fs: separate CONFIG_FS_{FAT, EXT4} from CONFIG_CMD_{FAT, EXT*}

[people/ms/u-boot.git] / README

diff --git a/README b/README
index 4428205b86aa5273c95ca6f820667ffb5d63e2d8..22fd6b761ef82090df1fc55f5eefb653c5620489 100644 (file)
--- a/README
+++ b/README
@@ -363,6 +363,12 @@ The following options need to be configured:
                ICache only when Code runs from RAM.
 
 - 85xx CPU Options:
                ICache only when Code runs from RAM.
 
 - 85xx CPU Options:

+               CONFIG_SYS_PPC64
+
+               Specifies that the core is a 64-bit PowerPC implementation (implements
+               the "64" category of the Power ISA). This is necessary for ePAPR
+               compliance, among other possible reasons.
+

                CONFIG_SYS_FSL_TBCLK_DIV
 
                Defines the core time base clock divider ratio compared to the
                CONFIG_SYS_FSL_TBCLK_DIV
 
                Defines the core time base clock divider ratio compared to the


@@ -383,6 +389,31 @@ The following options need to be configured:
                symbol should be set to the TLB1 entry to be used for this
                purpose.
 
                symbol should be set to the TLB1 entry to be used for this
                purpose.
 

+               CONFIG_SYS_FSL_ERRATUM_A004510
+
+               Enables a workaround for erratum A004510.  If set,
+               then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
+               CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
+
+               CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
+               CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
+
+               Defines one or two SoC revisions (low 8 bits of SVR)
+               for which the A004510 workaround should be applied.
+
+               The rest of SVR is either not relevant to the decision
+               of whether the erratum is present (e.g. p2040 versus
+               p2041) or is implied by the build target, which controls
+               whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
+
+               See Freescale App Note 4493 for more information about
+               this erratum.
+
+               CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
+
+               This is the value to write into CCSR offset 0x18600
+               according to the A004510 workaround.
+

 - Generic CPU options:
                CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
 - Generic CPU options:
                CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 


@@ -679,6 +710,8 @@ The following options need to be configured:
 - Boot Delay:  CONFIG_BOOTDELAY - in seconds
                Delay before automatically booting the default image;
                set to -1 to disable autoboot.
 - Boot Delay:  CONFIG_BOOTDELAY - in seconds
                Delay before automatically booting the default image;
                set to -1 to disable autoboot.

+               set to -2 to autoboot with no delay and not check for abort
+               (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).

 
                See doc/README.autoboot for these options that
                work with CONFIG_BOOTDELAY. None are required.
 
                See doc/README.autoboot for these options that
                work with CONFIG_BOOTDELAY. None are required.


@@ -774,9 +807,11 @@ The following options need to be configured:
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_EXPORTENV    * export the environment
                CONFIG_CMD_EEPROM       * EEPROM read/write support
                CONFIG_CMD_ELF          * bootelf, bootvx
                CONFIG_CMD_EXPORTENV    * export the environment

+               CONFIG_CMD_EXT2         * ext2 command support
+               CONFIG_CMD_EXT4         * ext4 command support

                CONFIG_CMD_SAVEENV        saveenv
                CONFIG_CMD_FDC          * Floppy Disk Support
                CONFIG_CMD_SAVEENV        saveenv
                CONFIG_CMD_FDC          * Floppy Disk Support

-               CONFIG_CMD_FAT          * FAT partition support
+               CONFIG_CMD_FAT          * FAT command support

                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support


@@ -789,6 +824,7 @@ The following options need to be configured:
                CONFIG_CMD_IMLS           List all found images
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_IMLS           List all found images
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment

+               CONFIG_CMD_INI          * import data from an ini file into the env

                CONFIG_CMD_IRQ          * irqinfo
                CONFIG_CMD_ITEST          Integer/string test of 2 values
                CONFIG_CMD_JFFS2        * JFFS2 Support
                CONFIG_CMD_IRQ          * irqinfo
                CONFIG_CMD_ITEST          Integer/string test of 2 values
                CONFIG_CMD_JFFS2        * JFFS2 Support


@@ -830,7 +866,8 @@ The following options need to be configured:
                CONFIG_CMD_SPI          * SPI serial bus support
                CONFIG_CMD_TFTPSRV      * TFTP transfer in server mode
                CONFIG_CMD_TFTPPUT      * TFTP put command (upload)
                CONFIG_CMD_SPI          * SPI serial bus support
                CONFIG_CMD_TFTPSRV      * TFTP transfer in server mode
                CONFIG_CMD_TFTPPUT      * TFTP put command (upload)

-               CONFIG_CMD_TIME         * run command and report execution time
+               CONFIG_CMD_TIME         * run command and report execution time (ARM specific)
+               CONFIG_CMD_TIMER        * access to the system tick timer

                CONFIG_CMD_USB          * USB support
                CONFIG_CMD_CDP          * Cisco Discover Protocol support
                CONFIG_CMD_MFSL         * Microblaze FSL support
                CONFIG_CMD_USB          * USB support
                CONFIG_CMD_CDP          * Cisco Discover Protocol support
                CONFIG_CMD_MFSL         * Microblaze FSL support


@@ -1055,7 +1092,7 @@ The following options need to be configured:
                CONFIG_CALXEDA_XGMAC
                Support for the Calxeda XGMAC device
 
                CONFIG_CALXEDA_XGMAC
                Support for the Calxeda XGMAC device
 

-               CONFIG_DRIVER_LAN91C96
+               CONFIG_LAN91C96

                Support for SMSC's LAN91C96 chips.
 
                        CONFIG_LAN91C96_BASE
                Support for SMSC's LAN91C96 chips.
 
                        CONFIG_LAN91C96_BASE


@@ -1065,7 +1102,7 @@ The following options need to be configured:
                        CONFIG_LAN91C96_USE_32_BIT
                        Define this to enable 32 bit addressing
 
                        CONFIG_LAN91C96_USE_32_BIT
                        Define this to enable 32 bit addressing
 

-               CONFIG_DRIVER_SMC91111
+               CONFIG_SMC91111

                Support for SMSC's LAN91C111 chip
 
                        CONFIG_SMC91111_BASE
                Support for SMSC's LAN91C111 chip
 
                        CONFIG_SMC91111_BASE


@@ -1239,6 +1276,9 @@ The following options need to be configured:
                viewport is supported.
                To enable the ULPI layer support, define CONFIG_USB_ULPI and
                CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
                viewport is supported.
                To enable the ULPI layer support, define CONFIG_USB_ULPI and
                CONFIG_USB_ULPI_VIEWPORT in your board configuration file.

+               If your ULPI phy needs a different reference clock than the
+               standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
+               the appropriate value in Hz.

 
 - MMC Support:
                The MMC controller on the Intel PXA is supported. To
 
 - MMC Support:
                The MMC controller on the Intel PXA is supported. To


@@ -1284,6 +1324,13 @@ The following options need to be configured:
                This will also enable the command "fatwrite" enabling the
                user to write files to FAT.
 
                This will also enable the command "fatwrite" enabling the
                user to write files to FAT.
 

+CBFS (Coreboot Filesystem) support
+               CONFIG_CMD_CBFS
+
+               Define this to enable support for reading from a Coreboot
+               filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
+               and cbfsload.
+

 - Keyboard Support:
                CONFIG_ISA_KEYBOARD
 
 - Keyboard Support:
                CONFIG_ISA_KEYBOARD
 


@@ -1458,6 +1505,12 @@ The following options need to be configured:
                can be displayed via the splashscreen support or the
                bmp command.
 
                can be displayed via the splashscreen support or the
                bmp command.
 

+- Do compresssing for memory range:
+               CONFIG_CMD_ZIP
+
+               If this option is set, it would use zlib deflate method
+               to compress the specified memory at its best effort.
+

 - Compression support:
                CONFIG_BZIP2
 
 - Compression support:
                CONFIG_BZIP2
 


@@ -2131,8 +2184,8 @@ The following options need to be configured:
                following board configurations are known to be
                "pRAM-clean":
 
                following board configurations are known to be
                "pRAM-clean":
 

-                       ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
-                       HERMES, IP860, RPXlite, LWMON, LANTEC,
+                       IVMS8, IVML24, SPD8xx, TQM8xxL,
+                       HERMES, IP860, RPXlite, LWMON,

                        FLAGADM, TQM8260
 
 - Error Recovery:
                        FLAGADM, TQM8260
 
 - Error Recovery:


@@ -2353,6 +2406,31 @@ The following options need to be configured:
                 29,916,167 26,005,792  bootm_start
                 30,361,327    445,160  start_kernel
 
                 29,916,167 26,005,792  bootm_start
                 30,361,327    445,160  start_kernel
 

+               CONFIG_CMD_BOOTSTAGE
+               Add a 'bootstage' command which supports printing a report
+               and un/stashing of bootstage data.
+
+               CONFIG_BOOTSTAGE_FDT
+               Stash the bootstage information in the FDT. A root 'bootstage'
+               node is created with each bootstage id as a child. Each child
+               has a 'name' property and either 'mark' containing the
+               mark time in microsecond, or 'accum' containing the
+               accumulated time for that bootstage id in microseconds.
+               For example:
+
+               bootstage {
+                       154 {
+                               name = "board_init_f";
+                               mark = <3575678>;
+                       };
+                       170 {
+                               name = "lcd";
+                               accum = <33482>;
+                       };
+               };
+
+               Code in the Linux kernel can find this in /proc/devicetree.
+

 Legacy uImage format:
 
   Arg  Where                   When
 Legacy uImage format:
 
   Arg  Where                   When


@@ -2572,6 +2650,15 @@ FIT uImage format:
                CONFIG_SYS_SPL_MALLOC_SIZE
                The size of the malloc pool used in SPL.
 
                CONFIG_SYS_SPL_MALLOC_SIZE
                The size of the malloc pool used in SPL.
 

+               CONFIG_SPL_FRAMEWORK
+               Enable the SPL framework under common/.  This framework
+               supports MMC, NAND and YMODEM loading of U-Boot and NAND
+               NAND loading of the Linux Kernel.
+
+               CONFIG_SPL_DISPLAY_PRINT
+               For ARM, enable an optional function to print more information
+               about the running system.
+

                CONFIG_SPL_LIBCOMMON_SUPPORT
                Support for common/libcommon.o in SPL binary
 
                CONFIG_SPL_LIBCOMMON_SUPPORT
                Support for common/libcommon.o in SPL binary
 


@@ -2635,6 +2722,9 @@ FIT uImage format:
                CONFIG_SPL_SPI_SUPPORT
                Support for drivers/spi/libspi.o in SPL binary
 
                CONFIG_SPL_SPI_SUPPORT
                Support for drivers/spi/libspi.o in SPL binary
 

+               CONFIG_SPL_RAM_DEVICE
+               Support for running image already present in ram, in SPL binary
+

                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 
                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 


@@ -3100,12 +3190,12 @@ to save the current settings.
          These two #defines specify the address and size of the
          environment area within the remote memory space. The
          local device can get the environment from remote memory
          These two #defines specify the address and size of the
          environment area within the remote memory space. The
          local device can get the environment from remote memory

-         space by SRIO or other links.
+         space by SRIO or PCIE links.

 
 BE CAREFUL! For some special cases, the local device can not use
 "saveenv" command. For example, the local device will get the
 
 BE CAREFUL! For some special cases, the local device can not use
 "saveenv" command. For example, the local device will get the

-environment stored in a remote NOR flash by SRIO link, but it can
-not erase, write this NOR flash by SRIO interface.
+environment stored in a remote NOR flash by SRIO or PCIE link,
+but it can not erase, write this NOR flash by SRIO or PCIE interface.

 
 - CONFIG_ENV_IS_IN_NAND:
 
 
 - CONFIG_ENV_IS_IN_NAND:
 


@@ -3553,9 +3643,9 @@ within that device.
 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
        Specifies that QE/FMAN firmware is located in the remote (master)
        memory space.   CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
        Specifies that QE/FMAN firmware is located in the remote (master)
        memory space.   CONFIG_SYS_FMAN_FW_ADDR is a virtual address which

-       can be mapped from slave TLB->slave LAW->slave SRIO outbound window
-       ->master inbound window->master LAW->the ucode address in master's
-       NOR flash.
+       can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
+       window->master inbound window->master LAW->the ucode address in
+       master's memory space.

 
 Building the Software:
 ======================
 
 Building the Software:
 ======================


@@ -4645,7 +4735,10 @@ Over time, many people have reported problems when trying to use the
 consider minicom to be broken, and recommend not to use it. Under
 Unix, I recommend to use C-Kermit for general purpose use (and
 especially for kermit binary protocol download ("loadb" command), and
 consider minicom to be broken, and recommend not to use it. Under
 Unix, I recommend to use C-Kermit for general purpose use (and
 especially for kermit binary protocol download ("loadb" command), and

-use "cu" for S-Record download ("loads" command).
+use "cu" for S-Record download ("loads" command).  See
+http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
+for help with kermit.
+

 
 Nevertheless, if you absolutely want to use it try adding this
 configuration to your "File transfer protocols" section:
 
 Nevertheless, if you absolutely want to use it try adding this
 configuration to your "File transfer protocols" section: