CONFIG_BOOTARGS goes into the environment value "bootargs". Note that
this value will also override the "chosen" node in FDT blob.
+config USE_BOOTCOMMAND
+ bool "Enable a default value for bootcmd"
+ help
+ Provide a default value for the bootcmd entry in the environment. If
+ autoboot is enabled this is what will be run automatically. Enable
+ this option to be able to specify CONFIG_BOOTCOMMAND as a string. If
+ this option is disabled, CONFIG_BOOTCOMMAND will be undefined and
+ won't take any space in U-Boot image.
+
+config BOOTCOMMAND
+ string "bootcmd value"
+ depends on USE_BOOTCOMMAND
+ default "run distro_bootcmd" if DISTRO_DEFAULTS
+ help
+ This is the string of commands that will be used as bootcmd and if
+ AUTOBOOT is set, automatically run.
+
menu "Console"
config MENU
help
This options adds the board specific name to u-boot version.
+config LOGLEVEL
+ int "loglevel"
+ default 4
+ range 0 8
+ help
+ All Messages with a loglevel smaller than the console loglevel will
+ be compiled in. The loglevels are defined as follows:
+
+ 0 (KERN_EMERG) system is unusable
+ 1 (KERN_ALERT) action must be taken immediately
+ 2 (KERN_CRIT) critical conditions
+ 3 (KERN_ERR) error conditions
+ 4 (KERN_WARNING) warning conditions
+ 5 (KERN_NOTICE) normal but significant condition
+ 6 (KERN_INFO) informational
+ 7 (KERN_DEBUG) debug-level messages
+
+config SPL_LOGLEVEL
+ int
+ default LOGLEVEL
+
config SILENT_CONSOLE
bool "Support a silent console"
help
endmenu
-config DTB_RESELECT
- bool "Support swapping dtbs at a later point in boot"
- depends on FIT_EMBED
+menu "Logging"
+
+config LOG
+ bool "Enable logging support"
help
- It is possible during initial boot you may need to use a generic
- dtb until you can fully determine the board your running on. This
- config allows boards to implement a function at a later point
- during boot to switch to the "correct" dtb.
+ This enables support for logging of status and debug messages. These
+ can be displayed on the console, recorded in a memory buffer, or
+ discarded if not needed. Logging supports various categories and
+ levels of severity.
-config FIT_EMBED
- bool "Support a FIT image embedded in the U-boot image"
+config SPL_LOG
+ bool "Enable logging support in SPL"
help
- This option provides hooks to allow U-boot to parse an
- appended FIT image and enable board specific code to then select
- the correct DTB to be used.
+ This enables support for logging of status and debug messages. These
+ can be displayed on the console, recorded in a memory buffer, or
+ discarded if not needed. Logging supports various categories and
+ levels of severity.
+
+config LOG_MAX_LEVEL
+ int "Maximum log level to record"
+ depends on LOG
+ default 5
+ help
+ This selects the maximum log level that will be recorded. Any value
+ higher than this will be ignored. If possible log statements below
+ this level will be discarded at build time. Levels:
+
+ 0 - panic
+ 1 - critical
+ 2 - error
+ 3 - warning
+ 4 - note
+ 5 - info
+ 6 - detail
+ 7 - debug
+
+config SPL_LOG_MAX_LEVEL
+ int "Maximum log level to record in SPL"
+ depends on SPL_LOG
+ default 3
+ help
+ This selects the maximum log level that will be recorded. Any value
+ higher than this will be ignored. If possible log statements below
+ this level will be discarded at build time. Levels:
+
+ 0 - panic
+ 1 - critical
+ 2 - error
+ 3 - warning
+ 4 - note
+ 5 - info
+ 6 - detail
+ 7 - debug
+
+config LOG_CONSOLE
+ bool "Allow log output to the console"
+ depends on LOG
+ default y
+ help
+ Enables a log driver which writes log records to the console.
+ Generally the console is the serial port or LCD display. Only the
+ log message is shown - other details like level, category, file and
+ line number are omitted.
+
+config LOG_SPL_CONSOLE
+ bool "Allow log output to the console in SPL"
+ depends on LOG_SPL
+ default y
+ help
+ Enables a log driver which writes log records to the console.
+ Generally the console is the serial port or LCD display. Only the
+ log message is shown - other details like level, category, file and
+ line number are omitted.
+
+config LOG_TEST
+ bool "Provide a test for logging"
+ depends on LOG
+ default y if SANDBOX
+ help
+ This enables a 'log test' command to test logging. It is normally
+ executed from a pytest and simply outputs logging information
+ in various different ways to test that the logging system works
+ correctly with varoius settings.
+
+endmenu
config DEFAULT_FDT_FILE
string "Default fdt file"
projects / people / ms / u-boot.git / blobdiff