2 * Qualcomm Atheros OUI and vendor specific assignments
3 * Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
4 * Copyright (c) 2018, The Linux Foundation
6 * This software may be distributed under the terms of the BSD license.
7 * See README for more details.
14 * This file is a registry of identifier assignments from the Qualcomm Atheros
15 * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers
16 * can be assigned through normal review process for changes to the upstream
17 * hostap.git repository.
20 #define OUI_QCA 0x001374
23 * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs
25 enum qca_radiotap_vendor_ids
{
26 QCA_RADIOTAP_VID_WLANTEST
= 0,
30 * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers
32 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0
34 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event
36 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use
37 * internal BSS-selection. This command uses
38 * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy
39 * for the current connection (i.e., changes policy set by the nl80211
40 * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be
41 * included to indicate which BSS to use in case roaming is disabled.
43 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency
44 * ranges to avoid to reduce issues due to interference or internal
45 * co-existence information in the driver. The event data structure is
46 * defined in struct qca_avoid_freq_list.
48 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support
51 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass
52 * NAN Request/Response and NAN Indication messages. These messages are
53 * interpreted between the framework and the firmware component.
55 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be
56 * used to configure PMK to the driver even when not connected. This can
57 * be used to request offloading of key management operations. Only used
58 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
60 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of
61 * NL80211_CMD_ROAM event with optional attributes including information
62 * from offloaded key management operation. Uses
63 * enum qca_wlan_vendor_attr_roam_auth attributes. Only used
64 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD.
66 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to
67 * invoke the ACS function in device and pass selected channels to
70 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features
71 * supported by the driver. enum qca_wlan_vendor_features defines
72 * the possible features.
74 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver,
75 * which supports DFS offloading, to indicate a channel availability check
78 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver,
79 * which supports DFS offloading, to indicate a channel availability check
82 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver,
83 * which supports DFS offloading, to indicate that the channel availability
84 * check aborted, no change to the channel status.
86 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by
87 * driver, which supports DFS offloading, to indicate that the
88 * Non-Occupancy Period for this channel is over, channel becomes usable.
90 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver,
91 * which supports DFS offloading, to indicate a radar pattern has been
92 * detected. The channel is now unusable.
94 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap
95 * based on enum wifi_logger_supported_features. Attributes defined in
96 * enum qca_wlan_vendor_attr_get_logger_features.
98 * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular
99 * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the
100 * attribute for this command. Attributes defined in
101 * enum qca_wlan_vendor_attr_wifi_logger_start.
103 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS
104 * capabilities of the driver, parameters includes the attributes defined
105 * in enum qca_wlan_vendor_attr_tdls_get_capabilities.
107 * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload
108 * sending of certain periodic IP packet to firmware, attributes defined in
109 * enum qca_wlan_vendor_attr_offloaded_packets.
111 * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI
112 * monitoring, defines min and max RSSI which are configured for RSSI
113 * monitoring. Also used to notify the RSSI breach and provides the BSSID
114 * and RSSI value that was breached. Attributes defined in
115 * enum qca_wlan_vendor_attr_rssi_monitoring.
117 * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN
118 * Data Path (NDP) related operations, attributes defined in
119 * enum qca_wlan_vendor_attr_ndp_params.
121 * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable
122 * Neighbour Discovery offload, attributes defined in
123 * enum qca_wlan_vendor_attr_nd_offload.
125 * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various
126 * configuration parameter for BPF packet filter, attributes defined in
127 * enum qca_wlan_vendor_attr_packet_filter.
129 * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware
130 * maximum supported size, attributes defined in
131 * enum qca_wlan_vendor_drv_info.
133 * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various
134 * data about wake reasons and datapath IP statistics, attributes defined
135 * in enum qca_wlan_vendor_attr_wake_stats.
137 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration
138 * for IEEE 802.11 communicating outside the context of a basic service
139 * set, called OCB command. Uses the attributes defines in
140 * enum qca_wlan_vendor_attr_ocb_set_config.
142 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB
143 * UTC time. Use the attributes defines in
144 * enum qca_wlan_vendor_attr_ocb_set_utc_time.
146 * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start
147 * sending OCB timing advert frames. Uses the attributes defines in
148 * enum qca_wlan_vendor_attr_ocb_start_timing_advert.
150 * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop
151 * OCB timing advert. Uses the attributes defines in
152 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert.
154 * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF
155 * timer value. Uses the attributes defines in
156 * enum qca_wlan_vendor_attr_ocb_get_tsf_resp.
158 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
159 * start the P2P Listen offload function in device and pass the listen
160 * channel, period, interval, count, device types, and vendor specific
161 * information elements to the device driver and firmware.
162 * Uses the attributes defines in
163 * enum qca_wlan_vendor_attr_p2p_listen_offload.
165 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to
166 * indicate stop request/response of the P2P Listen offload function in
167 * device. As an event, it indicates either the feature stopped after it
168 * was already running or feature has actually failed to start. Uses the
169 * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
171 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
172 * beaconing, this sub command provides the driver, the frequencies on the
173 * 5 GHz band to check for any radar activity. Driver selects one channel
174 * from this priority list provided through
175 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
176 * to check for radar activity on it. If no radar activity is detected
177 * during the channel availability check period, driver internally switches
178 * to the selected frequency of operation. If the frequency is zero, driver
179 * internally selects a channel. The status of this conditional switch is
180 * indicated through an event using the same sub command through
181 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
182 * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
184 * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
185 * attributes defined in enum qca_wlan_gpio_attr.
187 * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
188 * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
189 * capabilities are to be fetched and other
190 * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
191 * requested capabilities.
193 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
194 * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
197 * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for
198 * indoor location features. Capabilities are reported in
199 * QCA_WLAN_VENDOR_ATTR_LOC_CAPA.
201 * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM
202 * (fine timing measurement) session with one or more peers.
203 * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and
204 * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS.
205 * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
206 * events will be reported, followed by
207 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate
209 * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6
211 * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session.
212 * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with
213 * status code indicating session was aborted.
215 * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement
216 * results for one peer. Results are reported in
217 * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS.
219 * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when
220 * FTM session is finished, either successfully or aborted by
223 * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder
224 * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether
225 * to enable or disable the responder. LCI/LCR reports can be
226 * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and
227 * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple
228 * times to update the LCI/LCR reports.
230 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of
231 * arrival) measurement with a single peer. Specify peer MAC address in
232 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in
233 * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel
234 * scan results cache and use the frequency from there).
235 * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE.
236 * Measurement result is reported in
237 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event.
239 * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify
240 * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
242 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports
243 * the AOA measurement result.
244 * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
245 * success/failure status is reported in
246 * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS.
247 * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
248 * The antenna array(s) used in the measurement are reported in
249 * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK.
251 * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given
252 * data as per the given parameters.
254 * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a
257 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level
258 * configuration for a DMG RF sector. Specify sector index in
259 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
260 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules
261 * to return sector information for in
262 * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration
263 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the
264 * exact time where information was captured in
265 * QCA_WLAN_VENDOR_ATTR_TSF.
267 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level
268 * configuration for a DMG RF sector. Specify sector index in
269 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
270 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration
271 * for one or more DMG RF modules in
272 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG.
274 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected
275 * DMG RF sector for a station. This is the sector that the HW
276 * will use to communicate with the station. Specify the MAC address
277 * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not
278 * needed for unassociated station). Specify sector type to return in
279 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected
280 * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
281 * Also return the exact time where the information was captured
282 * in QCA_WLAN_VENDOR_ATTR_TSF.
284 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the
285 * selected DMG RF sector for a station. This is the sector that
286 * the HW will use to communicate with the station.
287 * Specify the MAC address of associated station/AP/PCP in
288 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in
289 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index
290 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
291 * The selected sector will be locked such that it will not be
292 * modified like it normally does (for example when station
293 * moves around). To unlock the selected sector for a station
294 * pass the special value 0xFFFF in the sector index. To unlock
295 * all connected stations also pass a broadcast MAC address.
297 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior
298 * in the host driver. The different TDLS configurations are defined
299 * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration.
301 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE
302 * capabilities. The response uses the attributes defined in
303 * enum qca_wlan_vendor_attr_get_he_capabilities.
305 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was
306 * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
307 * carries the scan cookie of the corresponding scan request. The scan
308 * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
310 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
311 * Absorption Rate (SAR) power limits. A critical regulation for
312 * FCC compliance, OEMs require methods to set SAR limits on TX
313 * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
314 * attributes are used with this command.
316 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the
317 * host driver for offloading the implementation of Auto Channel Selection
318 * (ACS) to an external user space entity. This interface is used as the
319 * event from the host driver to the user space entity and also as the
320 * request from the user space entity to the host driver. The event from
321 * the host driver is used by the user space entity as an indication to
322 * start the ACS functionality. The attributes used by this event are
323 * represented by the enum qca_wlan_vendor_attr_external_acs_event.
324 * User space entity uses the same interface to inform the host driver with
325 * selected channels after the ACS operation using the attributes defined
326 * by enum qca_wlan_vendor_attr_external_acs_channels.
328 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the
329 * requisite information leading to a power save failure. The information
330 * carried as part of this event is represented by the
331 * enum qca_attr_chip_power_save_failure attributes.
333 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics
334 * collection. Uses attributes defined in enum qca_attr_nud_stats_set.
336 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These
337 * statistics are represented by the enum qca_attr_nud_stats_get
340 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch
341 * the BSS transition status, whether accept or reject, for a list of
342 * candidate BSSIDs provided by the userspace. This uses the vendor
343 * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and
344 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify
345 * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an
346 * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in
347 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response
348 * the driver shall specify array of
349 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and
350 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in
351 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO.
353 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a
354 * specific QCA module. The trace levels are represented by
355 * enum qca_attr_trace_level attributes.
357 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement
358 * Protocol antenna limit in different modes. See enum
359 * qca_wlan_vendor_attr_brp_ant_limit_mode.
361 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan
362 * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan.
363 * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE)
364 * identifying the operation in success case.
366 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses
367 * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from
368 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to
371 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the
372 * specific interface. This can be used to modify some of the low level
373 * scan parameters (off channel dwell time, home channel time) in the
374 * driver/firmware. These parameters are maintained within the host driver.
375 * This command is valid only when the interface is in the connected state.
376 * These scan parameters shall be reset by the driver/firmware once
377 * disconnected. The attributes used with this command are defined in
378 * enum qca_wlan_vendor_attr_active_tos.
380 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the
381 * driver has detected an internal failure. This event carries the
382 * information indicating the reason that triggered this detection. The
383 * attributes for this command are defined in
384 * enum qca_wlan_vendor_attr_hang.
386 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values
387 * of spectral parameters used. The spectral scan parameters are specified
388 * by enum qca_wlan_vendor_attr_spectral_scan.
390 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats
391 * for spectral scan functionality. The debug stats are specified by
392 * enum qca_wlan_vendor_attr_spectral_diag_stats.
394 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral
395 * scan system capabilities. The capabilities are specified
396 * by enum qca_wlan_vendor_attr_spectral_cap.
398 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current
399 * status of spectral scan. The status values are specified
400 * by enum qca_wlan_vendor_attr_spectral_scan_status.
402 * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush
403 * peer pending packets. Specify the peer MAC address in
404 * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets
405 * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed
406 * in enum qca_wlan_vendor_attr_flush_pending.
408 * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative
409 * RF Operating Parameter (RROP) information. The attributes for this
410 * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is
411 * intended for use by external Auto Channel Selection applications.
413 * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate
414 * (SAR) power limits. This is a companion to the command
415 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the
416 * settings currently in use. The attributes returned by this command are
417 * defined by enum qca_vendor_attr_sar_limits.
419 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of
420 * the WLAN hardware MAC. Also, provides the WLAN netdev interface
421 * information attached to the respective MAC.
422 * This works both as a query (user space asks the current mode) or event
423 * interface (driver advertising the current mode to the user space).
424 * Driver does not trigger this event for temporary hardware mode changes.
425 * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion,
426 * channel change, etc.) are updated with this event. Attributes for this
427 * interface are defined in enum qca_wlan_vendor_attr_mac.
429 * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold
430 * per peer per TID. Attributes for this command are define in
431 * enum qca_wlan_set_qdepth_thresh_attr.
432 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action
433 * guide for WLAN driver. Request to suspend of driver and FW if the
434 * temperature is higher than the suspend threshold; resume action is
435 * requested to driver if the temperature is lower than the resume
436 * threshold. In user poll mode, request temperature data by user. For test
437 * purpose, getting thermal shutdown configuration parameters is needed.
438 * Attributes for this interface are defined in
439 * enum qca_wlan_vendor_attr_thermal_cmd.
440 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from
441 * driver. Thermal temperature and indication of resume completion are
442 * reported as thermal events. The attributes for this command are defined
443 * in enum qca_wlan_vendor_attr_thermal_event.
445 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi
446 * test configuration. Attributes for this command are defined in
447 * enum qca_wlan_vendor_attr_wifi_test_config.
449 * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an
450 * RX filter to receive frames from stations that are active on the
451 * operating channel, but not associated with the local device (e.g., STAs
452 * associated with other APs). Filtering is done based on a list of BSSIDs
453 * and STA MAC addresses added by the user. This command is also used to
454 * fetch the statistics of unassociated stations. The attributes used with
455 * this command are defined in enum qca_wlan_vendor_attr_bss_filter.
457 enum qca_nl80211_vendor_subcmds
{
458 QCA_NL80211_VENDOR_SUBCMD_UNSPEC
= 0,
459 QCA_NL80211_VENDOR_SUBCMD_TEST
= 1,
460 /* subcmds 2..8 not yet allocated */
461 QCA_NL80211_VENDOR_SUBCMD_ROAMING
= 9,
462 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY
= 10,
463 QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY
= 11,
464 QCA_NL80211_VENDOR_SUBCMD_NAN
= 12,
465 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT
= 13,
466 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET
= 14,
467 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET
= 15,
468 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR
= 16,
469 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS
= 17,
470 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS
= 18,
471 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS
= 19,
472 QCA_NL80211_VENDOR_SUBCMD_GSCAN_START
= 20,
473 QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP
= 21,
474 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS
= 22,
475 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES
= 23,
476 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS
= 24,
477 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE
= 25,
478 QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT
= 26,
479 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT
= 27,
480 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND
= 28,
481 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST
= 29,
482 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST
= 30,
483 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE
= 31,
484 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE
= 32,
485 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE
= 33,
486 QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE
= 34,
487 QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE
= 35,
488 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS
= 36,
489 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE
= 37,
490 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES
= 38,
491 QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI
= 39,
492 QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG
= 40,
493 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST
= 41,
494 QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX
= 42,
495 /* 43..49 - reserved for QCA */
496 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY
= 50,
497 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH
= 51,
498 QCA_NL80211_VENDOR_SUBCMD_APFIND
= 52,
499 /* 53 - reserved - was used by QCA, but not in use anymore */
500 QCA_NL80211_VENDOR_SUBCMD_DO_ACS
= 54,
501 QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES
= 55,
502 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED
= 56,
503 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED
= 57,
504 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED
= 58,
505 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED
= 59,
506 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED
= 60,
507 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO
= 61,
508 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START
= 62,
509 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP
= 63,
510 QCA_NL80211_VENDOR_SUBCMD_ROAM
= 64,
511 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST
= 65,
512 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST
= 66,
513 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND
= 67,
514 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST
= 68,
515 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST
= 69,
516 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST
= 70,
517 QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST
= 71,
518 QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND
= 72,
519 QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND
= 73,
520 /* Wi-Fi configuration subcommands */
521 QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION
= 74,
522 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION
= 75,
523 QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET
= 76,
524 QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA
= 77,
525 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES
= 78,
526 QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS
= 79,
527 QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI
= 80,
528 QCA_NL80211_VENDOR_SUBCMD_NDP
= 81,
529 QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD
= 82,
530 QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER
= 83,
531 QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE
= 84,
532 QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS
= 85,
533 /* 86-90 - reserved for QCA */
534 QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD
= 91,
535 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG
= 92,
536 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME
= 93,
537 QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT
= 94,
538 QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT
= 95,
539 QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER
= 96,
540 QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS
= 97,
541 QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS
= 98,
542 QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL
= 99,
543 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT
= 100,
544 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES
= 101,
545 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG
= 102,
546 QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST
= 103,
547 QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL
= 104,
548 QCA_NL80211_VENDOR_SUBCMD_SETBAND
= 105,
549 QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN
= 106,
550 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE
= 107,
551 QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
= 108,
552 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE
= 109,
553 /* 110..114 - reserved for QCA */
554 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB
= 115,
555 /* 116..117 - reserved for QCA */
556 QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG
= 118,
557 QCA_NL80211_VENDOR_SUBCMD_TSF
= 119,
558 QCA_NL80211_VENDOR_SUBCMD_WISA
= 120,
559 /* 121 - reserved for QCA */
560 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START
= 122,
561 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP
= 123,
562 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH
= 124,
563 QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND
= 125,
564 QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY
= 126,
565 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT
= 127,
566 /* FTM/indoor location subcommands */
567 QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA
= 128,
568 QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
= 129,
569 QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION
= 130,
570 QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
= 131,
571 QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE
= 132,
572 QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
= 133,
573 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
= 134,
574 QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS
= 135,
575 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
= 136,
576 QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST
= 137,
577 QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI
= 138,
578 /* DMG low level RF sector operations */
579 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG
= 139,
580 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
= 140,
581 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR
= 141,
582 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR
= 142,
583 QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS
= 143,
584 QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES
= 144,
585 QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN
= 145,
586 QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
= 146,
587 QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
= 147,
588 QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE
= 148,
589 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET
= 149,
590 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET
= 150,
591 QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS
= 151,
592 QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL
= 152,
593 QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT
= 153,
594 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
= 154,
595 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP
= 155,
596 QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS
= 156,
597 QCA_NL80211_VENDOR_SUBCMD_HANG
= 157,
598 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG
= 158,
599 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS
= 159,
600 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO
= 160,
601 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS
= 161,
602 /* Flush peer pending data */
603 QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING
= 162,
604 QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO
= 163,
605 QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS
= 164,
606 QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO
= 165,
607 QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
= 166,
608 /* Thermal shutdown commands to protect wifi chip */
609 QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD
= 167,
610 QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT
= 168,
611 /* Wi-Fi test configuration subcommand */
612 QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
= 169,
613 /* Frame filter operations for other BSSs/unassociated STAs */
614 QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER
= 170,
617 enum qca_wlan_vendor_attr
{
618 QCA_WLAN_VENDOR_ATTR_INVALID
= 0,
619 /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */
620 QCA_WLAN_VENDOR_ATTR_DFS
= 1,
621 /* used by QCA_NL80211_VENDOR_SUBCMD_NAN */
622 QCA_WLAN_VENDOR_ATTR_NAN
= 2,
623 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
624 QCA_WLAN_VENDOR_ATTR_STATS_EXT
= 3,
625 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */
626 QCA_WLAN_VENDOR_ATTR_IFINDEX
= 4,
627 /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined
628 * by enum qca_roaming_policy.
630 QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY
= 5,
631 QCA_WLAN_VENDOR_ATTR_MAC_ADDR
= 6,
632 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
633 QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS
= 7,
634 QCA_WLAN_VENDOR_ATTR_TEST
= 8,
635 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */
636 /* Unsigned 32-bit value. */
637 QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA
= 9,
638 /* Unsigned 32-bit value */
639 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND
= 10,
640 /* Unsigned 32-bit value */
641 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND
= 11,
642 /* Unsigned 32-bit value from enum qca_set_band. */
643 QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE
= 12,
644 /* Dummy (NOP) attribute for 64 bit padding */
645 QCA_WLAN_VENDOR_ATTR_PAD
= 13,
646 /* Unique FTM session cookie (Unsigned 64 bit). Specified in
647 * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in
648 * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and
649 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE.
651 QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE
= 14,
652 /* Indoor location capabilities, returned by
653 * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA.
654 * see enum qca_wlan_vendor_attr_loc_capa.
656 QCA_WLAN_VENDOR_ATTR_LOC_CAPA
= 15,
657 /* Array of nested attributes containing information about each peer
658 * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info
659 * for supported attributes for each peer.
661 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS
= 16,
662 /* Array of nested attributes containing measurement results for
663 * one or more peers, reported by the
664 * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event.
665 * See enum qca_wlan_vendor_attr_peer_result for list of supported
668 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS
= 17,
669 /* Flag attribute for enabling or disabling responder functionality. */
670 QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE
= 18,
671 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
672 * command to specify the LCI report that will be sent by
673 * the responder during a measurement exchange. The format is
674 * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10.
676 QCA_WLAN_VENDOR_ATTR_FTM_LCI
= 19,
677 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
678 * command to specify the location civic report that will
679 * be sent by the responder during a measurement exchange.
680 * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13.
682 QCA_WLAN_VENDOR_ATTR_FTM_LCR
= 20,
683 /* Session/measurement completion status code,
684 * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and
685 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
686 * see enum qca_vendor_attr_loc_session_status.
688 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS
= 21,
689 /* Initial dialog token used by responder (0 if not specified),
690 * unsigned 8 bit value.
692 QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN
= 22,
693 /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
694 * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if
695 * AOA measurements are needed as part of an FTM session.
696 * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See
697 * enum qca_wlan_vendor_attr_aoa_type.
699 QCA_WLAN_VENDOR_ATTR_AOA_TYPE
= 23,
700 /* A bit mask (unsigned 32 bit value) of antenna arrays used
701 * by indoor location measurements. Refers to the antenna
702 * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS.
704 QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK
= 24,
705 /* AOA measurement data. Its contents depends on the AOA measurement
706 * type and antenna array mask:
707 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values,
708 * phase of the strongest CIR path for each antenna in the measured
710 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16
711 * values, phase and amplitude of the strongest CIR path for each
712 * antenna in the measured array(s).
714 QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT
= 25,
715 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
716 * to specify the chain number (unsigned 32 bit value) to inquire
717 * the corresponding antenna RSSI value
719 QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX
= 26,
720 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
721 * to report the specific antenna RSSI value (unsigned 32 bit value)
723 QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI
= 27,
724 /* Frequency in MHz, various uses. Unsigned 32 bit value */
725 QCA_WLAN_VENDOR_ATTR_FREQ
= 28,
726 /* TSF timer value, unsigned 64 bit value.
727 * May be returned by various commands.
729 QCA_WLAN_VENDOR_ATTR_TSF
= 29,
730 /* DMG RF sector index, unsigned 16 bit number. Valid values are
731 * 0..127 for sector indices or 65535 as special value used to
732 * unlock sector selection in
733 * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR.
735 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX
= 30,
736 /* DMG RF sector type, unsigned 8 bit value. One of the values
737 * in enum qca_wlan_vendor_attr_dmg_rf_sector_type.
739 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE
= 31,
740 /* Bitmask of DMG RF modules for which information is requested. Each
741 * bit corresponds to an RF module with the same index as the bit
742 * number. Unsigned 32 bit number but only low 8 bits can be set since
743 * all DMG chips currently have up to 8 RF modules.
745 QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK
= 32,
746 /* Array of nested attributes where each entry is DMG RF sector
747 * configuration for a single RF module.
748 * Attributes for each entry are taken from enum
749 * qca_wlan_vendor_attr_dmg_rf_sector_cfg.
750 * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
751 * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG.
753 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG
= 33,
754 /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command
755 * to report frame aggregation statistics to userspace.
757 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM
= 34,
758 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO
= 35,
759 /* Unsigned 8-bit value representing MBO transition reason code as
760 * provided by the AP used by subcommand
761 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is
762 * specified by the userspace in the request to the driver.
764 QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON
= 36,
765 /* Array of nested attributes, BSSID and status code, used by subcommand
766 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each
767 * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info.
768 * The userspace space specifies the list/array of candidate BSSIDs in
769 * the order of preference in the request. The driver specifies the
770 * status code, for each BSSID in the list, in the response. The
771 * acceptable candidates are listed in the order preferred by the
774 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO
= 37,
775 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
776 * See enum qca_wlan_vendor_attr_brp_ant_limit_mode.
778 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE
= 38,
779 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
780 * to define the number of antennas to use for BRP.
781 * different purpose in each ANT_LIMIT_MODE:
783 * EFFECTIVE - upper limit to number of antennas to be used
784 * FORCE - exact number of antennas to be used
785 * unsigned 8 bit value
787 QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT
= 39,
788 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
789 * to report the corresponding antenna index to the chain RSSI value
791 QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO
= 40,
794 QCA_WLAN_VENDOR_ATTR_AFTER_LAST
,
795 QCA_WLAN_VENDOR_ATTR_MAX
= QCA_WLAN_VENDOR_ATTR_AFTER_LAST
- 1,
798 enum qca_roaming_policy
{
799 QCA_ROAMING_NOT_ALLOWED
,
800 QCA_ROAMING_ALLOWED_WITHIN_ESS
,
803 enum qca_wlan_vendor_attr_roam_auth
{
804 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID
= 0,
805 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID
,
806 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE
,
807 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE
,
808 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED
,
809 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR
,
810 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK
,
811 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK
,
812 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS
,
813 /* Indicates the status of re-association requested by user space for
814 * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID.
816 * Represents the status code from AP. Use
817 * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the
818 * real status code for failures.
820 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS
,
821 /* This attribute indicates that the old association was maintained when
822 * a re-association is requested by user space and that re-association
823 * attempt fails (i.e., cannot connect to the requested BSS, but can
824 * remain associated with the BSS with which the association was in
825 * place when being requested to roam). Used along with
826 * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current
827 * re-association status. Type flag.
828 * This attribute is applicable only for re-association failure cases.
830 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION
,
831 /* This attribute specifies the PMK if one was newly generated during
832 * FILS roaming. This is added to the PMKSA cache and is used in
833 * subsequent connections with PMKSA caching.
835 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK
= 11,
836 /* This attribute specifies the PMKID used/generated for the current
837 * FILS roam. This is used in subsequent connections with PMKSA caching.
839 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID
= 12,
840 /* A 16-bit unsigned value specifying the next sequence number to use
841 * in ERP message in the currently associated realm. This is used in
842 * doing subsequent ERP based connections in the same realm.
844 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM
= 13,
846 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST
,
847 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX
=
848 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST
- 1
851 enum qca_wlan_vendor_attr_p2p_listen_offload
{
852 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID
= 0,
853 /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
854 * of the social channels.
856 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL
,
857 /* A 32-bit unsigned value; the P2P listen offload period (ms).
859 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD
,
860 /* A 32-bit unsigned value; the P2P listen interval duration (ms).
862 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL
,
863 /* A 32-bit unsigned value; number of interval times the firmware needs
864 * to run the offloaded P2P listen operation before it stops.
866 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT
,
867 /* An array of arbitrary binary data with one or more 8-byte values.
868 * The device types include both primary and secondary device types.
870 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES
,
871 /* An array of unsigned 8-bit characters; vendor information elements.
873 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE
,
874 /* A 32-bit unsigned value; a control flag to indicate whether listen
875 * results need to be flushed to wpa_supplicant.
877 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG
,
878 /* A 8-bit unsigned value; reason code for P2P listen offload stop
881 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON
,
883 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST
,
884 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX
=
885 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST
- 1
888 enum qca_wlan_vendor_attr_acs_offload
{
889 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID
= 0,
890 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL
,
891 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL
,
892 QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE
,
893 QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED
,
894 QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED
,
895 QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED
,
896 QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH
,
897 QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST
,
898 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL
,
899 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL
,
900 QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST
,
902 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST
,
903 QCA_WLAN_VENDOR_ATTR_ACS_MAX
=
904 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST
- 1
907 enum qca_wlan_vendor_acs_hw_mode
{
908 QCA_ACS_MODE_IEEE80211B
,
909 QCA_ACS_MODE_IEEE80211G
,
910 QCA_ACS_MODE_IEEE80211A
,
911 QCA_ACS_MODE_IEEE80211AD
,
912 QCA_ACS_MODE_IEEE80211ANY
,
916 * enum qca_wlan_vendor_features - Vendor device/driver feature flags
918 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key
919 * management offload, a mechanism where the station's firmware
920 * does the exchange with the AP to establish the temporal keys
921 * after roaming, rather than having the user space wpa_supplicant do it.
922 * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic
923 * band selection based on channel selection results.
924 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
925 * simultaneous off-channel operations.
926 * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
927 * Listen offload; a mechanism where the station's firmware takes care of
928 * responding to incoming Probe Request frames received from other P2P
929 * Devices whilst in Listen state, rather than having the user space
930 * wpa_supplicant do it. Information from received P2P requests are
931 * forwarded from firmware to host whenever the host processor wakes up.
932 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA
934 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific
936 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON
937 * specific features only. If a Device sets this bit but not the
938 * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that
939 * this Device may not support all OCE AP functionalities but can support
940 * only OCE STA-CFON functionalities.
941 * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self
942 * managed regulatory.
943 * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
945 enum qca_wlan_vendor_features
{
946 QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD
= 0,
947 QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY
= 1,
948 QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS
= 2,
949 QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD
= 3,
950 QCA_WLAN_VENDOR_FEATURE_OCE_STA
= 4,
951 QCA_WLAN_VENDOR_FEATURE_OCE_AP
= 5,
952 QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON
= 6,
953 QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY
= 7,
954 NUM_QCA_WLAN_VENDOR_FEATURES
/* keep last */
958 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication
960 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to
961 * the offloaded data.
962 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded
964 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload
967 enum qca_wlan_vendor_attr_data_offload_ind
{
968 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID
= 0,
969 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION
,
970 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL
,
971 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT
,
974 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST
,
975 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX
=
976 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST
- 1
980 * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set
983 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the
985 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule
986 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels
987 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be
989 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel
991 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL
992 * active state configuration
993 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as
994 * OCB_CONFIG_FLAG_80211_FRAME_MODE
995 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to
996 * use in the case that a packet is sent without a TX control header
997 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the
998 * last TA received that the local time set by TA is synchronous to other
999 * communicating OCB STAs.
1001 enum qca_wlan_vendor_attr_ocb_set_config
{
1002 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID
= 0,
1003 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT
= 1,
1004 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE
= 2,
1005 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY
= 3,
1006 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY
= 4,
1007 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY
= 5,
1008 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY
= 6,
1009 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS
= 7,
1010 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM
= 8,
1011 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION
= 9,
1012 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST
,
1013 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX
=
1014 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST
- 1
1018 * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set
1021 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of
1023 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of
1026 enum qca_wlan_vendor_attr_ocb_set_utc_time
{
1027 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID
= 0,
1028 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE
= 1,
1029 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR
= 2,
1030 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST
,
1031 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX
=
1032 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST
- 1
1036 * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes
1037 * to start sending timing advert frames
1039 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency
1040 * on which to send the frames
1041 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times
1042 * the frame is sent in 5 seconds
1044 enum qca_wlan_vendor_attr_ocb_start_timing_advert
{
1045 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID
= 0,
1046 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ
= 1,
1047 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE
= 2,
1048 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST
,
1049 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX
=
1050 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST
- 1
1054 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes
1055 * to stop timing advert
1057 * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel
1058 * frequency on which to stop the timing advert
1060 enum qca_wlan_vendor_attr_ocb_stop_timing_advert
{
1061 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID
= 0,
1062 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ
= 1,
1063 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST
,
1064 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX
=
1065 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST
- 1
1069 * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to
1070 * get TSF timer value
1072 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the
1074 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer
1076 enum qca_wlan_vendor_attr_ocb_get_tsf_resp
{
1077 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID
= 0,
1078 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH
= 1,
1079 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW
= 2,
1080 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST
,
1081 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX
=
1082 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST
- 1
1085 enum qca_vendor_attr_get_preferred_freq_list
{
1086 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID
,
1087 /* A 32-unsigned value; the interface type/mode for which the preferred
1088 * frequency list is requested (see enum qca_iface_type for possible
1089 * values); used in GET_PREFERRED_FREQ_LIST command from user-space to
1090 * kernel and in the kernel response back to user-space.
1092 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE
,
1093 /* An array of 32-unsigned values; values are frequency (MHz); sent
1094 * from kernel space to user space.
1096 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST
,
1097 /* An array of nested values as per enum qca_wlan_vendor_attr_pcl
1098 * attribute. Each element contains frequency (MHz), weight, and flag
1099 * bit mask indicating how the frequency should be used in P2P
1100 * negotiation; sent from kernel space to user space.
1102 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL
,
1104 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST
,
1105 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX
=
1106 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST
- 1
1109 enum qca_vendor_attr_probable_oper_channel
{
1110 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID
,
1111 /* 32-bit unsigned value; indicates the connection/iface type likely to
1112 * come on this channel (see enum qca_iface_type).
1114 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE
,
1115 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */
1116 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ
,
1118 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST
,
1119 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX
=
1120 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST
- 1
1123 enum qca_iface_type
{
1126 QCA_IFACE_TYPE_P2P_CLIENT
,
1127 QCA_IFACE_TYPE_P2P_GO
,
1128 QCA_IFACE_TYPE_IBSS
,
1129 QCA_IFACE_TYPE_TDLS
,
1139 * enum qca_access_policy - Access control policy
1141 * Access control policy is applied on the configured IE
1142 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
1143 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
1145 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
1146 * the specific configuration (IE) set, i.e., allow all the
1147 * connections which do not match the configuration.
1148 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
1149 * the specific configuration (IE) set, i.e., deny all the
1150 * connections which do not match the configuration.
1152 enum qca_access_policy
{
1153 QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED
,
1154 QCA_ACCESS_POLICY_DENY_UNLESS_LISTED
,
1158 * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
1159 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
1160 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
1161 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized
1162 * SOC timer value at TSF capture
1164 enum qca_vendor_attr_tsf_cmd
{
1165 QCA_WLAN_VENDOR_ATTR_TSF_INVALID
= 0,
1166 QCA_WLAN_VENDOR_ATTR_TSF_CMD
,
1167 QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE
,
1168 QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE
,
1169 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST
,
1170 QCA_WLAN_VENDOR_ATTR_TSF_MAX
=
1171 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST
- 1
1175 * enum qca_tsf_operation: TSF driver commands
1176 * @QCA_TSF_CAPTURE: Initiate TSF Capture
1177 * @QCA_TSF_GET: Get TSF capture value
1178 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value
1187 * enum qca_vendor_attr_wisa_cmd
1188 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32)
1189 * WISA setup vendor commands
1191 enum qca_vendor_attr_wisa_cmd
{
1192 QCA_WLAN_VENDOR_ATTR_WISA_INVALID
= 0,
1193 QCA_WLAN_VENDOR_ATTR_WISA_MODE
,
1194 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST
,
1195 QCA_WLAN_VENDOR_ATTR_WISA_MAX
=
1196 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST
- 1
1199 /* IEEE 802.11 Vendor Specific elements */
1202 * enum qca_vendor_element_id - QCA Vendor Specific element types
1204 * These values are used to identify QCA Vendor Specific elements. The
1205 * payload of the element starts with the three octet OUI (OUI_QCA) and
1206 * is followed by a single octet type which is defined by this enum.
1208 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list.
1209 * This element can be used to specify preference order for supported
1210 * channels. The channels in this list are in preference order (the first
1211 * one has the highest preference) and are described as a pair of
1212 * (global) Operating Class and Channel Number (each one octet) fields.
1214 * This extends the standard P2P functionality by providing option to have
1215 * more than one preferred operating channel. When this element is present,
1216 * it replaces the preference indicated in the Operating Channel attribute.
1217 * For supporting other implementations, the Operating Channel attribute is
1218 * expected to be used with the highest preference channel. Similarly, all
1219 * the channels included in this Preferred channel list element are
1220 * expected to be included in the Channel List attribute.
1222 * This vendor element may be included in GO Negotiation Request, P2P
1223 * Invitation Request, and Provision Discovery Request frames.
1225 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
1226 * This element can be used for pre-standard publication testing of HE
1227 * before P802.11ax draft assigns the element ID. The payload of this
1228 * vendor specific element is defined by the latest P802.11ax draft.
1229 * Please note that the draft is still work in progress and this element
1230 * payload is subject to change.
1232 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
1233 * This element can be used for pre-standard publication testing of HE
1234 * before P802.11ax draft assigns the element ID. The payload of this
1235 * vendor specific element is defined by the latest P802.11ax draft.
1236 * Please note that the draft is still work in progress and this element
1237 * payload is subject to change.
1239 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set
1241 * This element can be used for pre-standard publication testing of HE
1242 * before P802.11ax draft assigns the element ID extension. The payload of
1243 * this vendor specific element is defined by the latest P802.11ax draft
1244 * (not including the Element ID Extension field). Please note that the
1245 * draft is still work in progress and this element payload is subject to
1248 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element.
1249 * This element can be used for pre-standard publication testing of HE
1250 * before P802.11ax draft assigns the element ID extension. The payload of
1251 * this vendor specific element is defined by the latest P802.11ax draft
1252 * (not including the Element ID Extension field). Please note that the
1253 * draft is still work in progress and this element payload is subject to
1256 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element.
1257 * This element can be used for pre-standard publication testing of HE
1258 * before P802.11ax draft assigns the element ID extension. The payload of
1259 * this vendor specific element is defined by the latest P802.11ax draft
1260 * (not including the Element ID Extension field). Please note that the
1261 * draft is still work in progress and this element payload is subject to
1264 enum qca_vendor_element_id
{
1265 QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST
= 0,
1266 QCA_VENDOR_ELEM_HE_CAPAB
= 1,
1267 QCA_VENDOR_ELEM_HE_OPER
= 2,
1268 QCA_VENDOR_ELEM_RAPS
= 3,
1269 QCA_VENDOR_ELEM_MU_EDCA_PARAMS
= 4,
1270 QCA_VENDOR_ELEM_BSS_COLOR_CHANGE
= 5,
1274 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes
1276 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan
1277 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes
1278 * with frequencies to be scanned (in MHz)
1279 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned
1280 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported
1281 * rates to be included
1282 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests
1283 * at non CCK rate in 2GHz band
1284 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags
1285 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the
1286 * driver for the specific scan request
1287 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan
1288 * request decoded as in enum scan_status
1289 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation
1291 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
1293 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
1294 * specific BSSID to scan for.
1296 enum qca_wlan_vendor_attr_scan
{
1297 QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM
= 0,
1298 QCA_WLAN_VENDOR_ATTR_SCAN_IE
= 1,
1299 QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES
= 2,
1300 QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS
= 3,
1301 QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES
= 4,
1302 QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE
= 5,
1303 QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS
= 6,
1304 QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE
= 7,
1305 QCA_WLAN_VENDOR_ATTR_SCAN_STATUS
= 8,
1306 QCA_WLAN_VENDOR_ATTR_SCAN_MAC
= 9,
1307 QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK
= 10,
1308 QCA_WLAN_VENDOR_ATTR_SCAN_BSSID
= 11,
1309 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST
,
1310 QCA_WLAN_VENDOR_ATTR_SCAN_MAX
=
1311 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST
- 1
1315 * enum scan_status - Specifies the valid values the vendor scan attribute
1316 * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take
1318 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with
1320 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between
1323 VENDOR_SCAN_STATUS_NEW_RESULTS
,
1324 VENDOR_SCAN_STATUS_ABORTED
,
1325 VENDOR_SCAN_STATUS_MAX
,
1329 * enum qca_vendor_attr_ota_test - Specifies the values for vendor
1330 * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
1331 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test
1333 enum qca_vendor_attr_ota_test
{
1334 QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID
,
1335 /* 8-bit unsigned value to indicate if OTA test is enabled */
1336 QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE
,
1338 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST
,
1339 QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX
=
1340 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST
- 1
1344 * enum qca_vendor_attr_txpower_scale - vendor sub commands index
1346 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value
1348 enum qca_vendor_attr_txpower_scale
{
1349 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID
,
1350 /* 8-bit unsigned value to indicate the scaling of tx power */
1351 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE
,
1353 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST
,
1354 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX
=
1355 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST
- 1
1359 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease
1361 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB.
1363 enum qca_vendor_attr_txpower_decr_db
{
1364 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID
,
1365 /* 8-bit unsigned value to indicate the reduction of TX power in dB for
1366 * a virtual interface.
1368 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB
,
1370 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST
,
1371 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX
=
1372 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST
- 1
1375 /* Attributes for data used by
1376 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
1377 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
1379 enum qca_wlan_vendor_attr_config
{
1380 QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID
= 0,
1381 /* Unsigned 32-bit value to set the DTIM period.
1382 * Whether the wifi chipset wakes at every dtim beacon or a multiple of
1383 * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
1386 QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM
= 1,
1387 /* Unsigned 32-bit value to set the wifi_iface stats averaging factor
1388 * used to calculate statistics like average the TSF offset or average
1389 * number of frame leaked.
1390 * For instance, upon Beacon frame reception:
1391 * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
1392 * For instance, when evaluating leaky APs:
1393 * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
1395 QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR
= 2,
1396 /* Unsigned 32-bit value to configure guard time, i.e., when
1397 * implementing IEEE power management based on frame control PM bit, how
1398 * long the driver waits before shutting down the radio and after
1399 * receiving an ACK frame for a Data frame with PM bit set.
1401 QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME
= 3,
1402 /* Unsigned 32-bit value to change the FTM capability dynamically */
1403 QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT
= 4,
1404 /* Unsigned 16-bit value to configure maximum TX rate dynamically */
1405 QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE
= 5,
1406 /* Unsigned 32-bit value to configure the number of continuous
1407 * Beacon Miss which shall be used by the firmware to penalize
1410 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS
= 6,
1411 /* Unsigned 8-bit value to configure the channel avoidance indication
1412 * behavior. Firmware to send only one indication and ignore duplicate
1413 * indications when set to avoid multiple Apps wakeups.
1415 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND
= 7,
1416 /* 8-bit unsigned value to configure the maximum TX MPDU for
1419 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION
= 8,
1420 /* 8-bit unsigned value to configure the maximum RX MPDU for
1423 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION
= 9,
1424 /* 8-bit unsigned value to configure the Non aggregrate/11g sw
1425 * retry threshold (0 disable, 31 max).
1427 QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY
= 10,
1428 /* 8-bit unsigned value to configure the aggregrate sw
1429 * retry threshold (0 disable, 31 max).
1431 QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY
= 11,
1432 /* 8-bit unsigned value to configure the MGMT frame
1433 * retry threshold (0 disable, 31 max).
1435 QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY
= 12,
1436 /* 8-bit unsigned value to configure the CTRL frame
1437 * retry threshold (0 disable, 31 max).
1439 QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY
= 13,
1440 /* 8-bit unsigned value to configure the propagation delay for
1441 * 2G/5G band (0~63, units in us)
1443 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY
= 14,
1444 /* Unsigned 32-bit value to configure the number of unicast TX fail
1445 * packet count. The peer is disconnected once this threshold is
1448 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT
= 15,
1449 /* Attribute used to set scan default IEs to the driver.
1451 * These IEs can be used by scan operations that will be initiated by
1452 * the driver/firmware.
1454 * For further scan requests coming to the driver, these IEs should be
1455 * merged with the IEs received along with scan request coming to the
1456 * driver. If a particular IE is present in the scan default IEs but not
1457 * present in the scan request, then that IE should be added to the IEs
1458 * sent in the Probe Request frames for that scan request.
1460 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES
= 16,
1461 /* Unsigned 32-bit attribute for generic commands */
1462 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND
= 17,
1463 /* Unsigned 32-bit value attribute for generic commands */
1464 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE
= 18,
1465 /* Unsigned 32-bit data attribute for generic command response */
1466 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
= 19,
1467 /* Unsigned 32-bit length attribute for
1468 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
1470 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH
= 20,
1471 /* Unsigned 32-bit flags attribute for
1472 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA
1474 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS
= 21,
1475 /* Unsigned 32-bit, defining the access policy.
1476 * See enum qca_access_policy. Used with
1477 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST.
1479 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY
= 22,
1480 /* Sets the list of full set of IEs for which a specific access policy
1481 * has to be applied. Used along with
1482 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
1483 * Zero length payload can be used to clear this access constraint.
1485 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST
= 23,
1486 /* Unsigned 32-bit, specifies the interface index (netdev) for which the
1487 * corresponding configurations are applied. If the interface index is
1488 * not specified, the configurations are attributed to the respective
1491 QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX
= 24,
1492 /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
1493 QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER
= 25,
1494 /* 8-bit unsigned value to configure the driver and below layers to
1495 * ignore the assoc disallowed set by APs while connecting
1496 * 1-Ignore, 0-Don't ignore
1498 QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED
= 26,
1499 /* 32-bit unsigned value to trigger antenna diversity features:
1500 * 1-Enable, 0-Disable
1502 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA
= 27,
1503 /* 32-bit unsigned value to configure specific chain antenna */
1504 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN
= 28,
1505 /* 32-bit unsigned value to trigger cycle selftest
1506 * 1-Enable, 0-Disable
1508 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST
= 29,
1509 /* 32-bit unsigned to configure the cycle time of selftest
1510 * the unit is micro-second
1512 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL
= 30,
1513 /* 32-bit unsigned value to set reorder timeout for AC_VO */
1514 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE
= 31,
1515 /* 32-bit unsigned value to set reorder timeout for AC_VI */
1516 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO
= 32,
1517 /* 32-bit unsigned value to set reorder timeout for AC_BE */
1518 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT
= 33,
1519 /* 32-bit unsigned value to set reorder timeout for AC_BK */
1520 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND
= 34,
1521 /* 6-byte MAC address to point out the specific peer */
1522 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC
= 35,
1523 /* 32-bit unsigned value to set window size for specific peer */
1524 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT
= 36,
1525 /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */
1526 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24
= 37,
1527 /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */
1528 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5
= 38,
1529 /* 32-bit unsigned value to configure 5 or 10 MHz channel width for
1530 * station device while in disconnect state. The attribute use the
1531 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz,
1532 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or
1533 * 10 MHz channel width, the station will not connect to a BSS using 20
1534 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to
1535 * clear this constraint.
1537 QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH
= 39,
1538 /* 32-bit unsigned value to configure the propagation absolute delay
1539 * for 2G/5G band (units in us)
1541 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY
= 40,
1542 /* 32-bit unsigned value to set probe period */
1543 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD
= 41,
1544 /* 32-bit unsigned value to set stay period */
1545 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD
= 42,
1546 /* 32-bit unsigned value to set snr diff */
1547 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF
= 43,
1548 /* 32-bit unsigned value to set probe dwell time */
1549 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME
= 44,
1550 /* 32-bit unsigned value to set mgmt snr weight */
1551 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT
= 45,
1552 /* 32-bit unsigned value to set data snr weight */
1553 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT
= 46,
1554 /* 32-bit unsigned value to set ack snr weight */
1555 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT
= 47,
1556 /* 32-bit unsigned value to configure the listen interval.
1557 * This is in units of beacon intervals. This configuration alters
1558 * the negotiated listen interval with the AP during the connection.
1559 * It is highly recommended to configure a value less than or equal to
1560 * the one negotiated during the association. Configuring any greater
1561 * value can have adverse effects (frame loss, AP disassociating STA,
1564 QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL
= 48,
1566 * 8 bit unsigned value that is set on an AP/GO virtual interface to
1567 * disable operations that would cause the AP/GO to leave its operating
1570 * This will restrict the scans to the AP/GO operating channel and the
1571 * channels of the other band, if DBS is supported.A STA/CLI interface
1572 * brought up after this setting is enabled, will be restricted to
1573 * connecting to devices only on the AP/GO interface's operating channel
1574 * or on the other band in DBS case. P2P supported channel list is
1575 * modified, to only include AP interface's operating-channel and the
1576 * channels of the other band if DBS is supported.
1578 * These restrictions are only applicable as long as the AP/GO interface
1579 * is alive. If the AP/GO interface is brought down then this
1580 * setting/restriction is forgotten.
1582 * If this variable is set on an AP/GO interface while a multi-channel
1583 * concurrent session is active, it has no effect on the operation of
1584 * the current interfaces, other than restricting the scan to the AP/GO
1585 * operating channel and the other band channels if DBS is supported.
1586 * However, if the STA is brought down and restarted then the new STA
1587 * connection will either be formed on the AP/GO channel or on the
1588 * other band in a DBS case. This is because of the scan being
1589 * restricted on these channels as mentioned above.
1591 * 1-Restrict / 0-Don't restrict offchannel operations.
1593 QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL
= 49,
1595 * 8 bit unsigned value to enable/disable LRO (Large Receive Offload)
1597 * 1 - Enable, 0 - Disable.
1599 QCA_WLAN_VENDOR_ATTR_CONFIG_LRO
= 50,
1602 * 8 bit unsigned value to globally enable/disable scan
1603 * 1 - Enable, 0 - Disable.
1605 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE
= 51,
1607 /* 8-bit unsigned value to set the total beacon miss count
1608 * This parameter will set the total beacon miss count.
1610 QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT
= 52,
1612 /* Unsigned 32-bit value to configure the number of continuous
1613 * Beacon Miss which shall be used by the firmware to penalize
1616 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC
= 53,
1618 /* 8-bit unsigned value to configure the driver and below layers to
1619 * enable/disable all FILS features.
1620 * 0-enable, 1-disable
1622 QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS
= 54,
1624 /* 16-bit unsigned value to configure the level of WLAN latency
1625 * module. See enum qca_wlan_vendor_attr_config_latency_level.
1627 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL
= 55,
1629 /* 8-bit unsigned value indicating the driver to use the RSNE as-is from
1630 * the connect interface. Exclusively used for the scenarios where the
1631 * device is used as a test bed device with special functionality and
1632 * not recommended for production. This helps driver to not validate the
1633 * RSNE passed from user space and thus allow arbitrary IE data to be
1634 * used for testing purposes.
1635 * 1-enable, 0-disable.
1636 * Applications set/reset this configuration. If not reset, this
1637 * parameter remains in use until the driver is unloaded.
1639 QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE
= 56,
1641 /* 8-bit unsigned value to trigger green Tx power saving.
1642 * 1-Enable, 0-Disable
1644 QCA_WLAN_VENDOR_ATTR_CONFIG_GTX
= 57,
1647 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST
,
1648 QCA_WLAN_VENDOR_ATTR_CONFIG_MAX
=
1649 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST
- 1,
1653 * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
1655 enum qca_wlan_vendor_attr_sap_config
{
1656 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID
= 0,
1657 /* 1 - reserved for QCA */
1658 /* List of frequencies on which AP is expected to operate.
1659 * This is irrespective of ACS configuration. This list is a priority
1660 * based one and is looked for before the AP is created to ensure the
1661 * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
1664 QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST
= 2,
1666 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST
,
1667 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX
=
1668 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST
- 1,
1672 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
1673 * conditional channel switch
1675 enum qca_wlan_vendor_attr_sap_conditional_chan_switch
{
1676 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID
= 0,
1677 /* Priority based frequency list (an array of u32 values in host byte
1680 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST
= 1,
1681 /* Status of the conditional switch (u32).
1682 * 0: Success, Non-zero: Failure
1684 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS
= 2,
1686 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST
,
1687 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX
=
1688 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST
- 1,
1692 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
1694 enum qca_wlan_gpio_attr
{
1695 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID
= 0,
1696 /* Unsigned 32-bit attribute for GPIO command */
1697 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND
,
1698 /* Unsigned 32-bit attribute for GPIO PIN number to configure */
1699 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM
,
1700 /* Unsigned 32-bit attribute for GPIO value to configure */
1701 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE
,
1702 /* Unsigned 32-bit attribute for GPIO pull type */
1703 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE
,
1704 /* Unsigned 32-bit attribute for GPIO interrupt mode */
1705 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE
,
1708 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST
,
1709 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX
=
1710 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST
- 1
1714 * qca_wlan_set_qdepth_thresh_attr - Parameters for setting
1715 * MSDUQ depth threshold per peer per tid in the target
1717 * Associated Vendor Command:
1718 * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
1720 enum qca_wlan_set_qdepth_thresh_attr
{
1721 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID
= 0,
1722 /* 6-byte MAC address */
1723 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR
,
1724 /* Unsigned 32-bit attribute for holding the TID */
1725 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID
,
1726 /* Unsigned 32-bit attribute for holding the update mask
1727 * bit 0 - Update high priority msdu qdepth threshold
1728 * bit 1 - Update low priority msdu qdepth threshold
1729 * bit 2 - Update UDP msdu qdepth threshold
1730 * bit 3 - Update Non UDP msdu qdepth threshold
1731 * rest of bits are reserved
1733 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK
,
1734 /* Unsigned 32-bit attribute for holding the threshold value */
1735 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE
,
1738 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST
,
1739 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX
=
1740 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST
- 1,
1744 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
1746 enum qca_wlan_vendor_attr_get_hw_capability
{
1747 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID
,
1748 /* Antenna isolation
1749 * An attribute used in the response.
1750 * The content of this attribute is encoded in a byte array. Each byte
1751 * value is an antenna isolation value. The array length is the number
1754 QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION
,
1755 /* Request HW capability
1756 * An attribute used in the request.
1757 * The content of this attribute is a u32 array for one or more of
1758 * hardware capabilities (attribute IDs) that are being requested. Each
1759 * u32 value has a value from this
1760 * enum qca_wlan_vendor_attr_get_hw_capability
1761 * identifying which capabilities are requested.
1763 QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY
,
1766 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST
,
1767 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX
=
1768 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST
- 1,
1772 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
1773 * offload which is an extension for LL_STATS.
1774 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
1775 * If MAC counters do not exceed the threshold, FW will report monitored
1776 * link layer counters periodically as this setting. The first report is
1777 * always triggered by this timer.
1778 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
1779 * For each MAC layer counter, FW holds two copies. One is the current value.
1780 * The other is the last report. Once a current counter's increment is larger
1781 * than the threshold, FW will indicate that counter to host even if the
1782 * monitoring timer does not expire.
1783 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
1784 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
1785 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
1787 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
1788 * 1: TX packet discarded
1791 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address
1792 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state
1793 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold.
1794 * Threshold for all monitored parameters. If per counter dedicated threshold
1795 * is not enabled, this threshold will take effect.
1796 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this
1797 * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0.
1798 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID
1799 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID
1800 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters
1801 * Bit0: TX counter unit in MSDU
1802 * Bit1: TX counter unit in MPDU
1803 * Bit2: TX counter unit in PPDU
1804 * Bit3: TX counter unit in byte
1805 * Bit4: Dropped MSDUs
1806 * Bit5: Dropped Bytes
1807 * Bit6: MPDU retry counter
1808 * Bit7: MPDU failure counter
1809 * Bit8: PPDU failure counter
1810 * Bit9: MPDU aggregation counter
1811 * Bit10: MCS counter for ACKed MPDUs
1812 * Bit11: MCS counter for Failed MPDUs
1813 * Bit12: TX Delay counter
1814 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters
1815 * Bit0: MAC RX counter unit in MPDU
1816 * Bit1: MAC RX counter unit in byte
1817 * Bit2: PHY RX counter unit in PPDU
1818 * Bit3: PHY RX counter unit in byte
1819 * Bit4: Disorder counter
1820 * Bit5: Retry counter
1821 * Bit6: Duplication counter
1822 * Bit7: Discard counter
1823 * Bit8: MPDU aggregation size counter
1825 * Bit10: Peer STA power state change (wake to sleep) counter
1826 * Bit11: Peer STA power save counter, total time in PS mode
1827 * Bit12: Probe request counter
1828 * Bit13: Other management frames counter
1829 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA
1832 * Bit2: time RX in current bss
1833 * Bit3: Out of current bss time
1834 * Bit4: Wireless medium busy time
1835 * Bit5: RX in bad condition time
1836 * Bit6: TX in bad condition time
1837 * Bit7: time wlan card not available
1838 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal
1839 * Bit0: Per channel SNR counter
1840 * Bit1: Per channel noise floor counter
1841 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers
1842 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels
1843 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats
1844 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats
1845 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats
1846 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs
1847 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs
1848 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs
1849 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data
1850 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets
1851 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped
1852 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK
1853 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed
1854 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed
1855 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM:
1856 * aggregation stats buffer length
1857 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats
1858 * buffer for ACKed MPDUs.
1859 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats
1860 * buffer for failed MPDUs.
1861 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE:
1862 * length of delay stats array.
1863 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats
1864 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs
1865 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs
1866 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats
1867 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received
1868 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received
1869 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received
1870 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received
1871 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost
1872 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets
1873 * flagged as retransmissions
1874 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets
1875 * flagged as duplicated
1876 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX
1878 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation
1880 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs
1882 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer
1883 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer
1884 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep
1885 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time
1886 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe
1888 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt
1890 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time
1891 * there is no TX, nor RX, nor interference.
1892 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time
1893 * transmitting packets.
1894 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time
1896 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time
1897 * interference detected.
1898 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time
1899 * receiving packets with errors.
1900 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time
1902 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time
1903 * the chip is unable to work in normal conditions.
1904 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time
1905 * receiving packets in current BSS.
1906 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time
1907 * receiving packets not in current BSS.
1908 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas
1909 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL:
1910 * This is a container for per antenna signal stats.
1911 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value
1912 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value
1913 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon
1914 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon
1915 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64
1916 * Absolute timestamp from 1970/1/1, unit in ms. After receiving the
1917 * message, user layer APP could call gettimeofday to get another
1918 * timestamp and calculate transfer delay for the message.
1919 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32
1920 * Real period for this measurement, unit in us.
1922 enum qca_wlan_vendor_attr_ll_stats_ext
{
1923 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID
= 0,
1925 /* Attributes for configurations */
1926 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD
,
1927 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD
,
1929 /* Peer STA power state change */
1930 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG
,
1932 /* TX failure event */
1933 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID
,
1934 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU
,
1935 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS
,
1937 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE
,
1938 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS
,
1941 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL
,
1942 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE
,
1943 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID
,
1944 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID
,
1945 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP
,
1946 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP
,
1947 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP
,
1948 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP
,
1949 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM
,
1950 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM
,
1951 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS
,
1952 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER
,
1954 /* Sub-attributes for PEER_AC_TX */
1955 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU
,
1956 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU
,
1957 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU
,
1958 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES
,
1959 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP
,
1960 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES
,
1961 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY
,
1962 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK
,
1963 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK
,
1964 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM
,
1965 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM
,
1966 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM
,
1967 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR
,
1968 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS
,
1969 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS
,
1970 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE
,
1971 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY
,
1973 /* Sub-attributes for PEER_AC_RX */
1974 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU
,
1975 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES
,
1976 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU
,
1977 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES
,
1978 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST
,
1979 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY
,
1980 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP
,
1981 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD
,
1982 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM
,
1983 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM
,
1984 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS
,
1985 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR
,
1986 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES
,
1987 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION
,
1988 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ
,
1989 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT
,
1991 /* Sub-attributes for CCA_BSS */
1992 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME
,
1993 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME
,
1994 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME
,
1995 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY
,
1996 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD
,
1997 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD
,
1998 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL
,
2000 /* sub-attribute for BSS_RX_TIME */
2001 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME
,
2002 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME
,
2004 /* Sub-attributes for PEER_SIGNAL */
2005 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM
,
2006 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL
,
2007 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR
,
2008 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF
,
2010 /* Sub-attributes for IFACE_BSS */
2011 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON
,
2012 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON
,
2014 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME
,
2015 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME
,
2017 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST
,
2018 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX
=
2019 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST
- 1
2022 /* Attributes for FTM commands and events */
2025 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities
2027 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See
2028 * enum qca_wlan_vendor_attr_loc_capa_flags.
2029 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number
2030 * of measurement sessions that can run concurrently.
2031 * Default is one session (no session concurrency).
2032 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique
2033 * peers that are supported in running sessions. For example,
2034 * if the value is 8 and maximum number of sessions is 2, you can
2035 * have one session with 8 unique peers, or 2 sessions with 4 unique
2036 * peers each, and so on.
2037 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number
2038 * of bursts per peer, as an exponent (2^value). Default is 0,
2039 * meaning no multi-burst support.
2040 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number
2041 * of measurement exchanges allowed in a single burst.
2042 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement
2043 * types. A bit mask (unsigned 32 bit value), each bit corresponds
2044 * to an AOA type as defined by enum qca_vendor_attr_aoa_type.
2046 enum qca_wlan_vendor_attr_loc_capa
{
2047 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID
,
2048 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS
,
2049 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS
,
2050 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS
,
2051 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP
,
2052 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST
,
2053 QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES
,
2055 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST
,
2056 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX
=
2057 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST
- 1,
2061 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags
2063 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver
2064 * can be configured as an FTM responder (for example, an AP that
2065 * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
2066 * will be supported if set.
2067 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver
2068 * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
2069 * will be supported if set.
2070 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder
2071 * supports immediate (ASAP) response.
2072 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone
2073 * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS.
2074 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports
2075 * requesting AOA measurements as part of an FTM session.
2077 enum qca_wlan_vendor_attr_loc_capa_flags
{
2078 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER
= 1 << 0,
2079 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR
= 1 << 1,
2080 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP
= 1 << 2,
2081 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA
= 1 << 3,
2082 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM
= 1 << 4,
2086 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about
2087 * a single peer in a measurement session.
2089 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer.
2090 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related
2091 * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags.
2092 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of
2093 * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0
2094 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for
2095 * list of supported attributes.
2096 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for
2097 * secure measurement.
2098 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA
2099 * measurement every <value> bursts. If 0 or not specified,
2100 * AOA measurements will be disabled for this peer.
2101 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where
2102 * the measurement frames are exchanged. Optional; if not
2103 * specified, try to locate the peer in the kernel scan
2104 * results cache and use frequency from there.
2106 enum qca_wlan_vendor_attr_ftm_peer_info
{
2107 QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID
,
2108 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR
,
2109 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS
,
2110 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS
,
2111 QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID
,
2112 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD
,
2113 QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ
,
2115 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST
,
2116 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX
=
2117 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST
- 1,
2121 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags,
2124 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request
2125 * immediate (ASAP) response from peer.
2126 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request
2127 * LCI report from peer. The LCI report includes the absolute
2128 * location of the peer in "official" coordinates (similar to GPS).
2129 * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information.
2130 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request
2131 * Location civic report from peer. The LCR includes the location
2132 * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0,
2133 * 11.24.6.7 for more information.
2134 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set,
2135 * request a secure measurement.
2136 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided.
2138 enum qca_wlan_vendor_attr_ftm_peer_meas_flags
{
2139 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP
= 1 << 0,
2140 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI
= 1 << 1,
2141 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR
= 1 << 2,
2142 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE
= 1 << 3,
2146 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters
2148 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements
2149 * to perform in a single burst.
2150 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to
2151 * perform, specified as an exponent (2^value).
2152 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst
2153 * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167.
2154 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts,
2155 * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must
2156 * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION.
2158 enum qca_wlan_vendor_attr_ftm_meas_param
{
2159 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID
,
2160 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST
,
2161 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP
,
2162 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION
,
2163 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD
,
2165 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST
,
2166 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX
=
2167 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST
- 1,
2171 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results
2173 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported
2175 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement
2176 * request for this peer.
2177 * See enum qca_wlan_vendor_attr_ftm_peer_result_status.
2178 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related
2179 * to measurement results for this peer.
2180 * See enum qca_wlan_vendor_attr_ftm_peer_result_flags.
2181 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when
2182 * request failed and peer requested not to send an additional request
2183 * for this number of seconds.
2184 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received
2185 * from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
2187 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when
2188 * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
2190 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer
2191 * overridden some measurement request parameters. See
2192 * enum qca_wlan_vendor_attr_ftm_meas_param.
2193 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement
2194 * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
2195 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement
2196 * results. Each entry is a nested attribute defined
2197 * by enum qca_wlan_vendor_attr_ftm_meas.
2199 enum qca_wlan_vendor_attr_ftm_peer_result
{
2200 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID
,
2201 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR
,
2202 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS
,
2203 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS
,
2204 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
,
2205 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI
,
2206 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR
,
2207 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS
,
2208 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS
,
2209 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS
,
2211 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST
,
2212 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX
=
2213 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST
- 1,
2217 * enum qca_wlan_vendor_attr_ftm_peer_result_status
2219 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results
2220 * will be provided. Peer may have overridden some measurement parameters,
2221 * in which case overridden parameters will be report by
2222 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute.
2223 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable
2224 * of performing the measurement request. No more results will be sent
2225 * for this peer in this session.
2226 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request
2227 * failed, and requested not to send an additional request for number
2228 * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
2230 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation
2231 * failed. Request was not sent over the air.
2233 enum qca_wlan_vendor_attr_ftm_peer_result_status
{
2234 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK
,
2235 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE
,
2236 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED
,
2237 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID
,
2241 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags
2242 * for measurement result, per-peer
2244 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set,
2245 * measurement completed for this peer. No more results will be reported
2246 * for this peer in this session.
2248 enum qca_wlan_vendor_attr_ftm_peer_result_flags
{
2249 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE
= 1 << 0,
2253 * enum qca_vendor_attr_loc_session_status: Session completion status code
2255 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed
2257 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted
2259 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request
2260 * was invalid and was not started.
2261 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error
2262 * and did not complete normally (for example out of resources).
2264 enum qca_vendor_attr_loc_session_status
{
2265 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK
,
2266 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED
,
2267 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID
,
2268 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED
,
2272 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data
2274 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as
2275 * recorded by responder, in picoseconds.
2276 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2277 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at
2278 * initiator, in picoseconds.
2279 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2280 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by
2281 * initiator, in picoseconds.
2282 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2283 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at
2284 * responder, in picoseconds.
2285 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
2286 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded
2287 * during this measurement exchange. Optional and will be provided if
2288 * the hardware can measure it.
2289 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by
2290 * responder. Not always provided.
2291 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2292 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by
2293 * responder. Not always provided.
2294 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2295 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by
2296 * initiator. Not always provided.
2297 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2298 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by
2299 * initiator. Not always provided.
2300 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
2301 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding.
2303 enum qca_wlan_vendor_attr_ftm_meas
{
2304 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID
,
2305 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1
,
2306 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2
,
2307 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3
,
2308 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4
,
2309 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI
,
2310 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR
,
2311 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR
,
2312 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR
,
2313 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR
,
2314 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD
,
2316 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST
,
2317 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX
=
2318 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST
- 1,
2322 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type
2324 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest
2325 * CIR (channel impulse response) path for each antenna.
2326 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude
2327 * of the strongest CIR path for each antenna.
2329 enum qca_wlan_vendor_attr_aoa_type
{
2330 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE
,
2331 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP
,
2332 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX
2336 * enum qca_wlan_vendor_attr_encryption_test - Attributes to
2337 * validate encryption engine
2339 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute.
2340 * This will be included if the request is for decryption; if not included,
2341 * the request is treated as a request for encryption by default.
2342 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value
2343 * indicating the key cipher suite. Takes same values as
2344 * NL80211_ATTR_KEY_CIPHER.
2345 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value
2346 * Key Id to be used for encryption
2347 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values.
2348 * Key (TK) to be used for encryption/decryption
2349 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values.
2350 * Packet number to be specified for encryption/decryption
2351 * 6 bytes for TKIP/CCMP/GCMP.
2352 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values
2353 * representing the 802.11 packet (header + payload + FCS) that
2354 * needs to be encrypted/decrypted.
2355 * Encrypted/decrypted response from the driver will also be sent
2356 * to userspace with the same attribute.
2358 enum qca_wlan_vendor_attr_encryption_test
{
2359 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID
= 0,
2360 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION
,
2361 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER
,
2362 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID
,
2363 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK
,
2364 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN
,
2365 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA
,
2368 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST
,
2369 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX
=
2370 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST
- 1
2374 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of
2375 * sector for DMG RF sector operations.
2377 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector
2378 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector
2380 enum qca_wlan_vendor_attr_dmg_rf_sector_type
{
2381 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX
,
2382 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX
,
2383 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX
2387 * BRP antenna limit mode
2389 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force
2390 * antenna limit, BRP will be performed as usual.
2391 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal
2392 * antennas limit. the hardware may use less antennas than the
2394 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will
2395 * use exactly the specified number of antennas for BRP.
2397 enum qca_wlan_vendor_attr_brp_ant_limit_mode
{
2398 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE
,
2399 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE
,
2400 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE
,
2401 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX
2405 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for
2406 * DMG RF sector configuration for a single RF module.
2407 * The values are defined in a compact way which closely matches
2408 * the way it is stored in HW registers.
2409 * The configuration provides values for 32 antennas and 8 distribution
2410 * amplifiers, and together describes the characteristics of the RF
2411 * sector - such as a beam in some direction with some gain.
2413 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index
2414 * of RF module for this configuration.
2415 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge
2416 * amplifier gain index. Unsigned 32 bit number containing
2417 * bits for all 32 antennas.
2418 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge
2419 * amplifier gain index. Unsigned 32 bit number containing
2420 * bits for all 32 antennas.
2421 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge
2422 * amplifier gain index. Unsigned 32 bit number containing
2423 * bits for all 32 antennas.
2424 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values
2425 * for first 16 antennas, 2 bits per antenna.
2426 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values
2427 * for last 16 antennas, 2 bits per antenna.
2428 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains
2429 * DTYPE values (3 bits) for each distribution amplifier, followed
2430 * by X16 switch bits for each distribution amplifier. There are
2431 * total of 8 distribution amplifiers.
2433 enum qca_wlan_vendor_attr_dmg_rf_sector_cfg
{
2434 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID
= 0,
2435 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX
= 1,
2436 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0
= 2,
2437 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1
= 3,
2438 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2
= 4,
2439 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI
= 5,
2440 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO
= 6,
2441 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16
= 7,
2444 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST
,
2445 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX
=
2446 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST
- 1
2449 enum qca_wlan_vendor_attr_ll_stats_set
{
2450 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID
= 0,
2451 /* Unsigned 32-bit value */
2452 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD
= 1,
2453 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING
= 2,
2455 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST
,
2456 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX
=
2457 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST
- 1,
2460 enum qca_wlan_vendor_attr_ll_stats_clr
{
2461 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID
= 0,
2462 /* Unsigned 32bit bitmap for clearing statistics
2463 * All radio statistics 0x00000001
2464 * cca_busy_time (within radio statistics) 0x00000002
2465 * All channel stats (within radio statistics) 0x00000004
2466 * All scan statistics (within radio statistics) 0x00000008
2467 * All interface statistics 0x00000010
2468 * All tx rate statistics (within interface statistics) 0x00000020
2469 * All ac statistics (with in interface statistics) 0x00000040
2470 * All contention (min, max, avg) statistics (within ac statisctics)
2473 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK
= 1,
2474 /* Unsigned 8 bit value: Request to stop statistics collection */
2475 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ
= 2,
2477 /* Unsigned 32 bit bitmap: Response from the driver
2478 * for the cleared statistics
2480 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK
= 3,
2481 /* Unsigned 8 bit value: Response from driver/firmware
2482 * for the stop request
2484 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP
= 4,
2486 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST
,
2487 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX
=
2488 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST
- 1,
2491 enum qca_wlan_vendor_attr_ll_stats_get
{
2492 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID
= 0,
2493 /* Unsigned 32 bit value provided by the caller issuing the GET stats
2494 * command. When reporting the stats results, the driver uses the same
2495 * value to indicate which GET request the results correspond to.
2497 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID
= 1,
2498 /* Unsigned 32 bit value - bit mask to identify what statistics are
2499 * requested for retrieval.
2500 * Radio Statistics 0x00000001
2501 * Interface Statistics 0x00000020
2502 * All Peer Statistics 0x00000040
2503 * Peer Statistics 0x00000080
2505 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK
= 2,
2507 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST
,
2508 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX
=
2509 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST
- 1,
2512 enum qca_wlan_vendor_attr_ll_stats_results
{
2513 QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID
= 0,
2514 /* Unsigned 32bit value. Used by the driver; must match the request id
2515 * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command.
2517 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID
= 1,
2519 /* Unsigned 32 bit value */
2520 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX
= 2,
2521 /* Unsigned 32 bit value */
2522 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX
= 3,
2523 /* Unsigned 32 bit value */
2524 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX
= 4,
2525 /* Unsigned 32 bit value */
2526 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX
= 5,
2527 /* Signed 32 bit value */
2528 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT
= 6,
2529 /* Signed 32 bit value */
2530 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA
= 7,
2531 /* Signed 32 bit value */
2532 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK
= 8,
2534 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are
2535 * nested within the interface stats.
2538 /* Interface mode, e.g., STA, SOFTAP, IBSS, etc.
2539 * Type = enum wifi_interface_mode.
2541 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE
= 9,
2542 /* Interface MAC address. An array of 6 Unsigned int8 */
2543 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR
= 10,
2544 /* Type = enum wifi_connection_state, e.g., DISCONNECTED,
2545 * AUTHENTICATING, etc. valid for STA, CLI only.
2547 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE
= 11,
2548 /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE
2550 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING
= 12,
2551 /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */
2552 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES
= 13,
2553 /* NULL terminated SSID. An array of 33 Unsigned 8bit values */
2554 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID
= 14,
2555 /* BSSID. An array of 6 unsigned 8 bit values */
2556 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID
= 15,
2557 /* Country string advertised by AP. An array of 3 unsigned 8 bit
2560 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR
= 16,
2561 /* Country string for this association. An array of 3 unsigned 8 bit
2564 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR
= 17,
2566 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could
2567 * be nested within the interface stats.
2570 /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */
2571 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC
= 18,
2572 /* Unsigned int 32 value corresponding to respective AC */
2573 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU
= 19,
2574 /* Unsigned int 32 value corresponding to respective AC */
2575 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU
= 20,
2576 /* Unsigned int 32 value corresponding to respective AC */
2577 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST
= 21,
2578 /* Unsigned int 32 value corresponding to respective AC */
2579 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST
= 22,
2580 /* Unsigned int 32 value corresponding to respective AC */
2581 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU
= 23,
2582 /* Unsigned int 32 value corresponding to respective AC */
2583 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU
= 24,
2584 /* Unsigned int 32 value corresponding to respective AC */
2585 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST
= 25,
2586 /* Unsigned int 32 value corresponding to respective AC */
2587 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES
= 26,
2588 /* Unsigned int 32 value corresponding to respective AC */
2589 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT
= 27,
2590 /* Unsigned int 32 values corresponding to respective AC */
2591 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG
= 28,
2592 /* Unsigned int 32 values corresponding to respective AC */
2593 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN
= 29,
2594 /* Unsigned int 32 values corresponding to respective AC */
2595 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX
= 30,
2596 /* Unsigned int 32 values corresponding to respective AC */
2597 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG
= 31,
2598 /* Unsigned int 32 values corresponding to respective AC */
2599 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES
= 32,
2600 /* Unsigned 32 bit value. Number of peers */
2601 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS
= 33,
2603 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are
2604 * nested within the interface stats.
2607 /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */
2608 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE
= 34,
2609 /* MAC addr corresponding to respective peer. An array of 6 unsigned
2612 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS
= 35,
2613 /* Unsigned int 32 bit value representing capabilities corresponding
2614 * to respective peer.
2616 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES
= 36,
2617 /* Unsigned 32 bit value. Number of rates */
2618 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES
= 37,
2620 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
2621 * are nested within the rate stat.
2624 /* Wi-Fi Rate - separate attributes defined for individual fields */
2626 /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */
2627 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE
= 38,
2628 /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */
2629 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS
= 39,
2630 /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */
2631 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW
= 40,
2632 /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std
2633 * in the units of 0.5 Mbps HT/VHT it would be MCS index
2635 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX
= 41,
2637 /* Unsigned 32 bit value. Bit rate in units of 100 kbps */
2638 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE
= 42,
2640 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be
2641 * nested within the peer info stats.
2644 /* Unsigned int 32 bit value. Number of successfully transmitted data
2645 * packets, i.e., with ACK received corresponding to the respective
2648 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU
= 43,
2649 /* Unsigned int 32 bit value. Number of received data packets
2650 * corresponding to the respective rate.
2652 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU
= 44,
2653 /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK
2654 * received corresponding to the respective rate.
2656 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST
= 45,
2657 /* Unsigned int 32 bit value. Total number of data packet retries for
2658 * the respective rate.
2660 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES
= 46,
2661 /* Unsigned int 32 bit value. Total number of short data packet retries
2662 * for the respective rate.
2664 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT
= 47,
2665 /* Unsigned int 32 bit value. Total number of long data packet retries
2666 * for the respective rate.
2668 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG
= 48,
2670 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID
= 49,
2671 /* Unsigned 32 bit value. Total number of msecs the radio is awake
2672 * accruing over time.
2674 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME
= 50,
2675 /* Unsigned 32 bit value. Total number of msecs the radio is
2676 * transmitting accruing over time.
2678 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME
= 51,
2679 /* Unsigned 32 bit value. Total number of msecs the radio is in active
2680 * receive accruing over time.
2682 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME
= 52,
2683 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2684 * to all scan accruing over time.
2686 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN
= 53,
2687 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2688 * to NAN accruing over time.
2690 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD
= 54,
2691 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2692 * to GSCAN accruing over time.
2694 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN
= 55,
2695 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2696 * to roam scan accruing over time.
2698 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN
= 56,
2699 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2700 * to PNO scan accruing over time.
2702 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN
= 57,
2703 /* Unsigned 32 bit value. Total number of msecs the radio is awake due
2704 * to Hotspot 2.0 scans and GAS exchange accruing over time.
2706 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20
= 58,
2707 /* Unsigned 32 bit value. Number of channels. */
2708 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS
= 59,
2710 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could
2711 * be nested within the channel stats.
2714 /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */
2715 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH
= 60,
2716 /* Unsigned 32 bit value. Primary 20 MHz channel. */
2717 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ
= 61,
2718 /* Unsigned 32 bit value. Center frequency (MHz) first segment. */
2719 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0
= 62,
2720 /* Unsigned 32 bit value. Center frequency (MHz) second segment. */
2721 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1
= 63,
2723 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be
2724 * nested within the radio stats.
2727 /* Unsigned int 32 bit value representing total number of msecs the
2728 * radio is awake on that channel accruing over time, corresponding to
2729 * the respective channel.
2731 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME
= 64,
2732 /* Unsigned int 32 bit value representing total number of msecs the CCA
2733 * register is busy accruing over time corresponding to the respective
2736 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME
= 65,
2738 QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS
= 66,
2740 /* Signifies the nested list of channel attributes
2741 * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_*
2743 QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO
= 67,
2745 /* Signifies the nested list of peer info attributes
2746 * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*
2748 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO
= 68,
2750 /* Signifies the nested list of rate info attributes
2751 * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
2753 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO
= 69,
2755 /* Signifies the nested list of wmm info attributes
2756 * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_*
2758 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO
= 70,
2760 /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates
2761 * that more stats, e.g., peers or radio, are to follow in the next
2762 * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event.
2763 * Otherwise, it is set to 0.
2765 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA
= 71,
2767 /* Unsigned 64 bit value */
2768 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET
= 72,
2770 /* Unsigned 32 bit value */
2771 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED
= 73,
2773 /* Unsigned 32 bit value */
2774 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED
= 74,
2776 /* Unsigned 32 bit value */
2777 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME
= 75,
2779 /* Unsigned 32 bit value */
2780 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE
= 76,
2782 /* Unsigned 32 bit value */
2783 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS
= 77,
2785 /* Number of msecs the radio spent in transmitting for each power level
2787 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL
= 78,
2789 /* Unsigned 32 bit value */
2790 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT
= 79,
2791 /* Unsigned 32 bit value */
2792 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT
= 80,
2793 /* Unsigned 32 bit value */
2794 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT
= 81,
2795 /* Unsigned 32 bit value */
2796 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT
= 82,
2798 /* Unsigned int 32 value.
2799 * Pending MSDUs corresponding to respective AC.
2801 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU
= 83,
2804 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST
,
2805 QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX
=
2806 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST
- 1,
2809 enum qca_wlan_vendor_attr_ll_stats_type
{
2810 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID
= 0,
2811 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO
= 1,
2812 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE
= 2,
2813 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS
= 3,
2816 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST
,
2817 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX
=
2818 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST
- 1,
2822 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for
2823 * TDLS configuration to the host driver.
2825 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger
2826 * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode
2827 * represents the different TDLS trigger modes.
2828 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within
2829 * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number
2830 * of packets shall meet the criteria for implicit TDLS setup.
2831 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets
2832 * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
2833 * to initiate a TDLS setup.
2834 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate
2835 * a TDLS Discovery to the peer.
2836 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of
2837 * discovery attempts to know the TDLS capability of the peer. A peer is
2838 * marked as TDLS not capable if there is no response for all the attempts.
2839 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32)
2840 * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
2841 * number of TX / RX frames meet the criteria for TDLS teardown.
2842 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32)
2843 * of Tx/Rx packets within a duration
2844 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link.
2845 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold
2846 * corresponding to the RSSI of the peer below which a TDLS setup is
2848 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold
2849 * corresponding to the RSSI of the peer above which a TDLS teardown is
2852 enum qca_wlan_vendor_attr_tdls_configuration
{
2853 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID
= 0,
2854 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE
= 1,
2856 /* Attributes configuring the TDLS Implicit Trigger */
2857 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
= 2,
2858 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD
= 3,
2859 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD
= 4,
2860 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT
= 5,
2861 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT
= 6,
2862 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
= 7,
2863 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD
= 8,
2864 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD
= 9,
2867 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST
,
2868 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX
=
2869 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST
- 1
2873 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in
2876 * The following are the different values for
2877 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE.
2879 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown
2880 * the TDLS connection to a respective peer comes from the user space.
2881 * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN,
2882 * TDLS_DISCOVER to do this.
2883 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS
2884 * setup/teardown to the eligible peer once the configured criteria
2885 * (such as TX/RX threshold, RSSI) is met. The attributes
2886 * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to
2887 * the different configuration criteria for the TDLS trigger from the
2889 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger
2890 * the TDLS setup / teardown through the implicit mode only to the
2891 * configured MAC addresses (wpa_supplicant, with tdls_external_control=1,
2892 * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands).
2893 * External mode works on top of the implicit mode. Thus the host driver
2894 * is expected to configure in TDLS Implicit mode too to operate in
2896 * Configuring External mode alone without Implicit mode is invalid.
2898 * All the above implementations work as expected only when the host driver
2899 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing
2900 * that the TDLS message exchange is not internal to the host driver, but
2901 * depends on wpa_supplicant to do the message exchange.
2903 enum qca_wlan_vendor_tdls_trigger_mode
{
2904 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT
= 1 << 0,
2905 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT
= 1 << 1,
2906 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL
= 1 << 2,
2910 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
2911 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
2912 * that is hard-coded in the Board Data File (BDF).
2913 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
2914 * that is hard-coded in the Board Data File (BDF).
2915 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
2916 * that is hard-coded in the Board Data File (BDF).
2917 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
2918 * that is hard-coded in the Board Data File (BDF).
2919 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
2920 * that is hard-coded in the Board Data File (BDF).
2921 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
2922 * source of SAR power limits, thereby disabling the SAR power
2924 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
2925 * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
2926 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power
2927 * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
2929 * This enumerates the valid set of values that may be supplied for
2930 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
2931 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in
2932 * the response to an instance of the
2933 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
2935 enum qca_vendor_attr_sar_limits_selections
{
2936 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0
= 0,
2937 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1
= 1,
2938 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2
= 2,
2939 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3
= 3,
2940 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4
= 4,
2941 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE
= 5,
2942 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER
= 6,
2943 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0
= 7,
2947 * enum qca_vendor_attr_sar_limits_spec_modulations -
2948 * SAR limits specification modulation
2949 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
2951 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
2954 * This enumerates the valid set of values that may be supplied for
2955 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
2956 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
2957 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
2958 * command or in the response to an instance of the
2959 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
2961 enum qca_vendor_attr_sar_limits_spec_modulations
{
2962 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK
= 0,
2963 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM
= 1,
2967 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
2969 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to
2970 * select which SAR power limit table should be used. Valid
2971 * values are enumerated in enum
2972 * %qca_vendor_attr_sar_limits_selections. The existing SAR
2973 * power limit selection is unchanged if this attribute is not
2976 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
2977 * which specifies the number of SAR power limit specifications
2978 * which will follow.
2980 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
2981 * limit specifications. The number of specifications is
2982 * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
2983 * specification contains a set of
2984 * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
2985 * specification is uniquely identified by the attributes
2986 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
2987 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
2988 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
2989 * contains as a payload the attribute
2990 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT,
2991 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX.
2992 * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or
2993 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is
2994 * needed based upon the value of
2995 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE.
2997 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
2998 * indicate for which band this specification applies. Valid
2999 * values are enumerated in enum %nl80211_band (although not all
3000 * bands may be supported by a given device). If the attribute is
3001 * not supplied then the specification will be applied to all
3004 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
3005 * to indicate for which antenna chain this specification
3006 * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
3007 * attribute is not supplied then the specification will be
3008 * applied to all chains.
3010 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
3011 * value to indicate for which modulation scheme this
3012 * specification applies. Valid values are enumerated in enum
3013 * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
3014 * is not supplied then the specification will be applied to all
3015 * modulation schemes.
3017 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
3018 * value to specify the actual power limit value in units of 0.5
3019 * dBm (i.e., a value of 11 represents 5.5 dBm).
3020 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
3021 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER.
3023 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32)
3024 * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles.
3025 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is
3026 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0.
3028 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
3029 * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS.
3031 enum qca_vendor_attr_sar_limits
{
3032 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID
= 0,
3033 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE
= 1,
3034 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS
= 2,
3035 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC
= 3,
3036 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND
= 4,
3037 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN
= 5,
3038 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION
= 6,
3039 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT
= 7,
3040 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX
= 8,
3042 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST
,
3043 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX
=
3044 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST
- 1
3048 * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
3049 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
3051 enum qca_wlan_vendor_attr_get_wifi_info
{
3052 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID
= 0,
3053 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION
= 1,
3054 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION
= 2,
3057 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST
,
3058 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX
=
3059 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST
- 1,
3063 * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by
3064 * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command.
3066 enum qca_wlan_vendor_attr_wifi_logger_start
{
3067 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID
= 0,
3068 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID
= 1,
3069 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL
= 2,
3070 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS
= 3,
3073 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST
,
3074 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX
=
3075 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST
- 1,
3078 enum qca_wlan_vendor_attr_logger_results
{
3079 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID
= 0,
3081 /* Unsigned 32-bit value; must match the request Id supplied by
3082 * Wi-Fi HAL in the corresponding subcmd NL msg.
3084 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID
= 1,
3086 /* Unsigned 32-bit value; used to indicate the size of memory
3087 * dump to be allocated.
3089 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE
= 2,
3092 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST
,
3093 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX
=
3094 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST
- 1,
3097 enum qca_wlan_vendor_attr_roaming_config_params
{
3098 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID
= 0,
3100 QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD
= 1,
3101 QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID
= 2,
3103 /* Attributes for wifi_set_ssid_white_list */
3104 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS
= 3,
3105 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST
= 4,
3106 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID
= 5,
3108 /* Attributes for set_roam_params */
3109 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD
= 6,
3110 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD
= 7,
3111 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR
= 8,
3112 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR
= 9,
3113 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST
= 10,
3114 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS
= 11,
3115 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER
= 12,
3117 /* Attribute for set_lazy_roam */
3118 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE
= 13,
3120 /* Attribute for set_lazy_roam with preferences */
3121 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS
= 14,
3122 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID
= 15,
3123 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID
= 16,
3124 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER
= 17,
3126 /* Attribute for set_blacklist bssid params */
3127 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS
= 18,
3128 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID
= 19,
3129 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID
= 20,
3132 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST
,
3133 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX
=
3134 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST
- 1,
3138 * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
3139 * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
3141 enum qca_wlan_vendor_attr_roam_subcmd
{
3142 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID
= 0,
3143 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST
= 1,
3144 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS
= 2,
3145 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM
= 3,
3146 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS
= 4,
3147 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS
= 5,
3148 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID
= 6,
3151 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST
,
3152 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX
=
3153 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST
- 1,
3156 enum qca_wlan_vendor_attr_gscan_config_params
{
3157 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID
= 0,
3159 /* Unsigned 32-bit value */
3160 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID
= 1,
3162 /* Attributes for data used by
3163 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command.
3165 /* Unsigned 32-bit value */
3166 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND
3168 /* Unsigned 32-bit value */
3169 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS
3172 /* Attributes for input params used by
3173 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command.
3176 /* Unsigned 32-bit value; channel frequency */
3177 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL
= 4,
3178 /* Unsigned 32-bit value; dwell time in ms. */
3179 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME
= 5,
3180 /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */
3181 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE
= 6,
3182 /* Unsigned 8-bit value; channel class */
3183 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS
= 7,
3185 /* Unsigned 8-bit value; bucket index, 0 based */
3186 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX
= 8,
3187 /* Unsigned 8-bit value; band. */
3188 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND
= 9,
3189 /* Unsigned 32-bit value; desired period, in ms. */
3190 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD
= 10,
3191 /* Unsigned 8-bit value; report events semantics. */
3192 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS
= 11,
3193 /* Unsigned 32-bit value. Followed by a nested array of
3194 * GSCAN_CHANNEL_SPEC_* attributes.
3196 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
= 12,
3198 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes.
3199 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
3201 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC
= 13,
3203 /* Unsigned 32-bit value; base timer period in ms. */
3204 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD
= 14,
3205 /* Unsigned 32-bit value; number of APs to store in each scan in the
3206 * BSSID/RSSI history buffer (keep the highest RSSI APs).
3208 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN
= 15,
3209 /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake
3212 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT
3215 /* Unsigned 8-bit value; number of scan bucket specs; followed by a
3216 * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size
3217 * of the array is determined by NUM_BUCKETS.
3219 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
= 17,
3221 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes.
3222 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
3224 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC
= 18,
3226 /* Unsigned 8-bit value */
3227 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH
3229 /* Unsigned 32-bit value; maximum number of results to be returned. */
3230 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX
3233 /* An array of 6 x unsigned 8-bit value */
3234 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID
= 21,
3235 /* Signed 32-bit value */
3236 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW
= 22,
3237 /* Signed 32-bit value */
3238 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH
= 23,
3239 /* Unsigned 32-bit value */
3240 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL
= 24,
3242 /* Number of hotlist APs as unsigned 32-bit value, followed by a nested
3243 * array of AP_THRESHOLD_PARAM attributes and values. The size of the
3244 * array is determined by NUM_AP.
3246 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP
= 25,
3248 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes.
3249 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
3251 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM
= 26,
3253 /* Unsigned 32-bit value; number of samples for averaging RSSI. */
3254 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE
3256 /* Unsigned 32-bit value; number of samples to confirm AP loss. */
3257 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE
3259 /* Unsigned 32-bit value; number of APs breaching threshold. */
3260 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING
= 29,
3261 /* Unsigned 32-bit value; number of APs. Followed by an array of
3262 * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP.
3264 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP
= 30,
3265 /* Unsigned 32-bit value; number of samples to confirm AP loss. */
3266 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE
3268 /* Unsigned 32-bit value. If max_period is non zero or different than
3269 * period, then this bucket is an exponential backoff bucket.
3271 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD
= 32,
3272 /* Unsigned 32-bit value. */
3273 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE
= 33,
3274 /* Unsigned 32-bit value. For exponential back off bucket, number of
3275 * scans to perform for a given period.
3277 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT
= 34,
3278 /* Unsigned 8-bit value; in number of scans, wake up AP after these
3281 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS
3284 /* Attributes for data used by
3285 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command.
3287 /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */
3288 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE
3290 /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a
3291 * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The
3292 * size of the array is determined by NUM_SSID.
3294 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
= 37,
3295 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_*
3297 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
3299 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM
= 38,
3301 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
3302 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID
= 39,
3303 /* Unsigned 8-bit value */
3304 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND
= 40,
3305 /* Signed 32-bit value */
3306 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW
= 41,
3307 /* Signed 32-bit value */
3308 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH
= 42,
3309 /* Unsigned 32-bit value; a bitmask with additional gscan config flag.
3311 QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS
= 43,
3314 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST
,
3315 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX
=
3316 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST
- 1,
3319 enum qca_wlan_vendor_attr_gscan_results
{
3320 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID
= 0,
3322 /* Unsigned 32-bit value; must match the request Id supplied by
3323 * Wi-Fi HAL in the corresponding subcmd NL msg.
3325 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID
= 1,
3327 /* Unsigned 32-bit value; used to indicate the status response from
3328 * firmware/driver for the vendor sub-command.
3330 QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS
= 2,
3332 /* GSCAN Valid Channels attributes */
3333 /* Unsigned 32bit value; followed by a nested array of CHANNELS. */
3334 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS
= 3,
3335 /* An array of NUM_CHANNELS x unsigned 32-bit value integers
3336 * representing channel numbers.
3338 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS
= 4,
3340 /* GSCAN Capabilities attributes */
3341 /* Unsigned 32-bit value */
3342 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE
= 5,
3343 /* Unsigned 32-bit value */
3344 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS
= 6,
3345 /* Unsigned 32-bit value */
3346 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN
3348 /* Unsigned 32-bit value */
3349 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE
3351 /* Signed 32-bit value */
3352 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD
3354 /* Unsigned 32-bit value */
3355 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS
= 10,
3356 /* Unsigned 32-bit value */
3357 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS
3359 /* Unsigned 32-bit value */
3360 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES
3363 /* GSCAN Attributes used with
3364 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command.
3367 /* Unsigned 32-bit value */
3368 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
= 13,
3370 /* GSCAN attributes used with
3371 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command.
3374 /* An array of NUM_RESULTS_AVAILABLE x
3375 * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_*
3377 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST
= 14,
3379 /* Unsigned 64-bit value; age of sample at the time of retrieval */
3380 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP
= 15,
3381 /* 33 x unsigned 8-bit value; NULL terminated SSID */
3382 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID
= 16,
3383 /* An array of 6 x unsigned 8-bit value */
3384 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID
= 17,
3385 /* Unsigned 32-bit value; channel frequency in MHz */
3386 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL
= 18,
3387 /* Signed 32-bit value */
3388 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI
= 19,
3389 /* Unsigned 32-bit value */
3390 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT
= 20,
3391 /* Unsigned 32-bit value */
3392 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD
= 21,
3393 /* Unsigned 16-bit value */
3394 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD
= 22,
3395 /* Unsigned 16-bit value */
3396 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY
= 23,
3397 /* Unsigned 32-bit value; size of the IE DATA blob */
3398 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH
= 24,
3399 /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the
3400 * information elements found in the beacon; this data should be a
3401 * packed list of wifi_information_element objects, one after the
3404 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA
= 25,
3406 /* Unsigned 8-bit value; set by driver to indicate more scan results are
3409 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA
= 26,
3411 /* GSCAN attributes for
3412 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command.
3414 /* Unsigned 8-bit value */
3415 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE
= 27,
3416 /* Unsigned 32-bit value */
3417 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS
= 28,
3419 /* GSCAN attributes for
3420 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command.
3422 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
3423 * to indicate number of results.
3424 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
3428 /* GSCAN attributes for
3429 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command.
3431 /* An array of 6 x unsigned 8-bit value */
3432 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID
= 29,
3433 /* Unsigned 32-bit value */
3434 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL
3436 /* Unsigned 32-bit value. */
3437 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI
3439 /* A nested array of signed 32-bit RSSI values. Size of the array is
3440 * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI.
3442 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST
3445 /* GSCAN attributes used with
3446 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command.
3448 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
3449 * to indicate number of gscan cached results returned.
3450 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate
3451 * the list of gscan cached results.
3454 /* An array of NUM_RESULTS_AVAILABLE x
3455 * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_*
3457 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST
= 33,
3458 /* Unsigned 32-bit value; a unique identifier for the scan unit. */
3459 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID
= 34,
3460 /* Unsigned 32-bit value; a bitmask w/additional information about scan.
3462 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS
= 35,
3463 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
3464 * to indicate number of wifi scan results/bssids retrieved by the scan.
3465 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
3466 * list of wifi scan results returned for each cached result block.
3469 /* GSCAN attributes for
3470 * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command.
3472 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for
3473 * number of results.
3474 * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
3475 * list of wifi scan results returned for each
3476 * wifi_passpoint_match_result block.
3477 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE.
3480 /* GSCAN attributes for
3481 * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command.
3483 /* Unsigned 32-bit value */
3484 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES
3486 /* A nested array of
3487 * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_*
3488 * attributes. Array size =
3489 * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES.
3491 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST
= 37,
3493 /* Unsigned 32-bit value; network block id for the matched network */
3494 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID
= 38,
3495 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
3496 * list of wifi scan results returned for each
3497 * wifi_passpoint_match_result block.
3499 /* Unsigned 32-bit value */
3500 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN
= 39,
3501 /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values;
3502 * ANQP data in the information_element format.
3504 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP
= 40,
3506 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3507 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS
= 41,
3508 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3509 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS
= 42,
3510 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3511 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID
3513 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
3514 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID
3517 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED
= 45,
3520 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST
,
3521 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX
=
3522 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST
- 1,
3525 enum qca_wlan_vendor_attr_pno_config_params
{
3526 QCA_WLAN_VENDOR_ATTR_PNO_INVALID
= 0,
3527 /* Attributes for data used by
3528 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command.
3530 /* Unsigned 32-bit value */
3531 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM
= 1,
3532 /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_*
3533 * attributes. Array size =
3534 * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM.
3536 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY
= 2,
3538 /* Unsigned 32-bit value */
3539 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID
= 3,
3540 /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded
3541 * realm, 0 if unspecified.
3543 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM
= 4,
3544 /* An array of 16 x unsigned 32-bit value; roaming consortium ids to
3545 * match, 0 if unspecified.
3547 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID
= 5,
3548 /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if
3551 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN
= 6,
3553 /* Attributes for data used by
3554 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command.
3556 /* Unsigned 32-bit value */
3557 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS
= 7,
3559 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_*
3560 * attributes. Array size =
3561 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS.
3563 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST
= 8,
3564 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
3565 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID
= 9,
3566 /* Signed 8-bit value; threshold for considering this SSID as found,
3567 * required granularity for this threshold is 4 dBm to 8 dBm.
3569 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD
3571 /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */
3572 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS
= 11,
3573 /* Unsigned 8-bit value; auth bit field for matching WPA IE */
3574 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT
= 12,
3575 /* Unsigned 8-bit to indicate ePNO type;
3576 * It takes values from qca_wlan_epno_type
3578 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE
= 13,
3580 /* Nested attribute to send the channel list */
3581 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST
= 14,
3583 /* Unsigned 32-bit value; indicates the interval between PNO scan
3586 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL
= 15,
3587 QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI
= 16,
3588 QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI
= 17,
3589 QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX
= 18,
3590 QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS
= 19,
3591 QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS
= 20,
3592 QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS
= 21,
3593 QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS
= 22,
3594 /* Unsigned 32-bit value, representing the PNO Request ID */
3595 QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID
= 23,
3598 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST
,
3599 QCA_WLAN_VENDOR_ATTR_PNO_MAX
=
3600 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST
- 1,
3604 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why
3605 * the ACS has to be triggered. These values are used by
3606 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and
3607 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
3609 enum qca_wlan_vendor_acs_select_reason
{
3610 /* Represents the reason that the ACS triggered during the AP start */
3611 QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT
,
3612 /* Represents the reason that DFS found with the current channel */
3613 QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS
,
3614 /* Represents the reason that LTE co-exist in the current band. */
3615 QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX
,
3619 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for
3620 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd
3621 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the
3622 * external ACS policies to select the channels w.r.t. the PCL weights.
3623 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and
3624 * their PCL weights.)
3625 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to
3626 * select a channel with non-zero PCL weight.
3627 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a
3628 * channel with non-zero PCL weight.
3631 enum qca_wlan_vendor_attr_external_acs_policy
{
3632 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED
,
3633 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY
,
3637 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel.
3638 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS.
3640 enum qca_wlan_vendor_channel_prop_flags
{
3641 /* Bits 0, 1, 2, and 3 are reserved */
3644 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO
= 1 << 4,
3646 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK
= 1 << 5,
3648 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM
= 1 << 6,
3649 /* 2.4 GHz spectrum channel. */
3650 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ
= 1 << 7,
3651 /* 5 GHz spectrum channel */
3652 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ
= 1 << 8,
3653 /* Only passive scan allowed */
3654 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE
= 1 << 9,
3655 /* Dynamic CCK-OFDM channel */
3656 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN
= 1 << 10,
3657 /* GFSK channel (FHSS PHY) */
3658 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK
= 1 << 11,
3659 /* Radar found on channel */
3660 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR
= 1 << 12,
3661 /* 11a static turbo channel only */
3662 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO
= 1 << 13,
3663 /* Half rate channel */
3664 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF
= 1 << 14,
3665 /* Quarter rate channel */
3666 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER
= 1 << 15,
3668 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20
= 1 << 16,
3669 /* HT 40 with extension channel above */
3670 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS
= 1 << 17,
3671 /* HT 40 with extension channel below */
3672 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS
= 1 << 18,
3673 /* HT 40 intolerant */
3674 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL
= 1 << 19,
3675 /* VHT 20 channel */
3676 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20
= 1 << 20,
3677 /* VHT 40 with extension channel above */
3678 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS
= 1 << 21,
3679 /* VHT 40 with extension channel below */
3680 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS
= 1 << 22,
3681 /* VHT 80 channel */
3682 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80
= 1 << 23,
3683 /* HT 40 intolerant mark bit for ACS use */
3684 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK
= 1 << 24,
3685 /* Channel temporarily blocked due to noise */
3686 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED
= 1 << 25,
3687 /* VHT 160 channel */
3688 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160
= 1 << 26,
3689 /* VHT 80+80 channel */
3690 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80
= 1 << 27,
3692 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20
= 1 << 28,
3693 /* HE 40 with extension channel above */
3694 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS
= 1 << 29,
3695 /* HE 40 with extension channel below */
3696 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS
= 1 << 30,
3697 /* HE 40 intolerant */
3698 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL
= 1 << 31,
3702 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a
3703 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is
3704 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2.
3706 enum qca_wlan_vendor_channel_prop_flags_2
{
3707 /* HE 40 intolerant mark bit for ACS use */
3708 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK
= 1 << 0,
3710 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80
= 1 << 1,
3711 /* HE 160 channel */
3712 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160
= 1 << 2,
3713 /* HE 80+80 channel */
3714 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80
= 1 << 3,
3718 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for
3719 * each channel. This is used by
3720 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT.
3722 enum qca_wlan_vendor_channel_prop_flags_ext
{
3723 /* Radar found on channel */
3724 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND
= 1 << 0,
3725 /* DFS required on channel */
3726 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS
= 1 << 1,
3727 /* DFS required on channel for 2nd band of 80+80 */
3728 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2
= 1 << 2,
3729 /* If channel has been checked for DFS */
3730 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR
= 1 << 3,
3731 /* Excluded in 802.11d */
3732 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED
= 1 << 4,
3733 /* Channel Switch Announcement received on this channel */
3734 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED
= 1 << 5,
3735 /* Ad-hoc is not allowed */
3736 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC
= 1 << 6,
3737 /* Station only channel */
3738 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP
= 1 << 7,
3739 /* DFS radar history for slave device (STA mode) */
3740 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR
= 1 << 8,
3741 /* DFS CAC valid for slave device (STA mode) */
3742 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID
= 1 << 9,
3746 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel
3747 * information. These attributes are sent as part of
3748 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following
3749 * attributes correspond to a single channel.
3751 enum qca_wlan_vendor_external_acs_event_chan_info_attr
{
3752 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID
= 0,
3754 /* A bitmask (u32) with flags specified in
3755 * enum qca_wlan_vendor_channel_prop_flags.
3757 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS
= 1,
3758 /* A bitmask (u32) with flags specified in
3759 * enum qca_wlan_vendor_channel_prop_flags_ext.
3761 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT
= 2,
3762 /* frequency in MHz (u32) */
3763 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ
= 3,
3764 /* maximum regulatory transmission power (u32) */
3765 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER
= 4,
3766 /* maximum transmission power (u32) */
3767 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER
= 5,
3768 /* minimum transmission power (u32) */
3769 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER
= 6,
3770 /* regulatory class id (u8) */
3771 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID
= 7,
3772 /* maximum antenna gain in (u8) */
3773 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN
= 8,
3774 /* VHT segment 0 (u8) */
3775 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0
= 9,
3776 /* VHT segment 1 (u8) */
3777 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1
= 10,
3778 /* A bitmask (u32) with flags specified in
3779 * enum qca_wlan_vendor_channel_prop_flags_2.
3781 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2
= 11,
3784 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST
,
3785 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX
=
3786 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST
- 1,
3790 * qca_wlan_vendor_attr_pcl: Represents attributes for
3791 * preferred channel list (PCL). These attributes are sent as part of
3792 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and
3793 * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST.
3795 enum qca_wlan_vendor_attr_pcl
{
3796 QCA_WLAN_VENDOR_ATTR_PCL_INVALID
= 0,
3798 /* Channel number (u8) */
3799 QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL
= 1,
3800 /* Channel weightage (u8) */
3801 QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT
= 2,
3802 /* Channel frequency (u32) in MHz */
3803 QCA_WLAN_VENDOR_ATTR_PCL_FREQ
= 3,
3804 /* Channel flags (u32)
3805 * bit 0 set: channel to be used for GO role,
3806 * bit 1 set: channel to be used on CLI role,
3807 * bit 2 set: channel must be considered for operating channel
3808 * selection & peer chosen operating channel should be
3809 * one of the channels with this flag set,
3810 * bit 3 set: channel should be excluded in GO negotiation
3812 QCA_WLAN_VENDOR_ATTR_PCL_FLAG
= 4,
3816 * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command
3817 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by
3820 enum qca_wlan_vendor_attr_external_acs_event
{
3821 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID
= 0,
3823 /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason.
3824 * This helps ACS module to understand why ACS needs to be started.
3826 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON
= 1,
3827 /* Flag attribute to indicate if driver supports spectral scanning */
3828 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED
= 2,
3829 /* Flag attribute to indicate if 11ac is offloaded to firmware */
3830 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED
= 3,
3831 /* Flag attribute to indicate if driver provides additional channel
3832 * capability as part of scan operation
3834 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT
= 4,
3835 /* Flag attribute to indicate interface status is UP */
3836 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP
= 5,
3837 /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype
3840 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE
= 6,
3841 /* Channel width (u8). It takes one of enum nl80211_chan_width values.
3842 * This is the upper bound of channel width. ACS logic should try to get
3843 * a channel with the specified width and if not found, look for lower
3846 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH
= 7,
3847 /* This (u8) will hold values of one of enum nl80211_bands */
3848 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND
= 8,
3849 /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode
3852 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE
= 9,
3853 /* Array of (u32) supported frequency list among which ACS should choose
3856 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST
= 10,
3857 /* Preferred channel list by the driver which will have array of nested
3858 * values as per enum qca_wlan_vendor_attr_pcl attribute.
3860 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL
= 11,
3861 /* Array of nested attribute for each channel. It takes attr as defined
3862 * in enum qca_wlan_vendor_external_acs_event_chan_info_attr.
3864 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO
= 12,
3865 /* External ACS policy such as PCL mandatory, PCL preferred, etc.
3866 * It uses values defined in enum
3867 * qca_wlan_vendor_attr_external_acs_policy.
3869 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY
= 13,
3870 /* Reference RF Operating Parameter (RROP) availability information
3871 * (u16). It uses values defined in enum
3872 * qca_wlan_vendor_attr_rropavail_info.
3874 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO
= 14,
3877 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST
,
3878 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX
=
3879 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST
- 1,
3883 * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
3884 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
3885 * in priority order as decided after ACS operation in userspace.
3887 enum qca_wlan_vendor_attr_external_acs_channels
{
3888 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID
= 0,
3890 /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason
3892 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
= 1,
3894 /* Array of nested values for each channel with following attributes:
3895 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND,
3896 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
3897 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
3898 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
3899 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
3900 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
3902 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST
= 2,
3903 /* This (u8) will hold values of one of enum nl80211_bands */
3904 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND
= 3,
3905 /* Primary channel (u8) */
3906 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY
= 4,
3907 /* Secondary channel (u8) used for HT 40 MHz channels */
3908 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY
= 5,
3909 /* VHT seg0 channel (u8) */
3910 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0
= 6,
3911 /* VHT seg1 channel (u8) */
3912 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1
= 7,
3913 /* Channel width (u8). Takes one of enum nl80211_chan_width values. */
3914 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
= 8,
3917 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST
,
3918 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX
=
3919 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST
- 1
3922 enum qca_chip_power_save_failure_reason
{
3923 /* Indicates if the reason for the failure is due to a protocol
3926 QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL
= 0,
3927 /* Indicates if the reason for the failure is due to a hardware issue.
3929 QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE
= 1,
3933 * qca_attr_chip_power_save_failure: Attributes to vendor subcmd
3934 * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite
3935 * information leading to the power save failure.
3937 enum qca_attr_chip_power_save_failure
{
3938 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID
= 0,
3939 /* Reason to cause the power save failure.
3940 * These reasons are represented by
3941 * enum qca_chip_power_save_failure_reason.
3943 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON
= 1,
3946 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST
,
3947 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX
=
3948 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST
- 1,
3952 * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various
3953 * data types for which the stats have to get collected.
3955 enum qca_wlan_vendor_nud_stats_data_pkt_flags
{
3956 QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP
= 1 << 0,
3957 QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS
= 1 << 1,
3958 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE
= 1 << 2,
3959 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4
= 1 << 3,
3960 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6
= 1 << 4,
3961 /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get
3962 * to represent the stats of respective data type.
3964 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN
= 1 << 5,
3965 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK
= 1 << 6,
3966 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK
= 1 << 7,
3969 enum qca_wlan_vendor_nud_stats_set_data_pkt_info
{
3970 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID
= 0,
3971 /* Represents the data packet type to be monitored (u32).
3972 * Host driver tracks the stats corresponding to each data frame
3973 * represented by these flags.
3974 * These data packets are represented by
3975 * enum qca_wlan_vendor_nud_stats_data_pkt_flags
3977 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE
= 1,
3978 /* Name corresponding to the DNS frame for which the respective DNS
3979 * stats have to get monitored (string). Max string length 255.
3981 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME
= 2,
3982 /* source port on which the respective proto stats have to get
3985 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT
= 3,
3986 /* destination port on which the respective proto stats have to get
3989 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT
= 4,
3990 /* IPv4 address for which the destined data packets have to be
3991 * monitored. (in network byte order), u32.
3993 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4
= 5,
3994 /* IPv6 address for which the destined data packets have to be
3995 * monitored. (in network byte order), 16 bytes array.
3997 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6
= 6,
3999 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST
,
4000 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX
=
4001 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST
- 1,
4005 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd
4006 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite
4007 * information to start/stop the NUD statistics collection.
4009 enum qca_attr_nud_stats_set
{
4010 QCA_ATTR_NUD_STATS_SET_INVALID
= 0,
4012 /* Flag to start/stop the NUD statistics collection.
4013 * Start - If included, Stop - If not included
4015 QCA_ATTR_NUD_STATS_SET_START
= 1,
4016 /* IPv4 address of the default gateway (in network byte order), u32 */
4017 QCA_ATTR_NUD_STATS_GW_IPV4
= 2,
4018 /* Represents the list of data packet types to be monitored.
4019 * Host driver tracks the stats corresponding to each data frame
4020 * represented by these flags.
4021 * These data packets are represented by
4022 * enum qca_wlan_vendor_nud_stats_set_data_pkt_info
4024 QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO
= 3,
4027 QCA_ATTR_NUD_STATS_SET_LAST
,
4028 QCA_ATTR_NUD_STATS_SET_MAX
=
4029 QCA_ATTR_NUD_STATS_SET_LAST
- 1,
4032 enum qca_attr_nud_data_stats
{
4033 QCA_ATTR_NUD_DATA_STATS_INVALID
= 0,
4034 /* Data packet type for which the stats are collected (u32).
4035 * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags
4037 QCA_ATTR_NUD_STATS_PKT_TYPE
= 1,
4038 /* Name corresponding to the DNS frame for which the respective DNS
4039 * stats are monitored (string). Max string length 255.
4041 QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME
= 2,
4042 /* source port on which the respective proto stats are collected (u32).
4044 QCA_ATTR_NUD_STATS_PKT_SRC_PORT
= 3,
4045 /* destination port on which the respective proto stats are collected
4048 QCA_ATTR_NUD_STATS_PKT_DEST_PORT
= 4,
4049 /* IPv4 address for which the destined data packets have to be
4050 * monitored. (in network byte order), u32.
4052 QCA_ATTR_NUD_STATS_PKT_DEST_IPV4
= 5,
4053 /* IPv6 address for which the destined data packets have to be
4054 * monitored. (in network byte order), 16 bytes array.
4056 QCA_ATTR_NUD_STATS_PKT_DEST_IPV6
= 6,
4057 /* Data packet Request count received from netdev (u32). */
4058 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV
= 7,
4059 /* Data packet Request count sent to lower MAC from upper MAC (u32). */
4060 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC
= 8,
4061 /* Data packet Request count received by lower MAC from upper MAC
4064 QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC
= 9,
4065 /* Data packet Request count successfully transmitted by the device
4068 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS
= 10,
4069 /* Data packet Response count received by lower MAC (u32) */
4070 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC
= 11,
4071 /* Data packet Response count received by upper MAC (u32) */
4072 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC
= 12,
4073 /* Data packet Response count delivered to netdev (u32) */
4074 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV
= 13,
4075 /* Data Packet Response count that are dropped out of order (u32) */
4076 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP
= 14,
4079 QCA_ATTR_NUD_DATA_STATS_LAST
,
4080 QCA_ATTR_NUD_DATA_STATS_MAX
=
4081 QCA_ATTR_NUD_DATA_STATS_LAST
- 1,
4085 * qca_attr_nud_stats_get: Attributes to vendor subcmd
4086 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite
4087 * NUD statistics collected when queried.
4089 enum qca_attr_nud_stats_get
{
4090 QCA_ATTR_NUD_STATS_GET_INVALID
= 0,
4091 /* ARP Request count from netdev (u32) */
4092 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV
= 1,
4093 /* ARP Request count sent to lower MAC from upper MAC (u32) */
4094 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC
= 2,
4095 /* ARP Request count received by lower MAC from upper MAC (u32) */
4096 QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC
= 3,
4097 /* ARP Request count successfully transmitted by the device (u32) */
4098 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS
= 4,
4099 /* ARP Response count received by lower MAC (u32) */
4100 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC
= 5,
4101 /* ARP Response count received by upper MAC (u32) */
4102 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC
= 6,
4103 /* ARP Response count delivered to netdev (u32) */
4104 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV
= 7,
4105 /* ARP Response count dropped due to out of order reception (u32) */
4106 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP
= 8,
4107 /* Flag indicating if the station's link to the AP is active.
4108 * Active Link - If included, Inactive link - If not included
4110 QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE
= 9,
4111 /* Flag indicating if there is any duplicate address detected (DAD).
4112 * Yes - If detected, No - If not detected.
4114 QCA_ATTR_NUD_STATS_IS_DAD
= 10,
4115 /* List of Data packet types for which the stats are requested.
4116 * This list does not carry ARP stats as they are done by the
4117 * above attributes. Represented by enum qca_attr_nud_data_stats.
4119 QCA_ATTR_NUD_STATS_DATA_PKT_STATS
= 11,
4122 QCA_ATTR_NUD_STATS_GET_LAST
,
4123 QCA_ATTR_NUD_STATS_GET_MAX
=
4124 QCA_ATTR_NUD_STATS_GET_LAST
- 1,
4127 enum qca_wlan_btm_candidate_status
{
4128 QCA_STATUS_ACCEPT
= 0,
4129 QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED
= 1,
4130 QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED
= 2,
4131 QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY
= 3,
4132 QCA_STATUS_REJECT_LOW_RSSI
= 4,
4133 QCA_STATUS_REJECT_HIGH_INTERFERENCE
= 5,
4134 QCA_STATUS_REJECT_UNKNOWN
= 6,
4137 enum qca_wlan_vendor_attr_btm_candidate_info
{
4138 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID
= 0,
4140 /* 6-byte MAC address representing the BSSID of transition candidate */
4141 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID
= 1,
4142 /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status
4143 * returned by the driver. It says whether the BSSID provided in
4144 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by
4145 * the driver, if not it specifies the reason for rejection.
4146 * Note that the user-space can overwrite the transition reject reason
4147 * codes provided by driver based on more information.
4149 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS
= 2,
4152 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST
,
4153 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX
=
4154 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST
- 1,
4157 enum qca_attr_trace_level
{
4158 QCA_ATTR_TRACE_LEVEL_INVALID
= 0,
4160 * Nested array of the following attributes:
4161 * QCA_ATTR_TRACE_LEVEL_MODULE,
4162 * QCA_ATTR_TRACE_LEVEL_MASK.
4164 QCA_ATTR_TRACE_LEVEL_PARAM
= 1,
4166 * Specific QCA host driver module. Please refer to the QCA host
4167 * driver implementation to get the specific module ID.
4169 QCA_ATTR_TRACE_LEVEL_MODULE
= 2,
4170 /* Different trace level masks represented in the QCA host driver. */
4171 QCA_ATTR_TRACE_LEVEL_MASK
= 3,
4174 QCA_ATTR_TRACE_LEVEL_AFTER_LAST
,
4175 QCA_ATTR_TRACE_LEVEL_MAX
=
4176 QCA_ATTR_TRACE_LEVEL_AFTER_LAST
- 1,
4180 * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities
4182 enum qca_wlan_vendor_attr_get_he_capabilities
{
4183 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID
= 0,
4184 /* Whether HE capabilities is supported
4185 * (u8 attribute: 0 = not supported, 1 = supported)
4187 QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED
= 1,
4188 /* HE PHY capabilities, array of 3 u32 values */
4189 QCA_WLAN_VENDOR_ATTR_PHY_CAPAB
= 2,
4190 /* HE MAC capabilities (u32 attribute) */
4191 QCA_WLAN_VENDOR_ATTR_MAC_CAPAB
= 3,
4192 /* HE MCS map (u32 attribute) */
4193 QCA_WLAN_VENDOR_ATTR_HE_MCS
= 4,
4194 /* Number of SS (u32 attribute) */
4195 QCA_WLAN_VENDOR_ATTR_NUM_SS
= 5,
4196 /* RU count (u32 attribute) */
4197 QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK
= 6,
4198 /* PPE threshold data, array of 8 u32 values */
4199 QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD
= 7,
4202 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST
,
4203 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX
=
4204 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST
- 1,
4208 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters
4210 enum qca_wlan_vendor_attr_spectral_scan
{
4211 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID
= 0,
4212 /* Number of times the chip enters spectral scan mode before
4213 * deactivating spectral scans. When set to 0, chip will enter spectral
4214 * scan mode continuously. u32 attribute.
4216 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT
= 1,
4217 /* Spectral scan period. Period increment resolution is 256*Tclk,
4218 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute.
4220 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD
= 2,
4221 /* Spectral scan priority. u32 attribute. */
4222 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY
= 3,
4223 /* Number of FFT data points to compute. u32 attribute. */
4224 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE
= 4,
4225 /* Enable targeted gain change before starting the spectral scan FFT.
4228 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA
= 5,
4229 /* Restart a queued spectral scan. u32 attribute. */
4230 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA
= 6,
4231 /* Noise floor reference number for the calculation of bin power.
4234 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF
= 7,
4235 /* Disallow spectral scan triggers after TX/RX packets by setting
4236 * this delay value to roughly SIFS time period or greater.
4239 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY
= 8,
4240 /* Number of strong bins (inclusive) per sub-channel, below
4241 * which a signal is declared a narrow band tone. u32 attribute.
4243 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR
= 9,
4244 /* Specify the threshold over which a bin is declared strong (for
4245 * scan bandwidth analysis). u32 attribute.
4247 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR
= 10,
4248 /* Spectral scan report mode. u32 attribute. */
4249 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE
= 11,
4250 /* RSSI report mode, if the ADC RSSI is below
4251 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR,
4252 * then FFTs will not trigger, but timestamps and summaries get
4253 * reported. u32 attribute.
4255 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE
= 12,
4256 /* ADC RSSI must be greater than or equal to this threshold (signed dB)
4257 * to ensure spectral scan reporting with normal error code.
4260 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR
= 13,
4261 /* Format of frequency bin magnitude for spectral scan triggered FFTs:
4262 * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)).
4265 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT
= 14,
4266 /* Format of FFT report to software for spectral scan triggered FFTs.
4267 * 0: No FFT report (only spectral scan summary report)
4268 * 1: 2-dword summary of metrics for each completed FFT + spectral scan
4270 * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled
4271 * bins (in-band) per FFT + spectral scan summary report
4272 * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled
4273 * bins (all) per FFT + spectral scan summary report
4276 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE
= 15,
4277 /* Number of LSBs to shift out in order to scale the FFT bins.
4280 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE
= 16,
4281 /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes
4282 * in dBm power. u32 attribute.
4284 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ
= 17,
4285 /* Per chain enable mask to select input ADC for search FFT.
4288 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK
= 18,
4289 /* An unsigned 64-bit integer provided by host driver to identify the
4290 * spectral scan request. This attribute is included in the scan
4291 * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
4292 * and used as an attribute in
4293 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the
4294 * specific scan to be stopped.
4296 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE
= 19,
4297 /* Skip interval for FFT reports. u32 attribute */
4298 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD
= 20,
4299 /* Set to report only one set of FFT results.
4302 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT
= 21,
4303 /* Debug level for spectral module in driver.
4304 * 0 : Verbosity level 0
4305 * 1 : Verbosity level 1
4306 * 2 : Verbosity level 2
4307 * 3 : Matched filterID display
4308 * 4 : One time dump of FFT report
4311 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL
= 22,
4312 /* Type of spectral scan request. u32 attribute.
4313 * It uses values defined in enum
4314 * qca_wlan_vendor_attr_spectral_scan_request_type.
4316 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE
= 23,
4318 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST
,
4319 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX
=
4320 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST
- 1,
4324 * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command
4325 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS.
4327 enum qca_wlan_vendor_attr_spectral_diag_stats
{
4328 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID
= 0,
4329 /* Number of spectral TLV signature mismatches.
4332 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH
= 1,
4333 /* Number of spectral phyerror events with insufficient length when
4334 * parsing for secondary 80 search FFT report. u64 attribute.
4336 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN
= 2,
4337 /* Number of spectral phyerror events without secondary 80
4338 * search FFT report. u64 attribute.
4340 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT
= 3,
4341 /* Number of spectral phyerror events with vht operation segment 1 id
4342 * mismatches in search fft report. u64 attribute.
4344 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH
= 4,
4345 /* Number of spectral phyerror events with vht operation segment 2 id
4346 * mismatches in search fft report. u64 attribute.
4348 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH
= 5,
4350 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST
,
4351 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX
=
4352 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST
- 1,
4356 * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command
4357 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO.
4359 enum qca_wlan_vendor_attr_spectral_cap
{
4360 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID
= 0,
4361 /* Flag attribute to indicate phydiag capability */
4362 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG
= 1,
4363 /* Flag attribute to indicate radar detection capability */
4364 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR
= 2,
4365 /* Flag attribute to indicate spectral capability */
4366 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL
= 3,
4367 /* Flag attribute to indicate advanced spectral capability */
4368 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL
= 4,
4369 /* Spectral hardware generation. u32 attribute.
4370 * It uses values defined in enum
4371 * qca_wlan_vendor_spectral_scan_cap_hw_gen.
4373 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN
= 5,
4375 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST
,
4376 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX
=
4377 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST
- 1,
4381 * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command
4382 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS.
4384 enum qca_wlan_vendor_attr_spectral_scan_status
{
4385 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID
= 0,
4386 /* Flag attribute to indicate whether spectral scan is enabled */
4387 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED
= 1,
4388 /* Flag attribute to indicate whether spectral scan is in progress*/
4389 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE
= 2,
4391 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST
,
4392 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX
=
4393 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST
- 1,
4397 * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for
4398 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd
4399 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the
4400 * spectral scan request types.
4401 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to
4402 * set the spectral parameters and start scan.
4403 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to
4404 * only set the spectral parameters.
4405 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to
4406 * only start the spectral scan.
4408 enum qca_wlan_vendor_attr_spectral_scan_request_type
{
4409 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG
,
4410 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN
,
4411 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG
,
4415 * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for
4416 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd
4417 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the
4418 * spectral hardware generation.
4419 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1
4420 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2
4421 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3
4423 enum qca_wlan_vendor_spectral_scan_cap_hw_gen
{
4424 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1
= 0,
4425 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2
= 1,
4426 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3
= 2,
4429 enum qca_wlan_vendor_tos
{
4430 QCA_WLAN_VENDOR_TOS_BK
= 0,
4431 QCA_WLAN_VENDOR_TOS_BE
= 1,
4432 QCA_WLAN_VENDOR_TOS_VI
= 2,
4433 QCA_WLAN_VENDOR_TOS_VO
= 3,
4437 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command
4438 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS.
4440 enum qca_wlan_vendor_attr_active_tos
{
4441 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID
= 0,
4442 /* Type Of Service - Represented by qca_wlan_vendor_tos */
4443 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS
= 1,
4444 /* Flag attribute representing the start (attribute included) or stop
4445 * (attribute not included) of the respective TOS.
4447 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START
= 2,
4450 enum qca_wlan_vendor_hang_reason
{
4451 /* Unspecified reason */
4452 QCA_WLAN_HANG_REASON_UNSPECIFIED
= 0,
4453 /* No Map for the MAC entry for the received frame */
4454 QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND
= 1,
4455 /* Peer deletion timeout happened */
4456 QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT
= 2,
4457 /* Peer unmap timeout */
4458 QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT
= 3,
4459 /* Scan request timed out */
4460 QCA_WLAN_HANG_SCAN_REQ_EXPIRED
= 4,
4461 /* Consecutive Scan attempt failures */
4462 QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES
= 5,
4463 /* Unable to get the message buffer */
4464 QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE
= 6,
4465 /* Current command processing is timedout */
4466 QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT
= 7,
4467 /* Timeout for an ACK from FW for suspend request */
4468 QCA_WLAN_HANG_SUSPEND_TIMEOUT
= 8,
4469 /* Timeout for an ACK from FW for resume request */
4470 QCA_WLAN_HANG_RESUME_TIMEOUT
= 9,
4471 /* Transmission timeout for consecutive data frames */
4472 QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT
= 10,
4473 /* Timeout for the TX completion status of data frame */
4474 QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT
= 11,
4475 /* DXE failure for TX/RX, DXE resource unavailability */
4476 QCA_WLAN_HANG_DXE_FAILURE
= 12,
4477 /* WMI pending commands exceed the maximum count */
4478 QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS
= 13,
4482 * enum qca_wlan_vendor_attr_hang - Used by the vendor command
4483 * QCA_NL80211_VENDOR_SUBCMD_HANG.
4485 enum qca_wlan_vendor_attr_hang
{
4486 QCA_WLAN_VENDOR_ATTR_HANG_INVALID
= 0,
4487 /* Reason for the hang - u32 attribute with a value from enum
4488 * qca_wlan_vendor_hang_reason.
4490 QCA_WLAN_VENDOR_ATTR_HANG_REASON
= 1,
4492 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST
,
4493 QCA_WLAN_VENDOR_ATTR_HANG_MAX
=
4494 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST
- 1,
4498 * enum qca_wlan_vendor_attr_flush_pending - Attributes for
4499 * flushing pending traffic in firmware.
4501 * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address.
4502 * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending
4503 * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK,
4504 * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to
4505 * flush packets with access category.
4507 enum qca_wlan_vendor_attr_flush_pending
{
4508 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID
= 0,
4509 QCA_WLAN_VENDOR_ATTR_PEER_ADDR
= 1,
4510 QCA_WLAN_VENDOR_ATTR_AC
= 2,
4513 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST
,
4514 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX
=
4515 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST
- 1,
4519 * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative
4520 * RF Operating Parameter (RROP) information is available, and if so, at which
4521 * point in the application-driver interaction sequence it can be retrieved by
4522 * the application from the driver. This point may vary by architecture and
4523 * other factors. This is a u16 value.
4525 enum qca_wlan_vendor_attr_rropavail_info
{
4526 /* RROP information is unavailable. */
4527 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE
,
4528 /* RROP information is available and the application can retrieve the
4529 * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
4530 * event from the driver.
4532 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START
,
4533 /* RROP information is available only after a vendor specific scan
4534 * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has
4535 * successfully completed. The application can retrieve the information
4536 * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from
4539 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END
,
4543 * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific
4544 * Representative RF Operating Parameter (RROP) information. It is sent for the
4545 * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is
4546 * intended for use by external Auto Channel Selection applications. It provides
4547 * guidance values for some RF parameters that are used by the system during
4548 * operation. These values could vary by channel, band, radio, and so on.
4550 enum qca_wlan_vendor_attr_rrop_info
{
4551 QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID
= 0,
4553 /* Representative Tx Power List (RTPL) which has an array of nested
4554 * values as per attributes in enum qca_wlan_vendor_attr_rtplinst.
4556 QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL
= 1,
4558 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST
,
4559 QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX
=
4560 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST
- 1
4564 * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list
4565 * entry instances in the Representative Tx Power List (RTPL). It provides
4566 * simplified power values intended for helping external Auto channel Selection
4567 * applications compare potential Tx power performance between channels, other
4568 * operating conditions remaining identical. These values are not necessarily
4569 * the actual Tx power values that will be used by the system. They are also not
4570 * necessarily the max or average values that will be used. Instead, they are
4571 * relative, summarized keys for algorithmic use computed by the driver or
4572 * underlying firmware considering a number of vendor specific factors.
4574 enum qca_wlan_vendor_attr_rtplinst
{
4575 QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID
= 0,
4577 /* Primary channel number (u8) */
4578 QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY
= 1,
4579 /* Representative Tx power in dBm (s32) with emphasis on throughput. */
4580 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT
= 2,
4581 /* Representative Tx power in dBm (s32) with emphasis on range. */
4582 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE
= 3,
4584 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST
,
4585 QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX
=
4586 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST
- 1,
4590 * enum qca_wlan_vendor_attr_config_latency_level - Level for
4591 * wlan latency module.
4593 * There will be various of Wi-Fi functionality like scan/roaming/adaptive
4594 * power saving which would causing data exchange out of service, this
4595 * would be a big impact on latency. For latency sensitive applications over
4596 * Wi-Fi are intolerant to such operations and thus would configure them
4597 * to meet their respective needs. It is well understood by such applications
4598 * that altering the default behavior would degrade the Wi-Fi functionality
4599 * w.r.t the above pointed WLAN operations.
4601 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL:
4602 * Default WLAN operation level which throughput orientated.
4603 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE:
4604 * Use moderate level to improve latency by limit scan duration.
4605 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW:
4606 * Use low latency level to benifit application like concurrent
4607 * downloading or video streaming via constraint scan/adaptive PS.
4608 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW:
4609 * Use ultra low latency level to benefit for gaming/voice
4610 * application via constraint scan/roaming/adaptive PS.
4612 enum qca_wlan_vendor_attr_config_latency_level
{
4613 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID
= 0,
4614 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL
= 1,
4615 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE
= 2,
4616 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW
= 3,
4617 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW
= 4,
4620 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST
,
4621 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX
=
4622 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST
- 1,
4626 * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command
4627 * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
4629 enum qca_wlan_vendor_attr_mac
{
4630 QCA_WLAN_VENDOR_ATTR_MAC_INVALID
= 0,
4632 /* MAC mode info list which has an array of nested values as
4633 * per attributes in enum qca_wlan_vendor_attr_mac_mode_info.
4635 QCA_WLAN_VENDOR_ATTR_MAC_INFO
= 1,
4638 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST
,
4639 QCA_WLAN_VENDOR_ATTR_MAC_MAX
=
4640 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST
- 1,
4644 * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected
4645 * Wi-Fi netdev interface on a respective MAC.
4646 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO.
4648 enum qca_wlan_vendor_attr_mac_iface_info
{
4649 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID
= 0,
4650 /* Wi-Fi netdev's interface index (u32) */
4651 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX
= 1,
4652 /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */
4653 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ
= 2,
4656 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST
,
4657 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX
=
4658 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST
- 1,
4662 * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information.
4663 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the
4664 * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
4666 enum qca_wlan_vendor_attr_mac_info
{
4667 QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID
= 0,
4668 /* Hardware MAC ID associated for the MAC (u32) */
4669 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID
= 1,
4670 /* Band supported by the MAC at a given point.
4671 * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum
4674 QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND
= 2,
4675 /* Refers to list of WLAN netdev interfaces associated with this MAC.
4676 * Represented by enum qca_wlan_vendor_attr_mac_iface_info.
4678 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO
= 3,
4681 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST
,
4682 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX
=
4683 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST
- 1,
4687 * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command
4688 * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET.
4690 enum qca_wlan_vendor_attr_get_logger_features
{
4691 QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID
= 0,
4692 /* Unsigned 32-bit enum value of wifi_logger_supported_features */
4693 QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED
= 1,
4695 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST
,
4696 QCA_WLAN_VENDOR_ATTR_LOGGER_MAX
=
4697 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST
- 1,
4701 * enum wifi_logger_supported_features - Values for supported logger features
4703 enum wifi_logger_supported_features
{
4704 WIFI_LOGGER_MEMORY_DUMP_FEATURE
= (1 << (0)),
4705 WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE
= (1 << (1)),
4706 WIFI_LOGGER_CONNECT_EVENT_FEATURE
= (1 << (2)),
4707 WIFI_LOGGER_POWER_EVENT_FEATURE
= (1 << (3)),
4708 WIFI_LOGGER_WAKE_LOCK_FEATURE
= (1 << (4)),
4709 WIFI_LOGGER_VERBOSE_FEATURE
= (1 << (5)),
4710 WIFI_LOGGER_WATCHDOG_TIMER_FEATURE
= (1 << (6)),
4711 WIFI_LOGGER_DRIVER_DUMP_FEATURE
= (1 << (7)),
4712 WIFI_LOGGER_PACKET_FATE_FEATURE
= (1 << (8)),
4716 * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get
4717 * capabilities features
4719 enum qca_wlan_tdls_caps_features_supported
{
4720 WIFI_TDLS_SUPPORT
= (1 << (0)),
4721 WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT
= (1 << (1)),
4722 WIFI_TDLS_OFFCHANNEL_SUPPORT
= (1 << (2))
4726 * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command
4727 * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES.
4729 enum qca_wlan_vendor_attr_tdls_get_capabilities
{
4730 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID
= 0,
4731 /* Indicates the max concurrent sessions */
4732 /* Unsigned 32-bit value */
4733 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS
,
4734 /* Indicates the support for features */
4735 /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported
4737 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED
,
4740 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST
,
4741 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX
=
4742 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST
- 1,
4746 * enum qca_wlan_offloaded_packets_sending_control - Offload packets control
4747 * command used as value for the attribute
4748 * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL.
4750 enum qca_wlan_offloaded_packets_sending_control
{
4751 QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID
= 0,
4752 QCA_WLAN_OFFLOADED_PACKETS_SENDING_START
,
4753 QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP
4757 * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command
4758 * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS.
4760 enum qca_wlan_vendor_attr_offloaded_packets
{
4761 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID
= 0,
4762 /* Takes valid value from the enum
4763 * qca_wlan_offloaded_packets_sending_control
4764 * Unsigned 32-bit value
4766 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL
,
4767 /* Unsigned 32-bit value */
4768 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID
,
4769 /* array of u8 len: Max packet size */
4770 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA
,
4771 /* 6-byte MAC address used to represent source MAC address */
4772 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR
,
4773 /* 6-byte MAC address used to represent destination MAC address */
4774 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR
,
4775 /* Unsigned 32-bit value, in milli seconds */
4776 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD
,
4779 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST
,
4780 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX
=
4781 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST
- 1,
4785 * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values
4786 * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL.
4788 enum qca_wlan_rssi_monitoring_control
{
4789 QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID
= 0,
4790 QCA_WLAN_RSSI_MONITORING_START
,
4791 QCA_WLAN_RSSI_MONITORING_STOP
,
4795 * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command
4796 * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI.
4798 enum qca_wlan_vendor_attr_rssi_monitoring
{
4799 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID
= 0,
4800 /* Takes valid value from the enum
4801 * qca_wlan_rssi_monitoring_control
4802 * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control
4804 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL
,
4805 /* Unsigned 32-bit value */
4806 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID
,
4807 /* Signed 8-bit value in dBm */
4808 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI
,
4809 /* Signed 8-bit value in dBm */
4810 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI
,
4811 /* attributes to be used/received in callback */
4812 /* 6-byte MAC address used to represent current BSSID MAC address */
4813 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID
,
4814 /* Signed 8-bit value indicating the current RSSI */
4815 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI
,
4817 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST
,
4818 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX
=
4819 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST
- 1,
4823 * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command
4824 * QCA_NL80211_VENDOR_SUBCMD_NDP.
4826 enum qca_wlan_vendor_attr_ndp_params
{
4827 QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID
= 0,
4828 /* Unsigned 32-bit value
4829 * enum of sub commands values in qca_wlan_ndp_sub_cmd
4831 QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD
,
4832 /* Unsigned 16-bit value */
4833 QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID
,
4834 /* NL attributes for data used NDP SUB cmds */
4835 /* Unsigned 32-bit value indicating a service info */
4836 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID
,
4837 /* Unsigned 32-bit value; channel frequency in MHz */
4838 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL
,
4839 /* Interface Discovery MAC address. An array of 6 Unsigned int8 */
4840 QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR
,
4841 /* Interface name on which NDP is being created */
4842 QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR
,
4843 /* Unsigned 32-bit value for security */
4844 /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */
4845 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY
,
4846 /* Unsigned 32-bit value for QoS */
4847 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS
,
4848 /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */
4849 QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO
,
4850 /* Unsigned 32-bit value for NDP instance Id */
4851 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID
,
4852 /* Array of instance Ids */
4853 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY
,
4854 /* Unsigned 32-bit value for initiator/responder NDP response code
4857 QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE
,
4858 /* NDI MAC address. An array of 6 Unsigned int8 */
4859 QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR
,
4860 /* Unsigned 32-bit value errors types returned by driver
4861 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
4862 * NanStatusType includes these values.
4864 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE
,
4865 /* Unsigned 32-bit value error values returned by driver
4866 * The nan_i.h in AOSP project platform/hardware/qcom/wlan
4867 * NanInternalStatusType includes these values.
4869 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE
,
4870 /* Unsigned 32-bit value for Channel setup configuration
4871 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
4872 * NanDataPathChannelCfg includes these values.
4874 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG
,
4875 /* Unsigned 32-bit value for Cipher Suite Shared Key Type */
4876 QCA_WLAN_VENDOR_ATTR_NDP_CSID
,
4877 /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */
4878 QCA_WLAN_VENDOR_ATTR_NDP_PMK
,
4879 /* Security Context Identifier that contains the PMKID
4880 * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes
4882 QCA_WLAN_VENDOR_ATTR_NDP_SCID
,
4883 /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */
4884 QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE
,
4885 /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */
4886 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME
,
4887 /* Unsigned 32-bit bitmap indicating schedule update
4889 * BIT_1: Channel list update
4891 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON
,
4892 /* Unsigned 32-bit value for NSS */
4893 QCA_WLAN_VENDOR_ATTR_NDP_NSS
,
4894 /* Unsigned 32-bit value for NUMBER NDP CHANNEL */
4895 QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS
,
4896 /* Unsigned 32-bit value for CHANNEL BANDWIDTH
4897 * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz
4899 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH
,
4900 /* Array of channel/band width */
4901 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO
,
4902 /* IPv6 address used by NDP (in network byte order), 16 bytes array.
4903 * This attribute is used and optional for ndp request, ndp response,
4904 * ndp indication, and ndp confirm.
4906 QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR
= 27,
4907 /* Unsigned 16-bit value indicating transport port used by NDP.
4908 * This attribute is used and optional for ndp response, ndp indication,
4911 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT
= 28,
4912 /* Unsigned 8-bit value indicating protocol used by NDP and assigned by
4913 * the Internet Assigned Numbers Authority (IANA) as per:
4914 * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
4915 * This attribute is used and optional for ndp response, ndp indication,
4918 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL
= 29,
4921 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST
,
4922 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX
=
4923 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST
- 1,
4926 enum qca_wlan_ndp_sub_cmd
{
4927 QCA_WLAN_VENDOR_ATTR_NDP_INVALID
= 0,
4928 /* Command to create a NAN data path interface */
4929 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE
= 1,
4930 /* Command to delete a NAN data path interface */
4931 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE
= 2,
4932 /* Command to initiate a NAN data path session */
4933 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST
= 3,
4934 /* Command to notify if the NAN data path session was sent */
4935 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE
= 4,
4936 /* Command to respond to NAN data path session */
4937 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST
= 5,
4938 /* Command to notify on the responder about the response */
4939 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE
= 6,
4940 /* Command to initiate a NAN data path end */
4941 QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST
= 7,
4942 /* Command to notify the if end request was sent */
4943 QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE
= 8,
4944 /* Command to notify the peer about the end request */
4945 QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND
= 9,
4946 /* Command to confirm the NAN data path session is complete */
4947 QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND
= 10,
4948 /* Command to indicate the peer about the end request being received */
4949 QCA_WLAN_VENDOR_ATTR_NDP_END_IND
= 11,
4950 /* Command to indicate the peer of schedule update */
4951 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND
= 12
4955 * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command
4956 * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD.
4958 enum qca_wlan_vendor_attr_nd_offload
{
4959 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID
= 0,
4960 /* Flag to set Neighbour Discovery offload */
4961 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG
,
4963 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST
,
4964 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX
=
4965 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST
- 1,
4969 * enum packet_filter_sub_cmd - Packet filter sub commands
4971 enum packet_filter_sub_cmd
{
4973 * Write packet filter program and/or data. The driver/firmware should
4974 * disable APF before writing into local buffer and re-enable APF after
4977 QCA_WLAN_SET_PACKET_FILTER
= 1,
4978 /* Get packet filter feature capabilities from driver */
4979 QCA_WLAN_GET_PACKET_FILTER
= 2,
4981 * Write packet filter program and/or data. User space will send the
4982 * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command
4983 * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key
4984 * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over
4985 * enable/disable is given to user space with this command. Also,
4986 * user space sends the length of program portion in the buffer within
4987 * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH.
4989 QCA_WLAN_WRITE_PACKET_FILTER
= 3,
4990 /* Read packet filter program and/or data */
4991 QCA_WLAN_READ_PACKET_FILTER
= 4,
4992 /* Enable APF feature */
4993 QCA_WLAN_ENABLE_PACKET_FILTER
= 5,
4994 /* Disable APF feature */
4995 QCA_WLAN_DISABLE_PACKET_FILTER
= 6,
4999 * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by
5000 * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER.
5002 enum qca_wlan_vendor_attr_packet_filter
{
5003 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID
= 0,
5004 /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */
5005 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD
,
5006 /* Unsigned 32-bit value indicating the packet filter version */
5007 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION
,
5008 /* Unsigned 32-bit value indicating the packet filter id */
5009 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID
,
5011 * Unsigned 32-bit value indicating the packet filter size including
5014 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE
,
5015 /* Unsigned 32-bit value indicating the packet filter current offset */
5016 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET
,
5017 /* Program and/or data in bytes */
5018 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM
,
5019 /* Unsigned 32-bit value of the length of the program section in packet
5022 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH
= 7,
5025 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST
,
5026 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX
=
5027 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST
- 1,
5031 * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command
5032 * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE.
5034 enum qca_wlan_vendor_drv_info
{
5035 QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID
= 0,
5036 /* Maximum Message size info between firmware & HOST
5037 * Unsigned 32-bit value
5039 QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE
,
5041 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST
,
5042 QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX
=
5043 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST
- 1,
5047 * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor
5048 * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS.
5050 enum qca_wlan_vendor_attr_wake_stats
{
5051 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID
= 0,
5052 /* Unsigned 32-bit value indicating the total count of wake event */
5053 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE
,
5054 /* Array of individual wake count, each index representing wake reason
5056 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR
,
5057 /* Unsigned 32-bit value representing wake count array */
5058 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ
,
5059 /* Unsigned 32-bit total wake count value of driver/fw */
5060 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE
,
5061 /* Array of wake stats of driver/fw */
5062 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR
,
5063 /* Unsigned 32-bit total wake count value of driver/fw */
5064 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ
,
5065 /* Unsigned 32-bit total wake count value of packets received */
5066 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE
,
5067 /* Unsigned 32-bit wake count value unicast packets received */
5068 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT
,
5069 /* Unsigned 32-bit wake count value multicast packets received */
5070 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT
,
5071 /* Unsigned 32-bit wake count value broadcast packets received */
5072 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT
,
5073 /* Unsigned 32-bit wake count value of ICMP packets */
5074 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT
,
5075 /* Unsigned 32-bit wake count value of ICMP6 packets */
5076 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT
,
5077 /* Unsigned 32-bit value ICMP6 router advertisement */
5078 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA
,
5079 /* Unsigned 32-bit value ICMP6 neighbor advertisement */
5080 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA
,
5081 /* Unsigned 32-bit value ICMP6 neighbor solicitation */
5082 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS
,
5083 /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */
5084 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT
,
5085 /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */
5086 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT
,
5087 /* Unsigned 32-bit wake count value of receive side multicast */
5088 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT
,
5089 /* Unsigned 32-bit wake count value of a given RSSI breach */
5090 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT
,
5091 /* Unsigned 32-bit wake count value of low RSSI */
5092 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT
,
5093 /* Unsigned 32-bit value GSCAN count */
5094 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT
,
5095 /* Unsigned 32-bit value PNO complete count */
5096 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT
,
5097 /* Unsigned 32-bit value PNO match count */
5098 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT
,
5100 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST
,
5101 QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX
=
5102 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST
- 1,
5106 * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set
5107 * cmd value. Used for NL attributes for data used by
5108 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
5110 enum qca_wlan_vendor_attr_thermal_cmd
{
5111 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID
= 0,
5112 /* The value of command, driver will implement different operations
5113 * according to this value. It uses values defined in
5114 * enum qca_wlan_vendor_attr_thermal_cmd_type.
5117 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE
= 1,
5120 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST
,
5121 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX
=
5122 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST
- 1
5126 * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for
5127 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd
5128 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the
5129 * thermal command types sent to driver.
5130 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to
5131 * get thermal shutdown configuration parameters for display. Parameters
5132 * responded from driver are defined in
5133 * enum qca_wlan_vendor_attr_get_thermal_params_rsp.
5134 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to
5135 * get temperature. Host should respond with a temperature data. It is defined
5136 * in enum qca_wlan_vendor_attr_thermal_get_temperature.
5137 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal
5139 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal
5142 enum qca_wlan_vendor_attr_thermal_cmd_type
{
5143 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS
,
5144 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE
,
5145 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND
,
5146 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME
,
5150 * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes
5151 * to get chip temperature by user.
5152 * enum values are used for NL attributes for data used by
5153 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used
5154 * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
5156 enum qca_wlan_vendor_attr_thermal_get_temperature
{
5157 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID
= 0,
5158 /* Temperature value (degree Celsius) from driver.
5161 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA
,
5164 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST
,
5165 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX
=
5166 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST
- 1,
5170 * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes
5171 * to get configuration parameters of thermal shutdown feature. Enum values are
5172 * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data
5173 * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
5175 enum qca_wlan_vendor_attr_get_thermal_params_rsp
{
5176 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID
= 0,
5177 /* Indicate if the thermal shutdown feature is enabled.
5178 * NLA_FLAG attribute.
5180 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN
,
5181 /* Indicate if the auto mode is enabled.
5182 * Enable: Driver triggers the suspend/resume action.
5183 * Disable: User space triggers the suspend/resume action.
5184 * NLA_FLAG attribute.
5186 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN
,
5187 /* Thermal resume threshold (degree Celsius). Issue the resume command
5188 * if the temperature value is lower than this threshold.
5191 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH
,
5192 /* Thermal warning threshold (degree Celsius). FW reports temperature
5193 * to driver if it's higher than this threshold.
5196 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH
,
5197 /* Thermal suspend threshold (degree Celsius). Issue the suspend command
5198 * if the temperature value is higher than this threshold.
5201 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH
,
5202 /* FW reports temperature data periodically at this interval (ms).
5205 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE
,
5208 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST
,
5209 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX
=
5210 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST
- 1,
5214 * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to
5215 * report thermal events from driver to user space.
5216 * enum values are used for NL attributes for data used by
5217 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command.
5219 enum qca_wlan_vendor_attr_thermal_event
{
5220 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID
= 0,
5221 /* Temperature value (degree Celsius) from driver.
5224 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE
,
5225 /* Indication of resume completion from power save mode.
5226 * NLA_FLAG attribute.
5228 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE
,
5231 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST
,
5232 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX
=
5233 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST
- 1,
5237 * enum he_fragmentation_val - HE fragmentation support values
5238 * Indicates level of dynamic fragmentation that is supported by
5239 * a STA as a recipient.
5240 * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2
5241 * (HE MAC Capabilities Information field) and are used in HE Capabilities
5242 * element to advertise the support. These values are validated in the driver
5243 * to check the device capability and advertised in the HE Capabilities
5244 * element. These values are used to configure testbed device to allow the
5245 * advertised hardware capabilities to be downgraded for testing purposes.
5247 * @HE_FRAG_DISABLE: no support for dynamic fragmentation
5248 * @HE_FRAG_LEVEL1: support for dynamic fragments that are
5249 * contained within an MPDU or S-MPDU, no support for dynamic fragments
5250 * within an A-MPDU that is not an S-MPDU.
5251 * @HE_FRAG_LEVEL2: support for dynamic fragments that are
5252 * contained within an MPDU or S-MPDU and support for up to one dynamic
5253 * fragment for each MSDU, each A-MSDU if supported by the recipient, and
5254 * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an
5256 * @HE_FRAG_LEVEL3: support for dynamic fragments that are
5257 * contained within an MPDU or S-MPDU and support for multiple dynamic
5258 * fragments for each MSDU and for each A-MSDU if supported by the
5259 * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic
5260 * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU.
5262 enum he_fragmentation_val
{
5270 * enum he_mcs_config - HE MCS support configuration
5272 * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth.
5273 * These values are used in driver to configure the HE MCS map to advertise
5274 * Tx/Rx MCS map in HE capability and these values are applied for all the
5275 * streams supported by the device. To configure MCS for different bandwidths,
5276 * vendor command needs to be sent using this attribute with appropriate value.
5277 * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS
5278 * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11
5279 * send this command using HE MCS config attribute with value HE_160_MCS0_11.
5280 * These values are used to configure testbed device to allow the advertised
5281 * hardware capabilities to be downgraded for testing purposes. The enum values
5282 * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and
5283 * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map.
5284 * These values are validated in the driver before setting the MCS map and
5285 * driver returns error if the input is other than these enum values.
5287 * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7
5288 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9
5289 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11
5290 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7
5291 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9
5292 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11
5293 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7
5294 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9
5295 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11
5297 enum he_mcs_config
{
5304 HE_80P80_MCS0_7
= 8,
5305 HE_80P80_MCS0_9
= 9,
5306 HE_80P80_MCS0_11
= 10,
5310 * enum qca_wlan_ba_session_config - BA session configuration
5312 * Indicates the configuration values for BA session configuration attribute.
5314 * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration.
5315 * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID.
5317 enum qca_wlan_ba_session_config
{
5318 QCA_WLAN_ADD_BA
= 1,
5319 QCA_WLAN_DELETE_BA
= 2,
5323 * enum qca_wlan_ac_type - Access category type
5325 * Indicates the access category type value.
5327 * @QCA_WLAN_AC_BE: BE access category
5328 * @QCA_WLAN_AC_BK: BK access category
5329 * @QCA_WLAN_AC_VI: VI access category
5330 * @QCA_WLAN_AC_VO: VO access category
5331 * @QCA_WLAN_AC_ALL: All ACs
5333 enum qca_wlan_ac_type
{
5338 QCA_WLAN_AC_ALL
= 4,
5342 * enum qca_wlan_he_ltf_cfg - HE LTF configuration
5344 * Indicates the HE LTF configuration value.
5346 * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF,
5347 * based on the GI setting
5348 * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF
5349 * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF
5350 * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF
5352 enum qca_wlan_he_ltf_cfg
{
5353 QCA_WLAN_HE_LTF_AUTO
= 0,
5354 QCA_WLAN_HE_LTF_1X
= 1,
5355 QCA_WLAN_HE_LTF_2X
= 2,
5356 QCA_WLAN_HE_LTF_4X
= 3,
5359 /* Attributes for data used by
5360 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
5362 enum qca_wlan_vendor_attr_wifi_test_config
{
5363 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID
= 0,
5364 /* 8-bit unsigned value to configure the driver to enable/disable
5365 * WMM feature. This attribute is used to configure testbed device.
5366 * 1-enable, 0-disable
5368 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE
= 1,
5370 /* 8-bit unsigned value to configure the driver to accept/reject
5371 * the addba request from peer. This attribute is used to configure
5372 * the testbed device.
5373 * 1-accept addba, 0-reject addba
5375 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ
= 2,
5377 /* 8-bit unsigned value to configure the driver to send or not to
5378 * send the addba request to peer.
5379 * This attribute is used to configure the testbed device.
5380 * 1-send addba, 0-do not send addba
5382 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ
= 3,
5384 /* 8-bit unsigned value to indicate the HE fragmentation support.
5385 * Uses enum he_fragmentation_val values.
5386 * This attribute is used to configure the testbed device to
5387 * allow the advertised hardware capabilities to be downgraded
5388 * for testing purposes.
5390 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION
= 4,
5392 /* 8-bit unsigned value to indicate the HE MCS support.
5393 * Uses enum he_mcs_config values.
5394 * This attribute is used to configure the testbed device to
5395 * allow the advertised hardware capabilities to be downgraded
5396 * for testing purposes.
5398 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS
= 5,
5400 /* 8-bit unsigned value to configure the driver to allow or not to
5401 * allow the connection with WEP/TKIP in HT/VHT/HE modes.
5402 * This attribute is used to configure the testbed device.
5403 * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP.
5405 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE
= 6,
5407 /* 8-bit unsigned value to configure the driver to add a
5408 * new BA session or delete the existing BA session for
5409 * given TID. ADDBA command uses the buffer size and TID
5410 * configuration if user specifies the values else default
5411 * value for buffer size is used for all TIDs if the TID
5412 * also not specified. For DEL_BA command TID value is
5413 * required to process the command.
5414 * Uses enum qca_wlan_ba_session_config values.
5415 * This attribute is used to configure the testbed device.
5417 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION
= 7,
5419 /* 8-bit unsigned value to configure the buffer size in addba
5420 * request and response frames.
5421 * This attribute is used to configure the testbed device.
5422 * The range of the value is 0 to 255.
5424 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE
= 8,
5426 /* 8-bit unsigned value to configure the buffer size in addba
5427 * request and response frames.
5428 * This attribute is used to configure the testbed device.
5430 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID
= 9,
5432 /* 8-bit unsigned value to configure the no ack policy.
5433 * To configure no ack policy, access category value is
5434 * required to process the command.
5435 * This attribute is used to configure the testbed device.
5436 * 1 - enable no ack, 0 - disable no ack.
5438 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK
= 10,
5440 /* 8-bit unsigned value to configure the AC for no ack policy
5441 * This attribute is used to configure the testbed device.
5442 * Uses the enum qca_wlan_ac_type values.
5444 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC
= 11,
5446 /* 8-bit unsigned value to configure the HE LTF
5447 * This attribute is used to configure the testbed device.
5448 * Uses the enum qca_wlan_he_ltf_cfg values.
5450 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF
= 12,
5452 /* 8-bit unsigned value to configure the tx beamformee.
5453 * This attribute is used to configure the testbed device.
5454 * 1-enable, 0-disable.
5456 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE
= 13,
5459 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST
,
5460 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX
=
5461 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST
- 1,
5465 * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command
5466 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5467 * The user can add/delete the filter by specifying the BSSID/STA MAC address in
5468 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in
5469 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in
5470 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the
5471 * statistics of an unassociated station by specifying the MAC address in
5472 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in
5473 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in
5474 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get
5475 * the statistics of all unassociated stations by specifying the Broadcast MAC
5476 * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with
5477 * above procedure. In the response, driver shall specify statistics
5478 * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS.
5480 enum qca_wlan_vendor_attr_bss_filter
{
5481 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID
= 0,
5482 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR
= 1,
5483 /* Other BSS filter type, unsigned 8 bit value. One of the values
5484 * in enum qca_wlan_vendor_bss_filter_type.
5486 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE
= 2,
5487 /* Other BSS filter action, unsigned 8 bit value. One of the values
5488 * in enum qca_wlan_vendor_bss_filter_action.
5490 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION
= 3,
5491 /* Array of nested attributes where each entry is the statistics
5492 * information of the specified station that belong to another BSS.
5493 * Attributes for each entry are taken from enum
5494 * qca_wlan_vendor_bss_filter_sta_stats.
5495 * Other BSS station configured in
5496 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type
5497 * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA.
5498 * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER
5499 * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET.
5501 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS
= 4,
5504 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST
,
5505 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX
=
5506 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST
- 1,
5510 * enum qca_wlan_vendor_bss_filter_type - Type of
5511 * filter used in other BSS filter operations. Used by the vendor command
5512 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5514 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter
5515 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter
5517 enum qca_wlan_vendor_bss_filter_type
{
5518 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID
,
5519 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA
,
5523 * enum qca_wlan_vendor_bss_filter_action - Type of
5524 * action in other BSS filter operations. Used by the vendor command
5525 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5527 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter
5528 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter
5529 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics
5531 enum qca_wlan_vendor_bss_filter_action
{
5532 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD
,
5533 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL
,
5534 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET
,
5538 * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for
5539 * the statistics of a specific unassociated station belonging to another BSS.
5540 * The statistics provides information of the unassociated station
5541 * filtered by other BSS operation - such as MAC, signal value.
5542 * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
5544 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station.
5545 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength
5546 * of the station. Unsigned 8 bit number containing RSSI.
5547 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host
5548 * driver for the last received RSSI. Unsigned 64 bit number containing
5549 * nanoseconds from the boottime.
5551 enum qca_wlan_vendor_bss_filter_sta_stats
{
5552 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID
= 0,
5553 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC
= 1,
5554 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI
= 2,
5555 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS
= 3,
5558 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST
,
5559 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX
=
5560 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST
- 1
5563 #endif /* QCA_VENDOR_H */