menu "Environment"
+config ENV_IS_IN_DATAFLASH
+ bool "Environment in dataflash"
+ depends on !CHAIN_OF_TRUST
+ help
+ Define this if you have a DataFlash memory device which you
+ want to use for the environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These three #defines specify the offset and size of the
+ environment area within the total memory of your DataFlash placed
+ at the specified address.
+
+config ENV_IS_IN_EEPROM
+ bool "Environment in EEPROM"
+ depends on !CHAIN_OF_TRUST
+ help
+ Use this if you have an EEPROM or similar serial access
+ device and a driver for it.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the total memory of your EEPROM.
+
+ - CONFIG_SYS_I2C_EEPROM_ADDR:
+ If defined, specified the chip address of the EEPROM device.
+ The default address is zero.
+
+ - CONFIG_SYS_I2C_EEPROM_BUS:
+ If defined, specified the i2c bus of the EEPROM device.
+
+ - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
+ If defined, the number of bits used to address bytes in a
+ single page in the EEPROM device. A 64 byte page, for example
+ would require six bits.
+
+ - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
+ If defined, the number of milliseconds to delay between
+ page writes. The default is zero milliseconds.
+
+ - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
+ The length in bytes of the EEPROM memory array address. Note
+ that this is NOT the chip address length!
+
+ - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
+ EEPROM chips that implement "address overflow" are ones
+ like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+ address and the extra bits end up in the "chip address" bit
+ slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+ byte chips.
+
+ Note that we consider the length of the address field to
+ still be one byte because the extra address bits are hidden
+ in the chip address.
+
+ - CONFIG_SYS_EEPROM_SIZE:
+ The size in bytes of the EEPROM device.
+
+ - CONFIG_ENV_EEPROM_IS_ON_I2C
+ define this, if you have I2C and SPI activated, and your
+ EEPROM, which holds the environment, is on the I2C bus.
+
+ - CONFIG_I2C_ENV_EEPROM_BUS
+ if you have an Environment on an EEPROM reached over
+ I2C muxes, you can define here, how to reach this
+ EEPROM. For example:
+
+ #define CONFIG_I2C_ENV_EEPROM_BUS 1
+
+ EEPROM which holds the environment, is reached over
+ a pca9547 i2c mux with address 0x70, channel 3.
+
+config ENV_IS_IN_FAT
+ bool "Environment is in a FAT filesystem"
+ depends on !CHAIN_OF_TRUST
+ help
+ Define this if you want to use the FAT file system for the environment.
+
+ - FAT_ENV_INTERFACE:
+
+ Define this to a string that is the name of the block device.
+
+ - FAT_ENV_DEVICE_AND_PART:
+
+ Define this to a string to specify the partition of the device. It can
+ be as following:
+
+ "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
+ - "D:P": device D partition P. Error occurs if device D has no
+ partition table.
+ - "D:0": device D.
+ - "D" or "D:": device D partition 1 if device D has partition
+ table, or the whole device D if has no partition
+ table.
+ - "D:auto": first partition in device D with bootable flag set.
+ If none, first valid partition in device D. If no
+ partition table then means device D.
+
+ - FAT_ENV_FILE:
+
+ It's a string of the FAT file name. This file use to store the
+ environment.
+
+ - CONFIG_FAT_WRITE:
+ This must be enabled. Otherwise it cannot save the environment file.
+
config ENV_IS_IN_FLASH
bool "Environment in flash memory"
depends on !CHAIN_OF_TRUST
can just be read and written to, without any special
provision.
+config ENV_IS_IN_ONENAND
+ bool "Environment is in OneNAND"
+ depends on !CHAIN_OF_TRUST
+ help
+ Define this if you want to put your local device's environment in
+ OneNAND.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines are used to determine the device range you
+ want to use for environment. It is assumed that this memory
+ can just be read and written to, without any special
+ provision.
+
+config ENV_IS_IN_REMOTE
+ bool "Environment is in remove memory space"
+ depends on !CHAIN_OF_TRUST
+ help
+ Define this if you have a remote memory space which you
+ want to use for the local device's environment.
+
+ - CONFIG_ENV_ADDR:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the address and size of the
+ environment area within the remote memory space. The
+ local device can get the environment from remote memory
+ space by SRIO or PCIE links.
+
+config ENV_IS_IN_SPI_FLASH
+ bool "Environment is in SPI flash"
+ depends on !CHAIN_OF_TRUST
+ help
+ Define this if you have a SPI Flash memory device which you
+ want to use for the environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SECT_SIZE:
+
+ Define the SPI flash's sector size.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ This setting describes a second storage area of CONFIG_ENV_SIZE
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_REDUND must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SPI_BUS (optional):
+ - CONFIG_ENV_SPI_CS (optional):
+
+ Define the SPI bus and chip select. If not defined they will be 0.
+
+ - CONFIG_ENV_SPI_MAX_HZ (optional):
+
+ Define the SPI max work clock. If not defined then use 1MHz.
+
+ - CONFIG_ENV_SPI_MODE (optional):
+
+ Define the SPI work mode. If not defined then use SPI_MODE_3.
+
config ENV_IS_IN_UBI
bool "Environment in a UBI volume"
depends on !CHAIN_OF_TRUST
projects / people / ms / u-boot.git / blobdiff