choice
prompt "Sunxi SoC Variant"
+ optional
config MACH_SUN4I
bool "sun4i (Allwinner A10)"
config MACH_SUN6I
bool "sun6i (Allwinner A31)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN7I
bool "sun7i (Allwinner A20)"
config MACH_SUN8I_A23
bool "sun8i (Allwinner A23)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
config MACH_SUN8I_A33
bool "sun8i (Allwinner A33)"
select CPU_V7
+ select CPU_V7_HAS_NONSEC
+ select CPU_V7_HAS_VIRT
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
+
+config MACH_SUN9I
+ bool "sun9i (Allwinner A80)"
+ select CPU_V7
+ select SUNXI_GEN_SUN6I
endchoice
---help---
Set the dram zq value.
+config DRAM_ODT_EN
+ bool "sunxi dram odt enable"
+ default n if !MACH_SUN8I_A23
+ default y if MACH_SUN8I_A23
+ ---help---
+ Select this to enable dram odt (on die termination).
+
if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
config DRAM_EMR1
int "sunxi dram emr1 value"
---help---
Set the dram controller emr1 value.
-config DRAM_ODT_EN
- int "sunxi dram odt_en value"
- default 0
- ---help---
- Set the dram controller odt_en parameter. This can be used to
- enable/disable the ODT feature.
-
config DRAM_TPR3
hex "sunxi dram tpr3 value"
default 0
endif
+if MACH_SUN8I_A23
+config DRAM_ODT_CORRECTION
+ int "sunxi dram odt correction value"
+ default 0
+ ---help---
+ Set the dram odt correction value (range -255 - 255). In allwinner
+ fex files, this option is found in bits 8-15 of the u32 odt_en variable
+ in the [dram] section. When bit 31 of the odt_en variable is set
+ then the correction is negative. Usually the value for this is 0.
+endif
+
config SYS_CLK_FREQ
default 912000000 if MACH_SUN7I
default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
default "sun6i" if MACH_SUN6I
default "sun7i" if MACH_SUN7I
default "sun8i" if MACH_SUN8I
+ default "sun9i" if MACH_SUN9I
config SYS_BOARD
default "sunxi"
config SYS_SOC
default "sunxi"
-config SPL_FEL
- bool "SPL/FEL mode support"
- depends on SPL
- default n
- help
- This enables support for Fast Early Loader (FEL) mode. This
- allows U-Boot to be loaded to the board over USB by the on-chip
- boot rom. U-Boot should be sent in two parts: SPL first, with
- 'fel write 0x2000 u-boot-spl.bin; fel exe 0x2000' then U-Boot with
- 'fel write 0x4a000000 u-boot.bin; fel exe 0x4a000000'. This option
- shrinks the amount of SRAM available to SPL, so only enable it if
- you need FEL. Note that enabling this option only allows FEL to be
- used; it is still possible to boot U-Boot from boot media. U-Boot
- SPL detects when it is being loaded using FEL.
-
config UART0_PORT_F
bool "UART0 on MicroSD breakout board"
- depends on SPL_FEL
default n
---help---
Repurpose the SD card slot for getting access to the UART0 serial
at the same time, the system can be only booted in the FEL mode.
Only enable this if you really know what you are doing.
-config FDTFILE
- string "Default fdtfile env setting for this board"
-
config OLD_SUNXI_KERNEL_COMPAT
boolean "Enable workarounds for booting old kernels"
default n
slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
support for this.
+config SPL_NAND_SUPPORT
+ bool "SPL/NAND mode support"
+ depends on SPL
+ default n
+ ---help---
+ This enables support for booting from NAND internal
+ memory. U-Boot SPL doesn't detect where is it load from,
+ therefore this option is needed to properly load image from
+ flash. Option also disables MMC functionality on U-Boot due to
+ initialization errors encountered, when both controllers are
+ enabled.
+
config USB0_VBUS_PIN
string "Vbus enable pin for usb0 (otg)"
default ""
---help---
Set the GMAC Transmit Clock Delay Chain value.
+config SYS_MALLOC_CLEAR_ON_INIT
+ default n
+
+config NETDEVICES
+ default y
+
+config DM_ETH
+ default y
+
+config DM_SERIAL
+ default y
+
+config DM_USB
+ default y if !USB_MUSB_SUNXI
+
endif