ARM: uniphier: enable CONFIG_CMD_CONFIG

[people/ms/u-boot.git] / README

diff --git a/README b/README
index 7e0dd35f931facaea8e826bbbb07993bcbe5304e..4f0dbd4fca6ddc94aa26e874be54231089fc79a0 100644 (file)
--- a/README
+++ b/README
@@ -504,6 +504,12 @@ The following options need to be configured:
                CONFIG_SYS_FSL_IFC_LE
                Defines the IFC controller register space as Little Endian
 
+               CONFIG_SYS_FSL_IFC_CLK_DIV
+               Defines divider of platform clock(clock input to IFC controller).
+
+               CONFIG_SYS_FSL_LBC_CLK_DIV
+               Defines divider of platform clock(clock input to eLBC controller).
+
                CONFIG_SYS_FSL_PBL_PBI
                It enables addition of RCW (Power on reset configuration) in built image.
                Please refer doc/README.pblimage for more details
@@ -1457,9 +1463,6 @@ The following options need to be configured:
                        CONFIG_SH_MMCIF_CLK
                        Define the clock frequency for MMCIF
 
-               CONFIG_GENERIC_MMC
-               Enable the generic MMC driver
-
                CONFIG_SUPPORT_EMMC_BOOT
                Enable some additional features of the eMMC boot partitions.
 
@@ -1768,12 +1771,6 @@ The following options need to be configured:
                can be displayed via the splashscreen support or the
                bmp command.
 
-- Do compressing for memory range:
-               CONFIG_CMD_ZIP
-
-               If this option is set, it would use zlib deflate method
-               to compress the specified memory at its best effort.
-
 - Compression support:
                CONFIG_GZIP
 
@@ -2033,7 +2030,7 @@ The following options need to be configured:
 
                A byte containing the id of the VLAN.
 
-- Status LED:  CONFIG_STATUS_LED
+- Status LED:  CONFIG_LED_STATUS
 
                Several configurations allow to display the current
                status using a LED. For instance, the LED will blink
@@ -2041,15 +2038,15 @@ The following options need to be configured:
                soon as a reply to a BOOTP request was received, and
                start blinking slow once the Linux kernel is running
                (supported by a status LED driver in the Linux
-               kernel). Defining CONFIG_STATUS_LED enables this
+               kernel). Defining CONFIG_LED_STATUS enables this
                feature in U-Boot.
 
                Additional options:
 
-               CONFIG_GPIO_LED
+               CONFIG_LED_STATUS_GPIO
                The status LED can be connected to a GPIO pin.
                In such cases, the gpio_led driver can be used as a
-               status LED backend implementation. Define CONFIG_GPIO_LED
+               status LED backend implementation. Define CONFIG_LED_STATUS_GPIO
                to include the gpio_led driver in the U-Boot binary.
 
                CONFIG_GPIO_LED_INVERTED_TABLE
@@ -2783,19 +2780,6 @@ The following options need to be configured:
                this is instead controlled by the value of
                /config/load-environment.
 
-- Parallel Flash support:
-               CONFIG_SYS_NO_FLASH
-
-               Traditionally U-Boot was run on systems with parallel NOR
-               flash. This option is used to disable support for parallel NOR
-               flash. This option should be defined if the board does not have
-               parallel flash.
-
-               If this option is not defined one of the generic flash drivers
-               (e.g.  CONFIG_FLASH_CFI_DRIVER or CONFIG_ST_SMI) must be
-               selected or the board must provide an implementation of the
-               flash API (see include/flash.h).
-
 - DataFlash Support:
                CONFIG_HAS_DATAFLASH