void get_sys_info (sys_info_t * sysInfo)
{
- volatile ccsr_gur_t *gur = (void *)(CFG_MPC85xx_GUTS_ADDR);
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
uint plat_ratio,e500_ratio,half_freqSystemBus;
plat_ratio = (gur->porpllsr) & 0x0000003e;
* overflow for processor speeds above 2GHz */
half_freqSystemBus = sysInfo->freqSystemBus/2;
sysInfo->freqProcessor = e500_ratio*half_freqSystemBus;
+
+ /* Note: freqDDRBus is the MCLK frequency, not the data rate. */
sysInfo->freqDDRBus = sysInfo->freqSystemBus;
#ifdef CONFIG_DDR_CLK_FREQ
{
- u32 ddr_ratio = ((gur->porpllsr) & 0x00003e00) >> 9;
+ u32 ddr_ratio = ((gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO)
+ >> MPC85xx_PORPLLSR_DDR_RATIO_SHIFT;
if (ddr_ratio != 0x7)
sysInfo->freqDDRBus = ddr_ratio * CONFIG_DDR_CLK_FREQ;
}
int get_clocks (void)
{
sys_info_t sys_info;
+#ifdef CONFIG_MPC8544
+ volatile ccsr_gur_t *gur = (void *) CONFIG_SYS_MPC85xx_GUTS_ADDR;
+#endif
#if defined(CONFIG_CPM2)
- volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CFG_MPC85xx_CPM_ADDR;
+ volatile ccsr_cpm_t *cpm = (ccsr_cpm_t *)CONFIG_SYS_MPC85xx_CPM_ADDR;
uint sccr, dfbrg;
/* set VCO = 4 * BRG */
get_sys_info (&sys_info);
gd->cpu_clk = sys_info.freqProcessor;
gd->bus_clk = sys_info.freqSystemBus;
+ gd->mem_clk = sys_info.freqDDRBus;
+
+ /*
+ * The base clock for I2C depends on the actual SOC. Unfortunately,
+ * there is no pattern that can be used to determine the frequency, so
+ * the only choice is to look up the actual SOC number and use the value
+ * for that SOC. This information is taken from application note
+ * AN2919.
+ */
+#if defined(CONFIG_MPC8540) || defined(CONFIG_MPC8541) || \
+ defined(CONFIG_MPC8560) || defined(CONFIG_MPC8555)
gd->i2c1_clk = sys_info.freqSystemBus;
- gd->i2c2_clk = sys_info.freqSystemBus;
+#elif defined(CONFIG_MPC8544)
+ /*
+ * On the 8544, the I2C clock is the same as the SEC clock. This can be
+ * either CCB/2 or CCB/3, depending on the value of cfg_sec_freq. See
+ * 4.4.3.3 of the 8544 RM. Note that this might actually work for all
+ * 85xx, but only the 8544 has cfg_sec_freq, so it's unknown if the
+ * PORDEVSR2_SEC_CFG bit is 0 on all 85xx boards that are not an 8544.
+ */
+ if (gur->pordevsr2 & MPC85xx_PORDEVSR2_SEC_CFG)
+ gd->i2c1_clk = sys_info.freqSystemBus / 2;
+ else
+ gd->i2c1_clk = sys_info.freqSystemBus / 3;
+#else
+ /* Most 85xx SOCs use CCB/2, so this is the default behavior. */
+ gd->i2c1_clk = sys_info.freqSystemBus / 2;
+#endif
+ gd->i2c2_clk = gd->i2c1_clk;
+
+#if defined(CONFIG_MPC8536)
+ gd->sdhc_clk = gd->bus_clk / 2;
+#endif
#if defined(CONFIG_CPM2)
gd->vco_out = 2*sys_info.freqSystemBus;
*********************************************/
ulong get_bus_freq (ulong dummy)
{
- ulong val;
-
- sys_info_t sys_info;
-
- get_sys_info (&sys_info);
- val = sys_info.freqSystemBus;
-
- return val;
+ return gd->bus_clk;
}
/********************************************
*********************************************/
ulong get_ddr_freq (ulong dummy)
{
- ulong val;
-
- sys_info_t sys_info;
-
- get_sys_info (&sys_info);
- val = sys_info.freqDDRBus;
-
- return val;
+ return gd->mem_clk;
}