#include <common.h>
-#ifdef CONFIG_FSL_I2C
#ifdef CONFIG_HARD_I2C
#include <command.h>
#include <asm/io.h>
#include <asm/fsl_i2c.h> /* HW definitions */
-#define I2C_TIMEOUT (CFG_HZ / 4)
+#define I2C_TIMEOUT (CONFIG_SYS_HZ / 4)
#define I2C_READ_BIT 1
#define I2C_WRITE_BIT 0
+DECLARE_GLOBAL_DATA_PTR;
+
/* Initialize the bus pointer to whatever one the SPD EEPROM is on.
* Default is bus 0. This is necessary because the DDR initialization
* runs from ROM, and we can't switch buses because we can't modify
* the global variables.
*/
-#ifdef CFG_SPD_BUS_NUM
-static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = CFG_SPD_BUS_NUM;
+#ifdef CONFIG_SYS_SPD_BUS_NUM
+static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = CONFIG_SYS_SPD_BUS_NUM;
#else
static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = 0;
#endif
-static volatile struct fsl_i2c *i2c_dev[2] = {
- (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET),
-#ifdef CFG_I2C2_OFFSET
- (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET)
+static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED};
+
+static const struct fsl_i2c *i2c_dev[2] = {
+ (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET),
+#ifdef CONFIG_SYS_I2C2_OFFSET
+ (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET)
#endif
};
+/* I2C speed map for a DFSR value of 1 */
+
+/*
+ * Map I2C frequency dividers to FDR and DFSR values
+ *
+ * This structure is used to define the elements of a table that maps I2C
+ * frequency divider (I2C clock rate divided by I2C bus speed) to a value to be
+ * programmed into the Frequency Divider Ratio (FDR) and Digital Filter
+ * Sampling Rate (DFSR) registers.
+ *
+ * The actual table should be defined in the board file, and it must be called
+ * fsl_i2c_speed_map[].
+ *
+ * The last entry of the table must have a value of {-1, X}, where X is same
+ * FDR/DFSR values as the second-to-last entry. This guarantees that any
+ * search through the array will always find a match.
+ *
+ * The values of the divider must be in increasing numerical order, i.e.
+ * fsl_i2c_speed_map[x+1].divider > fsl_i2c_speed_map[x].divider.
+ *
+ * For this table, the values are based on a value of 1 for the DFSR
+ * register. See the application note AN2919 "Determining the I2C Frequency
+ * Divider Ratio for SCL"
+ *
+ * ColdFire I2C frequency dividers for FDR values are different from
+ * PowerPC. The protocol to use the I2C module is still the same.
+ * A different table is defined and are based on MCF5xxx user manual.
+ *
+ */
+static const struct {
+ unsigned short divider;
+#ifdef __PPC__
+ u8 dfsr;
+#endif
+ u8 fdr;
+} fsl_i2c_speed_map[] = {
+#ifdef __PPC__
+ {160, 1, 32}, {192, 1, 33}, {224, 1, 34}, {256, 1, 35},
+ {288, 1, 0}, {320, 1, 1}, {352, 6, 1}, {384, 1, 2}, {416, 6, 2},
+ {448, 1, 38}, {480, 1, 3}, {512, 1, 39}, {544, 11, 3}, {576, 1, 4},
+ {608, 22, 3}, {640, 1, 5}, {672, 32, 3}, {704, 11, 5}, {736, 43, 3},
+ {768, 1, 6}, {800, 54, 3}, {832, 11, 6}, {896, 1, 42}, {960, 1, 7},
+ {1024, 1, 43}, {1088, 22, 7}, {1152, 1, 8}, {1216, 43, 7}, {1280, 1, 9},
+ {1408, 22, 9}, {1536, 1, 10}, {1664, 22, 10}, {1792, 1, 46},
+ {1920, 1, 11}, {2048, 1, 47}, {2176, 43, 11}, {2304, 1, 12},
+ {2560, 1, 13}, {2816, 43, 13}, {3072, 1, 14}, {3328, 43, 14},
+ {3584, 1, 50}, {3840, 1, 15}, {4096, 1, 51}, {4608, 1, 16},
+ {5120, 1, 17}, {6144, 1, 18}, {7168, 1, 54}, {7680, 1, 19},
+ {8192, 1, 55}, {9216, 1, 20}, {10240, 1, 21}, {12288, 1, 22},
+ {14336, 1, 58}, {15360, 1, 23}, {16384, 1, 59}, {18432, 1, 24},
+ {20480, 1, 25}, {24576, 1, 26}, {28672, 1, 62}, {30720, 1, 27},
+ {32768, 1, 63}, {36864, 1, 28}, {40960, 1, 29}, {49152, 1, 30},
+ {61440, 1, 31}, {-1, 1, 31}
+#elif defined(__M68K__)
+ {20, 32}, {22, 33}, {24, 34}, {26, 35},
+ {28, 0}, {28, 36}, {30, 1}, {32, 37},
+ {34, 2}, {36, 38}, {40, 3}, {40, 39},
+ {44, 4}, {48, 5}, {48, 40}, {56, 6},
+ {56, 41}, {64, 42}, {68, 7}, {72, 43},
+ {80, 8}, {80, 44}, {88, 9}, {96, 41},
+ {104, 10}, {112, 42}, {128, 11}, {128, 43},
+ {144, 12}, {160, 13}, {160, 48}, {192, 14},
+ {192, 49}, {224, 50}, {240, 15}, {256, 51},
+ {288, 16}, {320, 17}, {320, 52}, {384, 18},
+ {384, 53}, {448, 54}, {480, 19}, {512, 55},
+ {576, 20}, {640, 21}, {640, 56}, {768, 22},
+ {768, 57}, {960, 23}, {896, 58}, {1024, 59},
+ {1152, 24}, {1280, 25}, {1280, 60}, {1536, 26},
+ {1536, 61}, {1792, 62}, {1920, 27}, {2048, 63},
+ {2304, 28}, {2560, 29}, {3072, 30}, {3840, 31},
+ {-1, 31}
+#endif
+};
+
+/**
+ * Set the I2C bus speed for a given I2C device
+ *
+ * @param dev: the I2C device
+ * @i2c_clk: I2C bus clock frequency
+ * @speed: the desired speed of the bus
+ *
+ * The I2C device must be stopped before calling this function.
+ *
+ * The return value is the actual bus speed that is set.
+ */
+static unsigned int set_i2c_bus_speed(const struct fsl_i2c *dev,
+ unsigned int i2c_clk, unsigned int speed)
+{
+ unsigned short divider = min(i2c_clk / speed, (unsigned short) -1);
+ unsigned int i;
+
+ /*
+ * We want to choose an FDR/DFSR that generates an I2C bus speed that
+ * is equal to or lower than the requested speed. That means that we
+ * want the first divider that is equal to or greater than the
+ * calculated divider.
+ */
+
+ for (i = 0; i < ARRAY_SIZE(fsl_i2c_speed_map); i++)
+ if (fsl_i2c_speed_map[i].divider >= divider) {
+ u8 fdr;
+#ifdef __PPC__
+ u8 dfsr;
+ dfsr = fsl_i2c_speed_map[i].dfsr;
+#endif
+ fdr = fsl_i2c_speed_map[i].fdr;
+ speed = i2c_clk / fsl_i2c_speed_map[i].divider;
+ writeb(fdr, &dev->fdr); /* set bus speed */
+#ifdef __PPC__
+ writeb(dfsr, &dev->dfsrr); /* set default filter */
+#endif
+ break;
+ }
+
+ return speed;
+}
+
void
i2c_init(int speed, int slaveadd)
{
- volatile struct fsl_i2c *dev;
+ struct fsl_i2c *dev;
+ unsigned int temp;
- dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET);
+ dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
writeb(0, &dev->cr); /* stop I2C controller */
udelay(5); /* let it shutdown in peace */
- writeb(0x3F, &dev->fdr); /* set bus speed */
- writeb(0x3F, &dev->dfsrr); /* set default filter */
+ temp = set_i2c_bus_speed(dev, gd->i2c1_clk, speed);
+ if (gd->flags & GD_FLG_RELOC)
+ i2c_bus_speed[0] = temp;
writeb(slaveadd << 1, &dev->adr); /* write slave address */
writeb(0x0, &dev->sr); /* clear status register */
writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
-#ifdef CFG_I2C2_OFFSET
- dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET);
+#ifdef CONFIG_SYS_I2C2_OFFSET
+ dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET);
writeb(0, &dev->cr); /* stop I2C controller */
udelay(5); /* let it shutdown in peace */
- writeb(0x3F, &dev->fdr); /* set bus speed */
- writeb(0x3F, &dev->dfsrr); /* set default filter */
+ temp = set_i2c_bus_speed(dev, gd->i2c2_clk, speed);
+ if (gd->flags & GD_FLG_RELOC)
+ i2c_bus_speed[1] = temp;
writeb(slaveadd << 1, &dev->adr); /* write slave address */
writeb(0x0, &dev->sr); /* clear status register */
writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
-#endif /* CFG_I2C2_OFFSET */
+#endif
}
static __inline__ int
i2c_wait4bus(void)
{
- ulong timeval = get_timer(0);
+ unsigned long long timeval = get_ticks();
while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) {
- if (get_timer(timeval) > I2C_TIMEOUT) {
+ if ((get_ticks() - timeval) > usec2ticks(I2C_TIMEOUT))
return -1;
- }
}
return 0;
i2c_wait(int write)
{
u32 csr;
- ulong timeval = get_timer(0);
+ unsigned long long timeval = get_ticks();
do {
csr = readb(&i2c_dev[i2c_bus_num]->sr);
}
return 0;
- } while (get_timer (timeval) < I2C_TIMEOUT);
+ } while ((get_ticks() - timeval) < usec2ticks(I2C_TIMEOUT));
debug("i2c_wait: timed out\n");
return -1;
int i2c_set_bus_num(unsigned int bus)
{
-#ifdef CFG_I2C2_OFFSET
+#ifdef CONFIG_SYS_I2C2_OFFSET
if (bus > 1) {
#else
if (bus > 0) {
int i2c_set_bus_speed(unsigned int speed)
{
- return -1;
+ unsigned int i2c_clk = (i2c_bus_num == 1) ? gd->i2c2_clk : gd->i2c1_clk;
+
+ writeb(0, &i2c_dev[i2c_bus_num]->cr); /* stop controller */
+ i2c_bus_speed[i2c_bus_num] =
+ set_i2c_bus_speed(i2c_dev[i2c_bus_num], i2c_clk, speed);
+ writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); /* start controller */
+
+ return 0;
}
unsigned int i2c_get_bus_num(void)
unsigned int i2c_get_bus_speed(void)
{
- return 0;
+ return i2c_bus_speed[i2c_bus_num];
}
+
#endif /* CONFIG_HARD_I2C */
-#endif /* CONFIG_FSL_I2C */