config MACH_SUN6I
bool "sun6i (Allwinner A31)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN7I
bool "sun7i (Allwinner A20)"
config MACH_SUN8I_A23
bool "sun8i (Allwinner A23)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN8I_A33
bool "sun8i (Allwinner A33)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
+config MACH_SUN9I
+ bool "sun9i (Allwinner A80)"
+ select CPU_V7
+ select SUNXI_GEN_SUN6I
endchoice
---help---
Set the dram zq value.
+config DRAM_ODT_EN
+ bool "sunxi dram odt enable"
+ default n if !MACH_SUN8I_A23
+ default y if MACH_SUN8I_A23
+ ---help---
+ Select this to enable dram odt (on die termination).
+
if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
config DRAM_EMR1
int "sunxi dram emr1 value"
---help---
Set the dram controller emr1 value.
-config DRAM_ODT_EN
- int "sunxi dram odt_en value"
- default 0
- ---help---
- Set the dram controller odt_en parameter. This can be used to
- enable/disable the ODT feature.
-
config DRAM_TPR3
hex "sunxi dram tpr3 value"
default 0
endif
+if MACH_SUN8I_A23
+config DRAM_ODT_CORRECTION
+ int "sunxi dram odt correction value"
+ default 0
+ ---help---
+ Set the dram odt correction value (range -255 - 255). In allwinner
+ fex files, this option is found in bits 8-15 of the u32 odt_en variable
+ in the [dram] section. When bit 31 of the odt_en variable is set
+ then the correction is negative. Usually the value for this is 0.
+endif
+
config SYS_CLK_FREQ
default 912000000 if MACH_SUN7I
default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
default "sun6i" if MACH_SUN6I
default "sun7i" if MACH_SUN7I
default "sun8i" if MACH_SUN8I
+ default "sun9i" if MACH_SUN9I
config SYS_BOARD
default "sunxi"
config SYS_SOC
default "sunxi"
-config SPL_FEL
- bool "SPL/FEL mode support"
- depends on SPL
- default n
- help
- This enables support for Fast Early Loader (FEL) mode. This
- allows U-Boot to be loaded to the board over USB by the on-chip
- boot rom. U-Boot should be sent in two parts: SPL first, with
- 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
- 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
- shrinks the amount of SRAM available to SPL, so only enable it if
- you need FEL. Note that enabling this option only allows FEL to be
- used; it is still possible to boot U-Boot from boot media. U-Boot
- SPL detects when it is being loaded using FEL.
-
config UART0_PORT_F
bool "UART0 on MicroSD breakout board"
- depends on SPL_FEL
default n
---help---
Repurpose the SD card slot for getting access to the UART0 serial
slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
support for this.
+config SPL_NAND_SUPPORT
+ bool "SPL/NAND mode support"
+ depends on SPL
+ default n
+ ---help---
+ This enables support for booting from NAND internal
+ memory. U-Boot SPL doesn't detect where is it load from,
+ therefore this option is needed to properly load image from
+ flash. Option also disables MMC functionality on U-Boot due to
+ initialization errors encountered, when both controllers are
+ enabled.
+
config USB0_VBUS_PIN
string "Vbus enable pin for usb0 (otg)"
default ""
config SYS_MALLOC_CLEAR_ON_INIT
default n
-config NET
- default y
-
config NETDEVICES
default y