29,916,167 26,005,792 bootm_start
30,361,327 445,160 start_kernel
-config BOOTSTAGE_USER_COUNT
- int "Number of boot ID numbers available for user use"
- default 20
- help
- This is the number of available user bootstage records.
- Each time you call bootstage_mark(BOOTSTAGE_ID_ALLOC, ...)
- a new ID will be allocated from this stash. If you exceed
- the limit, recording will stop.
-
config BOOTSTAGE_RECORD_COUNT
int "Number of boot stage records to store"
default 30
This is the size of the bootstage record list and is the maximum
number of bootstage records that can be recorded.
+config SPL_BOOTSTAGE_RECORD_COUNT
+ int "Number of boot stage records to store for SPL"
+ default 5
+ help
+ This is the size of the bootstage record list and is the maximum
+ number of bootstage records that can be recorded.
+
config BOOTSTAGE_FDT
bool "Store boot timing information in the OS device tree"
depends on BOOTSTAGE
CONFIG_BOOTARGS goes into the environment value "bootargs". Note that
this value will also override the "chosen" node in FDT blob.
+config USE_BOOTCOMMAND
+ bool "Enable a default value for bootcmd"
+ help
+ Provide a default value for the bootcmd entry in the environment. If
+ autoboot is enabled this is what will be run automatically. Enable
+ this option to be able to specify CONFIG_BOOTCOMMAND as a string. If
+ this option is disabled, CONFIG_BOOTCOMMAND will be undefined and
+ won't take any space in U-Boot image.
+
+config BOOTCOMMAND
+ string "bootcmd value"
+ depends on USE_BOOTCOMMAND
+ default "run distro_bootcmd" if DISTRO_DEFAULTS
+ help
+ This is the string of commands that will be used as bootcmd and if
+ AUTOBOOT is set, automatically run.
+
menu "Console"
config MENU
help
This options adds the board specific name to u-boot version.
+config LOGLEVEL
+ int "loglevel"
+ default 4
+ range 0 8
+ help
+ All Messages with a loglevel smaller than the console loglevel will
+ be compiled in. The loglevels are defined as follows:
+
+ 0 (KERN_EMERG) system is unusable
+ 1 (KERN_ALERT) action must be taken immediately
+ 2 (KERN_CRIT) critical conditions
+ 3 (KERN_ERR) error conditions
+ 4 (KERN_WARNING) warning conditions
+ 5 (KERN_NOTICE) normal but significant condition
+ 6 (KERN_INFO) informational
+ 7 (KERN_DEBUG) debug-level messages
+
+config SPL_LOGLEVEL
+ int
+ default LOGLEVEL
+
config SILENT_CONSOLE
bool "Support a silent console"
help
endmenu
-config DTB_RESELECT
- bool "Support swapping dtbs at a later point in boot"
- depends on FIT_EMBED
- help
- It is possible during initial boot you may need to use a generic
- dtb until you can fully determine the board your running on. This
- config allows boards to implement a function at a later point
- during boot to switch to the "correct" dtb.
+menu "Logging"
+
+config LOG
+ bool "Enable logging support"
+ help
+ This enables support for logging of status and debug messages. These
+ can be displayed on the console, recorded in a memory buffer, or
+ discarded if not needed. Logging supports various categories and
+ levels of severity.
+
+config SPL_LOG
+ bool "Enable logging support in SPL"
+ help
+ This enables support for logging of status and debug messages. These
+ can be displayed on the console, recorded in a memory buffer, or
+ discarded if not needed. Logging supports various categories and
+ levels of severity.
+
+config LOG_MAX_LEVEL
+ int "Maximum log level to record"
+ depends on LOG
+ default 5
+ help
+ This selects the maximum log level that will be recorded. Any value
+ higher than this will be ignored. If possible log statements below
+ this level will be discarded at build time. Levels:
+
+ 0 - panic
+ 1 - critical
+ 2 - error
+ 3 - warning
+ 4 - note
+ 5 - info
+ 6 - detail
+ 7 - debug
+
+config SPL_LOG_MAX_LEVEL
+ int "Maximum log level to record in SPL"
+ depends on SPL_LOG
+ default 3
+ help
+ This selects the maximum log level that will be recorded. Any value
+ higher than this will be ignored. If possible log statements below
+ this level will be discarded at build time. Levels:
+
+ 0 - panic
+ 1 - critical
+ 2 - error
+ 3 - warning
+ 4 - note
+ 5 - info
+ 6 - detail
+ 7 - debug
+
+config LOG_CONSOLE
+ bool "Allow log output to the console"
+ depends on LOG
+ default y
+ help
+ Enables a log driver which writes log records to the console.
+ Generally the console is the serial port or LCD display. Only the
+ log message is shown - other details like level, category, file and
+ line number are omitted.
+
+config LOG_SPL_CONSOLE
+ bool "Allow log output to the console in SPL"
+ depends on LOG_SPL
+ default y
+ help
+ Enables a log driver which writes log records to the console.
+ Generally the console is the serial port or LCD display. Only the
+ log message is shown - other details like level, category, file and
+ line number are omitted.
+
+config LOG_TEST
+ bool "Provide a test for logging"
+ depends on LOG
+ default y if SANDBOX
+ help
+ This enables a 'log test' command to test logging. It is normally
+ executed from a pytest and simply outputs logging information
+ in various different ways to test that the logging system works
+ correctly with varoius settings.
-config FIT_EMBED
- bool "Support a FIT image embedded in the U-boot image"
- help
- This option provides hooks to allow U-boot to parse an
- appended FIT image and enable board specific code to then select
- the correct DTB to be used.
+endmenu
config DEFAULT_FDT_FILE
string "Default fdt file"