ARM: uniphier: clean up board_init

[people/ms/u-boot.git] / README

diff --git a/README b/README
index 77d46d2b42e0856d92e8c3280e1172c3f608f4c3..2df0e1f8a78e66f075a6c5c0991402440f064c4f 100644 (file)
--- a/README
+++ b/README
@@ -136,7 +136,6 @@ Directory Hierarchy:
 /arch                  Architecture specific files
   /arc                 Files generic to ARC architecture
   /arm                 Files generic to ARM architecture
 /arch                  Architecture specific files
   /arc                 Files generic to ARC architecture
   /arm                 Files generic to ARM architecture

-  /avr32               Files generic to AVR32 architecture

   /m68k                        Files generic to m68k architecture
   /microblaze          Files generic to microblaze architecture
   /mips                        Files generic to MIPS architecture
   /m68k                        Files generic to m68k architecture
   /microblaze          Files generic to microblaze architecture
   /mips                        Files generic to MIPS architecture


@@ -313,6 +312,19 @@ Many of the options are named exactly as the corresponding Linux
 kernel configuration options. The intention is to make it easier to
 build a config tool - later.
 
 kernel configuration options. The intention is to make it easier to
 build a config tool - later.
 

+- ARM Platform Bus Type(CCI):
+               CoreLink Cache Coherent Interconnect (CCI) is ARM BUS which
+               provides full cache coherency between two clusters of multi-core
+               CPUs and I/O coherency for devices and I/O masters
+
+               CONFIG_SYS_FSL_HAS_CCI400
+
+               Defined For SoC that has cache coherent interconnect
+               CCN-400
+
+               CONFIG_SYS_FSL_HAS_CCN504
+
+               Defined for SoC that has cache coherent interconnect CCN-504

 
 The following options need to be configured:
 
 
 The following options need to be configured:
 


@@ -320,42 +332,11 @@ The following options need to be configured:
 
 - Board Type:  Define exactly one, e.g. CONFIG_MPC8540ADS.
 
 
 - Board Type:  Define exactly one, e.g. CONFIG_MPC8540ADS.
 

-- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
-               Define exactly one, e.g. CONFIG_ATSTK1002
-

 - Marvell Family Member
                CONFIG_SYS_MVFS         - define it if you want to enable
                                          multiple fs option at one time
                                          for marvell soc family
 
 - Marvell Family Member
                CONFIG_SYS_MVFS         - define it if you want to enable
                                          multiple fs option at one time
                                          for marvell soc family
 

-- 8xx CPU Options: (if using an MPC8xx CPU)
-               CONFIG_8xx_GCLK_FREQ    - deprecated: CPU clock if
-                                         get_gclk_freq() cannot work
-                                         e.g. if there is no 32KHz
-                                         reference PIT/RTC clock
-               CONFIG_8xx_OSCLK        - PLL input clock (either EXTCLK
-                                         or XTAL/EXTAL)
-
-- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
-               CONFIG_SYS_8xx_CPUCLK_MIN
-               CONFIG_SYS_8xx_CPUCLK_MAX
-               CONFIG_8xx_CPUCLK_DEFAULT
-                       See doc/README.MPC866
-
-               CONFIG_SYS_MEASURE_CPUCLK
-
-               Define this to measure the actual CPU clock instead
-               of relying on the correctness of the configured
-               values. Mostly useful for board bringup to make sure
-               the PLL is locked at the intended frequency. Note
-               that this requires a (stable) reference clock (32 kHz
-               RTC clock or CONFIG_SYS_8XX_XIN)
-
-               CONFIG_SYS_DELAYED_ICACHE
-
-               Define this option if you want to enable the
-               ICache only when Code runs from RAM.
-

 - 85xx CPU Options:
                CONFIG_SYS_PPC64
 
 - 85xx CPU Options:
                CONFIG_SYS_PPC64
 


@@ -436,12 +417,6 @@ The following options need to be configured:
                supported, core will start to execute uboot when wakes up.
 
 - Generic CPU options:
                supported, core will start to execute uboot when wakes up.
 
 - Generic CPU options:

-               CONFIG_SYS_GENERIC_GLOBAL_DATA
-               Defines global data is initialized in generic board board_init_f().
-               If this macro is defined, global data is created and cleared in
-               generic board board_init_f(). Without this macro, architecture/board
-               should initialize global data before calling board_init_f().
-

                CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
                Defines the endianess of the CPU. Implementation of those
                CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
 
                Defines the endianess of the CPU. Implementation of those


@@ -636,10 +611,6 @@ The following options need to be configured:
                 * Adds the "fdt" command
                 * The bootm command automatically updates the fdt
 
                 * Adds the "fdt" command
                 * The bootm command automatically updates the fdt
 

-               OF_CPU - The proper name of the cpus node (only required for
-                       MPC512X and MPC5xxx based boards).
-               OF_SOC - The proper name of the soc node (only required for
-                       MPC512X and MPC5xxx based boards).

                OF_TBCLK - The timebase frequency.
                OF_STDOUT_PATH - The path to the console device
 
                OF_TBCLK - The timebase frequency.
                OF_STDOUT_PATH - The path to the console device
 


@@ -723,29 +694,10 @@ The following options need to be configured:
                Define this variable to enable hw flow control in serial driver.
                Current user of this option is drivers/serial/nsl16550.c driver
 
                Define this variable to enable hw flow control in serial driver.
                Current user of this option is drivers/serial/nsl16550.c driver
 

-- Console Interface:
-               Depending on board, define exactly one serial port
-               (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
-               CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
-               console by defining CONFIG_8xx_CONS_NONE
-
-               Note: if CONFIG_8xx_CONS_NONE is defined, the serial
-               port routines must be defined elsewhere
-               (i.e. serial_init(), serial_getc(), ...)
-

 - Console Baudrate:
                CONFIG_BAUDRATE - in bps
                Select one of the baudrates listed in
                CONFIG_SYS_BAUDRATE_TABLE, see below.
 - Console Baudrate:
                CONFIG_BAUDRATE - in bps
                Select one of the baudrates listed in
                CONFIG_SYS_BAUDRATE_TABLE, see below.

-               CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
-
-- Console Rx buffer length
-               With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
-               the maximum receive buffer length for the SMC.
-               This option is actual only for 82xx and 8xx possible.
-               If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
-               must be defined, to setup the maximum idle timeout for
-               the SMC.

 
 - Autoboot Command:
                CONFIG_BOOTCOMMAND
 
 - Autoboot Command:
                CONFIG_BOOTCOMMAND


@@ -754,11 +706,6 @@ The following options need to be configured:
                when no character is read on the console interface
                within "Boot Delay" after reset.
 
                when no character is read on the console interface
                within "Boot Delay" after reset.
 

-               CONFIG_BOOTARGS
-               This can be used to pass arguments to the bootm
-               command. The value of CONFIG_BOOTARGS goes into the
-               environment value "bootargs".
-

                CONFIG_RAMBOOT and CONFIG_NFSBOOT
                The value of these goes into the environment as
                "ramboot" and "nfsboot" respectively, and can be used
                CONFIG_RAMBOOT and CONFIG_NFSBOOT
                The value of these goes into the environment as
                "ramboot" and "nfsboot" respectively, and can be used


@@ -811,117 +758,6 @@ The following options need to be configured:
                Select one of the baudrates listed in
                CONFIG_SYS_BAUDRATE_TABLE, see below.
 
                Select one of the baudrates listed in
                CONFIG_SYS_BAUDRATE_TABLE, see below.
 

-- Monitor Functions:
-               Monitor commands can be included or excluded
-               from the build by using the #include files
-               <config_cmd_all.h> and #undef'ing unwanted
-               commands, or adding #define's for wanted commands.
-
-               The default command configuration includes all commands
-               except those marked below with a "*".
-
-               CONFIG_CMD_AES            AES 128 CBC encrypt/decrypt
-               CONFIG_CMD_ASKENV       * ask for env variable
-               CONFIG_CMD_BDI            bdinfo
-               CONFIG_CMD_BOOTD          bootd
-               CONFIG_CMD_BOOTI        * ARM64 Linux kernel Image support
-               CONFIG_CMD_CACHE        * icache, dcache
-               CONFIG_CMD_CONSOLE        coninfo
-               CONFIG_CMD_DHCP         * DHCP support
-               CONFIG_CMD_DIAG         * Diagnostics
-               CONFIG_CMD_ECHO           echo arguments
-               CONFIG_CMD_EDITENV        edit env variable
-               CONFIG_CMD_ELF          * bootelf, bootvx
-               CONFIG_CMD_ENV_EXISTS   * check existence of env variable
-               CONFIG_CMD_EXPORTENV    * export the environment
-               CONFIG_CMD_EXT2         * ext2 command support
-               CONFIG_CMD_EXT4         * ext4 command support
-               CONFIG_CMD_FS_GENERIC   * filesystem commands (e.g. load, ls)
-                                         that work for multiple fs types
-               CONFIG_CMD_FS_UUID      * Look up a filesystem UUID
-               CONFIG_CMD_SAVEENV        saveenv
-               CONFIG_CMD_FAT          * FAT command support
-               CONFIG_CMD_FLASH          flinfo, erase, protect
-               CONFIG_CMD_FPGA           FPGA device initialization support
-               CONFIG_CMD_GO           * the 'go' command (exec code)
-               CONFIG_CMD_GREPENV      * search environment
-               CONFIG_CMD_I2C          * I2C serial bus support
-               CONFIG_CMD_IMI            iminfo
-               CONFIG_CMD_IMLS           List all images found in NOR flash
-               CONFIG_CMD_IMLS_NAND    * List all images found in NAND flash
-               CONFIG_CMD_IMPORTENV    * import an environment
-               CONFIG_CMD_INI          * import data from an ini file into the env
-               CONFIG_CMD_ITEST          Integer/string test of 2 values
-               CONFIG_CMD_LDRINFO      * ldrinfo (display Blackfin loader)
-               CONFIG_CMD_LINK_LOCAL   * link-local IP address auto-configuration
-                                         (169.254.*.*)
-               CONFIG_CMD_LOADB          loadb
-               CONFIG_CMD_LOADS          loads
-               CONFIG_CMD_MD5SUM       * print md5 message digest
-                                         (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
-               CONFIG_CMD_MEMINFO      * Display detailed memory information
-               CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,
-                                         loop, loopw
-               CONFIG_CMD_MEMTEST      * mtest
-               CONFIG_CMD_MISC           Misc functions like sleep etc
-               CONFIG_CMD_MMC          * MMC memory mapped support
-               CONFIG_CMD_MII          * MII utility commands
-               CONFIG_CMD_MTDPARTS     * MTD partition support
-               CONFIG_CMD_NAND         * NAND support
-               CONFIG_CMD_NET            bootp, tftpboot, rarpboot
-               CONFIG_CMD_NFS            NFS support
-               CONFIG_CMD_PCA953X      * PCA953x I2C gpio commands
-               CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
-               CONFIG_CMD_PCI          * pciinfo
-               CONFIG_CMD_PCMCIA               * PCMCIA support
-               CONFIG_CMD_PING         * send ICMP ECHO_REQUEST to network
-                                         host
-               CONFIG_CMD_PORTIO       * Port I/O
-               CONFIG_CMD_READ         * Read raw data from partition
-               CONFIG_CMD_REGINFO      * Register dump
-               CONFIG_CMD_RUN            run command in env variable
-               CONFIG_CMD_SANDBOX      * sb command to access sandbox features
-               CONFIG_CMD_SAVES        * save S record dump
-               CONFIG_SCSI             * SCSI Support
-               CONFIG_CMD_SDRAM        * print SDRAM configuration information
-                                         (requires CONFIG_CMD_I2C)
-               CONFIG_CMD_SETGETDCR      Support for DCR Register access
-                                         (4xx only)
-               CONFIG_CMD_SF           * Read/write/erase SPI NOR flash
-               CONFIG_CMD_SOFTSWITCH   * Soft switch setting command for BF60x
-               CONFIG_CMD_SOURCE         "source" command Support
-               CONFIG_CMD_SPI          * SPI serial bus support
-               CONFIG_CMD_TFTPSRV      * TFTP transfer in server mode
-               CONFIG_CMD_TFTPPUT      * TFTP put command (upload)
-               CONFIG_CMD_TIME         * run command and report execution time (ARM specific)
-               CONFIG_CMD_TIMER        * access to the system tick timer
-               CONFIG_CMD_USB          * USB support
-               CONFIG_CMD_CDP          * Cisco Discover Protocol support
-               CONFIG_CMD_MFSL         * Microblaze FSL support
-               CONFIG_CMD_XIMG           Load part of Multi Image
-               CONFIG_CMD_UUID         * Generate random UUID or GUID string
-
-               EXAMPLE: If you want all functions except of network
-               support you can write:
-
-               #include "config_cmd_all.h"
-               #undef CONFIG_CMD_NET
-
-       Other Commands:
-               fdt (flattened device tree) command: CONFIG_OF_LIBFDT
-
-       Note:   Don't enable the "icache" and "dcache" commands
-               (configuration option CONFIG_CMD_CACHE) unless you know
-               what you (and your U-Boot users) are doing. Data
-               cache cannot be enabled on systems like the 8xx or
-               8260 (where accesses to the IMMR region must be
-               uncached), and it cannot be disabled on all other
-               systems where we (mis-) use the data cache to hold an
-               initial stack and some data.
-
-
-               XXX - this list needs to get updated!
-

 - Removal of commands
                If no commands are needed to boot, you can disable
                CONFIG_CMDLINE to remove them. In this case, the command line
 - Removal of commands
                If no commands are needed to boot, you can disable
                CONFIG_CMDLINE to remove them. In this case, the command line


@@ -953,7 +789,7 @@ The following options need to be configured:
                binary in its image. This device tree file should be in the
                board directory and called <soc>-<board>.dts. The binary file
                is then picked up in board_init_f() and made available through
                binary in its image. This device tree file should be in the
                board directory and called <soc>-<board>.dts. The binary file
                is then picked up in board_init_f() and made available through

-               the global data structure as gd->blob.
+               the global data structure as gd->fdt_blob.

 
                CONFIG_OF_SEPARATE
                If this variable is defined, U-Boot will build a device tree
 
                CONFIG_OF_SEPARATE
                If this variable is defined, U-Boot will build a device tree


@@ -977,7 +813,7 @@ The following options need to be configured:
                CONFIG_WATCHDOG
                If this variable is defined, it enables watchdog
                support for the SoC. There must be support in the SoC
                CONFIG_WATCHDOG
                If this variable is defined, it enables watchdog
                support for the SoC. There must be support in the SoC

-               specific code for a watchdog. For the 8xx and 8260
+               specific code for a watchdog. For the 8xx

                CPUs, the SIU Watchdog feature is enabled in the SYPCR
                register.  When supported for a specific SoC is
                available, then no further board specific code should
                CPUs, the SIU Watchdog feature is enabled in the SYPCR
                register.  When supported for a specific SoC is
                available, then no further board specific code should


@@ -1005,7 +841,6 @@ The following options need to be configured:
                has to be selected, too. Define exactly one of the
                following options:
 
                has to be selected, too. Define exactly one of the
                following options:
 

-               CONFIG_RTC_MPC8xx       - use internal RTC of MPC8xx

                CONFIG_RTC_PCF8563      - use Philips PCF8563 RTC
                CONFIG_RTC_MC13XXX      - use MC13783 or MC13892 RTC
                CONFIG_RTC_MC146818     - use MC146818 RTC
                CONFIG_RTC_PCF8563      - use Philips PCF8563 RTC
                CONFIG_RTC_MC13XXX      - use MC13783 or MC13892 RTC
                CONFIG_RTC_MC146818     - use MC146818 RTC


@@ -1016,7 +851,7 @@ The following options need to be configured:
                CONFIG_RTC_DS164x       - use Dallas DS164x RTC
                CONFIG_RTC_ISL1208      - use Intersil ISL1208 RTC
                CONFIG_RTC_MAX6900      - use Maxim, Inc. MAX6900 RTC
                CONFIG_RTC_DS164x       - use Dallas DS164x RTC
                CONFIG_RTC_ISL1208      - use Intersil ISL1208 RTC
                CONFIG_RTC_MAX6900      - use Maxim, Inc. MAX6900 RTC

-               CONFIG_SYS_RTC_DS1337_NOOSC     - Turn off the OSC output for DS1337
+               CONFIG_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337

                CONFIG_SYS_RV3029_TCR   - enable trickle charger on
                                          RV3029 RTC.
 
                CONFIG_SYS_RV3029_TCR   - enable trickle charger on
                                          RV3029 RTC.
 


@@ -1065,8 +900,6 @@ The following options need to be configured:
 - Partition Labels (disklabels) Supported:
                Zero or more of the following:
                CONFIG_MAC_PARTITION   Apple's MacOS partition table.
 - Partition Labels (disklabels) Supported:
                Zero or more of the following:
                CONFIG_MAC_PARTITION   Apple's MacOS partition table.

-               CONFIG_DOS_PARTITION   MS Dos partition table, traditional on the
-                                      Intel architecture, USB sticks, etc.

                CONFIG_ISO_PARTITION   ISO partition table, used on CDROM etc.
                CONFIG_EFI_PARTITION   GPT partition table, common when EFI is the
                                       bootloader.  Note 2TB partition limit; see
                CONFIG_ISO_PARTITION   ISO partition table, used on CDROM etc.
                CONFIG_EFI_PARTITION   GPT partition table, common when EFI is the
                                       bootloader.  Note 2TB partition limit; see


@@ -1104,16 +937,11 @@ The following options need to be configured:
                        Default is 32bit.
 
 - SCSI Support:
                        Default is 32bit.
 
 - SCSI Support:

-               At the moment only there is only support for the
-               SYM53C8XX SCSI controller; define
-               CONFIG_SCSI_SYM53C8XX to enable it.
-

                CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
                CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
                CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
                maximum numbers of LUNs, SCSI ID's and target
                devices.
                CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
                CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
                CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
                maximum numbers of LUNs, SCSI ID's and target
                devices.

-               CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)

 
                The environment variable 'scsidevs' is set to the number of
                SCSI devices found during the last scan.
 
                The environment variable 'scsidevs' is set to the number of
                SCSI devices found during the last scan.


@@ -1131,10 +959,6 @@ The following options need to be configured:
                Allow generic access to the SPI bus on the Intel 8257x, for
                example with the "sspi" command.
 
                Allow generic access to the SPI bus on the Intel 8257x, for
                example with the "sspi" command.
 

-               CONFIG_CMD_E1000
-               Management command for E1000 devices.  When used on devices
-               with SPI support you can reprogram the EEPROM from U-Boot.
-

                CONFIG_EEPRO100
                Support for Intel 82557/82559/82559ER chips.
                Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
                CONFIG_EEPRO100
                Support for Intel 82557/82559/82559ER chips.
                Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM


@@ -1204,21 +1028,6 @@ The following options need to be configured:
                        control registers. This behavior won't affect the
                        correctnessof 10/100 link speed update.
 
                        control registers. This behavior won't affect the
                        correctnessof 10/100 link speed update.
 

-               CONFIG_SMC911X
-               Support for SMSC's LAN911x and LAN921x chips
-
-                       CONFIG_SMC911X_BASE
-                       Define this to hold the physical address
-                       of the device (I/O space)
-
-                       CONFIG_SMC911X_32_BIT
-                       Define this if data bus is 32 bits
-
-                       CONFIG_SMC911X_16_BIT
-                       Define this if data bus is 16 bits. If your processor
-                       automatically converts one 32 bit word to two 16 bit
-                       words you may also try CONFIG_SMC911X_32_BIT.
-

                CONFIG_SH_ETHER
                Support for Renesas on-chip Ethernet controller
 
                CONFIG_SH_ETHER
                Support for Renesas on-chip Ethernet controller
 


@@ -1269,11 +1078,6 @@ The following options need to be configured:
                        to. Contemporary x86 systems usually map it at
                        0xfed40000.
 
                        to. Contemporary x86 systems usually map it at
                        0xfed40000.
 

-               CONFIG_CMD_TPM
-               Add tpm monitor functions.
-               Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
-               provides monitor access to authorized functions.
-

                CONFIG_TPM
                Define this to enable the TPM support library which provides
                functional interfaces to some TPM commands.
                CONFIG_TPM
                Define this to enable the TPM support library which provides
                functional interfaces to some TPM commands.


@@ -1285,7 +1089,7 @@ The following options need to be configured:
 
 - USB Support:
                At the moment only the UHCI host controller is
 
 - USB Support:
                At the moment only the UHCI host controller is

-               supported (PIP405, MIP405, MPC5200); define
+               supported (PIP405, MIP405); define

                CONFIG_USB_UHCI to enable it.
                define CONFIG_USB_KEYBOARD to enable the USB Keyboard
                and define CONFIG_USB_STORAGE to enable the USB
                CONFIG_USB_UHCI to enable it.
                define CONFIG_USB_KEYBOARD to enable the USB Keyboard
                and define CONFIG_USB_STORAGE to enable the USB


@@ -1293,19 +1097,6 @@ The following options need to be configured:
                Note:
                Supported are USB Keyboards and USB Floppy drives
                (TEAC FD-05PUB).
                Note:
                Supported are USB Keyboards and USB Floppy drives
                (TEAC FD-05PUB).

-               MPC5200 USB requires additional defines:
-                       CONFIG_USB_CLOCK
-                               for 528 MHz Clock: 0x0001bbbb
-                       CONFIG_PSC3_USB
-                               for USB on PSC3
-                       CONFIG_USB_CONFIG
-                               for differential drivers: 0x00001000
-                               for single ended drivers: 0x00005000
-                               for differential drivers on PSC3: 0x00000100
-                               for single ended drivers on PSC3: 0x00004100
-                       CONFIG_SYS_USB_EVENT_POLL
-                               May be defined to allow interrupt polling
-                               instead of using asynchronous interrupts

 
                CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
                txfilltuning field in the EHCI controller on reset.
 
                CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
                txfilltuning field in the EHCI controller on reset.


@@ -1348,11 +1139,6 @@ The following options need to be configured:
                        Define this if you want stdin, stdout &/or stderr to
                        be set to usbtty.
 
                        Define this if you want stdin, stdout &/or stderr to
                        be set to usbtty.
 

-                       mpc8xx:
-                               CONFIG_SYS_USB_EXTC_CLK 0xBLAH
-                               Derive USB clock from external clock "blah"
-                               - CONFIG_SYS_USB_EXTC_CLK 0x02
-

                If you have a USB-IF assigned VendorID then you may wish to
                define your own vendor specific values either in BoardName.h
                or directly in usbd_vendor_info.h. If you don't define
                If you have a USB-IF assigned VendorID then you may wish to
                define your own vendor specific values either in BoardName.h
                or directly in usbd_vendor_info.h. If you don't define


@@ -1419,12 +1205,6 @@ The following options need to be configured:
                CONFIG_USB_FUNCTION_DFU
                This enables the USB portion of the DFU USB class
 
                CONFIG_USB_FUNCTION_DFU
                This enables the USB portion of the DFU USB class
 

-               CONFIG_CMD_DFU
-               This enables the command "dfu" which is used to have
-               U-Boot create a DFU class device via USB.  This command
-               requires that the "dfu_alt_info" environment variable be
-               set and define the alt settings to expose to the host.
-

                CONFIG_DFU_MMC
                This enables support for exposing (e)MMC devices via DFU.
 
                CONFIG_DFU_MMC
                This enables support for exposing (e)MMC devices via DFU.
 


@@ -1460,57 +1240,6 @@ The following options need to be configured:
                entering dfuMANIFEST state. Host waits this timeout, before
                sending again an USB request to the device.
 
                entering dfuMANIFEST state. Host waits this timeout, before
                sending again an USB request to the device.
 

-- USB Device Android Fastboot support:
-               CONFIG_USB_FUNCTION_FASTBOOT
-               This enables the USB part of the fastboot gadget
-
-               CONFIG_CMD_FASTBOOT
-               This enables the command "fastboot" which enables the Android
-               fastboot mode for the platform's USB device. Fastboot is a USB
-               protocol for downloading images, flashing and device control
-               used on Android devices.
-               See doc/README.android-fastboot for more information.
-
-               CONFIG_ANDROID_BOOT_IMAGE
-               This enables support for booting images which use the Android
-               image format header.
-
-               CONFIG_FASTBOOT_BUF_ADDR
-               The fastboot protocol requires a large memory buffer for
-               downloads. Define this to the starting RAM address to use for
-               downloaded images.
-
-               CONFIG_FASTBOOT_BUF_SIZE
-               The fastboot protocol requires a large memory buffer for
-               downloads. This buffer should be as large as possible for a
-               platform. Define this to the size available RAM for fastboot.
-
-               CONFIG_FASTBOOT_FLASH
-               The fastboot protocol includes a "flash" command for writing
-               the downloaded image to a non-volatile storage device. Define
-               this to enable the "fastboot flash" command.
-
-               CONFIG_FASTBOOT_FLASH_MMC_DEV
-               The fastboot "flash" command requires additional information
-               regarding the non-volatile storage device. Define this to
-               the eMMC device that fastboot should use to store the image.
-
-               CONFIG_FASTBOOT_GPT_NAME
-               The fastboot "flash" command supports writing the downloaded
-               image to the Protective MBR and the Primary GUID Partition
-               Table. (Additionally, this downloaded image is post-processed
-               to generate and write the Backup GUID Partition Table.)
-               This occurs when the specified "partition name" on the
-               "fastboot flash" command line matches this value.
-               The default is "gpt" if undefined.
-
-               CONFIG_FASTBOOT_MBR_NAME
-               The fastboot "flash" command supports writing the downloaded
-               image to DOS MBR.
-               This occurs when the "partition name" specified on the
-               "fastboot flash" command line matches this value.
-               If not defined the default value "mbr" is used.
-

 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND
                Define these for a default partition on a NAND device
 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND
                Define these for a default partition on a NAND device


@@ -1519,21 +1248,6 @@ The following options need to be configured:
                CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
                Define these for a default partition on a NOR device
 
                CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
                Define these for a default partition on a NOR device
 

-- FAT(File Allocation Table) filesystem write function support:
-               CONFIG_FAT_WRITE
-
-               Define this to enable support for saving memory data as a
-               file in FAT formatted partition.
-
-               This will also enable the command "fatwrite" enabling the
-               user to write files to FAT.
-
-- FAT(File Allocation Table) filesystem cluster size:
-               CONFIG_FS_FAT_MAX_CLUSTSIZE
-
-               Define the max cluster size for fat operations else
-               a default value of 65536 will be defined.
-

 - Keyboard Support:
                See Kconfig help for available keyboard drivers.
 
 - Keyboard Support:
                See Kconfig help for available keyboard drivers.
 


@@ -1720,11 +1434,6 @@ The following options need to be configured:
                the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
                be at least 4MB.
 
                the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
                be at least 4MB.
 

-               CONFIG_LZO
-
-               If this option is set, support for LZO compressed images
-               is included.
-

 - MII/PHY support:
                CONFIG_PHY_ADDR
 
 - MII/PHY support:
                CONFIG_PHY_ADDR
 


@@ -1734,11 +1443,6 @@ The following options need to be configured:
 
                The clock frequency of the MII bus
 
 
                The clock frequency of the MII bus
 

-               CONFIG_PHY_GIGE
-
-               If this option is set, support for speed/duplex
-               detection of gigabit PHY is included.
-

                CONFIG_PHY_RESET_DELAY
 
                Some PHY like Intel LXT971A need extra delay after
                CONFIG_PHY_RESET_DELAY
 
                Some PHY like Intel LXT971A need extra delay after


@@ -1967,12 +1671,6 @@ The following options need to be configured:
                In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
                with a list of GPIO LEDs that have inverted polarity.
 
                In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
                with a list of GPIO LEDs that have inverted polarity.
 

-- CAN Support: CONFIG_CAN_DRIVER
-
-               Defining CONFIG_CAN_DRIVER enables CAN driver support
-               on those systems that support this (optional)
-               feature, like the TQM8xxL modules.
-

 - I2C Support: CONFIG_SYS_I2C
 
                This enable the NEW i2c subsystem, and will allow you to use
 - I2C Support: CONFIG_SYS_I2C
 
                This enable the NEW i2c subsystem, and will allow you to use


@@ -2171,12 +1869,6 @@ The following options need to be configured:
 
                eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |=  PB_SCL)
 
 
                eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |=  PB_SCL)
 

-               I2C_PORT
-
-               (Only for MPC8260 CPU). The I/O port to use (the code
-               assumes both bits are on the same port). Valid values
-               are 0..3 for ports A..D.
-

                I2C_ACTIVE
 
                The code necessary to make the I2C data line active
                I2C_ACTIVE
 
                The code necessary to make the I2C data line active


@@ -2463,9 +2155,9 @@ The following options need to be configured:
                following board configurations are known to be
                "pRAM-clean":
 
                following board configurations are known to be
                "pRAM-clean":
 

-                       IVMS8, IVML24, SPD8xx, TQM8xxL,
+                       IVMS8, IVML24, SPD8xx,

                        HERMES, IP860, RPXlite, LWMON,
                        HERMES, IP860, RPXlite, LWMON,

-                       FLAGADM, TQM8260
+                       FLAGADM

 
 - Access to physical memory region (> 4GB)
                Some basic support is provided for operations on memory not
 
 - Access to physical memory region (> 4GB)
                Some basic support is provided for operations on memory not


@@ -2605,20 +2297,8 @@ The following options need to be configured:
                this is instead controlled by the value of
                /config/load-environment.
 
                this is instead controlled by the value of
                /config/load-environment.
 

-- DataFlash Support:
-               CONFIG_HAS_DATAFLASH
-
-               Defining this option enables DataFlash features and
-               allows to read/write in Dataflash via the standard
-               commands cp, md...
-

 - Serial Flash support
 - Serial Flash support

-               CONFIG_CMD_SF
-
-               Defining this option enables SPI flash commands
-               'sf probe/read/write/erase/update'.
-
-               Usage requires an initial 'probe' to define the serial
+               Usage requires an initial 'sf probe' to define the serial

                flash parameters, followed by read/write/erase/update
                commands.
 
                flash parameters, followed by read/write/erase/update
                commands.
 


@@ -2631,18 +2311,6 @@ The following options need to be configured:
                CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
                CONFIG_SF_DEFAULT_SPEED         in Hz
 
                CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
                CONFIG_SF_DEFAULT_SPEED         in Hz
 

-               CONFIG_CMD_SF_TEST
-
-               Define this option to include a destructive SPI flash
-               test ('sf test').
-
-               CONFIG_SF_DUAL_FLASH            Dual flash memories
-
-               Define this option to use dual flash support where two flash
-               memories can be connected with a given cs line.
-               Currently Xilinx Zynq qspi supports these type of connections.
-
-- SystemACE Support:

                CONFIG_SYSTEMACE
 
                Adding this option adds support for Xilinx SystemACE
                CONFIG_SYSTEMACE
 
                Adding this option adds support for Xilinx SystemACE


@@ -2694,6 +2362,13 @@ The following options need to be configured:
                        CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
                                                    the bootcounter.
                        CONFIG_BOOTCOUNT_ALEN = address len
                        CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
                                                    the bootcounter.
                        CONFIG_BOOTCOUNT_ALEN = address len

+               CONFIG_BOOTCOUNT_EXT
+               enable support for the bootcounter in EXT filesystem
+                       CONFIG_SYS_BOOTCOUNT_ADDR = RAM address used for read
+                                                    and write.
+                       CONFIG_SYS_BOOTCOUNT_EXT_INTERFACE = interface
+                       CONFIG_SYS_BOOTCOUNT_EXT_DEVPART = device and part
+                       CONFIG_SYS_BOOTCOUNT_EXT_NAME = filename

 
 - Show boot progress:
                CONFIG_SHOW_BOOT_PROGRESS
 
 - Show boot progress:
                CONFIG_SHOW_BOOT_PROGRESS


@@ -2914,13 +2589,6 @@ FIT uImage format:
                kernel. Needed for UBI support.
 
 - UBI support
                kernel. Needed for UBI support.
 
 - UBI support

-               CONFIG_CMD_UBI
-
-               Adds commands for interacting with MTD partitions formatted
-               with the UBI flash translation layer
-
-               Requires also defining CONFIG_RBTREE
-

                CONFIG_UBI_SILENCE_MSG
 
                Make the verbose messages from UBI stop printing.  This leaves
                CONFIG_UBI_SILENCE_MSG
 
                Make the verbose messages from UBI stop printing.  This leaves


@@ -2989,13 +2657,6 @@ FIT uImage format:
                default: 0
 
 - UBIFS support
                default: 0
 
 - UBIFS support

-               CONFIG_CMD_UBIFS
-
-               Adds commands for interacting with UBI volumes formatted as
-               UBIFS.  UBIFS is read-only in u-boot.
-
-               Requires UBI support as well as CONFIG_LZO
-

                CONFIG_UBIFS_SILENCE_MSG
 
                Make the verbose messages from UBIFS stop printing.  This leaves
                CONFIG_UBIFS_SILENCE_MSG
 
                Make the verbose messages from UBIFS stop printing.  This leaves


@@ -3172,10 +2833,6 @@ FIT uImage format:
                Define this if you need to first read the OOB and then the
                data. This is used, for example, on davinci platforms.
 
                Define this if you need to first read the OOB and then the
                data. This is used, for example, on davinci platforms.
 

-               CONFIG_SPL_OMAP3_ID_NAND
-               Support for an OMAP3-specific set of functions to return the
-               ID and MFR of the first attached NAND chip, if present.
-

                CONFIG_SPL_RAM_DEVICE
                Support for running image already present in ram, in SPL binary
 
                CONFIG_SPL_RAM_DEVICE
                Support for running image already present in ram, in SPL binary
 


@@ -3550,90 +3207,6 @@ following configurations:
        Builds up envcrc with the target environment so that external utils
        may easily extract it and embed it in final U-Boot images.
 
        Builds up envcrc with the target environment so that external utils
        may easily extract it and embed it in final U-Boot images.
 

-- CONFIG_ENV_IS_IN_FLASH:
-
-       Define this if the environment is in flash memory.
-
-       a) The environment occupies one whole flash sector, which is
-          "embedded" in the text segment with the U-Boot code. This
-          happens usually with "bottom boot sector" or "top boot
-          sector" type flash chips, which have several smaller
-          sectors at the start or the end. For instance, such a
-          layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
-          such a case you would place the environment in one of the
-          4 kB sectors - with U-Boot code before and after it. With
-          "top boot sector" type flash chips, you would put the
-          environment in one of the last sectors, leaving a gap
-          between U-Boot and the environment.
-
-       - CONFIG_ENV_OFFSET:
-
-          Offset of environment data (variable area) to the
-          beginning of flash memory; for instance, with bottom boot
-          type flash chips the second sector can be used: the offset
-          for this sector is given here.
-
-          CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
-
-       - CONFIG_ENV_ADDR:
-
-          This is just another way to specify the start address of
-          the flash sector containing the environment (instead of
-          CONFIG_ENV_OFFSET).
-
-       - CONFIG_ENV_SECT_SIZE:
-
-          Size of the sector containing the environment.
-
-
-       b) Sometimes flash chips have few, equal sized, BIG sectors.
-          In such a case you don't want to spend a whole sector for
-          the environment.
-
-       - CONFIG_ENV_SIZE:
-
-          If you use this in combination with CONFIG_ENV_IS_IN_FLASH
-          and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
-          of this flash sector for the environment. This saves
-          memory for the RAM copy of the environment.
-
-          It may also save flash memory if you decide to use this
-          when your environment is "embedded" within U-Boot code,
-          since then the remainder of the flash sector could be used
-          for U-Boot code. It should be pointed out that this is
-          STRONGLY DISCOURAGED from a robustness point of view:
-          updating the environment in flash makes it always
-          necessary to erase the WHOLE sector. If something goes
-          wrong before the contents has been restored from a copy in
-          RAM, your target system will be dead.
-
-       - CONFIG_ENV_ADDR_REDUND
-         CONFIG_ENV_SIZE_REDUND
-
-          These settings describe a second storage area used to hold
-          a redundant copy of the environment data, so that there is
-          a valid backup copy in case there is a power failure during
-          a "saveenv" operation.
-
-BE CAREFUL! Any changes to the flash layout, and some changes to the
-source code will make it necessary to adapt <board>/u-boot.lds*
-accordingly!
-
-
-- CONFIG_ENV_IS_IN_NVRAM:
-
-       Define this if you have some non-volatile memory device
-       (NVRAM, battery buffered SRAM) which you want to use for the
-       environment.
-
-       - CONFIG_ENV_ADDR:
-       - CONFIG_ENV_SIZE:
-
-         These two #defines are used to determine the memory area you
-         want to use for environment. It is assumed that this memory
-         can just be read and written to, without any special
-         provision.
-

 BE CAREFUL! The first access to the environment happens quite early
 in U-Boot initialization (when we try to get the setting of for the
 console baudrate). You *MUST* have mapped your NVRAM area then, or
 BE CAREFUL! The first access to the environment happens quite early
 in U-Boot initialization (when we try to get the setting of for the
 console baudrate). You *MUST* have mapped your NVRAM area then, or


@@ -3644,298 +3217,20 @@ environment in RAM: we could work on NVRAM directly, but we want to
 keep settings there always unmodified except somebody uses "saveenv"
 to save the current settings.
 
 keep settings there always unmodified except somebody uses "saveenv"
 to save the current settings.
 

-
-- CONFIG_ENV_IS_IN_EEPROM:
-
-       Use this if you have an EEPROM or similar serial access
-       device and a driver for it.
-
-       - CONFIG_ENV_OFFSET:
-       - CONFIG_ENV_SIZE:
-
-         These two #defines specify the offset and size of the
-         environment area within the total memory of your EEPROM.
-
-       - CONFIG_SYS_I2C_EEPROM_ADDR:
-         If defined, specified the chip address of the EEPROM device.
-         The default address is zero.
-
-       - CONFIG_SYS_I2C_EEPROM_BUS:
-         If defined, specified the i2c bus of the EEPROM device.
-
-       - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
-         If defined, the number of bits used to address bytes in a
-         single page in the EEPROM device.  A 64 byte page, for example
-         would require six bits.
-
-       - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
-         If defined, the number of milliseconds to delay between
-         page writes.  The default is zero milliseconds.
-
-       - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
-         The length in bytes of the EEPROM memory array address.  Note
-         that this is NOT the chip address length!
-
-       - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
-         EEPROM chips that implement "address overflow" are ones
-         like Catalyst 24WC04/08/16 which has 9/10/11 bits of
-         address and the extra bits end up in the "chip address" bit
-         slots. This makes a 24WC08 (1Kbyte) chip look like four 256
-         byte chips.
-
-         Note that we consider the length of the address field to
-         still be one byte because the extra address bits are hidden
-         in the chip address.
-
-       - CONFIG_SYS_EEPROM_SIZE:
-         The size in bytes of the EEPROM device.
-
-       - CONFIG_ENV_EEPROM_IS_ON_I2C
-         define this, if you have I2C and SPI activated, and your
-         EEPROM, which holds the environment, is on the I2C bus.
-
-       - CONFIG_I2C_ENV_EEPROM_BUS
-         if you have an Environment on an EEPROM reached over
-         I2C muxes, you can define here, how to reach this
-         EEPROM. For example:
-
-         #define CONFIG_I2C_ENV_EEPROM_BUS       1
-
-         EEPROM which holds the environment, is reached over
-         a pca9547 i2c mux with address 0x70, channel 3.
-
-- CONFIG_ENV_IS_IN_DATAFLASH:
-
-       Define this if you have a DataFlash memory device which you
-       want to use for the environment.
-
-       - CONFIG_ENV_OFFSET:
-       - CONFIG_ENV_ADDR:
-       - CONFIG_ENV_SIZE:
-
-         These three #defines specify the offset and size of the
-         environment area within the total memory of your DataFlash placed
-         at the specified address.
-
-- CONFIG_ENV_IS_IN_SPI_FLASH:
-
-       Define this if you have a SPI Flash memory device which you
-       want to use for the environment.
-
-       - CONFIG_ENV_OFFSET:
-       - CONFIG_ENV_SIZE:
-
-         These two #defines specify the offset and size of the
-         environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
-         aligned to an erase sector boundary.
-
-       - CONFIG_ENV_SECT_SIZE:
-
-         Define the SPI flash's sector size.
-
-       - CONFIG_ENV_OFFSET_REDUND (optional):
-
-         This setting describes a second storage area of CONFIG_ENV_SIZE
-         size used to hold a redundant copy of the environment data, so
-         that there is a valid backup copy in case there is a power failure
-         during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
-         aligned to an erase sector boundary.
-
-       - CONFIG_ENV_SPI_BUS (optional):
-       - CONFIG_ENV_SPI_CS (optional):
-
-         Define the SPI bus and chip select. If not defined they will be 0.
-
-       - CONFIG_ENV_SPI_MAX_HZ (optional):
-
-         Define the SPI max work clock. If not defined then use 1MHz.
-
-       - CONFIG_ENV_SPI_MODE (optional):
-
-         Define the SPI work mode. If not defined then use SPI_MODE_3.
-
-- CONFIG_ENV_IS_IN_REMOTE:
-
-       Define this if you have a remote memory space which you
-       want to use for the local device's environment.
-
-       - CONFIG_ENV_ADDR:
-       - CONFIG_ENV_SIZE:
-
-         These two #defines specify the address and size of the
-         environment area within the remote memory space. The
-         local device can get the environment from remote memory
-         space by SRIO or PCIE links.
-

 BE CAREFUL! For some special cases, the local device can not use
 "saveenv" command. For example, the local device will get the
 environment stored in a remote NOR flash by SRIO or PCIE link,
 but it can not erase, write this NOR flash by SRIO or PCIE interface.
 
 BE CAREFUL! For some special cases, the local device can not use
 "saveenv" command. For example, the local device will get the
 environment stored in a remote NOR flash by SRIO or PCIE link,
 but it can not erase, write this NOR flash by SRIO or PCIE interface.
 

-- CONFIG_ENV_IS_IN_NAND:
-
-       Define this if you have a NAND device which you want to use
-       for the environment.
-
-       - CONFIG_ENV_OFFSET:
-       - CONFIG_ENV_SIZE:
-
-         These two #defines specify the offset and size of the environment
-         area within the first NAND device.  CONFIG_ENV_OFFSET must be
-         aligned to an erase block boundary.
-
-       - CONFIG_ENV_OFFSET_REDUND (optional):
-
-         This setting describes a second storage area of CONFIG_ENV_SIZE
-         size used to hold a redundant copy of the environment data, so
-         that there is a valid backup copy in case there is a power failure
-         during a "saveenv" operation.  CONFIG_ENV_OFFSET_REDUND must be
-         aligned to an erase block boundary.
-
-       - CONFIG_ENV_RANGE (optional):
-
-         Specifies the length of the region in which the environment
-         can be written.  This should be a multiple of the NAND device's
-         block size.  Specifying a range with more erase blocks than
-         are needed to hold CONFIG_ENV_SIZE allows bad blocks within
-         the range to be avoided.
-
-       - CONFIG_ENV_OFFSET_OOB (optional):
-
-         Enables support for dynamically retrieving the offset of the
-         environment from block zero's out-of-band data.  The
-         "nand env.oob" command can be used to record this offset.
-         Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
-         using CONFIG_ENV_OFFSET_OOB.
-

 - CONFIG_NAND_ENV_DST
 
        Defines address in RAM to which the nand_spl code should copy the
        environment. If redundant environment is used, it will be copied to
        CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
 
 - CONFIG_NAND_ENV_DST
 
        Defines address in RAM to which the nand_spl code should copy the
        environment. If redundant environment is used, it will be copied to
        CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
 

-- CONFIG_ENV_IS_IN_UBI:
-
-       Define this if you have an UBI volume that you want to use for the
-       environment.  This has the benefit of wear-leveling the environment
-       accesses, which is important on NAND.
-
-       - CONFIG_ENV_UBI_PART:
-
-         Define this to a string that is the mtd partition containing the UBI.
-
-       - CONFIG_ENV_UBI_VOLUME:
-
-         Define this to the name of the volume that you want to store the
-         environment in.
-
-       - CONFIG_ENV_UBI_VOLUME_REDUND:
-
-         Define this to the name of another volume to store a second copy of
-         the environment in.  This will enable redundant environments in UBI.
-         It is assumed that both volumes are in the same MTD partition.
-
-       - CONFIG_UBI_SILENCE_MSG
-       - CONFIG_UBIFS_SILENCE_MSG
-
-         You will probably want to define these to avoid a really noisy system
-         when storing the env in UBI.
-
-- CONFIG_ENV_IS_IN_FAT:
-       Define this if you want to use the FAT file system for the environment.
-
-       - FAT_ENV_INTERFACE:
-
-         Define this to a string that is the name of the block device.
-
-       - FAT_ENV_DEVICE_AND_PART:
-
-         Define this to a string to specify the partition of the device. It can
-         be as following:
-
-           "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
-               - "D:P": device D partition P. Error occurs if device D has no
-                        partition table.
-               - "D:0": device D.
-               - "D" or "D:": device D partition 1 if device D has partition
-                              table, or the whole device D if has no partition
-                              table.
-               - "D:auto": first partition in device D with bootable flag set.
-                           If none, first valid partition in device D. If no
-                           partition table then means device D.
-
-       - FAT_ENV_FILE:
-
-         It's a string of the FAT file name. This file use to store the
-         environment.
-
-       - CONFIG_FAT_WRITE:
-         This should be defined. Otherwise it cannot save the environment file.
-
-- CONFIG_ENV_IS_IN_MMC:
-
-       Define this if you have an MMC device which you want to use for the
-       environment.
-
-       - CONFIG_SYS_MMC_ENV_DEV:
-
-         Specifies which MMC device the environment is stored in.
-
-       - CONFIG_SYS_MMC_ENV_PART (optional):
-
-         Specifies which MMC partition the environment is stored in. If not
-         set, defaults to partition 0, the user area. Common values might be
-         1 (first MMC boot partition), 2 (second MMC boot partition).
-
-       - CONFIG_ENV_OFFSET:
-       - CONFIG_ENV_SIZE:
-
-         These two #defines specify the offset and size of the environment
-         area within the specified MMC device.
-
-         If offset is positive (the usual case), it is treated as relative to
-         the start of the MMC partition. If offset is negative, it is treated
-         as relative to the end of the MMC partition. This can be useful if
-         your board may be fitted with different MMC devices, which have
-         different sizes for the MMC partitions, and you always want the
-         environment placed at the very end of the partition, to leave the
-         maximum possible space before it, to store other data.
-
-         These two values are in units of bytes, but must be aligned to an
-         MMC sector boundary.
-
-       - CONFIG_ENV_OFFSET_REDUND (optional):
-
-         Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
-         hold a redundant copy of the environment data. This provides a
-         valid backup copy in case the other copy is corrupted, e.g. due
-         to a power failure during a "saveenv" operation.
-
-         This value may also be positive or negative; this is handled in the
-         same way as CONFIG_ENV_OFFSET.
-
-         This value is also in units of bytes, but must also be aligned to
-         an MMC sector boundary.
-
-       - CONFIG_ENV_SIZE_REDUND (optional):
-
-         This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
-         set. If this value is set, it must be set to the same value as
-         CONFIG_ENV_SIZE.
-
-- CONFIG_SYS_SPI_INIT_OFFSET
-
-       Defines offset to the initial SPI buffer area in DPRAM. The
-       area is used at an early stage (ROM part) if the environment
-       is configured to reside in the SPI EEPROM: We need a 520 byte
-       scratch DPRAM area. It is used between the two initialization
-       calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
-       to be a good choice since it makes it far enough from the
-       start of the data area as well as from the stack pointer.
-

 Please note that the environment is read-only until the monitor
 has been relocated to RAM and a RAM copy of the environment has been
 Please note that the environment is read-only until the monitor
 has been relocated to RAM and a RAM copy of the environment has been

-created; also, when using EEPROM you will have to use getenv_f()
+created; also, when using EEPROM you will have to use env_get_f()

 until then to read environment variables.
 
 The environment is protected by a CRC32 checksum. Before the monitor
 until then to read environment variables.
 
 The environment is protected by a CRC32 checksum. Before the monitor


@@ -3986,13 +3281,6 @@ Low Level (hardware related) configuration options:
 - CONFIG_SYS_CACHELINE_SIZE:
                Cache Line Size of the CPU.
 
 - CONFIG_SYS_CACHELINE_SIZE:
                Cache Line Size of the CPU.
 

-- CONFIG_SYS_DEFAULT_IMMR:
-               Default address of the IMMR after system reset.
-
-               Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
-               and RPXsuper) to be able to adjust the position of
-               the IMMR register after a reset.
-

 - CONFIG_SYS_CCSRBAR_DEFAULT:
                Default (power-on reset) physical address of CCSR on Freescale
                PowerPC SOCs.
 - CONFIG_SYS_CCSRBAR_DEFAULT:
                Default (power-on reset) physical address of CCSR on Freescale
                PowerPC SOCs.


@@ -4001,9 +3289,6 @@ Low Level (hardware related) configuration options:
                Virtual address of CCSR.  On a 32-bit build, this is typically
                the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
 
                Virtual address of CCSR.  On a 32-bit build, this is typically
                the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
 

-               CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
-               for cross-platform code that uses that macro instead.
-

 - CONFIG_SYS_CCSRBAR_PHYS:
                Physical address of CCSR.  CCSR can be relocated to a new
                physical address, if desired.  In this case, this macro should
 - CONFIG_SYS_CCSRBAR_PHYS:
                Physical address of CCSR.  CCSR can be relocated to a new
                physical address, if desired.  In this case, this macro should


@@ -4066,7 +3351,7 @@ Low Level (hardware related) configuration options:
 
 - CONFIG_SYS_IMMR:     Physical address of the Internal Memory.
                DO NOT CHANGE unless you know exactly what you're
 
 - CONFIG_SYS_IMMR:     Physical address of the Internal Memory.
                DO NOT CHANGE unless you know exactly what you're

-               doing! (11-4) [MPC8xx/82xx systems only]
+               doing! (11-4) [MPC8xx systems only]

 
 - CONFIG_SYS_INIT_RAM_ADDR:
 
 
 - CONFIG_SYS_INIT_RAM_ADDR:
 


@@ -4079,9 +3364,7 @@ Low Level (hardware related) configuration options:
                sequences.
 
                U-Boot uses the following memory types:
                sequences.
 
                U-Boot uses the following memory types:

-               - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
-               - MPC824X: data cache
-               - PPC4xx:  data cache
+               - MPC8xx: IMMR (internal memory of the CPU)

 
 - CONFIG_SYS_GBL_DATA_OFFSET:
 
 
 - CONFIG_SYS_GBL_DATA_OFFSET:
 


@@ -4101,16 +3384,6 @@ Low Level (hardware related) configuration options:
                point to an otherwise UNUSED address space between
                the top of RAM and the start of the PCI space.
 
                point to an otherwise UNUSED address space between
                the top of RAM and the start of the PCI space.
 

-- CONFIG_SYS_SIUMCR:   SIU Module Configuration (11-6)
-
-- CONFIG_SYS_SYPCR:    System Protection Control (11-9)
-
-- CONFIG_SYS_TBSCR:    Time Base Status and Control (11-26)
-
-- CONFIG_SYS_PISCR:    Periodic Interrupt Status and Control (11-31)
-
-- CONFIG_SYS_PLPRCR:   PLL, Low-Power, and Reset Control Register (15-30)
-

 - CONFIG_SYS_SCCR:     System Clock and reset Control Register (15-27)
 
 - CONFIG_SYS_OR_TIMING_SDRAM:
 - CONFIG_SYS_SCCR:     System Clock and reset Control Register (15-27)
 
 - CONFIG_SYS_OR_TIMING_SDRAM:


@@ -4119,8 +3392,6 @@ Low Level (hardware related) configuration options:
 - CONFIG_SYS_MAMR_PTA:
                periodic timer for refresh
 
 - CONFIG_SYS_MAMR_PTA:
                periodic timer for refresh
 

-- CONFIG_SYS_DER:      Debug Event Register (37-47)
-

 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
   CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
   CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
   CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
   CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,


@@ -4132,43 +3403,6 @@ Low Level (hardware related) configuration options:
   CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
                Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
 
   CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
                Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
 

-- CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
-  CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
-               Machine Mode Register and Memory Periodic Timer
-               Prescaler definitions (SDRAM timing)
-
-- CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
-               enable I2C microcode relocation patch (MPC8xx);
-               define relocation offset in DPRAM [DSP2]
-
-- CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
-               enable SMC microcode relocation patch (MPC8xx);
-               define relocation offset in DPRAM [SMC1]
-
-- CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
-               enable SPI microcode relocation patch (MPC8xx);
-               define relocation offset in DPRAM [SCC4]
-
-- CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
-               Offset of the bootmode word in DPRAM used by post
-               (Power On Self Tests). This definition overrides
-               #define'd default value in commproc.h resp.
-               cpm_8260.h.
-
-- CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
-  CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
-  CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
-  CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
-  CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
-  CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
-  CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
-  CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
-               Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
-
-- CONFIG_PCI_DISABLE_PCIE:
-               Disable PCI-Express on systems where it is supported but not
-               required.
-

 - CONFIG_PCI_ENUM_ONLY
                Only scan through and get the devices on the buses.
                Don't do any setup work, presumably because someone or
 - CONFIG_PCI_ENUM_ONLY
                Only scan through and get the devices on the buses.
                Don't do any setup work, presumably because someone or


@@ -4243,21 +3477,6 @@ Low Level (hardware related) configuration options:
                Only for 83xx systems. If specified, then DDR should
                be configured using CS0 and CS1 instead of CS2 and CS3.
 
                Only for 83xx systems. If specified, then DDR should
                be configured using CS0 and CS1 instead of CS2 and CS3.
 

-- CONFIG_ETHER_ON_FEC[12]
-               Define to enable FEC[12] on a 8xx series processor.
-
-- CONFIG_FEC[12]_PHY
-               Define to the hardcoded PHY address which corresponds
-               to the given FEC; i. e.
-                       #define CONFIG_FEC1_PHY 4
-               means that the PHY with address 4 is connected to FEC1
-
-               When set to -1, means to probe for first available.
-
-- CONFIG_FEC[12]_PHY_NORXERR
-               The PHY does not have a RXERR line (RMII only).
-               (so program the FEC to ignore it).
-

 - CONFIG_RMII
                Enable RMII mode for all FECs.
                Note that this is a global option, we can't
 - CONFIG_RMII
                Enable RMII mode for all FECs.
                Note that this is a global option, we can't


@@ -4275,7 +3494,7 @@ Low Level (hardware related) configuration options:
 
 - CONFIG_LOOPW
                Add the "loopw" memory command. This only takes effect if
 
 - CONFIG_LOOPW
                Add the "loopw" memory command. This only takes effect if

-               the memory commands are activated globally (CONFIG_CMD_MEM).
+               the memory commands are activated globally (CONFIG_CMD_MEMORY).

 
 - CONFIG_MX_CYCLIC
                Add the "mdc" and "mwc" memory commands. These are cyclic
 
 - CONFIG_MX_CYCLIC
                Add the "mdc" and "mwc" memory commands. These are cyclic


@@ -4289,7 +3508,7 @@ Low Level (hardware related) configuration options:
                This command will write 12345678 to address 100 all 10 ms.
 
                This only takes effect if the memory commands are activated
                This command will write 12345678 to address 100 all 10 ms.
 
                This only takes effect if the memory commands are activated

-               globally (CONFIG_CMD_MEM).
+               globally (CONFIG_CMD_MEMORY).

 
 - CONFIG_SKIP_LOWLEVEL_INIT
                [ARM, NDS32, MIPS only] If this variable is defined, then certain
 
 - CONFIG_SKIP_LOWLEVEL_INIT
                [ARM, NDS32, MIPS only] If this variable is defined, then certain


@@ -5007,9 +4226,9 @@ details; basically, the header defines the following image properties:
   LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
   Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
   INTEGRITY).
   LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
   Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
   INTEGRITY).

-* Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
+* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,

   IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
   IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;

-  Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
+  Currently supported: ARM, Intel x86, MIPS, NDS32, Nios II, PowerPC).

 * Compression Type (uncompressed, gzip, bzip2)
 * Load Address
 * Entry Point
 * Compression Type (uncompressed, gzip, bzip2)
 * Load Address
 * Entry Point


@@ -5800,9 +5019,9 @@ configuration for CS0# this is a mirror of the on board Flash memory.
 To be able to re-map memory U-Boot then jumps to its link address.
 To be able to implement the initialization code in C, a (small!)
 initial stack is set up in the internal Dual Ported RAM (in case CPUs
 To be able to re-map memory U-Boot then jumps to its link address.
 To be able to implement the initialization code in C, a (small!)
 initial stack is set up in the internal Dual Ported RAM (in case CPUs

-which provide such a feature like MPC8xx or MPC8260), or in a locked
-part of the data cache. After that, U-Boot initializes the CPU core,
-the caches and the SIU.
+which provide such a feature like), or in a locked part of the data
+cache. After that, U-Boot initializes the CPU core, the caches and
+the SIU.

 
 Next, all (potentially) available memory banks are mapped using a
 preliminary mapping. For example, we put them on 512 MB boundaries
 
 Next, all (potentially) available memory banks are mapped using a
 preliminary mapping. For example, we put them on 512 MB boundaries


@@ -5940,7 +5159,7 @@ may be rejected, even when they contain important and valuable stuff.
 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
 
 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
 
 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;

-see http://lists.denx.de/mailman/listinfo/u-boot
+see https://lists.denx.de/listinfo/u-boot

 
 When you send a patch, please include the following information with
 it:
 
 When you send a patch, please include the following information with
 it: