Remove CONFIG_SYS_BOOTCOUNT_SINGLEWORD

[people/ms/u-boot.git] / drivers / misc / Kconfig

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index ecca159d142f69b96aa2dc649e61eaf686050eab..f1c15cb9fa4060eb62a1606930eb5f6794e63509 100644 (file)
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -20,6 +20,27 @@ config ALTERA_SYSID
          Select this to enable a sysid for Altera devices. Please find
          details on the "Embedded Peripherals IP User Guide" of Altera.
 
+config ATSHA204A
+       bool "Support for Atmel ATSHA204A module"
+       depends on MISC
+       help
+          Enable support for I2C connected Atmel's ATSHA204A
+          CryptoAuthentication module found for example on the Turris Omnia
+          board.
+
+config ROCKCHIP_EFUSE
+        bool "Rockchip e-fuse support"
+       depends on MISC
+       help
+         Enable (read-only) access for the e-fuse block found in Rockchip
+         SoCs: accesses can either be made using byte addressing and a length
+         or through child-nodes that are generated based on the e-fuse map
+         retrieved from the DTS.
+
+         This driver currently supports the RK3399 only, but can easily be
+         extended (by porting the read function from the Linux kernel sources)
+         to support other recent Rockchip devices.
+
 config CMD_CROS_EC
        bool "Enable crosec command"
        depends on CROS_EC
@@ -137,6 +158,15 @@ config PCA9551_I2C_ADDR
        help
          The I2C address of the PCA9551 LED controller.
 
+config STM32_RCC
+       bool "Enable RCC driver for the STM32 SoC's family"
+       depends on STM32 && MISC
+       help
+         Enable the STM32 RCC driver. The RCC block (Reset and Clock Control
+         block) is responsible of the management of the clock and reset
+         generation.
+         This driver is similar to an MFD driver in the Linux kernel.
+
 config TEGRA_CAR
        bool "Enable support for the Tegra CAR driver"
        depends on TEGRA_NO_BPMP
@@ -175,4 +205,57 @@ config I2C_EEPROM
        depends on MISC
        help
          Enable a generic driver for EEPROMs attached via I2C.
+
+
+config SPL_I2C_EEPROM
+       bool "Enable driver for generic I2C-attached EEPROMs for SPL"
+       depends on MISC && SPL && SPL_DM
+       help
+         This option is an SPL-variant of the I2C_EEPROM option.
+         See the help of I2C_EEPROM for details.
+
+if I2C_EEPROM
+
+config SYS_I2C_EEPROM_ADDR
+       hex "Chip address of the EEPROM device"
+       default 0
+
+config SYS_I2C_EEPROM_BUS
+       int "I2C bus of the EEPROM device."
+       default 0
+
+config SYS_EEPROM_SIZE
+       int "Size in bytes of the EEPROM device"
+       default 256
+
+config SYS_EEPROM_PAGE_WRITE_BITS
+       int "Number of bits used to address bytes in a single page"
+       default 0
+       help
+         The EEPROM page size is 2^SYS_EEPROM_PAGE_WRITE_BITS.
+         A 64 byte page, for example would require six bits.
+
+config SYS_EEPROM_PAGE_WRITE_DELAY_MS
+       int "Number of milliseconds to delay between page writes"
+       default 0
+
+config SYS_I2C_EEPROM_ADDR_LEN
+       int "Length in bytes of the EEPROM memory array address"
+       default 1
+       help
+         Note: This is NOT the chip address length!
+
+config SYS_I2C_EEPROM_ADDR_OVERFLOW
+       hex "EEPROM Address Overflow"
+       default 0
+       help
+         EEPROM chips that implement "address overflow" are ones
+         like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+         address and the extra bits end up in the "chip address" bit
+         slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+         byte chips.
+
+endif
+
+
 endmenu