#ifndef _M68K_DMA_H
#define _M68K_DMA_H 1
-#ifdef CONFIG_COLDFIRE
-/*
- * ColdFire DMA Model:
- * ColdFire DMA supports two forms of DMA: Single and Dual address. Single
- * address mode emits a source address, and expects that the device will either
- * pick up the data (DMA READ) or source data (DMA WRITE). This implies that
- * the device will place data on the correct byte(s) of the data bus, as the
- * memory transactions are always 32 bits. This implies that only 32 bit
- * devices will find single mode transfers useful. Dual address DMA mode
- * performs two cycles: source read and destination write. ColdFire will
- * align the data so that the device will always get the correct bytes, thus
- * is useful for 8 and 16 bit devices. This is the mode that is supported
- * below.
- *
- * AUG/22/2000 : added support for 32-bit Dual-Address-Mode (K) 2000
- * Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
- *
- * AUG/25/2000 : added support for 8, 16 and 32-bit Single-Address-Mode (K)2000
- * Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
- *
- * APR/18/2002 : added proper support for MCF5272 DMA controller.
- * Arthur Shipkowski (art@videon-central.com)
- */
-
-#include <asm/coldfire.h>
-#include <asm/mcfsim.h>
-#include <asm/mcfdma.h>
-
-/*
- * Set number of channels of DMA on ColdFire for different implementations.
- */
-#if defined(CONFIG_M5249) || defined(CONFIG_M5307) || defined(CONFIG_M5407) || \
- defined(CONFIG_M523x) || defined(CONFIG_M527x) || \
- defined(CONFIG_M528x) || defined(CONFIG_M525x)
-
-#define MAX_M68K_DMA_CHANNELS 4
-#elif defined(CONFIG_M5272)
-#define MAX_M68K_DMA_CHANNELS 1
-#elif defined(CONFIG_M53xx)
-#define MAX_M68K_DMA_CHANNELS 0
-#else
-#define MAX_M68K_DMA_CHANNELS 2
-#endif
-
-extern unsigned int dma_base_addr[MAX_M68K_DMA_CHANNELS];
-extern unsigned int dma_device_address[MAX_M68K_DMA_CHANNELS];
-
-#if !defined(CONFIG_M5272)
-#define DMA_MODE_WRITE_BIT 0x01 /* Memory/IO to IO/Memory select */
-#define DMA_MODE_WORD_BIT 0x02 /* 8 or 16 bit transfers */
-#define DMA_MODE_LONG_BIT 0x04 /* or 32 bit transfers */
-#define DMA_MODE_SINGLE_BIT 0x08 /* single-address-mode */
-
-/* I/O to memory, 8 bits, mode */
-#define DMA_MODE_READ 0
-/* memory to I/O, 8 bits, mode */
-#define DMA_MODE_WRITE 1
-/* I/O to memory, 16 bits, mode */
-#define DMA_MODE_READ_WORD 2
-/* memory to I/O, 16 bits, mode */
-#define DMA_MODE_WRITE_WORD 3
-/* I/O to memory, 32 bits, mode */
-#define DMA_MODE_READ_LONG 4
-/* memory to I/O, 32 bits, mode */
-#define DMA_MODE_WRITE_LONG 5
-/* I/O to memory, 8 bits, single-address-mode */
-#define DMA_MODE_READ_SINGLE 8
-/* memory to I/O, 8 bits, single-address-mode */
-#define DMA_MODE_WRITE_SINGLE 9
-/* I/O to memory, 16 bits, single-address-mode */
-#define DMA_MODE_READ_WORD_SINGLE 10
-/* memory to I/O, 16 bits, single-address-mode */
-#define DMA_MODE_WRITE_WORD_SINGLE 11
-/* I/O to memory, 32 bits, single-address-mode */
-#define DMA_MODE_READ_LONG_SINGLE 12
-/* memory to I/O, 32 bits, single-address-mode */
-#define DMA_MODE_WRITE_LONG_SINGLE 13
-
-#else /* CONFIG_M5272 is defined */
-
-/* Source static-address mode */
-#define DMA_MODE_SRC_SA_BIT 0x01
-/* Two bits to select between all four modes */
-#define DMA_MODE_SSIZE_MASK 0x06
-/* Offset to shift bits in */
-#define DMA_MODE_SSIZE_OFF 0x01
-/* Destination static-address mode */
-#define DMA_MODE_DES_SA_BIT 0x10
-/* Two bits to select between all four modes */
-#define DMA_MODE_DSIZE_MASK 0x60
-/* Offset to shift bits in */
-#define DMA_MODE_DSIZE_OFF 0x05
-/* Size modifiers */
-#define DMA_MODE_SIZE_LONG 0x00
-#define DMA_MODE_SIZE_BYTE 0x01
-#define DMA_MODE_SIZE_WORD 0x02
-#define DMA_MODE_SIZE_LINE 0x03
-
-/*
- * Aliases to help speed quick ports; these may be suboptimal, however. They
- * do not include the SINGLE mode modifiers since the MCF5272 does not have a
- * mode where the device is in control of its addressing.
- */
-
-/* I/O to memory, 8 bits, mode */
-#define DMA_MODE_READ ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
-/* memory to I/O, 8 bits, mode */
-#define DMA_MODE_WRITE ((DMA_MODE_SIZE_BYTE << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_BYTE << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
-/* I/O to memory, 16 bits, mode */
-#define DMA_MODE_READ_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
-/* memory to I/O, 16 bits, mode */
-#define DMA_MODE_WRITE_WORD ((DMA_MODE_SIZE_WORD << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_WORD << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
-/* I/O to memory, 32 bits, mode */
-#define DMA_MODE_READ_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_SRC_SA_BIT)
-/* memory to I/O, 32 bits, mode */
-#define DMA_MODE_WRITE_LONG ((DMA_MODE_SIZE_LONG << DMA_MODE_DSIZE_OFF) | (DMA_MODE_SIZE_LONG << DMA_MODE_SSIZE_OFF) | DMA_DES_SA_BIT)
-
-#endif /* !defined(CONFIG_M5272) */
-
-#if !defined(CONFIG_M5272)
-/* enable/disable a specific DMA channel */
-static __inline__ void enable_dma(unsigned int dmanr)
-{
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("enable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmawp[MCFDMA_DCR] |= MCFDMA_DCR_EEXT;
-}
-
-static __inline__ void disable_dma(unsigned int dmanr)
-{
- volatile unsigned short *dmawp;
- volatile unsigned char *dmapb;
-
-#ifdef DMA_DEBUG
- printk("disable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmapb = (unsigned char *) dma_base_addr[dmanr];
-
- /* Turn off external requests, and stop any DMA in progress */
- dmawp[MCFDMA_DCR] &= ~MCFDMA_DCR_EEXT;
- dmapb[MCFDMA_DSR] = MCFDMA_DSR_DONE;
-}
-
-/*
- * Clear the 'DMA Pointer Flip Flop'.
- * Write 0 for LSB/MSB, 1 for MSB/LSB access.
- * Use this once to initialize the FF to a known state.
- * After that, keep track of it. :-)
- * --- In order to do that, the DMA routines below should ---
- * --- only be used while interrupts are disabled! ---
- *
- * This is a NOP for ColdFire. Provide a stub for compatibility.
- */
-static __inline__ void clear_dma_ff(unsigned int dmanr)
-{
-}
-
-/* set mode (above) for a specific DMA channel */
-static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
-{
-
- volatile unsigned char *dmabp;
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode);
-#endif
-
- dmabp = (unsigned char *) dma_base_addr[dmanr];
- dmawp = (unsigned short *) dma_base_addr[dmanr];
-
- /* Clear config errors */
- dmabp[MCFDMA_DSR] = MCFDMA_DSR_DONE;
-
- /* Set command register */
- dmawp[MCFDMA_DCR] =
- MCFDMA_DCR_INT | /* Enable completion irq */
- MCFDMA_DCR_CS | /* Force one xfer per request */
- MCFDMA_DCR_AA | /* Enable auto alignment */
- /* single-address-mode */
- ((mode & DMA_MODE_SINGLE_BIT) ? MCFDMA_DCR_SAA : 0) |
- /* sets s_rw (-> r/w) high if Memory to I/0 */
- ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_S_RW : 0) |
- /* Memory to I/O or I/O to Memory */
- ((mode & DMA_MODE_WRITE_BIT) ? MCFDMA_DCR_SINC : MCFDMA_DCR_DINC) |
- /* 32 bit, 16 bit or 8 bit transfers */
- ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_SSIZE_WORD :
- ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_SSIZE_LONG :
- MCFDMA_DCR_SSIZE_BYTE)) |
- ((mode & DMA_MODE_WORD_BIT) ? MCFDMA_DCR_DSIZE_WORD :
- ((mode & DMA_MODE_LONG_BIT) ? MCFDMA_DCR_DSIZE_LONG :
- MCFDMA_DCR_DSIZE_BYTE));
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DSR[%x]=%x DCR[%x]=%x\n", __FILE__, __LINE__,
- dmanr, (int) &dmabp[MCFDMA_DSR], dmabp[MCFDMA_DSR],
- (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR]);
-#endif
-}
-
-/* Set transfer address for specific DMA channel */
-static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
-{
- volatile unsigned short *dmawp;
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmalp = (unsigned int *) dma_base_addr[dmanr];
-
- /* Determine which address registers are used for memory/device accesses */
- if (dmawp[MCFDMA_DCR] & MCFDMA_DCR_SINC) {
- /* Source incrementing, must be memory */
- dmalp[MCFDMA_SAR] = a;
- /* Set dest address, must be device */
- dmalp[MCFDMA_DAR] = dma_device_address[dmanr];
- } else {
- /* Destination incrementing, must be memory */
- dmalp[MCFDMA_DAR] = a;
- /* Set source address, must be device */
- dmalp[MCFDMA_SAR] = dma_device_address[dmanr];
- }
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DCR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n",
- __FILE__, __LINE__, dmanr, (int) &dmawp[MCFDMA_DCR], dmawp[MCFDMA_DCR],
- (int) &dmalp[MCFDMA_SAR], dmalp[MCFDMA_SAR],
- (int) &dmalp[MCFDMA_DAR], dmalp[MCFDMA_DAR]);
-#endif
-}
-
-/*
- * Specific for Coldfire - sets device address.
- * Should be called after the mode set call, and before set DMA address.
- */
-static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a)
-{
-#ifdef DMA_DEBUG
- printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dma_device_address[dmanr] = a;
-}
-
-/*
- * NOTE 2: "count" represents _bytes_.
- */
-static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
-{
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- dmawp[MCFDMA_BCR] = (unsigned short)count;
-}
-
-/*
- * Get DMA residue count. After a DMA transfer, this
- * should return zero. Reading this while a DMA transfer is
- * still in progress will return unpredictable results.
- * Otherwise, it returns the number of _bytes_ left to transfer.
- */
-static __inline__ int get_dma_residue(unsigned int dmanr)
-{
- volatile unsigned short *dmawp;
- unsigned short count;
-
-#ifdef DMA_DEBUG
- printk("get_dma_residue(dmanr=%d)\n", dmanr);
-#endif
-
- dmawp = (unsigned short *) dma_base_addr[dmanr];
- count = dmawp[MCFDMA_BCR];
- return((int) count);
-}
-#else /* CONFIG_M5272 is defined */
-
-/*
- * The MCF5272 DMA controller is very different than the controller defined above
- * in terms of register mapping. For instance, with the exception of the 16-bit
- * interrupt register (IRQ#85, for reference), all of the registers are 32-bit.
- *
- * The big difference, however, is the lack of device-requested DMA. All modes
- * are dual address transfer, and there is no 'device' setup or direction bit.
- * You can DMA between a device and memory, between memory and memory, or even between
- * two devices directly, with any combination of incrementing and non-incrementing
- * addresses you choose. This puts a crimp in distinguishing between the 'device
- * address' set up by set_dma_device_addr.
- *
- * Therefore, there are two options. One is to use set_dma_addr and set_dma_device_addr,
- * which will act exactly as above in -- it will look to see if the source is set to
- * autoincrement, and if so it will make the source use the set_dma_addr value and the
- * destination the set_dma_device_addr value. Otherwise the source will be set to the
- * set_dma_device_addr value and the destination will get the set_dma_addr value.
- *
- * The other is to use the provided set_dma_src_addr and set_dma_dest_addr functions
- * and make it explicit. Depending on what you're doing, one of these two should work
- * for you, but don't mix them in the same transfer setup.
- */
-
-/* enable/disable a specific DMA channel */
-static __inline__ void enable_dma(unsigned int dmanr)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("enable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- dmalp[MCFDMA_DMR] |= MCFDMA_DMR_EN;
-}
-
-static __inline__ void disable_dma(unsigned int dmanr)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("disable_dma(dmanr=%d)\n", dmanr);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
-
- /* Turn off external requests, and stop any DMA in progress */
- dmalp[MCFDMA_DMR] &= ~MCFDMA_DMR_EN;
- dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET;
-}
-
-/*
- * Clear the 'DMA Pointer Flip Flop'.
- * Write 0 for LSB/MSB, 1 for MSB/LSB access.
- * Use this once to initialize the FF to a known state.
- * After that, keep track of it. :-)
- * --- In order to do that, the DMA routines below should ---
- * --- only be used while interrupts are disabled! ---
- *
- * This is a NOP for ColdFire. Provide a stub for compatibility.
- */
-static __inline__ void clear_dma_ff(unsigned int dmanr)
-{
-}
-
-/* set mode (above) for a specific DMA channel */
-static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
-{
-
- volatile unsigned int *dmalp;
- volatile unsigned short *dmawp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_mode(dmanr=%d,mode=%d)\n", dmanr, mode);
-#endif
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- dmawp = (unsigned short *) dma_base_addr[dmanr];
-
- /* Clear config errors */
- dmalp[MCFDMA_DMR] |= MCFDMA_DMR_RESET;
-
- /* Set command register */
- dmalp[MCFDMA_DMR] =
- MCFDMA_DMR_RQM_DUAL | /* Mandatory Request Mode setting */
- MCFDMA_DMR_DSTT_SD | /* Set up addressing types; set to supervisor-data. */
- MCFDMA_DMR_SRCT_SD | /* Set up addressing types; set to supervisor-data. */
- /* source static-address-mode */
- ((mode & DMA_MODE_SRC_SA_BIT) ? MCFDMA_DMR_SRCM_SA : MCFDMA_DMR_SRCM_IA) |
- /* dest static-address-mode */
- ((mode & DMA_MODE_DES_SA_BIT) ? MCFDMA_DMR_DSTM_SA : MCFDMA_DMR_DSTM_IA) |
- /* burst, 32 bit, 16 bit or 8 bit transfers are separately configurable on the MCF5272 */
- (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_DSTS_OFF) |
- (((mode & DMA_MODE_SSIZE_MASK) >> DMA_MODE_SSIZE_OFF) << MCFDMA_DMR_SRCS_OFF);
-
- dmawp[MCFDMA_DIR] |= MCFDMA_DIR_ASCEN; /* Enable completion interrupts */
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DMR[%x]=%x DIR[%x]=%x\n", __FILE__, __LINE__,
- dmanr, (int) &dmalp[MCFDMA_DMR], dmalp[MCFDMA_DMR],
- (int) &dmawp[MCFDMA_DIR], dmawp[MCFDMA_DIR]);
-#endif
-}
-
-/* Set transfer address for specific DMA channel */
-static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
-
- /* Determine which address registers are used for memory/device accesses */
- if (dmalp[MCFDMA_DMR] & MCFDMA_DMR_SRCM) {
- /* Source incrementing, must be memory */
- dmalp[MCFDMA_DSAR] = a;
- /* Set dest address, must be device */
- dmalp[MCFDMA_DDAR] = dma_device_address[dmanr];
- } else {
- /* Destination incrementing, must be memory */
- dmalp[MCFDMA_DDAR] = a;
- /* Set source address, must be device */
- dmalp[MCFDMA_DSAR] = dma_device_address[dmanr];
- }
-
-#ifdef DEBUG_DMA
- printk("%s(%d): dmanr=%d DMR[%x]=%x SAR[%x]=%08x DAR[%x]=%08x\n",
- __FILE__, __LINE__, dmanr, (int) &dmalp[MCFDMA_DMR], dmalp[MCFDMA_DMR],
- (int) &dmalp[MCFDMA_DSAR], dmalp[MCFDMA_DSAR],
- (int) &dmalp[MCFDMA_DDAR], dmalp[MCFDMA_DDAR]);
-#endif
-}
-
-/*
- * Specific for Coldfire - sets device address.
- * Should be called after the mode set call, and before set DMA address.
- */
-static __inline__ void set_dma_device_addr(unsigned int dmanr, unsigned int a)
-{
-#ifdef DMA_DEBUG
- printk("set_dma_device_addr(dmanr=%d,a=%x)\n", dmanr, a);
-#endif
-
- dma_device_address[dmanr] = a;
-}
-
-/*
- * NOTE 2: "count" represents _bytes_.
- *
- * NOTE 3: While a 32-bit register, "count" is only a maximum 24-bit value.
- */
-static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
-{
- volatile unsigned int *dmalp;
-
-#ifdef DMA_DEBUG
- printk("set_dma_count(dmanr=%d,count=%d)\n", dmanr, count);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- dmalp[MCFDMA_DBCR] = count;
-}
-
-/*
- * Get DMA residue count. After a DMA transfer, this
- * should return zero. Reading this while a DMA transfer is
- * still in progress will return unpredictable results.
- * Otherwise, it returns the number of _bytes_ left to transfer.
- */
-static __inline__ int get_dma_residue(unsigned int dmanr)
-{
- volatile unsigned int *dmalp;
- unsigned int count;
-
-#ifdef DMA_DEBUG
- printk("get_dma_residue(dmanr=%d)\n", dmanr);
-#endif
-
- dmalp = (unsigned int *) dma_base_addr[dmanr];
- count = dmalp[MCFDMA_DBCR];
- return(count);
-}
-
-#endif /* !defined(CONFIG_M5272) */
-#endif /* CONFIG_COLDFIRE */
-
/* it's useless on the m68k, but unfortunately needed by the new
bootmem allocator (but this should do it for this) */
#define MAX_DMA_ADDRESS PAGE_OFFSET
-#define MAX_DMA_CHANNELS 8
-
-extern int request_dma(unsigned int dmanr, const char * device_id); /* reserve a DMA channel */
-extern void free_dma(unsigned int dmanr); /* release it again */
-
#ifdef CONFIG_PCI
extern int isa_dma_bridge_buggy;
#else
projects / people / ms / linux.git / blobdiff