Select this to enable a sysid for Altera devices. Please find
details on the "Embedded Peripherals IP User Guide" of Altera.
+config ATSHA204A
+ bool "Support for Atmel ATSHA204A module"
+ depends on MISC
+ help
+ Enable support for I2C connected Atmel's ATSHA204A
+ CryptoAuthentication module found for example on the Turris Omnia
+ board.
+
+config ROCKCHIP_EFUSE
+ bool "Rockchip e-fuse support"
+ depends on MISC
+ help
+ Enable (read-only) access for the e-fuse block found in Rockchip
+ SoCs: accesses can either be made using byte addressing and a length
+ or through child-nodes that are generated based on the e-fuse map
+ retrieved from the DTS.
+
+ This driver currently supports the RK3399 only, but can easily be
+ extended (by porting the read function from the Linux kernel sources)
+ to support other recent Rockchip devices.
+
config CMD_CROS_EC
bool "Enable crosec command"
depends on CROS_EC
provides a faster and more robust interface than I2C but the bugs
are less interesting.
+config DS4510
+ bool "Enable support for DS4510 CPU supervisor"
+ help
+ Enable support for the Maxim DS4510 CPU supervisor. It has an
+ integrated 64-byte EEPROM, four programmable non-volatile I/O pins
+ and a configurable timer for the supervisor function. The device is
+ connected over I2C.
+
config FSL_SEC_MON
bool "Enable FSL SEC_MON Driver"
help
Programmable memory pages that are stored on the some
Freescale i.MX processors.
+config NUVOTON_NCT6102D
+ bool "Enable Nuvoton NCT6102D Super I/O driver"
+ help
+ If you say Y here, you will get support for the Nuvoton
+ NCT6102D Super I/O driver. This can be used to enable or
+ disable the legacy UART, the watchdog or other devices
+ in the Nuvoton Super IO chips on X86 platforms.
+
config PWRSEQ
bool "Enable power-sequencing drivers"
depends on DM
help
The I2C address of the PCA9551 LED controller.
-config SYSRESET
- bool "Enable support for system reset drivers"
- depends on DM
+config STM32_RCC
+ bool "Enable RCC driver for the STM32 SoC's family"
+ depends on STM32 && MISC
+ help
+ Enable the STM32 RCC driver. The RCC block (Reset and Clock Control
+ block) is responsible of the management of the clock and reset
+ generation.
+ This driver is similar to an MFD driver in the Linux kernel.
+
+config TEGRA_CAR
+ bool "Enable support for the Tegra CAR driver"
+ depends on TEGRA_NO_BPMP
help
- Enable system reset drivers which can be used to reset the CPU or
- board. Each driver can provide a reset method which will be called
- to effect a reset. The uclass will try all available drivers when
- reset_walk() is called.
+ The Tegra CAR (Clock and Reset Controller) is a HW module that
+ controls almost all clocks and resets in a Tegra SoC.
+
+config TEGRA186_BPMP
+ bool "Enable support for the Tegra186 BPMP driver"
+ depends on TEGRA186
+ help
+ The Tegra BPMP (Boot and Power Management Processor) is a separate
+ auxiliary CPU embedded into Tegra to perform power management work,
+ and controls related features such as clocks, resets, power domains,
+ PMIC I2C bus, etc. This driver provides the core low-level
+ communication path by which feature-specific drivers (such as clock)
+ can make requests to the BPMP. This driver is similar to an MFD
+ driver in the Linux kernel.
config WINBOND_W83627
bool "Enable Winbond Super I/O driver"
Hidden option to enable QEMU fw_cfg interface. This will be selected by
either CONFIG_CMD_QFW or CONFIG_GENERATE_ACPI_TABLE.
+config I2C_EEPROM
+ bool "Enable driver for generic I2C-attached EEPROMs"
+ depends on MISC
+ help
+ Enable a generic driver for EEPROMs attached via I2C.
+
+
+config SPL_I2C_EEPROM
+ bool "Enable driver for generic I2C-attached EEPROMs for SPL"
+ depends on MISC && SPL && SPL_DM
+ help
+ This option is an SPL-variant of the I2C_EEPROM option.
+ See the help of I2C_EEPROM for details.
+
+if I2C_EEPROM
+
+config SYS_I2C_EEPROM_ADDR
+ hex "Chip address of the EEPROM device"
+ default 0
+
+config SYS_I2C_EEPROM_BUS
+ int "I2C bus of the EEPROM device."
+ default 0
+
+config SYS_EEPROM_SIZE
+ int "Size in bytes of the EEPROM device"
+ default 256
+
+config SYS_EEPROM_PAGE_WRITE_BITS
+ int "Number of bits used to address bytes in a single page"
+ default 0
+ help
+ The EEPROM page size is 2^SYS_EEPROM_PAGE_WRITE_BITS.
+ A 64 byte page, for example would require six bits.
+
+config SYS_EEPROM_PAGE_WRITE_DELAY_MS
+ int "Number of milliseconds to delay between page writes"
+ default 0
+
+config SYS_I2C_EEPROM_ADDR_LEN
+ int "Length in bytes of the EEPROM memory array address"
+ default 1
+ help
+ Note: This is NOT the chip address length!
+
+config SYS_I2C_EEPROM_ADDR_OVERFLOW
+ hex "EEPROM Address Overflow"
+ default 0
+ help
+ EEPROM chips that implement "address overflow" are ones
+ like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+ address and the extra bits end up in the "chip address" bit
+ slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+ byte chips.
+
+endif
+
+
endmenu
projects / people / ms / u-boot.git / blobdiff