======================================================================
-Changes since U-Boot 0.2.2:
+Changes since U-Boot 1.0.1:
======================================================================
+* Patch by Travis Sawyer, 30 Dec 2003:
+ Add support for IBM PPC440GX. Multiple EMAC Ethernet devices,
+ select MDI port based on enabled EMAC device.
+ Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX
+ base PrPMC board.
+
+* Patch by Wolter Kamphuis, 15 Dec 2003:
+ made CONFIG_SILENT_CONSOLE usable on all architectures
+
+* Disable date command on TQM866M - there is no RTC on MPC866
+
+* Fix variable CPU clock for MPC859/866 systems for low CPU clocks
+
+* Implement adaptive SDRAM timing configuration based on actual CPU
+ clock frequency for INCA-IP; fix problem with board hanging when
+ switching from 150MHz to 100MHz
+
+* Add PCMCIA CS support for BMS2003 board
+
+* Add variable CPU clock for MPC859/866 systems (so far only TQM866M):
+ see doc/README.MPC866 for details;
+ implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866;
+ calculate CPU clock frequency from PLL register values.
+
+* Add support for 128 MB RAM on TQM8xxL/M modules
+
+* Fix PS/2 keyboard problem caused by statically initialized variable
+ pointing to a location in flash
+
+* Fix INCA-IP clock calculation: 400/3 = 133.3 MHz, not 130.
+
+* The PS/2 mux on the BMS2003 board needs 450 ms after power on
+ before we can access it; add delay in case we are faster (with no
+ CF card inserted)
+
+* Cleanup of some init functions
+
+* Make sure SCC Ethernet is always stopped by the time we boot Linux
+ to avoid Linux crashes by early packets coming in.
+
+* Accelerate flash accesses on LWMON board by using buffered writes
+
+* Fix typo in Makefile;
+ fix problem with PARTNUM detection
+
+* Patch by Reinhard Meyer, 09 Jan 2004:
+ - add RTC support for MPC5200 based boards (requires RTC_XTAL)
+
+* Add support for IDE LED on BMS2003 board
+ (exclusive with status LED!)
+
+* Add support for PS/2 keyboard (used with PS/2 multiplexor on
+ BMS2003 board)
+
+* Patches by Reinhard Meyer, 4 Jan 2004 + 7 Jan 2004:
+ Add common files for "emk" boards
+
+* Add a common get_ram_size() function and modify the the
+ board-specific files to invoke that common implementation.
+
+======================================================================
+Changes for U-Boot 1.0.1:
+======================================================================
+
+* Set default clock for INCA-IP to 150 MHz
+
+* Make BMS2003 use a separate config file to avoid #ifdef mess;
+ add I2C support; add support for DS1337 RTC
+
+* Add CompactFlash support for BMS2003 board
+
+* Add support for status LED on BMS2003 board
+
+* Patch by Scott McNutt, 02 Jan 2004:
+ Add support for the Nios Active Serial Memory Interface (ASMI)
+ on Cyclone devices
+
+* Patch by Andrea Marson, 16 Dec 2003:
+ Add support for the PPChameleon ME and HI modules
+
+* Patch by Yuli Barcohen, 22 Dec 2003:
+ Add support for Motorola DUET ADS board (MPC87x/88x)
+
+* Patch by Robert Schwebel, 15 Dec 2003:
+ add support for cramfs (uses JFFS2 command interface)
+
+* Patches by Stephan Linz, 11 Dec 2003:
+ - more documentation for NIOS port
+ - new struct nios_pio_t, struct nios_spi_t
+ - Reconfiguration for NIOS Development Kit DK1C20:
+ o move board related code from board/dk1c20
+ to board/altera/dk1c20
+ o create a new common source path board/altera/common
+ and move generic flash access stuff into it
+ o change/expand configuration file DK1C20.h
+ - Add support for NIOS Development Kit DK1S10
+ - Add status LED support for NIOS systems
+ - Add dual 7-segment LED support for Altera NIOS DevKits
+
+* Patch by Ronen Shitrit, 10 Dec 2003:
+ Add support for the Marvell DB64360 / DB64460 development boards
+
+* Patch by Detlev Zundel, 10 Dec 2003:
+ fix dependency problem in examples/Makefile
+
+* Patch by Denis Peter, 8 Dec 2003
+ - add support for the PATI board (MPC555)
+ - add SPI support for the MPC5xx
+
+* Patch by Anders Larsen, 08 Dec 2003:
+ add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG
+ to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target;
+ cleanup some redundand #defines
+
+* Patch by André Schwarz, 8 Dec 2003:
+ fixes for Davicom DM9102A Ethernet Chip (#define CONFIG_TULIP_FIX_DAVICOM):
+ - TX and RX deskriptors must be quad-word aligned
+ - does not work with only one TX deskriptor
+ - standard reset method does not work
+
+* Patch by Masami Komiya, 08 Dec 2003:
+ add RTL8139 ethernet driver
+
+* Patches by Ed Okerson, 07 Dec 2003:
+ - fix ethernet for the AU1x00 processors in little-endian mode.
+ - extend memsetup.S for the AU1x00 processors in BE and LE modes
+
+* Minor code cleanup (coding style)
+
+* Patch by Reinhard Meyer, 30 Dec 2003:
+ - cpu/mpc5xxx/fec.c: added CONFIG_PHY_ADDR, added CONFIG_PHY_TYPE,
+ - added CONFIG_PHY_ADDR to include/configs/IceCube.h,
+ - turned debug print of PHY registers into a function (called in two places)
+ - added support for EMK MPC5200 based modules
+
+* Fix MPC8xx PLPRCR_MFD_SHIFT typo
+
+* Add support for TQM866M modules
+
+* Fixes for TQM855M with 4 MB flash (Am29DL163 = _no_ mirror bit flash)
+
+* Fix a few compiler warnings
+
+* Patch by Reinhard Meyer, 28 Dec 2003:
+ Add initial support for TOP5200 board
+
+* Make CPU clock on ICA-IP board controllable by a "cpuclk"
+ environment variable which can set to "100", "133", or "150". The
+ CPU clock will be configured accordingly upon next reboot. Other
+ values are ignored. In case of an invalid or undefined "cpuclk"
+ value, the compile-time default CPU clock speed will be used.
+
+* Enable Quad-UART on BMS2003 board (initialize the PCMCIA memory
+ window that is used to access the UART registers by the Linux driver)
+
+* Patch by Reinhard Meyer, 20 Dec 2003:
+ Fix clock calculation for the MPC5200 for higher clock frequencies
+ (above 2**32 / 10 = 429.5 MHz).
+
+* Fix CONFIG_PLL_PCI_TO_MEM_MULTIPLIER divider error in SP8240 configuration
+
+* Fix IceCube CLKIN configuration (it's 33.000000MHz)
+
+* Add new configuration for IceCube board with DDR memory
+
+* Update TRAB memory configurations
+
+* Add JFFS2 support for INCA-IP board
+
+* Patch by Bill Hargen, 09 Dec 2003:
+ - BUBINGA405EP: changed flash driver to protect top sector containing
+ first instruction.
+ - BUBINGA405EP: configured "eeprom" command to access boot config EEPROM.
+ - BUBINGA405EP: fixed PLL init (init chip selects before FPGA/NVRAM access).
+ - 405EP: fixed SPD-based SDRAM init (only use banks 0 and 1).
+ - 405EP: added/fixed support for "reginfo" command.
+ - 4xx: removed spurious MII error messages on "mii info" command.
+
+* Patch by Bernhard Kuhn, 28 Nov 2003:
+ add support for Coldfire CPU
+ add support for Motorola M5272C3 and M5282EVB boards
+
+* Patch by Pierre Aubert, 24 Nov 2003:
+ - add a return value for the fpga command
+ - add ide_preinit() function called in ide_init if CONFIG_IDE_PREINIT
+ is defined. If ide_preinit fails, ide_init is aborted.
+ - fix an endianess problem in fat.h
+
+* Patch by Wolter Kamphuis, 05 Dec 2003:
+ Add support for SNMC's QS850/QS823/QS860T boards
+
+* Patch by Yuli Barcohen, 3 Dec 2003:
+ "revive" U-Boot support for old Motorola MPC860ADS board
+
+* Patch by Cam(ilo?), 03 Dec 2003:
+ make examples build even with broken Montavista objcopy
+
+* Patch by Pavel Bartusek, 27 Nov 2003:
+ fix conversion problem with "bootretry" evironment variable
+
+* Patch by Andre Schwarz, 24 Nov 2003:
+ add support for mvblue (mvBlueLYNX and mvBlueBOX) boards
+
+* Patch by Pavel Bartusek, 21 Nov 2003:
+ set ZMII bridge speed on 440
+
+* Patch by Anders Larsen, 17 Nov 2003:
+ Fix mismatched #ifdef / #endif in include/asm-arm/arch-pxa/hardware.h
+
+* Patches by David Müller, 14 Nov 2003:
+ - board/mpl/common/common_util.c
+ * implement support for BZIP2 compressed images
+ * various cleanups (printf -> puts, ...)
+ - board/mpl/common/flash.c
+ * report correct errors to upper layers
+ * check the erase fail and VPP low bits in status reg
+ - board/mpl/vcma9/cmd_vcma9.c
+ - board/mpl/vcma9/flash.c
+ * various cleanups (printf -> puts, ...)
+ - common/cmd_usb.c
+ * fix typo in comment
+ - cpu/arm920t/usb_ohci.c
+ * support for S3C2410 is missing in #if line
+ - drivers/cs8900.c
+ * reinit some registers in case of error (cable missing, ...)
+ - fs/fat/fat.c
+ * support for USB/MMC devices is missing in #if line
+ - include/configs/MIP405.h
+ - include/configs/PIP405.h
+ * enable BZIP2 support
+ * enlarge malloc space to 1MiB because of BZIP2 support
+ - include/configs/VCMA9.h
+ * enable BZIP2 support
+ * enlarge malloc space to 1MiB because of BZIP2 support
+ * enable USB support
+ - lib_arm/armlinux.c
+ * change calling convention of ARM Linux kernel as
+ described on http://www.arm.linux.org.uk/developer/booting.php
+
+* Patch by Thomas Lange, 14 Nov 2003:
+ Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to
+ support all these AMD boards.
+
+* Patch by Thomas Lange, 14 Nov 2003:
+ Workaround for mips au1x00 physical memory accesses (the au1x00
+ uses a 36 bit bus internally and cannot access physical memory
+ directly. Use the uncached SDRAM address instead of the physical
+ one.)
+
+* Patch by Xue Ligong (Joe), 13 Nov 2003:
+ add Realtek 8019 ethernet driver
+
+* Patch by Yuli Barcohen, 13 Nov 2003:
+ MPC826xADS/PQ2FADS cleanup
+
+* Patch by Anders Larsen, 12 Nov 2003:
+ Update README to mark the PORTIO commands non-standard
+
+* Patch by Nicolas Lacressonnière, 12 Nov 2003:
+ update for for Atmel AT91RM9200DK development kit:
+ - support for environment variables in DataFlash
+ - Atmel DataFlash AT45DB1282 support
+
+* Patch by Jeff Carr, 11 Nov 2003:
+ add support for new version of 8270 processors
+
+* Patches by George G. Davis, 05 Nov 2003:
+ - only pass the ARM linux initrd tag to the kernel when an initrd
+ is actually present
+ - update omap1510inn configuration file
+
+* Patches by Stephan Linz, 3 Nov 2003:
+ - more endianess fixes for LAN91C111 driver
+ - CFG_HZ configuration patch for NIOS Cyclone board
+
+* Patch by Stephan Linz, 28 Oct 2003:
+ fix PHY_INT_REG vs. PHY_MASK_REG bug in drivers/smc91111.c
+
+* Patch by Steven Scholz, 20 Oct 2003:
+ - make "mii info <addr>" show infor for PHY at "addr" only
+ - Endian fix for miiphy_info()
+
+* Patch by Gleb Natapov, 19 Sep 2003:
+ Move most of the timer interrupt related PPC code to ppc_lib/interrupts.c
+
+* Patch by Anders Larsen, 17 Sep 2003:
+ Bring ARM memory layout in sync with the documentation:
+ stack and malloc-heap are now located _below_ the U-Boot code
+
+* Accelerate booting on TRAB board: read and check autoupdate image
+ headers first instead of always reading the whole images.
+
+* Fix type in MPC5XXX code (pointed out by Victor Wren)
+
+* Enabled password check on RMU board
+
+* Fix configuration problem with IceCube in LOWBOOT configuration:
+ envrionment got embedded, corrupting the image layout.
+
+* Fix NEC display names (it's 6440 [for 640x480], not 6640).
+
+* Added BMS2003 board
+ add support for NEC NL6448BC33-54. 10.4", 640x480 TFT display
+
+* Fix flash driver for TRAB board (must use Unlock Bypass Reset
+ command to exit Unlock Bypass Mode); adjust timings for flash, SRAM
+ and CPLD
+
+* Use "-fPIC" instead of "-mrelocatable" to prevent problems with
+ recent tools
+
+* Add checksum verification to 'imls' command
+
+* Add bd_info fields needed for 4xx Linux I2C driver
+
+* Patch by Martin Krause, 4 Nov. 2003:
+ Fix error in cmd_vfd.c (TRAB board: "vfd /1" shows now only one Bitmap)
+
+* Print used network interface when CONFIG_NET_MULTI is set
+
+* Patch by Bernhard Kuhn, 28 Oct 2003:
+ Add low boot support for MPC5200
+
+* Fix problem with dual PCMCIA support (NSCU)
+
+* Fix MPC5200 I2C initialization function
+
+======================================================================
+Changes for U-Boot 1.0.0:
+======================================================================
+
+* Fix parameter passing to standalone images with bootm command
+
+* Patch by Kyle Harris, 30 Oct 2003:
+ Fix build errors for ixdp425 board
+
+* Patch by David M. Horn, 29 Oct 2003:
+ Fixes to build under CYGWIN
+
+* Get IceCube MGT5100 working (again)
+
+* Fix problems in memory test on some boards (which was not
+ non-destructive as intended)
+
+* Patch by Gary Jennejohn, 28 Oct 2003:
+ Change fs/fat/fat.c to put I/O buffers in BSS instead on the stack
+ to prevent stack overflow on ARM systems
+
+* Patch by Stephan Linz, 28 Oct 2003:
+ fix init sequence error for NIOS port
+
+* Allow lowercase spelling for IceCube_5200; support MPC5200LITE name
+
+* Add CONFIG_VERSION_VARIABLE to TRAB configuration
+
+* Patch by Xiao Xianghua, 23 Oct 2003:
+ small patch for mpc85xx
+
+* Fix small problem in MPC5200 I2C driver
+
+* Fix FCC3 support on ATC board
+
+* Correct header printing for multi-image files in do_bootm()
+
+* Make CONFIG_SILENT_CONSOLE work with CONFIG_AUTOBOOT_KEYED
+
+* Fix PCI problems on PPChameleon board
+
+* Patch by Steven Scholz, 18 Oct 2003:
+ Fix AT91RM9200 ethernet driver
+
+* Patch by Nye Liu, 17 Oct 2003:
+ Fix typo in include/mpc8xx.h
+
+* Patch by Richard Woodruff, 16 Oct 03:
+ Fixes for cpu/arm925/interrupt.c
+ - Initialize timestamp & lastdec vars.
+ - fix timestamp overflows.
+ - fix lastdec overflow.
+ - smarter normalization to allow udelay() below 1ms to work.
+
+* Patch by Scott McNutt, 16 Oct
+ add networking support for the Altera Nios Development Kit,
+ Cyclone Edition (DK-1C20)
+
+* Patch by Jon Diekema, 14 Oct 2003:
+ add hint about doc/README.silent to README file
+
+* Add CompactFlash support for NSCU
+
+* Fix PCI problems on PPChameleonEVB
+
+* TRAB auto-update: Base decision if we have to strip the image
+ header on image type as encoded in the header
+ (include image type patch by Martin Krause, 17 Oct 2003)
+
+* Patches by Xianghua Xiao, 15 Oct 2003:
+
+ - Added Motorola CPU 8540/8560 support (cpu/85xx)
+ - Added Motorola MPC8540ADS board support (board/mpc8540ads)
+ - Added Motorola MPC8560ADS board support (board/mpc8560ads)
+
+* Fix flash timings on TRAB board
+
+* Make sure HUSH is initialized for running auto-update scripts
+
+* Make 5200 reset command _really_ reset the board, without running
+ any other code after it
+
+* Fix errors with flash erase when range spans across banks
+ that are mapped in reverse order
+
+* Fix flash mapping and display on P3G4 board
+
+* Patch by Kyle Harris, 15 Jul 2003:
+ - add support for Intel IXP425 CPU
+ - add support for IXDP425 eval board
+
+* Added config option CONFIG_SILENT_CONSOLE. See doc/README.silent
+ for more information
+
+* Patch by Steven Scholz, 10 Oct 2003
+ - Add support for Altera FPGA ACEX1K
+
+* Patches by Thomas Lange, 09 Oct 2003:
+ - fix cmd_ide.c for non ppc boards (read/write functions did not
+ add ATA base address)
+ - fix for shannon board
+ - #ifdef CONFIG_IDE_8xx_DIRECT some otherwise unused code
+ - Endian swap ATA identity for all big endian CPUs, not just PPC
+ - MIPS only: New option CONFIG_MEMSIZE_IN_BYTES for passing memsize
+ args to linux
+ - add support for dbau1x00 board (MIPS32)
+
+* Patch by Sangmoon Kim, 07 Oct 2003:
+ add support for debris board
+
+* Patch by Martin Krause, 09 Oct 2003:
+ Fixes for TRAB board
+ - /board/trab/rs485.c: correct baudrate
+ - /board/trab/cmd_trab.c: bug fix for problem with timer overflow in
+ udelay(); fix some timing problems with adc controller
+ - /board/trab/trab_fkt.c: add new commands: gain, eeprom and power;
+ modify commands: touch and buzzer
+
+* Disable CONFIG_SUPPORT_VFAT when used with CONFIG_AUTO_UPDATE
+ (quick & dirty workaround for rogue pointer problem in get_vfatname());
+ Use direct function calls for auto_update instead of hush commands
+
+* Patch by Scott McNutt, 04 Oct 2003:
+ - add support for Altera Nios-32 CPU
+ - add support for Nios Cyclone Development Kit (DK-1C20)
+
+* Patch by Steven Scholz, 29 Sep 2003:
+ - A second parameter for bootm overwrites the load address for
+ "Standalone Application" images.
+ - bootm sets environment variable "filesize" to the resulting
+ (uncompressed) data length for "Standalone Application" images
+ when autostart is set to "no". Now you can do something like
+ if bootm $fpgadata $some_free_ram ; then
+ fpga load 0 $some_free_ram $filesize
+ fi
+
+* Patch by Denis Peter, 25 Sept 2003:
+ add support for the MIP405 Rev. C board
+
+* Patch by Yuli Barcohen, 25 Sep 2003:
+ add support for Zephyr Engineering ZPC.1900 board
+
+* Patch by Anders Larsen, 23 Sep 2003:
+ add CMD_PORTIO to CFG_CMD_NONSTD (commands in question are only
+ implemented for the x86 architecture)
+
+* Patch by Sangmoon Kim, 23 Sep 2003:
+ fix pll_pci_to_mem_multiplier table for MPC8245
+
+* Patch by Anders Larsen, 22 Sep 2003:
+ enable timed autoboot on PXA
+
+* Patch by David Müller, 22 Sep 2003:
+ - add $(CFLAGS) to "-print-libgcc-filename" so compiler driver
+ returns correct libgcc file path
+ - "latency" reduction of busy-loop waiting to improve "U-Boot" boot
+ time on s3c24x0 systems
+
+* Patch by Jon Diekema, 19 Sep 2003:
+ - Add CFG_FAULT_ECHO_LINK_DOWN option to echo the inverted Ethernet
+ link state to the fault LED.
+ - In NetLoop, make the Fault LED reflect the link status. The link
+ status gets updated on entry, and on timeouts.
+
+* Patch by Anders Larsen, 18 Sep 2003:
+ allow mkimage to build and run on Cygwin-hosted systems
+
+* Patch by Frank Müller, 18 Sep 2003:
+ use bi_intfreq instead of bi_busfreq to compute fec_mii_speed in
+ cpu/mpc8xx/fec.c
+
+* Patch by Pantelis Antoniou, 16 Sep 2003:
+ add tool to compute fileds in the PLPRCR register for MPC86x
+
+* Use IH_TYPE_FILESYSTEM for TRAB "disk" images.
+
+* Fix build problems under FreeBSD
+
+* Add generic filesystem image type
+
+* Make fatload set filesize environment variable
+
+* enable basic / medium / high-end configurations for PPChameleonEVB
+ board; fix NAND code
+
+* enable TFTP client code to specify to the server the desired
+ timeout value (see RFC-2349)
+
+* Improve SDRAM setup for TRAB board
+
+* Suppress all output with splashscreen configured only if "splashimage"
+ is set
+
+* Fix problems with I2C support for mpc5200
+
+* Adapt TRAB configuration and auto_update to new memory layout
+
+* Add configuration for wtk board
+
+* Add support for the Sharp LQ065T9DR51U LCD display
+
+* Patch by Rune Torgersen, 17 Sep 2003:
+ - Fixes for MPC8266 default config
+ - Allow eth_loopback_test() on 8260 to use a subset of the FCC's
+
+* Patches by Jon Diekema, 17 Sep 2003:
+ - update README (SHOW_BOOT_PROGRESS values for cmd_nand.c and
+ env_common.c)
+ - sbc8260 tweaks
+ - adjust "help" output
+
+* Patches by Anders Larsen, 17 Sep 2003:
+ - fix spelling errors
+ - set GD_FLG_DEVINIT flag only after device function pointers
+ are valid
+ - Allow CFG_ALT_MEMTEST on systems where address zero isn't
+ writeable
+ - enable 3.rd UART (ST-UART) on PXA(XScale) CPUs
+ - trigger watchdog while waiting in serial driver
+
+* Add auto-update code for TRAB board using USB memory sticks,
+ support new configuration with more memory
+
+* disable MPC5200 bus pipelining as workaround for bus contention
+
+* Modify XLB arbiter priorities on MPC5200 so all devices use same
+ priority; configure critical interrupts to be handled like external
+ interrupts
+
+* Make IPB clock on MGT5100/MPC5200 configurable in board config file;
+ go back to 66 MHz for stability
+
+* Patches by Jon Diekema, 15 Sep 2003:
+ - add description for missing CFG_CMD_* entries in the README file
+ - sacsng tweaks
+
+* Patch by Gleb Natapov, 14 Sep 2003:
+ enable watchdog support for all MPC824x boards that have a watchdog
+
+* On MPC5200, restrict FEC to a maximum of 10 Mbps to work around the
+ "Non-octet Aligned Frame" errors we see at 100 Mbps
+
+* Patch by Sharad Gupta, 14 Sep 2003:
+ fix SPR numbers for upper BAT register ([ID]BAT[4-7][UL])
+
+* Patch by llandre, 11 Sep 2003:
+ update configuration for PPChameleonEVB board
+
+* Patch by David Müller, 13 Sep 2003:
+ various changes to VCMA9 board specific files
+
+* Add I2C support for MGT5100 / MPC5200
+
+* Patch by Rune Torgersen, 11 Sep 2003:
+ Changed default memory option on MPC8266ADS to NOT be Page Based
+ Interleave, since this doesn't work very well with the standard
+ 16MB DIMM
+
+* Patch by George G. Davis, 12 Sep 2003:
+ fix Makefile settings for sk98 driver
+
+* Patch by Stefan Roese, 12 Sep 2003:
+ - new boards added: DP405, HUB405, PLU405, VOH405
+ - some esd boards updated
+ - cpu/ppc4xx/sdram.c: disable memory controller before setting
+ first values
+ - cpu/ppc4xx/405_pci.c: set vendor id on PPC405EP systems
+
+* Patch by Martin Krause, 11 Sep 2003:
+ add burn-in tests for TRAB board
+
+* Enable instruction cache on MPC5200 board
+
+* Patch by Denis Peter, 11 Sep 2003:
+ - fix USB data pointer assignment for bulk only transfer.
+ - prevent to display erased directories in FAT filesystem.
+
+* Change output format for NAND flash - make it look like for other
+ memory, too
+
+======================================================================
+Changes for U-Boot 0.4.8:
+======================================================================
+
+* Add I2C and RTC support for RMU board
+
+* Patches by Denis Peter, 9 Sep 2003:
+ add FAT support for IDE, SCSI and USB
+
+* Patches by Gleb Natapov, 2 Sep 2003:
+ - cleanup of POST code for unsupported architectures
+ - MPC824x locks way0 of data cache for use as initial RAM;
+ this patch unlocks it after relocation to RAM and invalidates
+ the locked entries.
+
+* Patch by Gleb Natapov, 30 Aug 2003:
+ new I2C driver for mpc107 bridge. Now works from flash.
+
+* Patch by Dave Ellis, 11 Aug 2003:
+ - JFFS2: fix typo in common/cmd_jffs2.c
+ - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option
+ - JFFS2: remove node version 0 warning
+ - JFFS2: accept JFFS2 PADDING nodes
+ - SXNI855T: add AM29LV800 support
+ - SXNI855T: move environment from EEPROM to flash
+ - SXNI855T: boot from JFFS2 in NOR or NAND flash
+
+* Patch by Bill Hargen, 11 Aug 2003:
+ fixes for I2C on MPC8240
+ - fix i2c_write routine
+ - fix iprobe command
+ - eliminates use of global variables, plus dead code, cleanup.
+
+* Add support for USB Mass Storage Devices (BBB)
+ (tested with USB memory sticks only)
+
+* Avoid flicker on TRAB's VFD
+
+* Add support for SK98xx driver
+
+* Add PCI support for SL8245 board
+
+* Support IceCube board configurations with 1 x AMD AM29LV065 (8 MB)
+ or 1 x AM29LV652 (two LV065 in one chip = 16 MB);
+ Run IPB at 133 Mhz; adjust the MII clock frequency accordingly
+
+* Set BRG_CLK on PM825/826 to 64MHz (VCO_OUT / 4, instead of 16 MHz)
+ to allow for more accurate baudrate settings
+ (error now 0.7% at 115 kbps, instead of 3.5% before)
+
+* Patch by Andreas Mohr, 4 Sep 2003:
+ Fix a lot of spelling errors
+
+* Add support for PPChameleon Eval Board
+
+* Add support for P3G4 board
+
+* Fix problem with MGT5100 FEC driver: add "early" MAC address
+ initialization
+
+* Patch by Yuli Barcohen, 7 Aug 2003:
+ check BCSR to detect if the board is configured in PCI mode
+
+======================================================================
+Changes for U-Boot 0.4.7:
+======================================================================
+
+* Patch by Raghu Krishnaprasad, 7 Aug 2003:
+ add support for Adder II MPC852T module
+
+* Patch by George G. Davis, 19 Aug 2003:
+ fix TI Innovator/OMAP1510 pin configs
+
+* Patches by Kshitij, 18 Aug 2003
+ - add support for arm926ejs cpu core
+ - add support for TI OMAP 1610 Innovator Board
+
+* Patch by Yuli Barcohen, 14 Aug 2003:
+ add support for bzip2 uncompression
+
+* Add GCC library to examples/Makefile so GCC utility functions will
+ be resolved, too
+
+* Add I2C and RTC support for RMU board using software I2C driver
+ (because of better response to iprobe command); fix problem with
+ "reset" command
+
+* Patch by Matthias Fuchs, 28 Aug 2003:
+ Added CONFIG_BOOTP_DNS2 and CONFIG_BOOTP_SEND_HOSTNAME to
+ CONFIG_BOOTP_MAKS (see README).
+
+* Fix ICU862 environment problem
+
+* Fix RAM size detection for RMU board
+
+* Implement "reset" for MGT5100/MPC5200 systems
+
+======================================================================
+Changes for U-Boot 0.4.6:
+======================================================================
+
+* Make Ethernet autonegotiation on INCA-IP work for all clock rates;
+ allow selection of clock frequency as "make" target
+
+* Implement memory autosizing code for IceCube boards
+
+* Configure network port on INCA-IP for autonegotiation
+
+* Fix overflow problem in network timeout code
+
+* Patch by Richard Woodruff, 8 Aug 2003:
+ Allow crc32 to be used at address 0x000 (crc32_no_comp, too).
+
+======================================================================
+Changes for U-Boot 0.4.5:
+======================================================================
+
+* Update for TQM board defaults:
+ disable clocks_in_mhz, enable boot count limit
+
+* Removed tools/gdb from "make all" target. Added make target "gdbtools"
+ in toplevel directory instead. Removed astest.c from tools/gdb because
+ it is no longer relevant.
+
+* Fix PCI support for MPC5200 / IceCube Board
+
+* Map ISP1362 USB OTG controller for NSCU board
+
+* Patch by Brad Parker, 02 Aug 2003:
+ fix sc520_cdp problems
+
+* Implement Boot Cycle Detection (Req. 2.3 of OSDL CGL Reqirements)
+
+* Allow erase command to cross flash bank boundaries
+
+* Patch by Scott McNutt, 21 Jul 2003:
+ Add support for LynuxWorks Kernel Downloadable Images (KDIs).
+ Both LynxOS and BlueCat linux KDIs are supported.
+
+* Patch by Richard Woodruff, 25 Jul 2003:
+ use more reliable reset for OMAP/925T
+
+* Patch by Nye Liu, 25 Jul 2003:
+ fix typo in mpc8xx.h
+
+* Patch by Richard Woodruff, 24 Jul 2003:
+ Fixes for cmd_nand.c:
+ - Fixed null dereferece which could result in incorrect ECC values.
+ - Added support for devices with no Ready/Busy signal hooked up.
+ - Added OMAP1510 read/write protect handling.
+ - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
+ for non-JFFS2.
+ - Switched default ECC to be JFFS2.
+
+* Allow crc32 to be used at address 0x000
+
+* Provide consistent interface to standalone applications to access
+ the 'global_data' structure
+ Provide a doc/README.standalone more useful to users/developers.
+
+* Make IceCube MGT5100 FEC driver work
+
+* Implement new mechanism to export U-Boot's functions to standalone
+ applications: instead of using (PPC-specific) system calls we now
+ use a jump table; please see doc/README.standalone for details
+
+* Patch by Dave Westwood, 24 Jul 2003:
+ added support for Unity OS (a proprietary OS)
+
+* Patch by Detlev Zundel, 23 Jul 2003:
+ add "imls" command to print flash table of contents
+
+* Fix cold boot detection for log buffer reset
+
+* Return error for invalid length specifiers with "cp.X" etc.
+
+* Fix startup problem on MIPS
+
+* Allow for CONFIG_SPLASH_SCREEN even when no explicit
+ bitmap support is configured
+
+* Patch by Bill Hargen, 18 Jul 2003:
+ - fix endinaness problem in cpu/mpc824x/drivers/i2c/i2c1.c
+
+* Patch by Denis Peter, 18 Jul 2003:
+ - fix memory configuration for MIP405T
+ - fix printout of baudrate for "loadb <loadaddr> <baudrate>"
+
+* Cleanup of TQM82xx configurations; use "official" board types
+ to make selection easier.
+
+* Patch by Martin Krause, 17 Jul 2003:
+ add delay to get I2C working with "imm" command and s3c24x0_i2c.c
+
+* Patch by Richard Woodruff, 17 July 03:
+ - Fixed bug in OMAP1510 baud rate divisor settings.
+
+* Patch by Nye Liu, 16 July 2003:
+ MPC860FADS fixes:
+ - add MPC86xADS support (uses MPC86xADS.h)
+ - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
+ o PLPRCR changes
+ o BRG changes (EXTAL/XTAL restricted to 10MHz)
+ o don't trust gclk() software measurement by default, depend on
+ CONFIG_8xx_GCLK_FREQ
+ - add DRAM SIMM not installed detection
+ - use more "correct" SDRAM initialization sequence
+ - allow different SDRAM sizes (8xxADS has 8M)
+ - default DER is 0
+ - remove unused MAMR defines from FADS860T.h (all done in fads.c)
+ - rename MAMR/MBMR defines to be more consistent. Should eventually
+ be merged into MxMR to better reflect the PowerQUICC datasheet.
+
+* Patch by Yuli Barcohen, 16 Jul 2003:
+ support new Motorola PQ2FADS-ZU evaluation board which replaced
+ MPC8260ADS and MPC8266ADS
+
+======================================================================
+Changes for U-Boot 0.4.4:
+======================================================================
+
+* Add support for IceCube board (with MGT5100 and MPC5200 CPUs)
+
+* Add support for MGT5100 and MPC5200 processors
+
+* Patch by Lutz Dennig, 15 Jul 2003:
+ update for R360MPI board
+
+======================================================================
+Changes for U-Boot 0.4.3:
+======================================================================
+
+* Patches by Kshitij, 04 Jul 2003
+ - added support for arm925t cpu core
+ - added support for TI OMAP 1510 Innovator Board
+
+* Patches by Martin Krause, 14 Jul 2003:
+ - add I2C support for s3c2400 systems (trab board)
+ - (re-) add "ping" to command table
+
+* Fix handling of "slow" POST routines
+
+* Patches by Yuli Barcohen, 13 Jul 2003:
+ - Correct flash and JFFS2 support for MPC8260ADS
+ - fix PVR values and clock generation for PowerQUICC II family
+ (8270/8275/8280)
+
+* Patch by Bernhard Kuhn, 08 Jul 2003:
+ - add support for M68K targets
+
+* Patch by Ken Chou, 3 Jul:
+ - Fix PCI config table for A3000
+ - Fix iobase for natsemi.c
+ (PCI_BASE_ADDRESS_0 is the IO base register for DP83815)
+
+* Allow to enable "slow" POST routines by key press on power-on
+* Fix temperature dependend switching of LCD backlight on LWMON
+* Tweak output format for LWMON
+
+* Patch by Stefan Roese, 11 Jul 2003:
+ - Fix bug in CONFIG_VERSION_VARIABLE.
+ - AR405 config updated.
+ - OCRTC/ORSG: bsp command added.
+ - ASH405 bsp update.
+
+======================================================================
+Changes for U-Boot 0.4.2:
+======================================================================
+
+* Add support for NSCU board
+
+* Add support for TQM823M, TQM850M, TQM855M and TQM860M modules
+
+* Add support for Am29LV160ML, Am29LV320ML, and Am29LV640ML
+ mirror bit flash on TQM8xxM modules
+
+* Patch by Kenneth Johansson, 30 Jun 2003:
+ get rid of MK_CMD_ENTRY macro; update doc/README.command
+
+* Patch by Seb James, 30 Jun 2003:
+ Improve documentation of I2C configuration in README
+
+* Fix problems with previous log buffer "fixes"
+
+* Fix minor help text issues
+
+* "log append" did not append a newline
+
+======================================================================
+Changes for U-Boot 0.4.1:
+======================================================================
+
+* Fix some missing commands, cleanup header files
+ (autoscript, bmp, bsp, fat, mmc, nand, portio, ...)
+
+* Rewrite command lookup and help command (fix problems with bubble
+ sort when sorting command name list). Minor cleanup here and there.
+
+* Merge from "stable branch", tag LABEL_2003_06_28_1800-stable:
+ - Allow to call sysmon function interactively
+ - PIC on LWMON board needs delay after power-on
+ - Add missing RSR definitions for MPC8xx
+ - Improve log buffer handling: guarantee clean reset after power-on
+ - Add support for EXBITGEN board (aka "genie")
+ - Add support for SL8245 board
+
+* Code cleanup:
+ - remove trailing white space, trailing empty lines, C++ comments, etc.
+ - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
+
+* Patches by Kenneth Johansson, 25 Jun 2003:
+ - major rework of command structure
+ (work done mostly by Michal Cendrowski and Joakim Kristiansen)
+
+======================================================================
+Changes for U-Boot 0.4.0:
+======================================================================
+
+* Patches by Robert Schwebel, 26 Jun 2003:
+ - csb226 configuration updated
+ - credits for logodl port updated
+ - innokom configuration updated
+ - logodl tree update, still with coding style inconsistencies
+ - added OCM for ppc405 warning to README
+
+* Patch by Pantelis Antoniou, 25 Jun 2003:
+ update NetVia with V2 board support
+
+* Header file cleanup for ARM
+
+* Patch by Murray Jensen, 24 Jun 2003:
+ - make sure to use only U-boot provided header files
+ - fix problems with ".rodata.str1.4" section as used by GCC-3.x
+
+* Patch by Stefan Roese, 24 Jun 2003:
+ - Update esd ASH405 board files.
+ - Update esd DASA_SIM config file.
+ - Add ping command to some esd boards.
+
+* Patch by Yuli Barcohen, 23 Jun 2003:
+ Update for MPC8260ADS board
+
+* Patch by Murray Jensen, 23 Jun 2003:
+ - cleanup of GCC 3.x compiler warnings
+
+* Patch by Rune Torgersen, 4 Jun 2003:
+ add large memory support for MPC8266ADS board
+
+* Patch by Richard Woodruff, 19 June 03:
+ - Enabled standard u-boot device abstraction for ARM
+ - Enabled console device for ARM
+ - Initilized bi_baudrate for ARM
+
+* Patch by Bill Hargen, 23 Apr 2003:
+ fix byte order for 824x I2C addresses (write op)
+
+* Patch by Murray Jensen, 20 Jun 2003:
+ - hymod update
+ - cleanup (especially for gcc-3.x compilers)
+
+* Patch by Tom Guilliams, 20 Jun 2003:
+ added CONFIG_750FX support for IBM 750FX processors
+
+* Patch by Devin Crumb, 02 Apr 2003:
+ Fix clock divider rounding problem in drivers/serial.c
+
+* Patch by Richard Woodruff, 19 June 03:
+ - Fixed smc91c111 driver to sync with the u-boot environment
+ (driver/smc91c111.c).
+ - Added eth_init error return check in NetLoop (net/net.c).
+
+* Patch by Ken Chou, 19 June 2003:
+ Added support for A3000 SBC board (Artis Microsystems Inc.)
+
+* Patches by Murray Jensen, 17 Jun 2003:
+ - Hymod board database mods: add "who" field and new xilinx chip types
+ - provide new "init_cmd_timeout()" function so code external to
+ "common/main.c" can use the "reset_cmd_timeout()" function before
+ entering the main loop
+ - add DTT support for adm1021 (new file dtt/adm1021.c; config
+ slightly different. see include/configs/hymod.h for an example
+ (requires CONFIG_DTT_ADM1021, CONFIG_DTT_SENSORS, and
+ CFG_DTT_ADM1021 defined)
+ - add new "eeprom_probe()" function which has similar args and
+ behaves in a similar way to "eeprom_read()" etc.
+ - add 8260 FCC ethernet loopback code (new "eth_loopback_test()"
+ function which is enabled by defining CONFIG_ETHER_LOOPBACK_TEST)
+ - gdbtools copyright update
+ - ensure that set_msr() executes the "sync" and "isync" instructions
+ after the "mtmsr" instruction in cpu/mpc8260/interrupts.c
+ - 8260 I/O ports fix: Open Drain should be set last when configuring
+ - add SIU IRQ defines for 8260
+ - allow LDSCRIPT override and OBJCFLAGS initialization: change to
+ config.mk to allow board configurations to override the GNU
+ linker script, selected via the LDSCRIPT, make variable, and to
+ give an initial value to the OBJCFLAGS make variable
+ - 8260 i2c enhancement:
+ o correctly extends the timeout depending on the size of all
+ queued messages for both transmit and receive
+ o will not continue with receive if transmit times out
+ o ensures that the error callback is done for all queued tx
+ and rx messages
+ o correctly detects both tx and rx timeouts, only delivers one to
+ the callback, and does not overwrite an earlier error
+ o logic in i2c_probe now correct
+ - add "vprintf()" function so that "panic()" function can be
+ technically correct
+ - many Hymod board changes
+
+* Patches by Robert Schwebel, 14 Jun 2003:
+ - add support for Logotronic DL datalogger board
+ - cleanup serial line after kermit binary download
+ - add debugX macro (debug level support)
+ - update mach-types.h to latest arm.linux.org.uk master list.
+
+* Patches by David Müller, 12 Jun 2003:
+ - rewrite of the S3C24X0 register definitions stuff
+ - "driver" for the built-in S3C24X0 RTC
+
+* Patches by Yuli Barcohen, 12 Jun 2003:
+ - Add MII support and Ethernet PHY initialization for MPC8260ADS board
+ - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
+ configuration word supplied by FPGA on some MPC8260ADS boards
+
+* Patch by Pantelis Antoniou, 10 Jun 2003:
+ Unify status LED interface
+
+* Add support for DS12887 RTC; add RTC support for ATC board
+
+* Patch by Nicolas Lacressonniere, 11 Jun 2003:
+ Modifications for Atmel AT91RM9200DK ARM920T based development kit
+ - Add Atmel DataFlash support for reading and writing.
+ - Add possibility to boot a Linux from DataFlash with BOOTM command.
+ - Add Flash detection on Atmel AT91RM9200DK
+ (between Atmel AT49BV1614 and AT49BV1614A flashes)
+ - Replace old Ethernet PHY layer functions
+ - Change link address
+
+* Patch by Frank Smith, 9 Jun 2003:
+ use CRIT_EXCEPTION for machine check on 4xx
+
+* Patch by Detlev Zundel, 13 Jun 2003:
+ added implementation of the "carinfo" command in cmd_immap.c
+
+* Fix CONFIG_NET_MULTI support in include/net.h
+
+* Patches by Kyle Harris, 13 Mar 2003:
+ - Add FAT partition support
+ - Add command support for FAT
+ - Add command support for MMC
+ ----
+ - Add Intel PXA support for video
+ - Add Intel PXA support for MMC
+ ----
+ - Enable MMC and FAT for lubbock board
+ - Other misc changes for lubbock board
+
+* Patch by Robert Schwebel, April 02, 2003:
+ fix for SMSC91111 driver
+
+* Patch by Vladimir Gurevich, 04 Jun 2003:
+ make ppc405 ethernet driver compatible with CONFIG_NET_MULTI option
+
+* Patch by Stefan Roese, 05 Jun 2003:
+ - PPC4xx: Fix bug for initial stack in data cache as pointed out by
+ Thomas Schaefer (tschaefer@giga-stream.de). Now inital stack in
+ data cache can be used even if the chip select is in use.
+ - CFG_RX_ETH_BUFFER added to set the ethernet receive buffer count
+ (see README for further description).
+ - Changed config files of CONFIG_EEPRO100 boards to use the
+ CFG_RX_ETH_BUFFER define.
+
+* Add support for RMU board
+
+* Add support for TQM862L at 100/50 MHz
+
+* Patch by Pantelis Antoniou, 02 Jun 2003:
+ major reconstruction of networking code;
+ add "ping" support (outgoing only!)
+
+* Patch by Denis Peter, 04 June 2003:
+ add support for the MIP405T board
+
+* Patches by Udi Finkelstein, 2 June 2003:
+ - Added support for custom keyboards, initialized by defining a
+ board-specific drv_keyboard_init as well as defining CONFIG_KEYBOARD .
+ - Added support for the RBC823 board.
+ - cpu/mpc8xx/lcd.c now automatically calculates the
+ Horizontal Pixel Count field.
+
+* Fix alignment problem in BOOTP (dhcp_leasetime option)
+ [pointed out by Nicolas Lacressonnière, 2 Jun 2003]
+
+* Patch by Mark Rakes, 14 May 2003:
+ add support for Intel e1000 gig cards.
+
+* Patch by Nye Liu, 3 Jun 2003:
+ fix critical typo in MAMR definition (include/mpc8xx.h)
+
+* Fix requirement to align U-Boot image on 16 kB boundaries on PPC.
+
+* Patch by Klaus Heydeck, 2 Jun 2003
+ Minor changes for KUP4K configuration
+
+* Patch by Marc Singer, 29 May 2003:
+ Fixed rarp boot method for IA32 and other little-endian CPUs.
+
+* Patch by Marc Singer, 28 May 2003:
+ Added port I/O commands.
+
+* Patch by Matthew McClintock, 28 May 2003
+ - cpu/mpc824x/start.S: fix relocation code when booting from RAM
+ - minor patches for utx8245
+
+* Patch by Daniel Engström, 28 May 2003:
+ x86 update
+
+* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
+ add nand flash support to SXNI855T configuration
+ fix/extend nand flash support:
+ - fix 'nand erase' command so does not erase bad blocks
+ - fix 'nand write' command so does not write to bad blocks
+ - fix nand_probe() so handles no flash detected properly
+ - add doc/README.nand
+ - add .jffs2 and .oob options to nand read/write
+ - add 'nand bad' command to list bad blocks
+ - add 'clean' option to 'nand erase' to write JFFS2 clean markers
+ - make NAND read/write faster
+
+* Patch by Rune Torgersen, 23 May 2003:
+ Update for MPC8266ADS board
+
+* Get (mostly) rid of CFG_MONITOR_LEN definition; compute real length
+ instead CFG_MONITOR_LEN is now only used to determine _at_compile_
+ _time_ (!) if the environment is embedded within the U-Boot image,
+ or in a separate flash sector.
+
+* Cleanup CFG_DER #defines in config files (wd maintained only)
+
+* Fix data abort exception handling for arm920t CPU
+
+* Fix alignment problems with flash driver for TRAB board
+
+* Patch by Donald White, 21 May 2003:
+ fix calculation of base address in pci_hose_config_device()
+
+* Fix bug in command line parsing: "cmd1;cmd2" is supposed to always
+ execute "cmd2", even if "cmd1" fails. Note that this is different
+ to "run var1 var2" where the contents of "var2" will NOT be
+ executed when a command in "var1" fails.
+
+* Add zero-copy ramdisk support (requires corresponding kernel support!)
+
+* Patch by Kyle Harris, 20 May 2003:
+ In preparation for an ixp port, rename cpu/xscale and arch-xscale
+ into cpu/pxa and arch-pxa.
+
+* Patch by Stefan Roese, 23 May 2003:
+ - IBM PPC405EP port added.
+ - CONFIG_UART1_CONSOLE added. If defined internal UART1 (and not
+ UART0) is used as default U-Boot console. PPC4xx only!
+ - esd ASH405 board added (PPC405EP based).
+ - BUBINGA405EP board added (PPC405EP based - IBM Eval Board).
+ - esd CPCI405AB board added.
+ - esd PMC405 board added.
+ - Update of some esd boards.
+
+* Patch by Denis Peter, 19 Mai 2003:
+ add support for the MIP405-3 board
+
+* Patch by Dave Ellis, 22 May 2003:
+ Fix problem with only partially cleared .bss segment
+
+* Patch by Rune Torgersen, 12 May 2003:
+ get PCI to work on a MPC8266ADS board; incorporate change to
+ cpu/mpc8260/pci.c to enable overrides of PCI memory parameters
+
+* Patch by Nye Liu, 1 May 2003:
+ minor patches for the FADS8xx
+
+* Patch by Thomas Schäfer, 28 Apr 2003:
+ Fix SPD handling for 256 ECC DIMM on Walnut
+
+* Add support for arbitrary bitmaps for TRAB's VFD command;
+ allow to pass boot bitmap addresses in environment variables;
+ allow for zero boot delay
+
+* Patch by Christian Geißinger, 19 May 2002:
+ On TRAB: wait until the dummy byte has been completely sent
+
+* Patch by David Updegraff, 22 Apr 2003:
+ update for CrayL1 board
+
+* Patch by Pantelis Antoniou, 21 Apr 2003:
+ add boot support for ARTOS (a proprietary OS)
+
+* Patch by Steven Scholz, 11 Apr 2003:
+ Add support for RTC DS1338
+
+* Patch by Rod Boyce, 24 Jan 2003:
+ Fix counting of extended partitions in diskboot command
+
+* Patch by Christophe Lindheimer, 20 May 2003:
+ allow the use of CFG_LOADS when CFG_NO_FLASH is set
+
+* Fix SDRAM timing on Purple board
+
+* Add support for CompactFlash on ATC board
+ (includes support for Intel 82365 and compatible PC Card controllers,
+ and Yenta-compatible PCI-to-CardBus controllers)
+
+* Patch by Mathijs Haarman, 08 May 2003:
+ Add lan91c96 driver (tested on Lubbock and custom PXA250 board only)
+
+* Fix problem with usage of "true" (undefined in current versions of bfd.h)
+
+* Add support for Promess ATC board
+
+* Patch by Keith Outwater, 28 Apr 2003:
+ - Miscellaneous corrections and additions to GEN860T board specific code.
+ - Added GEN860_SC variant to GEN860T.
+ - Miscellaneous corrections to GEN860T documentation.
+ - Correct duplicate entry in U-Boot CREDITS file.
+ - Add GEN860T_SC entry in MAINTAINERS file.
+ - Update CREDITS file with GEN860T_SC info.
+
+* Update Smiths Aerospace addresses in MAINTAINERS file
+
+* Fix error handling in hush's version of "run" command
+
+* LWMON extensions:
+ - Splashscreen support
+ - modem support
+ - sysmon support
+ - temperature dependend enabling of LCD
+
+* Allow booting from old "PPCBoot" disk partitions
+
+* Add support for TQM8255 Board / MPC8255 CPU
+
+======================================================================
+Changes for U-Boot 0.3.1:
+======================================================================
+
+* Make sure Block Lock Bits get cleared in R360MPI flash driver
+
+* MPC823 LCD driver: Fill color map backwards, to allow for steady
+ display when Linux takes over
+
+* Patch by Erwin Rol, 27 Feb 2003:
+ Add support for RTEMS (this time for real).
+
+* Add support for "bmp info" and "bmp display" commands to load
+ bitmap images; this can be used (for example in a "preboot"
+ command) to display a splash screen very quickly after poweron.
+
+* Add support for 133 MHz clock on INCA-IP board
+
+* Patch by Lutz Dennig, 10 Apr 2003:
+ Update for R360MPI board
+
+* Add new meaning to "autostart" environment variable:
+ If set to "no", a standalone image passed to the
+ "bootm" command will be copied to the load address
+ (and eventually uncompressed), but NOT be started.
+ This can be used to load and uncompress arbitrary
+ data.
+
+* Patch by Stefan Roese, 10 Apr 2003:
+ Changed DHCP client to use IP address from server option field #54
+ from the OFFER packet in the server option field #54 in the REQUEST
+ packet. This fixes a problem using a Windows 2000 DHCP server,
+ where the DHCP-server is not the TFTP-server.
+
+* Set max brightness for MN11236 displays on TRAB board
+
+* Add support for TQM862L modules
+
+======================================================================
+Changes for U-Boot 0.3.0:
+======================================================================
+
+* Patch by Arun Dharankar, 4 Apr 2003:
+ Add IDMA example code (tested on 8260 only)
+
+* Add support for Purple Board (MIPS64 5Kc)
+
+* Add support for MIPS64 5Kc CPUs
+
+* Fix missing setting of "loadaddr" and "bootfile" on ARM and MIPS
+
+* Patch by Denis Peter, 04 Apr 2003:
+ - update MIP405-4 board
+
* Patch by Stefan Roese, 4 Apr 2003:
- U-Boot version environment variable "ver" added
(CONFIG_VERSION_VARIABLE).
- Changed PPC405GPr version from A to B.
- Changed CPCI405 to use CTS instead of DSR on PPC405 UART1.
+* Patches by Denis Peter, 03 April 2003:
+ - fix PCI IRQs on MPL boards
+ - fix two more un-relocated pointer problems
+
+* Fix behaviour of "run" command:
+ - print error message iv variable does not exist
+ - terminate processing of arguments in case of error
+
+* Patches by Peter Figuli, 10 Mar 2003
+ - Add support for BTUART on PXA platform
+ - Add support for WEP EP250 (PXA) board
+
+* Fix flash problems on INCA-IP; add tool to allow bruning images to
+ flash using a BDI2000
+
+* Implement fix for I2C Edge Conditions problem for all boards that
+ use the bit-banging driver (common/soft_i2c.c)
+
* Patch by Martin Winistoerfer, 23 Mar 2003
- Add port to MPC555/556 microcontrollers
- Add support for cmi customer board with
* Add patches by Robert Schwebel, 31 Mar 2003:
- add ctrl-c support for kermit download
- align bdinfo output on ARM
+ - csb226 board: bring in sync with innokom/memsetup.S
+ - csb226 board: fix MDREFR handling
+ - misc doc fixes / extensions
+ - innokom board: cleanup, MDREFR fix in memsetup.S, config update
+ - add BOOT_PROGRESS to armlinux.c
* Add CPU ID, version, and clock speed for INCA-IP
* TRAB fixes / extensions:
- Restore VFD brightness as saved in environment
- - add support for FGujitsu flashes
+ - add support for Fujitsu flashes
- make sure both buzzers are turned off (drive low level)
* Patches by Robert Schwebel, 06 Mar 2003: