary 80 search FFT report. u64 attribute.
4398 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN
= 2,
4399 /* Number of spectral phyerror events without secondary 80
4400 * search FFT report. u64 attribute.
4402 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT
= 3,
4403 /* Number of spectral phyerror events with vht operation segment 1 id
4404 * mismatches in search fft report. u64 attribute.
4406 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH
= 4,
4407 /* Number of spectral phyerror events with vht operation segment 2 id
4408 * mismatches in search fft report. u64 attribute.
4410 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH
= 5,
4412 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST
,
4413 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX
=
4414 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST
- 1,
4418 * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command
4419 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO.
4421 enum qca_wlan_vendor_attr_spectral_cap
{
4422 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID
= 0,
4423 /* Flag attribute to indicate phydiag capability */
4424 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG
= 1,
4425 /* Flag attribute to indicate radar detection capability */
4426 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR
= 2,
4427 /* Flag attribute to indicate spectral capability */
4428 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL
= 3,
4429 /* Flag attribute to indicate advanced spectral capability */
4430 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL
= 4,
4431 /* Spectral hardware generation. u32 attribute.
4432 * It uses values defined in enum
4433 * qca_wlan_vendor_spectral_scan_cap_hw_gen.
4435 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN
= 5,
4436 /* Spectral bin scaling formula ID. u16 attribute.
4437 * It uses values defined in enum
4438 * qca_wlan_vendor_spectral_scan_cap_formula_id.
4440 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID
= 6,
4441 /* Spectral bin scaling param - low level offset.
4444 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET
= 7,
4445 /* Spectral bin scaling param - high level offset.
4448 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET
= 8,
4449 /* Spectral bin scaling param - RSSI threshold.
4452 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR
= 9,
4453 /* Spectral bin scaling param - default AGC max gain.
4456 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN
= 10,
4458 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST
,
4459 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX
=
4460 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST
- 1,
4464 * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command
4465 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS.
4467 enum qca_wlan_vendor_attr_spectral_scan_status
{
4468 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID
= 0,
4469 /* Flag attribute to indicate whether spectral scan is enabled */
4470 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED
= 1,
4471 /* Flag attribute to indicate whether spectral scan is in progress*/
4472 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE
= 2,
4474 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST
,
4475 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX
=
4476 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST
- 1,
4480 * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for
4481 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd
4482 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the
4483 * spectral scan request types.
4484 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to
4485 * set the spectral parameters and start scan.
4486 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to
4487 * only set the spectral parameters.
4488 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to
4489 * only start the spectral scan.
4491 enum qca_wlan_vendor_attr_spectral_scan_request_type
{
4492 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG
,
4493 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN
,
4494 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG
,
4498 * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for
4499 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd
4500 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the
4501 * spectral hardware generation.
4502 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1
4503 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2
4504 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3
4506 enum qca_wlan_vendor_spectral_scan_cap_hw_gen
{
4507 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1
= 0,
4508 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2
= 1,
4509 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3
= 2,
4512 enum qca_wlan_vendor_tos
{
4513 QCA_WLAN_VENDOR_TOS_BK
= 0,
4514 QCA_WLAN_VENDOR_TOS_BE
= 1,
4515 QCA_WLAN_VENDOR_TOS_VI
= 2,
4516 QCA_WLAN_VENDOR_TOS_VO
= 3,
4520 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command
4521 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS.
4523 enum qca_wlan_vendor_attr_active_tos
{
4524 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID
= 0,
4525 /* Type Of Service - Represented by qca_wlan_vendor_tos */
4526 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS
= 1,
4527 /* Flag attribute representing the start (attribute included) or stop
4528 * (attribute not included) of the respective TOS.
4530 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START
= 2,
4533 enum qca_wlan_vendor_hang_reason
{
4534 /* Unspecified reason */
4535 QCA_WLAN_HANG_REASON_UNSPECIFIED
= 0,
4536 /* No Map for the MAC entry for the received frame */
4537 QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND
= 1,
4538 /* Peer deletion timeout happened */
4539 QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT
= 2,
4540 /* Peer unmap timeout */
4541 QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT
= 3,
4542 /* Scan request timed out */
4543 QCA_WLAN_HANG_SCAN_REQ_EXPIRED
= 4,
4544 /* Consecutive Scan attempt failures */
4545 QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES
= 5,
4546 /* Unable to get the message buffer */
4547 QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE
= 6,
4548 /* Current command processing is timedout */
4549 QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT
= 7,
4550 /* Timeout for an ACK from FW for suspend request */
4551 QCA_WLAN_HANG_SUSPEND_TIMEOUT
= 8,
4552 /* Timeout for an ACK from FW for resume request */
4553 QCA_WLAN_HANG_RESUME_TIMEOUT
= 9,
4554 /* Transmission timeout for consecutive data frames */
4555 QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT
= 10,
4556 /* Timeout for the TX completion status of data frame */
4557 QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT
= 11,
4558 /* DXE failure for TX/RX, DXE resource unavailability */
4559 QCA_WLAN_HANG_DXE_FAILURE
= 12,
4560 /* WMI pending commands exceed the maximum count */
4561 QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS
= 13,
4565 * enum qca_wlan_vendor_attr_hang - Used by the vendor command
4566 * QCA_NL80211_VENDOR_SUBCMD_HANG.
4568 enum qca_wlan_vendor_attr_hang
{
4569 QCA_WLAN_VENDOR_ATTR_HANG_INVALID
= 0,
4570 /* Reason for the hang - u32 attribute with a value from enum
4571 * qca_wlan_vendor_hang_reason.
4573 QCA_WLAN_VENDOR_ATTR_HANG_REASON
= 1,
4575 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST
,
4576 QCA_WLAN_VENDOR_ATTR_HANG_MAX
=
4577 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST
- 1,
4581 * enum qca_wlan_vendor_attr_flush_pending - Attributes for
4582 * flushing pending traffic in firmware.
4584 * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address.
4585 * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending
4586 * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK,
4587 * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to
4588 * flush packets with access category.
4590 enum qca_wlan_vendor_attr_flush_pending
{
4591 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID
= 0,
4592 QCA_WLAN_VENDOR_ATTR_PEER_ADDR
= 1,
4593 QCA_WLAN_VENDOR_ATTR_AC
= 2,
4596 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST
,
4597 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX
=
4598 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST
- 1,
4602 * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for
4603 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd
4604 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the
4605 * Spectral bin scaling formula ID.
4606 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling
4607 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain
4608 * and RSSI threshold based formula.
4610 enum qca_wlan_vendor_spectral_scan_cap_formula_id
{
4611 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING
= 0,
4612 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED
= 1,
4616 * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative
4617 * RF Operating Parameter (RROP) information is available, and if so, at which
4618 * point in the application-driver interaction sequence it can be retrieved by
4619 * the application from the driver. This point may vary by architecture and
4620 * other factors. This is a u16 value.
4622 enum qca_wlan_vendor_attr_rropavail_info
{
4623 /* RROP information is unavailable. */
4624 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE
,
4625 /* RROP information is available and the application can retrieve the
4626 * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
4627 * event from the driver.
4629 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START
,
4630 /* RROP information is available only after a vendor specific scan
4631 * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has
4632 * successfully completed. The application can retrieve the information
4633 * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from
4636 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END
,
4640 * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific
4641 * Representative RF Operating Parameter (RROP) information. It is sent for the
4642 * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is
4643 * intended for use by external Auto Channel Selection applications. It provides
4644 * guidance values for some RF parameters that are used by the system during
4645 * operation. These values could vary by channel, band, radio, and so on.
4647 enum qca_wlan_vendor_attr_rrop_info
{
4648 QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID
= 0,
4650 /* Representative Tx Power List (RTPL) which has an array of nested
4651 * values as per attributes in enum qca_wlan_vendor_attr_rtplinst.
4653 QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL
= 1,
4655 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST
,
4656 QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX
=
4657 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST
- 1
4661 * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list
4662 * entry instances in the Representative Tx Power List (RTPL). It provides
4663 * simplified power values intended for helping external Auto channel Selection
4664 * applications compare potential Tx power performance between channels, other
4665 * operating conditions remaining identical. These values are not necessarily
4666 * the actual Tx power values that will be used by the system. They are also not
4667 * necessarily the max or average values that will be used. Instead, they are
4668 * relative, summarized keys for algorithmic use computed by the driver or
4669 * underlying firmware considering a number of vendor specific factors.
4671 enum qca_wlan_vendor_attr_rtplinst
{
4672 QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID
= 0,
4674 /* Primary channel number (u8) */
4675 QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY
= 1,
4676 /* Representative Tx power in dBm (s32) with emphasis on throughput. */
4677 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT
= 2,
4678 /* Representative Tx power in dBm (s32) with emphasis on range. */
4679 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE
= 3,
4681 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST
,
4682 QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX
=
4683 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST
- 1,
4687 * enum qca_wlan_vendor_attr_config_latency_level - Level for
4688 * wlan latency module.
4690 * There will be various of Wi-Fi functionality like scan/roaming/adaptive
4691 * power saving which would causing data exchange out of service, this
4692 * would be a big impact on latency. For latency sensitive applications over
4693 * Wi-Fi are intolerant to such operations and thus would configure them
4694 * to meet their respective needs. It is well understood by such applications
4695 * that altering the default behavior would degrade the Wi-Fi functionality
4696 * w.r.t the above pointed WLAN operations.
4698 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL:
4699 * Default WLAN operation level which throughput orientated.
4700 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE:
4701 * Use moderate level to improve latency by limit scan duration.
4702 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW:
4703 * Use low latency level to benifit application like concurrent
4704 * downloading or video streaming via constraint scan/adaptive PS.
4705 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW:
4706 * Use ultra low latency level to benefit for gaming/voice
4707 * application via constraint scan/roaming/adaptive PS.
4709 enum qca_wlan_vendor_attr_config_latency_level
{
4710 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID
= 0,
4711 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL
= 1,
4712 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE
= 2,
4713 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW
= 3,
4714 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW
= 4,
4717 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST
,
4718 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX
=
4719 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST
- 1,
4723 * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command
4724 * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
4726 enum qca_wlan_vendor_attr_mac
{
4727 QCA_WLAN_VENDOR_ATTR_MAC_INVALID
= 0,
4729 /* MAC mode info list which has an array of nested values as
4730 * per attributes in enum qca_wlan_vendor_attr_mac_mode_info.
4732 QCA_WLAN_VENDOR_ATTR_MAC_INFO
= 1,
4735 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST
,
4736 QCA_WLAN_VENDOR_ATTR_MAC_MAX
=
4737 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST
- 1,
4741 * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected
4742 * Wi-Fi netdev interface on a respective MAC.
4743 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO.
4745 enum qca_wlan_vendor_attr_mac_iface_info
{
4746 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID
= 0,
4747 /* Wi-Fi netdev's interface index (u32) */
4748 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX
= 1,
4749 /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */
4750 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ
= 2,
4753 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST
,
4754 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX
=
4755 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST
- 1,
4759 * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information.
4760 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the
4761 * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
4763 enum qca_wlan_vendor_attr_mac_info
{
4764 QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID
= 0,
4765 /* Hardware MAC ID associated for the MAC (u32) */
4766 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID
= 1,
4767 /* Band supported by the MAC at a given point.
4768 * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum
4771 QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND
= 2,
4772 /* Refers to list of WLAN netdev interfaces associated with this MAC.
4773 * Represented by enum qca_wlan_vendor_attr_mac_iface_info.
4775 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO
= 3,
4778 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST
,
4779 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX
=
4780 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST
- 1,
4784 * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command
4785 * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET.
4787 enum qca_wlan_vendor_attr_get_logger_features
{
4788 QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID
= 0,
4789 /* Unsigned 32-bit enum value of wifi_logger_supported_features */
4790 QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED
= 1,
4792 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST
,
4793 QCA_WLAN_VENDOR_ATTR_LOGGER_MAX
=
4794 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST
- 1,
4798 * enum wifi_logger_supported_features - Values for supported logger features
4800 enum wifi_logger_supported_features
{
4801 WIFI_LOGGER_MEMORY_DUMP_FEATURE
= (1 << (0)),
4802 WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE
= (1 << (1)),
4803 WIFI_LOGGER_CONNECT_EVENT_FEATURE
= (1 << (2)),
4804 WIFI_LOGGER_POWER_EVENT_FEATURE
= (1 << (3)),
4805 WIFI_LOGGER_WAKE_LOCK_FEATURE
= (1 << (4)),
4806 WIFI_LOGGER_VERBOSE_FEATURE
= (1 << (5)),
4807 WIFI_LOGGER_WATCHDOG_TIMER_FEATURE
= (1 << (6)),
4808 WIFI_LOGGER_DRIVER_DUMP_FEATURE
= (1 << (7)),
4809 WIFI_LOGGER_PACKET_FATE_FEATURE
= (1 << (8)),
4813 * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get
4814 * capabilities features
4816 enum qca_wlan_tdls_caps_features_supported
{
4817 WIFI_TDLS_SUPPORT
= (1 << (0)),
4818 WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT
= (1 << (1)),
4819 WIFI_TDLS_OFFCHANNEL_SUPPORT
= (1 << (2))
4823 * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command
4824 * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES.
4826 enum qca_wlan_vendor_attr_tdls_get_capabilities
{
4827 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID
= 0,
4828 /* Indicates the max concurrent sessions */
4829 /* Unsigned 32-bit value */
4830 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS
,
4831 /* Indicates the support for features */
4832 /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported
4834 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED
,
4837 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST
,
4838 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX
=
4839 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST
- 1,
4843 * enum qca_wlan_offloaded_packets_sending_control - Offload packets control
4844 * command used as value for the attribute
4845 * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL.
4847 enum qca_wlan_offloaded_packets_sending_control
{
4848 QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID
= 0,
4849 QCA_WLAN_OFFLOADED_PACKETS_SENDING_START
,
4850 QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP
4854 * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command
4855 * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS.
4857 enum qca_wlan_vendor_attr_offloaded_packets
{
4858 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID
= 0,
4859 /* Takes valid value from the enum
4860 * qca_wlan_offloaded_packets_sending_control
4861 * Unsigned 32-bit value
4863 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL
,
4864 /* Unsigned 32-bit value */
4865 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID
,
4866 /* array of u8 len: Max packet size */
4867 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA
,
4868 /* 6-byte MAC address used to represent source MAC address */
4869 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR
,
4870 /* 6-byte MAC address used to represent destination MAC address */
4871 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR
,
4872 /* Unsigned 32-bit value, in milli seconds */
4873 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD
,
4876 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST
,
4877 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX
=
4878 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST
- 1,
4882 * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values
4883 * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL.
4885 enum qca_wlan_rssi_monitoring_control
{
4886 QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID
= 0,
4887 QCA_WLAN_RSSI_MONITORING_START
,
4888 QCA_WLAN_RSSI_MONITORING_STOP
,
4892 * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command
4893 * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI.
4895 enum qca_wlan_vendor_attr_rssi_monitoring
{
4896 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID
= 0,
4897 /* Takes valid value from the enum
4898 * qca_wlan_rssi_monitoring_control
4899 * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control
4901 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL
,
4902 /* Unsigned 32-bit value */
4903 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID
,
4904 /* Signed 8-bit value in dBm */
4905 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI
,
4906 /* Signed 8-bit value in dBm */
4907 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI
,
4908 /* attributes to be used/received in callback */
4909 /* 6-byte MAC address used to represent current BSSID MAC address */
4910 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID
,
4911 /* Signed 8-bit value indicating the current RSSI */
4912 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI
,
4914 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST
,
4915 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX
=
4916 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST
- 1,
4920 * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command
4921 * QCA_NL80211_VENDOR_SUBCMD_NDP.
4923 enum qca_wlan_vendor_attr_ndp_params
{
4924 QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID
= 0,
4925 /* Unsigned 32-bit value
4926 * enum of sub commands values in qca_wlan_ndp_sub_cmd
4928 QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD
,
4929 /* Unsigned 16-bit value */
4930 QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID
,
4931 /* NL attributes for data used NDP SUB cmds */
4932 /* Unsigned 32-bit value indicating a service info */
4933 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID
,
4934 /* Unsigned 32-bit value; channel frequency in MHz */
4935 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL
,
4936 /* Interface Discovery MAC address. An array of 6 Unsigned int8 */
4937 QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR
,
4938 /* Interface name on which NDP is being created */
4939 QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR
,
4940 /* Unsigned 32-bit value for security */
4941 /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */
4942 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY
,
4943 /* Unsigned 32-bit value for QoS */
4944 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS
,
4945 /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */
4946 QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO
,
4947 /* Unsigned 32-bit value for NDP instance Id */
4948 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID
,
4949 /* Array of instance Ids */
4950 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY
,
4951 /* Unsigned 32-bit value for initiator/responder NDP response code
4954 QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE
,
4955 /* NDI MAC address. An array of 6 Unsigned int8 */
4956 QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR
,
4957 /* Unsigned 32-bit value errors types returned by driver
4958 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
4959 * NanStatusType includes these values.
4961 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE
,
4962 /* Unsigned 32-bit value error values returned by driver
4963 * The nan_i.h in AOSP project platform/hardware/qcom/wlan
4964 * NanInternalStatusType includes these values.
4966 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE
,
4967 /* Unsigned 32-bit value for Channel setup configuration
4968 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
4969 * NanDataPathChannelCfg includes these values.
4971 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG
,
4972 /* Unsigned 32-bit value for Cipher Suite Shared Key Type */
4973 QCA_WLAN_VENDOR_ATTR_NDP_CSID
,
4974 /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */
4975 QCA_WLAN_VENDOR_ATTR_NDP_PMK
,
4976 /* Security Context Identifier that contains the PMKID
4977 * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes
4979 QCA_WLAN_VENDOR_ATTR_NDP_SCID
,
4980 /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */
4981 QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE
,
4982 /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */
4983 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME
,
4984 /* Unsigned 32-bit bitmap indicating schedule update
4986 * BIT_1: Channel list update
4988 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON
,
4989 /* Unsigned 32-bit value for NSS */
4990 QCA_WLAN_VENDOR_ATTR_NDP_NSS
,
4991 /* Unsigned 32-bit value for NUMBER NDP CHANNEL */
4992 QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS
,
4993 /* Unsigned 32-bit value for CHANNEL BANDWIDTH
4994 * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz
4996 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH
,
4997 /* Array of channel/band width */
4998 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO
,
4999 /* IPv6 address used by NDP (in network byte order), 16 bytes array.
5000 * This attribute is used and optional for ndp request, ndp response,
5001 * ndp indication, and ndp confirm.
5003 QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR
= 27,
5004 /* Unsigned 16-bit value indicating transport port used by NDP.
5005 * This attribute is used and optional for ndp response, ndp indication,
5008 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT
= 28,
5009 /* Unsigned 8-bit value indicating protocol used by NDP and assigned by
5010 * the Internet Assigned Numbers Authority (IANA) as per:
5011 * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
5012 * This attribute is used and optional for ndp response, ndp indication,
5015 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL
= 29,
5016 /* Unsigned 8-bit value indicating if NDP remote peer supports NAN NDPE.
5017 * 1:support 0:not support
5019 QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT
= 30,
5022 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST
,
5023 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX
=
5024 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST
- 1,
5027 enum qca_wlan_ndp_sub_cmd
{
5028 QCA_WLAN_VENDOR_ATTR_NDP_INVALID
= 0,
5029 /* Command to create a NAN data path interface */
5030 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE
= 1,
5031 /* Command to delete a NAN data path interface */
5032 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE
= 2,
5033 /* Command to initiate a NAN data path session */
5034 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST
= 3,
5035 /* Command to notify if the NAN data path session was sent */
5036 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE
= 4,
5037 /* Command to respond to NAN data path session */
5038 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST
= 5,
5039 /* Command to notify on the responder about the response */
5040 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE
= 6,
5041 /* Command to initiate a NAN data path end */
5042 QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST
= 7,
5043 /* Command to notify the if end request was sent */
5044 QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE
= 8,
5045 /* Command to notify the peer about the end request */
5046 QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND
= 9,
5047 /* Command to confirm the NAN data path session is complete */
5048 QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND
= 10,
5049 /* Command to indicate the peer about the end request being received */
5050 QCA_WLAN_VENDOR_ATTR_NDP_END_IND
= 11,
5051 /* Command to indicate the peer of schedule update */
5052 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND
= 12
5056 * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command
5057 * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD.
5059 enum qca_wlan_vendor_attr_nd_offload
{
5060 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID
= 0,
5061 /* Flag to set Neighbour Discovery offload */
5062 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG
,
5064 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST
,
5065 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX
=
5066 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST
- 1,
5070 * enum packet_filter_sub_cmd - Packet filter sub commands
5072 enum packet_filter_sub_cmd
{
5074 * Write packet filter program and/or data. The driver/firmware should
5075 * disable APF before writing into local buffer and re-enable APF after
5078 QCA_WLAN_SET_PACKET_FILTER
= 1,
5079 /* Get packet filter feature capabilities from driver */
5080 QCA_WLAN_GET_PACKET_FILTER
= 2,
5082 * Write packet filter program and/or data. User space will send the
5083 * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command
5084 * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key
5085 * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over
5086 * enable/disable is given to user space with this command. Also,
5087 * user space sends the length of program portion in the buffer within
5088 * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH.
5090 QCA_WLAN_WRITE_PACKET_FILTER
= 3,
5091 /* Read packet filter program and/or data */
5092 QCA_WLAN_READ_PACKET_FILTER
= 4,
5093 /* Enable APF feature */
5094 QCA_WLAN_ENABLE_PACKET_FILTER
= 5,
5095 /* Disable APF feature */
5096 QCA_WLAN_DISABLE_PACKET_FILTER
= 6,
5100 * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by
5101 * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER.
5103 enum qca_wlan_vendor_attr_packet_filter
{
5104 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID
= 0,
5105 /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */
5106 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD
,
5107 /* Unsigned 32-bit value indicating the packet filter version */
5108 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION
,
5109 /* Unsigned 32-bit value indicating the packet filter id */
5110 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID
,
5112 * Unsigned 32-bit value indicating the packet filter size including
5115 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE
,
5116 /* Unsigned 32-bit value indicating the packet filter current offset */
5117 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET
,
5118 /* Program and/or data in bytes */
5119 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM
,
5120 /* Unsigned 32-bit value of the length of the program section in packet
5123 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH
= 7,
5126 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST
,
5127 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX
=
5128 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST
- 1,
5132 * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command
5133 * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE.
5135 enum qca_wlan_vendor_drv_info
{
5136 QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID
= 0,
5137 /* Maximum Message size info between firmware & HOST
5138 * Unsigned 32-bit value
5140 QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE
,
5142 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST
,
5143 QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX
=
5144 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST
- 1,
5148 * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor
5149 * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS.
5151 enum qca_wlan_vendor_attr_wake_stats
{
5152 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID
= 0,
5153 /* Unsigned 32-bit value indicating the total count of wake event */
5154 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE
,
5155 /* Array of individual wake count, each index representing wake reason
5157 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR
,
5158 /* Unsigned 32-bit value representing wake count array */
5159 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ
,
5160 /* Unsigned 32-bit total wake count value of driver/fw */
5161 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE
,
5162 /* Array of wake stats of driver/fw */
5163 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR
,
5164 /* Unsigned 32-bit total wake count value of driver/fw */
5165 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ
,
5166 /* Unsigned 32-bit total wake count value of packets received */
5167 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE
,
5168 /* Unsigned 32-bit wake count value unicast packets received */
5169 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT
,
5170 /* Unsigned 32-bit wake count value multicast packets received */
5171 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT
,
5172 /* Unsigned 32-bit wake count value broadcast packets received */
5173 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT
,
5174 /* Unsigned 32-bit wake count value of ICMP packets */
5175 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT
,
5176 /* Unsigned 32-bit wake count value of ICMP6 packets */
5177 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT
,
5178 /* Unsigned 32-bit value ICMP6 router advertisement */
5179 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA
,
5180 /* Unsigned 32-bit value ICMP6 neighbor advertisement */
5181 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA
,
5182 /* Unsigned 32-bit value ICMP6 neighbor solicitation */
5183 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS
,
5184 /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */
5185 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT
,
5186 /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */
5187 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT
,
5188 /* Unsigned 32-bit wake count value of receive side multicast */
5189 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT
,
5190 /* Unsigned 32-bit wake count value of a given RSSI breach */
5191 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT
,
5192 /* Unsigned 32-bit wake count value of low RSSI */
5193 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT
,
5194 /* Unsigned 32-bit value GSCAN count */
5195 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT
,
5196 /* Unsigned 32-bit value PNO complete count */
5197 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT
,
5198 /* Unsigned 32-bit value PNO match count */
5199 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT
,
5201 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST
,
5202 QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX
=
5203 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST
- 1,
5207 * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set
5208 * cmd value. Used for NL attributes for data used by
5209 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
5211 enum qca_wlan_vendor_attr_thermal_cmd
{
5212 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID
= 0,
5213 /* The value of command, driver will implement different operations
5214 * according to this value. It uses values defined in
5215 * enum qca_wlan_vendor_attr_thermal_cmd_type.
5218 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE
= 1,
5221 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST
,
5222 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX
=
5223 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST
- 1
5227 * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for
5228 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd
5229 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the
5230 * thermal command types sent to driver.
5231 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to
5232 * get thermal shutdown configuration parameters for display. Parameters
5233 * responded from driver are defined in
5234 * enum qca_wlan_vendor_attr_get_thermal_params_rsp.
5235 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to
5236 * get temperature. Host should respond with a temperature data. It is defined
5237 * in enum qca_wlan_vendor_attr_thermal_get_temperature.
5238 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal
5240 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal
5243 enum qca_wlan_vendor_attr_thermal_cmd_type
{
5244 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS
,
5245 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE
,
5246 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND
,
5247 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME
,
5251 * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes
5252 * to get chip temperature by user.
5253 * enum values are used for NL attributes for data used by
5254 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used
5255 * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
5257 enum qca_wlan_vendor_attr_thermal_get_temperature
{
5258 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID
= 0,
5259 /* Temperature value (degree Celsius) from driver.
5262 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA
,
5265 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST
,
5266 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX
=
5267 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST
- 1,
5271 * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes
5272 * to get configuration parameters of thermal shutdown feature. Enum values are
5273 * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data
5274 * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
5276 enum qca_wlan_vendor_attr_get_thermal_params_rsp
{
5277 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID
= 0,
5278 /* Indicate if the thermal shutdown feature is enabled.
5279 * NLA_FLAG attribute.
5281 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN
,
5282 /* Indicate if the auto mode is enabled.
5283 * Enable: Driver triggers the suspend/resume action.
5284 * Disable: User space triggers the suspend/resume action.
5285 * NLA_FLAG attribute.
5287 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN
,
5288 /* Thermal resume threshold (degree Celsius). Issue the resume command
5289 * if the temperature value is lower than this threshold.
5292 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH
,
5293 /* Thermal warning threshold (degree Celsius). FW reports temperature
5294 * to driver if it's higher than this threshold.
5297 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH
,
5298 /* Thermal suspend threshold (degree Celsius). Issue the suspend command
5299 * if the temperature value is higher than this threshold.
5302 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH
,
5303 /* FW reports temperature data periodically at this interval (ms).
5306 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE
,
5309 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST
,
5310 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX
=
5311 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST
- 1,
5315 * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to
5316 * report thermal events from driver to user space.
5317 * enum values are used for NL attributes for data used by
5318 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command.
5320 enum qca_wlan_vendor_attr_thermal_event
{
5321 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID
= 0,
5322 /* Temperature value (degree Celsius) from driver.
5325 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE
,
5326 /* Indication of resume completion from power save mode.
5327 * NLA_FLAG attribute.
5329 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE
,
5332 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST
,
5333 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX
=
5334 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST
- 1,
5338 * enum he_fragmentation_val - HE fragmentation support values
5339 * Indicates level of dynamic fragmentation that is supported by
5340 * a STA as a recipient.
5341 * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2
5342 * (HE MAC Capabilities Information field) and are used in HE Capabilities
5343 * element to advertise the support. These values are validated in the driver
5344 * to check the device capability and advertised in the HE Capabilities
5345 * element. These values are used to configure testbed device to allow the
5346 * advertised hardware capabilities to be downgraded for testing purposes.
5348 * @HE_FRAG_DISABLE: no support for dynamic fragmentation
5349 * @HE_FRAG_LEVEL1: support for dynamic fragments that are
5350 * contained within an MPDU or S-MPDU, no support for dynamic fragments
5351 * within an A-MPDU that is not an S-MPDU.
5352 * @HE_FRAG_LEVEL2: support for dynamic fragments that are
5353 * contained within an MPDU or S-MPDU and support for up to one dynamic
5354 * fragment for each MSDU, each A-MSDU if supported by the recipient, and
5355 * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an
5357 * @HE_FRAG_LEVEL3: support for dynamic fragments that are
5358 * contained within an MPDU or S-MPDU and support for multiple dynamic
5359 * fragments for each MSDU and for each A-MSDU if supported by the
5360 * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic
5361 * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU.
5363 enum he_fragmentation_val
{
5371 * enum he_mcs_config - HE MCS support configuration
5373 * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth.
5374 * These values are used in driver to configure the HE MCS map to advertise
5375 * Tx/Rx MCS map in HE capability and these values are applied for all the
5376 * streams supported by the device. To configure MCS for different bandwidths,
5377 * vendor command needs to be sent using this attribute with appropriate value.
5378 * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS
5379 * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11
5380 * send this command using HE MCS config attribute with value HE_160_MCS0_11.
5381 * These values are used to configure testbed device to allow the advertised
5382 * hardware capabilities to be downgraded for testing purposes. The enum values
5383 * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and
5384 * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map.
5385 * These values are validated in the driver before setting the MCS map and
5386 * driver returns error if the input is other than these enum values.
5388 * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7
5389 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9
5390 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11
5391 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7
5392 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9
5393 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11
5394 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7
5395 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9
5396 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11
5398 enum he_mcs_config
{
5405 HE_80P80_MCS0_7
= 8,
5406 HE_80P80_MCS0_9
= 9,
5407 HE_80P80_MCS0_11
= 10,
5411 * enum qca_wlan_ba_session_config - BA session configuration
5413 * Indicates the configuration values for BA session configuration attribute.
5415 * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration.
5416 * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID.
5418 enum qca_wlan_ba_session_config
{
5419 QCA_WLAN_ADD_BA
= 1,
5420 QCA_WLAN_DELETE_BA
= 2,
5424 * enum qca_wlan_ac_type - Access category type
5426 * Indicates the access category type value.
5428 * @QCA_WLAN_AC_BE: BE access category
5429 * @QCA_WLAN_AC_BK: BK access category
5430 * @QCA_WLAN_AC_VI: VI access category
5431 * @QCA_WLAN_AC_VO: VO access category
5432 * @QCA_WLAN_AC_ALL: All ACs
5434 enum qca_wlan_ac_type
{
5439 QCA_WLAN_AC_ALL
= 4,
5443 * enum qca_wlan_he_ltf_cfg - HE LTF configuration
5445 * Indicates the HE LTF configuration value.
5447 * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF,
5448 * based on the GI setting
5449 * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF
5450 * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF
5451 * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF
5453 enum qca_wlan_he_ltf_cfg
{
5454 QCA_WLAN_HE_LTF_AUTO
= 0,
5455 QCA_WLAN_HE_LTF_1X
= 1,
5456 QCA_WLAN_HE_LTF_2X
= 2,
5457 QCA_WLAN_HE_LTF_4X
= 3,
5461 * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration
5463 * Indicates the HE trigger frame MAC padding duration value.
5465 * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to
5466 * process the trigger frame.
5467 * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for
5469 * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for
5472 enum qca_wlan_he_mac_padding_dur
{
5473 QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME
= 0,
5474 QCA_WLAN_HE_8US_OF_PROCESS_TIME
= 1,
5475 QCA_WLAN_HE_16US_OF_PROCESS_TIME
= 2,
5479 * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration
5481 * Indicates the HE Operating mode control channel width setting value.
5483 * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz
5484 * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz
5485 * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz
5486 * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz
5488 enum qca_wlan_he_om_ctrl_ch_bw
{
5489 QCA_WLAN_HE_OM_CTRL_BW_20M
= 0,
5490 QCA_WLAN_HE_OM_CTRL_BW_40M
= 1,
5491 QCA_WLAN_HE_OM_CTRL_BW_80M
= 2,
5492 QCA_WLAN_HE_OM_CTRL_BW_160M
= 3,
5495 /* Attributes for data used by
5496 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
5498 enum qca_wlan_vendor_attr_wifi_test_config
{
5499 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID
= 0,
5500 /* 8-bit unsigned value to configure the driver to enable/disable
5501 * WMM feature. This attribute is used to configure testbed device.
5502 * 1-enable, 0-disable
5504 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE
= 1,
5506 /* 8-bit unsigned value to configure the driver to accept/reject
5507 * the addba request from peer. This attribute is used to configure
5508 * the testbed device.
5509 * 1-accept addba, 0-reject addba
5511 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ
= 2,
5513 /* 8-bit unsigned value to configure the driver to send or not to
5514 * send the addba request to peer.
5515 * This attribute is used to configure the testbed device.
5516 * 1-send addba, 0-do not send addba
5518 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ
= 3,
5520 /* 8-bit unsigned value to indicate the HE fragmentation support.
5521 * Uses enum he_fragmentation_val values.
5522 * This attribute is used to configure the testbed device to
5523 * allow the advertised hardware capabilities to be downgraded
5524 * for testing purposes.
5526 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION
= 4,
5528 /* 8-bit unsigned value to indicate the HE MCS support.
5529 * Uses enum he_mcs_config values.
5530 * This attribute is used to configure the testbed device to
5531 * allow the advertised hardware capabilities to be downgraded
5532 * for testing purposes.
5534 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS
= 5,
5536 /* 8-bit unsigned value to configure the driver to allow or not to
5537 * allow the connection with WEP/TKIP in HT/VHT/HE modes.
5538 * This attribute is used to configure the testbed device.
5539 * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP.
5541 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE
= 6,
5543 /* 8-bit unsigned value to configure the driver to add a
5544 * new BA session or delete the existing BA session for
5545 * given TID. ADDBA command uses the buffer size and TID
5546 * configuration if user specifies the values else default
5547 * value for buffer size is used for all TIDs if the TID
5548 * also not specified. For DEL_BA command TID value is
5549 * required to process the command.
5550 * Uses enum qca_wlan_ba_session_config values.
5551 * This attribute is used to configure the testbed device.
5553 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION
= 7,
5555 /* 16-bit unsigned value to configure the buffer size in addba
5556 * request and response frames.
5557 * This attribute is used to configure the testbed device.
5558 * The range of the value is 0 to 256.
5560 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE
= 8,
5562 /* 8-bit unsigned value to configure the buffer size in addba
5563 * request and response frames.
5564 * This attribute is used to configure the testbed device.
5566 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID
= 9,
5568 /* 8-bit unsigned value to configure the no ack policy.
5569 * To configure no ack policy, access category value is
5570 * required to process the command.
5571 * This attribute is used to configure the testbed device.
5572 * 1 - enable no ack, 0 - disable no ack.
5574 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK
= 10,
5576 /* 8-bit unsigned value to configure the AC for no ack policy
5577 * This attribute is used to configure the testbed device.
5578 * Uses the enum qca_wlan_ac_type values.
5580 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC
= 11,
5582 /* 8-bit unsigned value to configure the HE LTF
5583 * This attribute is used to configure the testbed device.
5584 * Uses the enum qca_wlan_he_ltf_cfg values.
5586 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF
= 12,
5588 /* 8-bit unsigned value to configure the tx beamformee.
5589 * This attribute is used to configure the testbed device.
5590 * 1-enable, 0-disable.
5592 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE
= 13,
5594 /* 8-bit unsigned value to configure the tx beamformee number
5595 * of space-time streams.
5596 * This attribute is used to configure the testbed device.
5597 * The range of the value is 0 to 8.
5599 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS
= 14,
5601 /* 8-bit unsigned value to configure the MU EDCA params for given AC
5602 * This attribute is used to configure the testbed device.
5603 * Uses the enum qca_wlan_ac_type values.
5605 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC
= 15,
5607 /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC
5608 * To configure MU EDCA AIFSN value, MU EDCA access category value
5609 * is required to process the command.
5610 * This attribute is used to configure the testbed device.
5612 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN
= 16,
5614 /* 8-bit unsigned value to configure the MU EDCA ECW min value for
5616 * To configure MU EDCA ECW min value, MU EDCA access category value
5617 * is required to process the command.
5618 * This attribute is used to configure the testbed device.
5620 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN
= 17,
5622 /* 8-bit unsigned value to configure the MU EDCA ECW max value for
5624 * To configure MU EDCA ECW max value, MU EDCA access category value
5625 * is required to process the command.
5626 * This attribute is used to configure the testbed device.
5628 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX
= 18,
5630 /* 8-bit unsigned value to configure the MU EDCA timer for given AC
5631 * To configure MU EDCA timer value, MU EDCA access category value
5632 * is required to process the command.
5633 * This attribute is used to configure the testbed device.
5635 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER
= 19,
5637 /* 8-bit unsigned value to configure the HE trigger frame MAC padding
5639 * This attribute is used to configure the testbed device.
5640 * Uses the enum qca_wlan_he_mac_padding_dur values.
5642 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR
= 20,
5644 /* 8-bit unsigned value to override the MU EDCA params to defaults
5645 * regardless of the AP beacon MU EDCA params. If it is enabled use
5646 * the default values else use the MU EDCA params from AP beacon.
5647 * This attribute is used to configure the testbed device.
5648 * 1-enable, 0-disable.
5650 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA
= 21,
5652 /* 8-bit unsigned value to configure the support for receiving
5653 * an MPDU that contains an operating mode control subfield.
5654 * This attribute is used to configure the testbed device.
5655 * 1-enable, 0-disable.
5657 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP
= 22,
5659 /* Nested attribute values required to setup the TWT session.
5660 * enum qca_wlan_vendor_attr_twt_setup provides the necessary
5661 * information to set up the session. It contains broadcast flags,
5662 * set_up flags, trigger value, flow type, flow ID, wake interval
5663 * exponent, protection, target wake time, wake duration, wake interval
5664 * mantissa. These nested attributes are used to setup a host triggered
5667 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP
= 23,
5669 /* This nested attribute is used to terminate the current TWT session.
5670 * It does not currently carry any attributes.
5672 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE
= 24,
5674 /* This nested attribute is used to suspend the current TWT session.
5675 * It does not currently carry any attributes.
5677 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND
= 25,
5679 /* Nested attribute values to indicate the request for resume.
5680 * This attribute is used to resume the TWT session.
5681 * enum qca_wlan_vendor_attr_twt_resume provides the necessary
5682 * parameters required to resume the TWT session.
5684 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME
= 26,
5686 /* 8-bit unsigned value to set the HE operating mode control
5687 * (OM CTRL) Channel Width subfield.
5688 * The Channel Width subfield indicates the operating channel width
5689 * supported by the STA for both reception and transmission.
5690 * Uses the enum qca_wlan_he_om_ctrl_ch_bw values.
5691 * This setting is cleared with the
5692 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
5693 * flag attribute to reset defaults.
5694 * This attribute is used to configure the testbed device.
5696 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW
= 27,
5698 /* 8-bit unsigned value to configure the number of spatial
5699 * streams in HE operating mode control field.
5700 * This setting is cleared with the
5701 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
5702 * flag attribute to reset defaults.
5703 * This attribute is used to configure the testbed device.
5705 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS
= 28,
5707 /* Flag attribute to configure the UL MU disable bit in
5708 * HE operating mode control field.
5709 * This setting is cleared with the
5710 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
5711 * flag attribute to reset defaults.
5712 * This attribute is used to configure the testbed device.
5714 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE
= 29,
5716 /* Flag attribute to clear the previously set HE operating mode
5717 * control field configuration.
5718 * This attribute is used to configure the testbed device to reset
5719 * defaults to clear any previously set HE operating mode control
5720 * field configuration.
5722 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG
= 30,
5724 /* 8-bit unsigned value to configure HE single user PPDU
5725 * transmission. By default this setting is disabled and it
5726 * is disabled in the reset defaults of the device configuration.
5727 * This attribute is used to configure the testbed device.
5728 * 1-enable, 0-disable
5730 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU
= 31,
5732 /* 8-bit unsigned value to configure action frame transmission
5733 * in HE trigger based PPDU transmission.
5734 * By default this setting is disabled and it is disabled in
5735 * the reset defaults of the device configuration.
5736 * This attribute is used to configure the testbed device.
5737 * 1-enable, 0-disable
5739 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU
= 32,
5742 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST
,
5743 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX
=
5744 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST
- 1,
5748 * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command
5749 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5750 * The user can add/delete the filter by specifying the BSSID/STA MAC address in
5751 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in
5752 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in
5753 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the
5754 * statistics of an unassociated station by specifying the MAC address in
5755 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in
5756 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in
5757 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get
5758 * the statistics of all unassociated stations by specifying the Broadcast MAC
5759 * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with
5760 * above procedure. In the response, driver shall specify statistics
5761 * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS.
5763 enum qca_wlan_vendor_attr_bss_filter
{
5764 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID
= 0,
5765 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR
= 1,
5766 /* Other BSS filter type, unsigned 8 bit value. One of the values
5767 * in enum qca_wlan_vendor_bss_filter_type.
5769 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE
= 2,
5770 /* Other BSS filter action, unsigned 8 bit value. One of the values
5771 * in enum qca_wlan_vendor_bss_filter_action.
5773 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION
= 3,
5774 /* Array of nested attributes where each entry is the statistics
5775 * information of the specified station that belong to another BSS.
5776 * Attributes for each entry are taken from enum
5777 * qca_wlan_vendor_bss_filter_sta_stats.
5778 * Other BSS station configured in
5779 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type
5780 * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA.
5781 * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER
5782 * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET.
5784 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS
= 4,
5787 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST
,
5788 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX
=
5789 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST
- 1,
5793 * enum qca_wlan_vendor_bss_filter_type - Type of
5794 * filter used in other BSS filter operations. Used by the vendor command
5795 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5797 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter
5798 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter
5800 enum qca_wlan_vendor_bss_filter_type
{
5801 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID
,
5802 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA
,
5806 * enum qca_wlan_vendor_bss_filter_action - Type of
5807 * action in other BSS filter operations. Used by the vendor command
5808 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5810 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter
5811 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter
5812 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics
5814 enum qca_wlan_vendor_bss_filter_action
{
5815 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD
,
5816 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL
,
5817 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET
,
5821 * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for
5822 * the statistics of a specific unassociated station belonging to another BSS.
5823 * The statistics provides information of the unassociated station
5824 * filtered by other BSS operation - such as MAC, signal value.
5825 * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5827 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station.
5828 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength
5829 * of the station. Unsigned 8 bit number containing RSSI.
5830 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host
5831 * driver for the last received RSSI. Unsigned 64 bit number containing
5832 * nanoseconds from the boottime.
5834 enum qca_wlan_vendor_bss_filter_sta_stats
{
5835 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID
= 0,
5836 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC
= 1,
5837 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI
= 2,
5838 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS
= 3,
5841 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST
,
5842 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX
=
5843 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST
- 1
5846 /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute
5847 * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command
5848 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT.
5850 enum qca_wlan_nan_ext_subcmd_type
{
5851 /* Subcmd of type NAN Enable Request */
5852 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ
= 1,
5853 /* Subcmd of type NAN Disable Request */
5854 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ
= 2,
5858 * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command
5859 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT.
5861 enum qca_wlan_vendor_attr_nan_params
{
5862 QCA_WLAN_VENDOR_ATTR_NAN_INVALID
= 0,
5863 /* Carries NAN command for firmware component. Every vendor command
5864 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a
5865 * payload containing the NAN command. NLA_BINARY attribute.
5867 QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA
= 1,
5868 /* Indicates the type of NAN command sent with
5869 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type
5870 * describes the possible range of values. This attribute is mandatory
5871 * if the command being issued is either
5872 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or
5873 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute.
5875 QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE
= 2,
5876 /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz
5877 * band. This attribute is mandatory when command type is
5878 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute.
5880 QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ
= 3,
5881 /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz
5882 * band. This attribute is optional and should be included when command
5883 * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery
5884 * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute.
5886 QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ
= 4,
5889 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST
,
5890 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX
=
5891 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST
- 1
5895 * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for
5896 * TWT (Target Wake Time) setup request. These attributes are sent as part of
5897 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and
5898 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
5900 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute.
5901 * Disable (flag attribute not present) - Individual TWT
5902 * Enable (flag attribute present) - Broadcast TWT.
5903 * Individual means the session is between the STA and the AP.
5904 * This session is established using a separate negotiation between
5906 * Broadcast means the session is across multiple STAs and an AP. The
5907 * configuration parameters are announced in Beacon frames by the AP.
5909 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8).
5910 * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to
5911 * specify the TWT request type
5913 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute
5914 * Enable (flag attribute present) - TWT with trigger support.
5915 * Disable (flag attribute not present) - TWT without trigger support.
5916 * Trigger means the AP will send the trigger frame to allow STA to send data.
5917 * Without trigger, the STA will wait for the MU EDCA timer before
5918 * transmitting the data.
5920 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8)
5921 * 0 - Announced TWT - In this mode, STA may skip few service periods to
5922 * save more power. If STA wants to wake up, it will send a PS-POLL/QoS
5924 * 1 - Unannounced TWT - The STA will wakeup during every SP.
5926 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8)
5927 * Flow ID is the unique identifier for each TWT session.
5928 * Currently this is not required and dialog ID will be set to zero.
5930 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8)
5931 * This attribute (exp) is used along with the mantissa to derive the
5932 * wake interval using the following formula:
5933 * pow(2,exp) = wake_intvl_us/wake_intvl_mantis
5934 * Wake interval is the interval between 2 successive SP.
5936 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute
5937 * Enable (flag attribute present) - Protection required.
5938 * Disable (flag attribute not present) - Protection not required.
5939 * If protection is enabled, then the AP will use protection
5940 * mechanism using RTS/CTS to self to reserve the airtime.
5942 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32)
5943 * This attribute is used as the SP offset which is the offset from
5944 * TSF after which the wake happens. The units are in microseconds. If
5945 * this attribute is not provided, then the value will be set to zero.
5947 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32)
5948 * This is the duration of the service period. The units are in TU.
5950 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32)
5951 * This attribute is used to configure wake interval mantissa.
5952 * The units are in TU.
5954 enum qca_wlan_vendor_attr_twt_setup
{
5955 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID
= 0,
5956 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST
= 1,
5957 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE
= 2,
5958 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER
= 3,
5959 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE
= 4,
5960 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID
= 5,
5961 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP
= 6,
5962 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION
= 7,
5963 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME
= 8,
5964 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION
= 9,
5965 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA
= 10,
5968 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST
,
5969 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX
=
5970 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST
- 1,
5974 * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for
5975 * TWT (Target Wake Time) resume request. These attributes are sent as part of
5976 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and
5977 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
5979 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8)
5980 * This attribute is used as the SP offset which is the offset from
5981 * TSF after which the wake happens. The units are in microseconds.
5982 * If this attribute is not provided, then the value will be set to
5985 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32)
5986 * This attribute represents the next TWT subfield size.
5988 enum qca_wlan_vendor_attr_twt_resume
{
5989 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID
= 0,
5990 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT
= 1,
5991 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE
= 2,
5994 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST
,
5995 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX
=
5996 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST
- 1,
6000 * enum qca_wlan_vendor_twt_setup_req_type - Required (u8)
6001 * Represents the setup type being requested for TWT.
6002 * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT
6003 * parameters but relying on AP to fill the parameters during the negotiation.
6004 * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested
6005 * values which the AP may accept or AP may provide alternative parameters
6006 * which the STA may accept.
6007 * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any
6008 * alternate parameters than the requested ones.
6010 enum qca_wlan_vendor_twt_setup_req_type
{
6011 QCA_WLAN_VENDOR_TWT_SETUP_REQUEST
= 1,
6012 QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST
= 2,
6013 QCA_WLAN_VENDOR_TWT_SETUP_DEMAND
= 3,
6017 * enum qca_wlan_roam_scan_event_type - Type of roam scan event
6019 * Indicates the type of roam scan event sent by firmware/driver.
6021 * @QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT: Roam scan trigger event type.
6022 * @QCA_WLAN_ROAM_SCAN_STOP_EVENT: Roam scan stopped event type.
6024 enum qca_wlan_roam_scan_event_type
{
6025 QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT
= 0,
6026 QCA_WLAN_ROAM_SCAN_STOP_EVENT
= 1,
6030 * enum qca_wlan_roam_scan_trigger_reason - Roam scan trigger reason
6032 * Indicates the reason for triggering roam scan by firmware/driver.
6034 * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI: Due to low RSSI of current AP.
6035 * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER: Due to high packet error rate.
6037 enum qca_wlan_roam_scan_trigger_reason
{
6038 QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI
= 0,
6039 QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER
= 1,
6043 * enum qca_wlan_vendor_attr_roam_scan - Vendor subcmd attributes to report
6044 * roam scan related details from driver/firmware to user space. enum values
6045 * are used for NL attributes sent with
6046 * %QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT sub command.
6048 enum qca_wlan_vendor_attr_roam_scan
{
6049 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_INVALID
= 0,
6050 /* Encapsulates type of roam scan event being reported. enum
6051 * qca_wlan_roam_scan_event_type describes the possible range of
6052 * values. u32 attribute.
6054 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_EVENT_TYPE
= 1,
6055 /* Encapsulates reason for triggering roam scan. enum
6056 * qca_wlan_roam_scan_trigger_reason describes the possible range of
6057 * values. u32 attribute.
6059 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_TRIGGER_REASON
= 2,
6062 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST
,
6063 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_MAX
=
6064 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST
- 1,
6068 * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by
6069 * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor
6070 * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG.
6072 enum qca_wlan_vendor_cfr_method
{
6073 /* CFR method using QOS Null frame */
6074 QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL
= 0,
6078 * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command
6079 * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer
6080 * Channel Frequency Response capture parameters and enable periodic CFR
6083 enum qca_wlan_vendor_peer_cfr_capture_attr
{
6084 QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID
= 0,
6085 /* 6-byte MAC address of the peer.
6086 * This attribute is mandatory.
6088 QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR
= 1,
6089 /* Enable peer CFR Capture, flag attribute.
6090 * This attribute is mandatory to enable peer CFR capture.
6091 * If this attribute is not present, peer CFR capture is disabled.
6093 QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE
= 2,
6094 /* BW of measurement, attribute uses the values in enum nl80211_chan_width
6095 * Supported values: 20, 40, 80, 80+80, 160.
6096 * Note that all targets may not support all bandwidths.
6097 * u8 attribute. This attribute is mandatory if attribute
6098 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
6100 QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH
= 3,
6101 /* Periodicity of CFR measurement in msec.
6102 * Periodicity should be a multiple of Base timer.
6103 * Current Base timer value supported is 10 msecs (default).
6104 * 0 for one shot capture. u32 attribute.
6105 * This attribute is mandatory if attribute
6106 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
6108 QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY
= 4,
6109 /* Method used to capture Channel Frequency Response.
6110 * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method.
6111 * u8 attribute. This attribute is mandatory if attribute
6112 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
6114 QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD
= 5,
6115 /* Enable periodic CFR capture, flag attribute.
6116 * This attribute is mandatory to enable Periodic CFR capture.
6117 * If this attribute is not present, periodic CFR capture is disabled.
6119 QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE
= 6,
6122 QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST
,
6123 QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX
=
6124 QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST
- 1,
6128 * enum qca_wlan_throughput_level - Current throughput level
6130 * Indicates the current level of throughput calculated by the driver. The
6131 * driver may choose different thresholds to decide whether the throughput level
6132 * is low or medium or high based on variety of parameters like physical link
6133 * capacity of the current connection, the number of packets being dispatched
6134 * per second, etc. The throughput level events might not be consistent with the
6135 * actual current throughput value being observed.
6137 * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput
6138 * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput
6139 * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput
6141 enum qca_wlan_throughput_level
{
6142 QCA_WLAN_THROUGHPUT_LEVEL_LOW
= 0,
6143 QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM
= 1,
6144 QCA_WLAN_THROUGHPUT_LEVEL_HIGH
= 2,
6148 * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to
6149 * report throughput changes from the driver to user space. enum values are used
6150 * for netlink attributes sent with
6151 * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command.
6153 enum qca_wlan_vendor_attr_throughput_change
{
6154 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID
= 0,
6155 /* Indicates the direction of throughput in which the change is being
6156 * reported. u8 attribute. Value is 0 for TX and 1 for RX.
6158 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION
= 1,
6159 /* Indicates the newly observed throughput level. enum
6160 * qca_wlan_throughput_level describes the possible range of values.
6163 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL
= 2,
6164 /* Indicates the driver's guidance on the new value to be set to
6165 * kernel's TCP parameter tcp_limit_output_bytes. u32 attribute. The
6166 * driver may optionally include this attribute.
6168 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES
= 3,
6169 /* Indicates the driver's guidance on the new value to be set to
6170 * kernel's TCP parameter tcp_adv_win_scale. s8 attribute. Possible
6171 * values are from -31 to 31. The driver may optionally include this
6174 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE
= 4,
6175 /* Indicates the driver's guidance on the new value to be set to
6176 * kernel's TCP parameter tcp_delack_seg. u32 attribute. The driver may
6177 * optionally include this attribute.
6179 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG
= 5,
6182 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST
,
6183 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX
=
6184 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST
- 1,
6188 * enum qca_coex_config_profiles - This enum defines different types of
6189 * traffic streams that can be prioritized one over the other during coex
6191 * The types defined in this enum are categorized in the below manner.
6192 * 0 - 31 values corresponds to WLAN
6193 * 32 - 63 values corresponds to BT
6194 * 64 - 95 values corresponds to Zigbee
6195 * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA
6196 * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA
6197 * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA
6198 * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA
6199 * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA
6200 * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP
6201 * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP
6202 * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP
6203 * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP
6204 * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP
6205 * @QCA_BT_A2DP: Prioritize BT A2DP
6206 * @QCA_BT_BLE: Prioritize BT BLE
6207 * @QCA_BT_SCO: Prioritize BT SCO
6208 * @QCA_ZB_LOW: Prioritize Zigbee Low
6209 * @QCA_ZB_HIGH: Prioritize Zigbee High
6211 enum qca_coex_config_profiles
{
6212 /* 0 - 31 corresponds to WLAN */
6213 QCA_WIFI_STA_DISCOVERY
= 0,
6214 QCA_WIFI_STA_CONNECTION
= 1,
6215 QCA_WIFI_STA_CLASS_3_MGMT
= 2,
6216 QCA_WIFI_STA_DATA
= 3,
6217 QCA_WIFI_STA_ALL
= 4,
6218 QCA_WIFI_SAP_DISCOVERY
= 5,
6219 QCA_WIFI_SAP_CONNECTION
= 6,
6220 QCA_WIFI_SAP_CLASS_3_MGMT
= 7,
6221 QCA_WIFI_SAP_DATA
= 8,
6222 QCA_WIFI_SAP_ALL
= 9,
6223 /* 32 - 63 corresponds to BT */
6227 /* 64 - 95 corresponds to Zigbee */
6233 * enum qca_vendor_attr_coex_config - Specifies vendor coex config attributes
6235 * @QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES: This attribute contains variable
6236 * length array of 8-bit values from enum qca_coex_config_profiles.
6237 * FW will prioritize the profiles in the order given in the array encapsulated
6238 * in this attribute.
6240 * -----------------------------------------------------------------------
6241 * | 1 | 34 | 32 | 65 |
6242 * -----------------------------------------------------------------------
6243 * If the attribute contains the values defined in above array then it means
6244 * 1) Wifi STA connection has priority over BT_SCO, BT_A2DP and ZIGBEE HIGH.
6245 * 2) BT_SCO has priority over BT_A2DP.
6246 * 3) BT_A2DP has priority over ZIGBEE HIGH.
6247 * Profiles which are not listed in this array shall not be preferred over the
6248 * profiles which are listed in the array as a part of this attribute.
6250 enum qca_vendor_attr_coex_config
{
6251 QCA_VENDOR_ATTR_COEX_CONFIG_INVALID
= 0,
6252 QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES
= 1,
6255 QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST
,
6256 QCA_VENDOR_ATTR_COEX_CONFIG_MAX
=
6257 QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST
- 1,
6261 * enum qca_wlan_vendor_attr_link_properties - Represent the link properties.
6263 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC address of the peer
6264 * (STA/AP) for the connected link.
6265 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a
6266 * &struct nl80211_sta_flag_update for the respective connected link. MAC
6267 * address of the peer represented by
6268 * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR.
6270 enum qca_wlan_vendor_attr_link_properties
{
6271 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID
= 0,
6272 /* 1 - 3 are reserved */
6273 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR
= 4,
6274 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS
= 5,
6277 QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST
,
6278 QCA_VENDOR_ATTR_LINK_PROPERTIES_MAX
=
6279 QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST
- 1,
6282 #endif /* QCA_VENDOR_H */