* Basic support for AG-AND chips is provided.
*
* Additional technical information is available on
- * http://www.linux-mtd.infradead.org/tech/nand.html
+ * http://www.linux-mtd.infradead.org/doc/nand.html
*
* Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com)
* 2002-2006 Thomas Gleixner (tglx@linutronix.de)
* if we have HW ecc support.
* The AG-AND chips have nice features for speed improvement,
* which are not supported yet. Read / program 4 pages in one go.
+ * BBT table is not serialized, has to be fixed
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
*
*/
-/* XXX U-BOOT XXX */
-#if 0
-#include <linux/module.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/err.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/types.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/nand_ecc.h>
-#include <linux/mtd/compatmac.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <linux/leds.h>
-#include <asm/io.h>
-
-#ifdef CONFIG_MTD_PARTITIONS
-#include <linux/mtd/partitions.h>
-#endif
-
-#endif
-
#include <common.h>
#define ENOTSUPP 524 /* Operation is not supported */
-#if defined(CONFIG_CMD_NAND) && !defined(CFG_NAND_LEGACY)
-
#include <malloc.h>
#include <watchdog.h>
#include <linux/err.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/nand_ecc.h>
+#ifdef CONFIG_MTD_PARTITIONS
+#include <linux/mtd/partitions.h>
+#endif
+
#include <asm/io.h>
#include <asm/errno.h>
-#ifdef CONFIG_JFFS2_NAND
-#include <jffs2/jffs2.h>
+/*
+ * CONFIG_SYS_NAND_RESET_CNT is used as a timeout mechanism when resetting
+ * a flash. NAND flash is initialized prior to interrupts so standard timers
+ * can't be used. CONFIG_SYS_NAND_RESET_CNT should be set to a value
+ * which is greater than (max NAND reset time / NAND status read time).
+ * A conservative default of 200000 (500 us / 25 ns) is used as a default.
+ */
+#ifndef CONFIG_SYS_NAND_RESET_CNT
+#define CONFIG_SYS_NAND_RESET_CNT 200000
#endif
/* Define default oob placement schemes for large and small page devices */
static struct nand_ecclayout nand_oob_128 = {
.eccbytes = 48,
.eccpos = {
- 80, 81, 82, 83, 84, 85, 86, 87,
- 88, 89, 90, 91, 92, 93, 94, 95,
+ 80, 81, 82, 83, 84, 85, 86, 87,
+ 88, 89, 90, 91, 92, 93, 94, 95,
96, 97, 98, 99, 100, 101, 102, 103,
104, 105, 106, 107, 108, 109, 110, 111,
112, 113, 114, 115, 116, 117, 118, 119,
static int nand_wait(struct mtd_info *mtd, struct nand_chip *this);
-/*
- * For devices which display every fart in the system on a seperate LED. Is
- * compiled away when LED support is disabled.
- */
-/* XXX U-BOOT XXX */
-#if 0
-DEFINE_LED_TRIGGER(nand_led_trigger);
-#endif
-
/**
* nand_release_device - [GENERIC] release chip
* @mtd: MTD device structure
*
* Deselect, release chip lock and wake up anyone waiting on the device
*/
-/* XXX U-BOOT XXX */
-#if 0
-static void nand_release_device(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd->priv;
-
- /* De-select the NAND device */
- chip->select_chip(mtd, -1);
-
- /* Release the controller and the chip */
- spin_lock(&chip->controller->lock);
- chip->controller->active = NULL;
- chip->state = FL_READY;
- wake_up(&chip->controller->wq);
- spin_unlock(&chip->controller->lock);
-}
-#else
static void nand_release_device (struct mtd_info *mtd)
{
struct nand_chip *this = mtd->priv;
this->select_chip(mtd, -1); /* De-select the NAND device */
}
-#endif
/**
* nand_read_byte - [DEFAULT] read one byte from the chip
/* We write two bytes, so we dont have to mess with 16 bit
* access
*/
+ nand_get_device(chip, mtd, FL_WRITING);
ofs += mtd->oobsize;
chip->ops.len = chip->ops.ooblen = 2;
chip->ops.datbuf = NULL;
chip->ops.ooboffs = chip->badblockpos & ~0x01;
ret = nand_do_write_oob(mtd, ofs, &chip->ops);
+ nand_release_device(mtd);
}
if (!ret)
mtd->ecc_stats.badblocks++;
+
return ret;
}
struct nand_chip *chip = mtd->priv;
if (!(chip->options & NAND_BBT_SCANNED)) {
- chip->scan_bbt(mtd);
chip->options |= NAND_BBT_SCANNED;
+ chip->scan_bbt(mtd);
}
if (!chip->bbt)
* Wait for the ready pin, after a command
* The timeout is catched later.
*/
-/* XXX U-BOOT XXX */
-#if 0
void nand_wait_ready(struct mtd_info *mtd)
{
struct nand_chip *chip = mtd->priv;
- unsigned long timeo = jiffies + 2;
+ u32 timeo = (CONFIG_SYS_HZ * 20) / 1000;
+ u32 time_start;
- led_trigger_event(nand_led_trigger, LED_FULL);
- /* wait until command is processed or timeout occures */
- do {
- if (chip->dev_ready(mtd))
- break;
- touch_softlockup_watchdog();
- } while (time_before(jiffies, timeo));
- led_trigger_event(nand_led_trigger, LED_OFF);
-}
-EXPORT_SYMBOL_GPL(nand_wait_ready);
-#else
-void nand_wait_ready(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd->priv;
- u32 timeo = (CFG_HZ * 20) / 1000;
-
- reset_timer();
+ time_start = get_timer(0);
/* wait until command is processed or timeout occures */
- while (get_timer(0) < timeo) {
+ while (get_timer(time_start) < timeo) {
if (chip->dev_ready)
if (chip->dev_ready(mtd))
break;
}
}
-#endif
/**
* nand_command - [DEFAULT] Send command to NAND device
{
register struct nand_chip *chip = mtd->priv;
int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE;
+ uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT;
/*
* Write out the command to the device.
NAND_CTRL_CLE | NAND_CTRL_CHANGE);
chip->cmd_ctrl(mtd,
NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE);
- while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ;
+ while (!(chip->read_byte(mtd) & NAND_STATUS_READY) &&
+ (rst_sts_cnt--));
return;
/* This applies to read commands */
int column, int page_addr)
{
register struct nand_chip *chip = mtd->priv;
+ uint32_t rst_sts_cnt = CONFIG_SYS_NAND_RESET_CNT;
/* Emulate NAND_CMD_READOOB */
if (command == NAND_CMD_READOOB) {
NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE);
chip->cmd_ctrl(mtd, NAND_CMD_NONE,
NAND_NCE | NAND_CTRL_CHANGE);
- while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ;
+ while (!(chip->read_byte(mtd) & NAND_STATUS_READY) &&
+ (rst_sts_cnt--));
return;
case NAND_CMD_RNDOUT:
*
* Get the device and lock it for exclusive access
*/
-/* XXX U-BOOT XXX */
-#if 0
-static int
-nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state)
-{
- spinlock_t *lock = &chip->controller->lock;
- wait_queue_head_t *wq = &chip->controller->wq;
- DECLARE_WAITQUEUE(wait, current);
- retry:
- spin_lock(lock);
-
- /* Hardware controller shared among independend devices */
- /* Hardware controller shared among independend devices */
- if (!chip->controller->active)
- chip->controller->active = chip;
-
- if (chip->controller->active == chip && chip->state == FL_READY) {
- chip->state = new_state;
- spin_unlock(lock);
- return 0;
- }
- if (new_state == FL_PM_SUSPENDED) {
- spin_unlock(lock);
- return (chip->state == FL_PM_SUSPENDED) ? 0 : -EAGAIN;
- }
- set_current_state(TASK_UNINTERRUPTIBLE);
- add_wait_queue(wq, &wait);
- spin_unlock(lock);
- schedule();
- remove_wait_queue(wq, &wait);
- goto retry;
-}
-#else
static int nand_get_device (struct nand_chip *this, struct mtd_info *mtd, int new_state)
{
this->state = new_state;
return 0;
}
-#endif
/**
* nand_wait - [DEFAULT] wait until the command is done
* Erase can take up to 400ms and program up to 20ms according to
* general NAND and SmartMedia specs
*/
-/* XXX U-BOOT XXX */
-#if 0
-static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip)
-{
-
- unsigned long timeo = jiffies;
- int status, state = chip->state;
-
- if (state == FL_ERASING)
- timeo += (HZ * 400) / 1000;
- else
- timeo += (HZ * 20) / 1000;
-
- led_trigger_event(nand_led_trigger, LED_FULL);
-
- /* Apply this short delay always to ensure that we do wait tWB in
- * any case on any machine. */
- ndelay(100);
-
- if ((state == FL_ERASING) && (chip->options & NAND_IS_AND))
- chip->cmdfunc(mtd, NAND_CMD_STATUS_MULTI, -1, -1);
- else
- chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
-
- while (time_before(jiffies, timeo)) {
- if (chip->dev_ready) {
- if (chip->dev_ready(mtd))
- break;
- } else {
- if (chip->read_byte(mtd) & NAND_STATUS_READY)
- break;
- }
- cond_resched();
- }
- led_trigger_event(nand_led_trigger, LED_OFF);
-
- status = (int)chip->read_byte(mtd);
- return status;
-}
-#else
static int nand_wait(struct mtd_info *mtd, struct nand_chip *this)
{
unsigned long timeo;
int state = this->state;
+ u32 time_start;
if (state == FL_ERASING)
- timeo = (CFG_HZ * 400) / 1000;
+ timeo = (CONFIG_SYS_HZ * 400) / 1000;
else
- timeo = (CFG_HZ * 20) / 1000;
+ timeo = (CONFIG_SYS_HZ * 20) / 1000;
if ((state == FL_ERASING) && (this->options & NAND_IS_AND))
this->cmdfunc(mtd, NAND_CMD_STATUS_MULTI, -1, -1);
else
this->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1);
- reset_timer();
+ time_start = get_timer(0);
while (1) {
- if (get_timer(0) > timeo) {
+ if (get_timer(time_start) > timeo) {
printf("Timeout!");
return 0x01;
}
}
}
#ifdef PPCHAMELON_NAND_TIMER_HACK
- reset_timer();
- while (get_timer(0) < 10);
+ time_start = get_timer(0);
+ while (get_timer(time_start) < 10)
+ ;
#endif /* PPCHAMELON_NAND_TIMER_HACK */
return this->read_byte(mtd);
}
-#endif
/**
* nand_read_page_raw - [Intern] read raw page data without ecc
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
+ * @page: page number to read
+ *
+ * Not for syndrome calculating ecc controllers, which use a special oob layout
*/
static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
+ uint8_t *buf, int page)
{
chip->read_buf(mtd, buf, mtd->writesize);
chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
return 0;
}
+/**
+ * nand_read_page_raw_syndrome - [Intern] read raw page data without ecc
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
+ *
+ * We need a special oob layout and handling even when OOB isn't used.
+ */
+static int nand_read_page_raw_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
+ uint8_t *buf, int page)
+{
+ int eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ uint8_t *oob = chip->oob_poi;
+ int steps, size;
+
+ for (steps = chip->ecc.steps; steps > 0; steps--) {
+ chip->read_buf(mtd, buf, eccsize);
+ buf += eccsize;
+
+ if (chip->ecc.prepad) {
+ chip->read_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
+
+ chip->read_buf(mtd, oob, eccbytes);
+ oob += eccbytes;
+
+ if (chip->ecc.postpad) {
+ chip->read_buf(mtd, oob, chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
+
+ size = mtd->oobsize - (oob - chip->oob_poi);
+ if (size)
+ chip->read_buf(mtd, oob, size);
+
+ return 0;
+}
+
/**
* nand_read_page_swecc - [REPLACABLE] software ecc based page read function
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
+ * @page: page number to read
*/
static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
+ uint8_t *buf, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
uint8_t *ecc_code = chip->buffers->ecccode;
uint32_t *eccpos = chip->ecc.layout->eccpos;
- chip->ecc.read_page_raw(mtd, chip, buf);
+ chip->ecc.read_page_raw(mtd, chip, buf, page);
for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize)
chip->ecc.calculate(mtd, p, &ecc_calc[i]);
int stat;
stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
+ if (stat < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+ }
+ return 0;
+}
+
+/**
+ * nand_read_subpage - [REPLACABLE] software ecc based sub-page read function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @data_offs: offset of requested data within the page
+ * @readlen: data length
+ * @bufpoi: buffer to store read data
+ */
+static int nand_read_subpage(struct mtd_info *mtd, struct nand_chip *chip, uint32_t data_offs, uint32_t readlen, uint8_t *bufpoi)
+{
+ int start_step, end_step, num_steps;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint8_t *p;
+ int data_col_addr, i, gaps = 0;
+ int datafrag_len, eccfrag_len, aligned_len, aligned_pos;
+ int busw = (chip->options & NAND_BUSWIDTH_16) ? 2 : 1;
+
+ /* Column address wihin the page aligned to ECC size (256bytes). */
+ start_step = data_offs / chip->ecc.size;
+ end_step = (data_offs + readlen - 1) / chip->ecc.size;
+ num_steps = end_step - start_step + 1;
+
+ /* Data size aligned to ECC ecc.size*/
+ datafrag_len = num_steps * chip->ecc.size;
+ eccfrag_len = num_steps * chip->ecc.bytes;
+
+ data_col_addr = start_step * chip->ecc.size;
+ /* If we read not a page aligned data */
+ if (data_col_addr != 0)
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, data_col_addr, -1);
+
+ p = bufpoi + data_col_addr;
+ chip->read_buf(mtd, p, datafrag_len);
+
+ /* Calculate ECC */
+ for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size)
+ chip->ecc.calculate(mtd, p, &chip->buffers->ecccalc[i]);
+
+ /* The performance is faster if to position offsets
+ according to ecc.pos. Let make sure here that
+ there are no gaps in ecc positions */
+ for (i = 0; i < eccfrag_len - 1; i++) {
+ if (eccpos[i + start_step * chip->ecc.bytes] + 1 !=
+ eccpos[i + start_step * chip->ecc.bytes + 1]) {
+ gaps = 1;
+ break;
+ }
+ }
+ if (gaps) {
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize, -1);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ } else {
+ /* send the command to read the particular ecc bytes */
+ /* take care about buswidth alignment in read_buf */
+ aligned_pos = eccpos[start_step * chip->ecc.bytes] & ~(busw - 1);
+ aligned_len = eccfrag_len;
+ if (eccpos[start_step * chip->ecc.bytes] & (busw - 1))
+ aligned_len++;
+ if (eccpos[(start_step + num_steps) * chip->ecc.bytes] & (busw - 1))
+ aligned_len++;
+
+ chip->cmdfunc(mtd, NAND_CMD_RNDOUT, mtd->writesize + aligned_pos, -1);
+ chip->read_buf(mtd, &chip->oob_poi[aligned_pos], aligned_len);
+ }
+
+ for (i = 0; i < eccfrag_len; i++)
+ chip->buffers->ecccode[i] = chip->oob_poi[eccpos[i + start_step * chip->ecc.bytes]];
+
+ p = bufpoi + data_col_addr;
+ for (i = 0; i < eccfrag_len ; i += chip->ecc.bytes, p += chip->ecc.size) {
+ int stat;
+
+ stat = chip->ecc.correct(mtd, p, &chip->buffers->ecccode[i], &chip->buffers->ecccalc[i]);
if (stat == -1)
mtd->ecc_stats.failed++;
else
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
+ * @page: page number to read
*
* Not for syndrome calculating ecc controllers which need a special oob layout
*/
static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
+ uint8_t *buf, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
int stat;
stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]);
- if (stat == -1)
+ if (stat < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += stat;
+ }
+ return 0;
+}
+
+/**
+ * nand_read_page_hwecc_oob_first - [REPLACABLE] hw ecc, read oob first
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: buffer to store read data
+ * @page: page number to read
+ *
+ * Hardware ECC for large page chips, require OOB to be read first.
+ * For this ECC mode, the write_page method is re-used from ECC_HW.
+ * These methods read/write ECC from the OOB area, unlike the
+ * ECC_HW_SYNDROME support with multiple ECC steps, follows the
+ * "infix ECC" scheme and reads/writes ECC from the data area, by
+ * overwriting the NAND manufacturer bad block markings.
+ */
+static int nand_read_page_hwecc_oob_first(struct mtd_info *mtd,
+ struct nand_chip *chip, uint8_t *buf, int page)
+{
+ int i, eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ int eccsteps = chip->ecc.steps;
+ uint8_t *p = buf;
+ uint8_t *ecc_code = chip->buffers->ecccode;
+ uint32_t *eccpos = chip->ecc.layout->eccpos;
+ uint8_t *ecc_calc = chip->buffers->ecccalc;
+
+ /* Read the OOB area first */
+ chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page);
+ chip->read_buf(mtd, chip->oob_poi, mtd->oobsize);
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page);
+
+ for (i = 0; i < chip->ecc.total; i++)
+ ecc_code[i] = chip->oob_poi[eccpos[i]];
+
+ for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) {
+ int stat;
+
+ chip->ecc.hwctl(mtd, NAND_ECC_READ);
+ chip->read_buf(mtd, p, eccsize);
+ chip->ecc.calculate(mtd, p, &ecc_calc[i]);
+
+ stat = chip->ecc.correct(mtd, p, &ecc_code[i], NULL);
+ if (stat < 0)
mtd->ecc_stats.failed++;
else
mtd->ecc_stats.corrected += stat;
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
+ * @page: page number to read
*
* The hw generator calculates the error syndrome automatically. Therefor
* we need a special oob layout and handling.
*/
static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
- uint8_t *buf)
+ uint8_t *buf, int page)
{
int i, eccsize = chip->ecc.size;
int eccbytes = chip->ecc.bytes;
chip->read_buf(mtd, oob, eccbytes);
stat = chip->ecc.correct(mtd, p, oob, NULL);
- if (stat == -1)
+ if (stat < 0)
mtd->ecc_stats.failed++;
else
mtd->ecc_stats.corrected += stat;
oob = ops->oobbuf;
while(1) {
+ WATCHDOG_RESET();
+
bytes = min(mtd->writesize - col, readlen);
aligned = (bytes == mtd->writesize);
/* Now read the page into the buffer */
if (unlikely(ops->mode == MTD_OOB_RAW))
- ret = chip->ecc.read_page_raw(mtd, chip, bufpoi);
+ ret = chip->ecc.read_page_raw(mtd, chip,
+ bufpoi, page);
+ else if (!aligned && NAND_SUBPAGE_READ(chip) && !oob)
+ ret = chip->ecc.read_subpage(mtd, chip, col, bytes, bufpoi);
else
- ret = chip->ecc.read_page(mtd, chip, bufpoi);
+ ret = chip->ecc.read_page(mtd, chip, bufpoi,
+ page);
if (ret < 0)
break;
/* Transfer not aligned data */
if (!aligned) {
- chip->pagebuf = realpage;
+ if (!NAND_SUBPAGE_READ(chip) && !oob)
+ chip->pagebuf = realpage;
memcpy(buf, chip->buffers->databuf + col, bytes);
}
if (mtd->ecc_stats.failed - stats.failed)
return -EBADMSG;
- return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0;
+ return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0;
}
/**
uint8_t *buf = ops->oobbuf;
MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_read_oob: from = 0x%08Lx, len = %i\n",
- (unsigned long long)from, readlen);
+ (unsigned long long)from, readlen);
if (ops->mode == MTD_OOB_AUTO)
len = chip->ecc.layout->oobavail;
if (unlikely(ops->ooboffs >= len)) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt to start read outside oob\n");
+ "Attempt to start read outside oob\n");
return -EINVAL;
}
ops->ooboffs + readlen > ((mtd->size >> chip->page_shift) -
(from >> chip->page_shift)) * len)) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt read beyond end of device\n");
+ "Attempt read beyond end of device\n");
return -EINVAL;
}
page = realpage & chip->pagemask;
while(1) {
+ WATCHDOG_RESET();
sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd);
len = min(len, readlen);
/* Do not allow reads past end of device */
if (ops->datbuf && (from + ops->len) > mtd->size) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt read beyond end of device\n");
+ "Attempt read beyond end of device\n");
return -EINVAL;
}
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: data buffer
+ *
+ * Not for syndrome calculating ecc controllers, which use a special oob layout
*/
static void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
const uint8_t *buf)
chip->write_buf(mtd, chip->oob_poi, mtd->oobsize);
}
+/**
+ * nand_write_page_raw_syndrome - [Intern] raw page write function
+ * @mtd: mtd info structure
+ * @chip: nand chip info structure
+ * @buf: data buffer
+ *
+ * We need a special oob layout and handling even when ECC isn't checked.
+ */
+static void nand_write_page_raw_syndrome(struct mtd_info *mtd, struct nand_chip *chip,
+ const uint8_t *buf)
+{
+ int eccsize = chip->ecc.size;
+ int eccbytes = chip->ecc.bytes;
+ uint8_t *oob = chip->oob_poi;
+ int steps, size;
+
+ for (steps = chip->ecc.steps; steps > 0; steps--) {
+ chip->write_buf(mtd, buf, eccsize);
+ buf += eccsize;
+
+ if (chip->ecc.prepad) {
+ chip->write_buf(mtd, oob, chip->ecc.prepad);
+ oob += chip->ecc.prepad;
+ }
+
+ chip->read_buf(mtd, oob, eccbytes);
+ oob += eccbytes;
+
+ if (chip->ecc.postpad) {
+ chip->write_buf(mtd, oob, chip->ecc.postpad);
+ oob += chip->ecc.postpad;
+ }
+ }
+
+ size = mtd->oobsize - (oob - chip->oob_poi);
+ if (size)
+ chip->write_buf(mtd, oob, size);
+}
/**
* nand_write_page_swecc - [REPLACABLE] software ecc based page write function
* @mtd: mtd info structure
if (!writelen)
return 0;
- /* reject writes, which are not page aligned */
- if (NOTALIGNED(to) || NOTALIGNED(ops->len)) {
- printk(KERN_NOTICE "nand_write: "
- "Attempt to write not page aligned data\n");
- return -EINVAL;
- }
-
column = to & (mtd->writesize - 1);
subpage = column || (writelen & (mtd->writesize - 1));
memset(chip->oob_poi, 0xff, mtd->oobsize);
while(1) {
+ WATCHDOG_RESET();
+
int bytes = mtd->writesize;
int cached = writelen > bytes && page != blockmask;
uint8_t *wbuf = buf;
struct nand_chip *chip = mtd->priv;
MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_write_oob: to = 0x%08x, len = %i\n",
- (unsigned int)to, (int)ops->ooblen);
+ (unsigned int)to, (int)ops->ooblen);
if (ops->mode == MTD_OOB_AUTO)
len = chip->ecc.layout->oobavail;
/* Do not allow write past end of page */
if ((ops->ooboffs + ops->ooblen) > len) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_write_oob: "
- "Attempt to write past end of page\n");
+ "Attempt to write past end of page\n");
return -EINVAL;
}
if (unlikely(ops->ooboffs >= len)) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt to start write outside oob\n");
+ "Attempt to start write outside oob\n");
return -EINVAL;
}
((mtd->size >> chip->page_shift) -
(to >> chip->page_shift)) * len)) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt write beyond end of device\n");
+ "Attempt write beyond end of device\n");
return -EINVAL;
}
/* Do not allow writes past end of device */
if (ops->datbuf && (to + ops->len) > mtd->size) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_read_oob: "
- "Attempt read beyond end of device\n");
+ "Attempt read beyond end of device\n");
return -EINVAL;
}
int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr,
int allowbbt)
{
- int page, len, status, pages_per_block, ret, chipnr;
+ int page, status, pages_per_block, ret, chipnr;
struct nand_chip *chip = mtd->priv;
- int rewrite_bbt[NAND_MAX_CHIPS]={0};
+ loff_t rewrite_bbt[CONFIG_SYS_NAND_MAX_CHIPS] = {0};
unsigned int bbt_masked_page = 0xffffffff;
+ loff_t len;
- MTDDEBUG (MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%08x, len = %i\n",
- (unsigned int) instr->addr, (unsigned int) instr->len);
+ MTDDEBUG(MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%012llx, "
+ "len = %llu\n", (unsigned long long) instr->addr,
+ (unsigned long long) instr->len);
/* Start address must align on block boundary */
if (instr->addr & ((1 << chip->phys_erase_shift) - 1)) {
/* Length must align on block boundary */
if (instr->len & ((1 << chip->phys_erase_shift) - 1)) {
MTDDEBUG (MTD_DEBUG_LEVEL0,
- "nand_erase: Length not block aligned\n");
+ "nand_erase: Length not block aligned\n");
return -EINVAL;
}
/* Do not allow erase past end of device */
if ((instr->len + instr->addr) > mtd->size) {
MTDDEBUG (MTD_DEBUG_LEVEL0,
- "nand_erase: Erase past end of device\n");
+ "nand_erase: Erase past end of device\n");
return -EINVAL;
}
/* Check, if it is write protected */
if (nand_check_wp(mtd)) {
MTDDEBUG (MTD_DEBUG_LEVEL0,
- "nand_erase: Device is write protected!!!\n");
+ "nand_erase: Device is write protected!!!\n");
instr->state = MTD_ERASE_FAILED;
goto erase_exit;
}
instr->state = MTD_ERASING;
while (len) {
+ WATCHDOG_RESET();
/*
* heck if we have a bad block, we do not erase bad blocks !
*/
/* See if block erase succeeded */
if (status & NAND_STATUS_FAIL) {
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_erase: "
- "Failed erase, page 0x%08x\n", page);
+ "Failed erase, page 0x%08x\n", page);
instr->state = MTD_ERASE_FAILED;
- instr->fail_addr = (page << chip->page_shift);
+ instr->fail_addr = ((loff_t)page << chip->page_shift);
goto erase_exit;
}
*/
if (bbt_masked_page != 0xffffffff &&
(page & BBT_PAGE_MASK) == bbt_masked_page)
- rewrite_bbt[chipnr] = (page << chip->page_shift);
+ rewrite_bbt[chipnr] =
+ ((loff_t)page << chip->page_shift);
/* Increment page address and decrement length */
len -= (1 << chip->phys_erase_shift);
erase_exit:
ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO;
- /* Do call back function */
- if (!ret)
- mtd_erase_callback(instr);
/* Deselect and wake up anyone waiting on the device */
nand_release_device(mtd);
+ /* Do call back function */
+ if (!ret)
+ mtd_erase_callback(instr);
+
/*
* If BBT requires refresh and erase was successful, rewrite any
* selected bad block tables
continue;
/* update the BBT for chip */
MTDDEBUG (MTD_DEBUG_LEVEL0, "nand_erase_nand: nand_update_bbt "
- "(%d:0x%0x 0x%0x)\n", chipnr, rewrite_bbt[chipnr],
- chip->bbt_td->pages[chipnr]);
+ "(%d:0x%0llx 0x%0x)\n", chipnr, rewrite_bbt[chipnr],
+ chip->bbt_td->pages[chipnr]);
nand_update_bbt(mtd, rewrite_bbt[chipnr]);
}
return chip->block_markbad(mtd, ofs);
}
-/**
- * nand_suspend - [MTD Interface] Suspend the NAND flash
- * @mtd: MTD device structure
- */
-static int nand_suspend(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd->priv;
-
- return nand_get_device(chip, mtd, FL_PM_SUSPENDED);
-}
-
-/**
- * nand_resume - [MTD Interface] Resume the NAND flash
- * @mtd: MTD device structure
- */
-static void nand_resume(struct mtd_info *mtd)
-{
- struct nand_chip *chip = mtd->priv;
-
- if (chip->state == FL_PM_SUSPENDED)
- nand_release_device(mtd);
- else
- printk(KERN_ERR "nand_resume() called for a chip which is not "
- "in suspended state\n");
-}
-
/*
* Set default functions
*/
chip->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf;
if (!chip->scan_bbt)
chip->scan_bbt = nand_default_bbt;
-
- if (!chip->controller) {
+ if (!chip->controller)
chip->controller = &chip->hwcontrol;
+}
- /* XXX U-BOOT XXX */
-#if 0
- spin_lock_init(&chip->controller->lock);
- init_waitqueue_head(&chip->controller->wq);
-#endif
+#ifdef CONFIG_SYS_NAND_ONFI_DETECTION
+static u16 onfi_crc16(u16 crc, u8 const *p, size_t len)
+{
+ int i;
+
+ while (len--) {
+ crc ^= *p++ << 8;
+ for (i = 0; i < 8; i++)
+ crc = (crc << 1) ^ ((crc & 0x8000) ? 0x8005 : 0);
}
+ return crc;
}
/*
- * Get the flash and manufacturer id and lookup if the type is supported
+ * Check if the NAND chip is ONFI compliant, returns 1 if it is, 0 otherwise
*/
-static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
- struct nand_chip *chip,
- int busw, int *maf_id)
+static int nand_flash_detect_onfi(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ int *busw)
{
- struct nand_flash_dev *type = NULL;
- int i, dev_id, maf_idx;
-
- /* Select the device */
- chip->select_chip(mtd, 0);
-
- /* Send the command for reading device ID */
- chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+ struct nand_onfi_params *p = &chip->onfi_params;
+ int i;
+ int val;
- /* Read manufacturer and device IDs */
- *maf_id = chip->read_byte(mtd);
- dev_id = chip->read_byte(mtd);
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x20, -1);
+ if (chip->read_byte(mtd) != 'O' || chip->read_byte(mtd) != 'N' ||
+ chip->read_byte(mtd) != 'F' || chip->read_byte(mtd) != 'I')
+ return 0;
- /* Lookup the flash id */
- for (i = 0; nand_flash_ids[i].name != NULL; i++) {
- if (dev_id == nand_flash_ids[i].id) {
- type = &nand_flash_ids[i];
+ printk(KERN_INFO "ONFI flash detected\n");
+ chip->cmdfunc(mtd, NAND_CMD_PARAM, 0, -1);
+ for (i = 0; i < 3; i++) {
+ chip->read_buf(mtd, (uint8_t *)p, sizeof(*p));
+ if (onfi_crc16(ONFI_CRC_BASE, (uint8_t *)p, 254) ==
+ le16_to_cpu(p->crc)) {
+ printk(KERN_INFO "ONFI param page %d valid\n", i);
break;
}
}
- if (!type)
- return ERR_PTR(-ENODEV);
+ if (i == 3)
+ return 0;
+
+ /* check version */
+ val = le16_to_cpu(p->revision);
+ if (val == 1 || val > (1 << 4)) {
+ printk(KERN_INFO "%s: unsupported ONFI "
+ "version: %d\n", __func__, val);
+ return 0;
+ }
+
+ if (val & (1 << 4))
+ chip->onfi_version = 22;
+ else if (val & (1 << 3))
+ chip->onfi_version = 21;
+ else if (val & (1 << 2))
+ chip->onfi_version = 20;
+ else
+ chip->onfi_version = 10;
if (!mtd->name)
- mtd->name = type->name;
+ mtd->name = p->model;
+
+ mtd->writesize = le32_to_cpu(p->byte_per_page);
+ mtd->erasesize = le32_to_cpu(p->pages_per_block) * mtd->writesize;
+ mtd->oobsize = le16_to_cpu(p->spare_bytes_per_page);
+ chip->chipsize = (uint64_t)le32_to_cpu(p->blocks_per_lun) * mtd->erasesize;
+ *busw = 0;
+ if (le16_to_cpu(p->features) & 1)
+ *busw = NAND_BUSWIDTH_16;
- chip->chipsize = type->chipsize << 20;
+ return 1;
+}
+#else
+static inline int nand_flash_detect_onfi(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ int *busw)
+{
+ return 0;
+}
+#endif
+static void nand_flash_detect_non_onfi(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ const struct nand_flash_dev *type,
+ int *busw)
+{
/* Newer devices have all the information in additional id bytes */
if (!type->pagesize) {
int extid;
mtd->erasesize = (64 * 1024) << (extid & 0x03);
extid >>= 2;
/* Get buswidth information */
- busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0;
+ *busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0;
} else {
/*
mtd->erasesize = type->erasesize;
mtd->writesize = type->pagesize;
mtd->oobsize = mtd->writesize / 32;
- busw = type->options & NAND_BUSWIDTH_16;
+ *busw = type->options & NAND_BUSWIDTH_16;
+ }
+}
+
+/*
+ * Get the flash and manufacturer id and lookup if the type is supported
+ */
+static const struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd,
+ struct nand_chip *chip,
+ int busw,
+ int *maf_id, int *dev_id,
+ const struct nand_flash_dev *type)
+{
+ int ret, maf_idx;
+ int tmp_id, tmp_manf;
+
+ /* Select the device */
+ chip->select_chip(mtd, 0);
+
+ /*
+ * Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx)
+ * after power-up
+ */
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+
+ /* Send the command for reading device ID */
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+
+ /* Read manufacturer and device IDs */
+ *maf_id = chip->read_byte(mtd);
+ *dev_id = chip->read_byte(mtd);
+
+ /* Try again to make sure, as some systems the bus-hold or other
+ * interface concerns can cause random data which looks like a
+ * possibly credible NAND flash to appear. If the two results do
+ * not match, ignore the device completely.
+ */
+
+ chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
+
+ /* Read manufacturer and device IDs */
+
+ tmp_manf = chip->read_byte(mtd);
+ tmp_id = chip->read_byte(mtd);
+
+ if (tmp_manf != *maf_id || tmp_id != *dev_id) {
+ printk(KERN_INFO "%s: second ID read did not match "
+ "%02x,%02x against %02x,%02x\n", __func__,
+ *maf_id, *dev_id, tmp_manf, tmp_id);
+ return ERR_PTR(-ENODEV);
+ }
+
+ if (!type)
+ type = nand_flash_ids;
+
+ for (; type->name != NULL; type++)
+ if (*dev_id == type->id)
+ break;
+
+ if (!type->name) {
+ /* supress warning if there is no nand */
+ if (*maf_id != 0x00 && *maf_id != 0xff &&
+ *dev_id != 0x00 && *dev_id != 0xff)
+ printk(KERN_INFO "%s: unknown NAND device: "
+ "Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
+ __func__, *maf_id, *dev_id);
+ return ERR_PTR(-ENODEV);
}
+ if (!mtd->name)
+ mtd->name = type->name;
+
+ chip->chipsize = (uint64_t)type->chipsize << 20;
+ chip->onfi_version = 0;
+
+ ret = nand_flash_detect_onfi(mtd, chip, &busw);
+ if (!ret)
+ nand_flash_detect_non_onfi(mtd, chip, type, &busw);
+
+ /* Get chip options, preserve non chip based options */
+ chip->options &= ~NAND_CHIPOPTIONS_MSK;
+ chip->options |= type->options & NAND_CHIPOPTIONS_MSK;
+
+ /*
+ * Set chip as a default. Board drivers can override it, if necessary
+ */
+ chip->options |= NAND_NO_AUTOINCR;
+
/* Try to identify manufacturer */
for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) {
if (nand_manuf_ids[maf_idx].id == *maf_id)
if (busw != (chip->options & NAND_BUSWIDTH_16)) {
printk(KERN_INFO "NAND device: Manufacturer ID:"
" 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id,
- dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
+ *dev_id, nand_manuf_ids[maf_idx].name, mtd->name);
printk(KERN_WARNING "NAND bus width %d instead %d bit\n",
(chip->options & NAND_BUSWIDTH_16) ? 16 : 8,
busw ? 16 : 8);
chip->bbt_erase_shift = chip->phys_erase_shift =
ffs(mtd->erasesize) - 1;
- chip->chip_shift = ffs(chip->chipsize) - 1;
+ if (chip->chipsize & 0xffffffff)
+ chip->chip_shift = ffs((unsigned)chip->chipsize) - 1;
+ else
+ chip->chip_shift = ffs((unsigned)(chip->chipsize >> 32)) + 31;
/* Set the bad block position */
chip->badblockpos = mtd->writesize > 512 ?
NAND_LARGE_BADBLOCK_POS : NAND_SMALL_BADBLOCK_POS;
- /* Get chip options, preserve non chip based options */
- chip->options &= ~NAND_CHIPOPTIONS_MSK;
- chip->options |= type->options & NAND_CHIPOPTIONS_MSK;
-
- /*
- * Set chip as a default. Board drivers can override it, if necessary
- */
- chip->options |= NAND_NO_AUTOINCR;
-
/* Check if chip is a not a samsung device. Do not clear the
* options for chips which are not having an extended id.
*/
chip->cmdfunc = nand_command_lp;
MTDDEBUG (MTD_DEBUG_LEVEL0, "NAND device: Manufacturer ID:"
- " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, dev_id,
- nand_manuf_ids[maf_idx].name, type->name);
+ " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, *dev_id,
+ nand_manuf_ids[maf_idx].name, type->name);
return type;
}
* nand_scan_ident - [NAND Interface] Scan for the NAND device
* @mtd: MTD device structure
* @maxchips: Number of chips to scan for
+ * @table: Alternative NAND ID table
*
* This is the first phase of the normal nand_scan() function. It
* reads the flash ID and sets up MTD fields accordingly.
*
* The mtd->owner field must be set to the module of the caller.
*/
-int nand_scan_ident(struct mtd_info *mtd, int maxchips)
+int nand_scan_ident(struct mtd_info *mtd, int maxchips,
+ const struct nand_flash_dev *table)
{
- int i, busw, nand_maf_id;
+ int i, busw, nand_maf_id, nand_dev_id;
struct nand_chip *chip = mtd->priv;
- struct nand_flash_dev *type;
+ const struct nand_flash_dev *type;
/* Get buswidth to select the correct functions */
busw = chip->options & NAND_BUSWIDTH_16;
nand_set_defaults(chip, busw);
/* Read the flash type */
- type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id);
+ type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id, &nand_dev_id, table);
if (IS_ERR(type)) {
+#ifndef CONFIG_SYS_NAND_QUIET_TEST
printk(KERN_WARNING "No NAND device found!!!\n");
+#endif
chip->select_chip(mtd, -1);
return PTR_ERR(type);
}
/* Check for a chip array */
for (i = 1; i < maxchips; i++) {
chip->select_chip(mtd, i);
+ /* See comment in nand_get_flash_type for reset */
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
/* Send the command for reading device ID */
chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
/* Read manufacturer and device IDs */
if (nand_maf_id != chip->read_byte(mtd) ||
- type->id != chip->read_byte(mtd))
+ nand_dev_id != chip->read_byte(mtd))
break;
}
+#ifdef DEBUG
if (i > 1)
printk(KERN_INFO "%d NAND chips detected\n", i);
+#endif
/* Store the number of chips and calc total size for mtd */
chip->numchips = i;
/**
* nand_scan_tail - [NAND Interface] Scan for the NAND device
* @mtd: MTD device structure
- * @maxchips: Number of chips to scan for
*
* This is the second phase of the normal nand_scan() function. It
* fills out all the uninitialized function pointers with the defaults
default:
printk(KERN_WARNING "No oob scheme defined for "
"oobsize %d\n", mtd->oobsize);
-/* BUG(); */
}
}
* check ECC mode, default to software if 3byte/512byte hardware ECC is
* selected and we have 256 byte pagesize fallback to software ECC
*/
- if (!chip->ecc.read_page_raw)
- chip->ecc.read_page_raw = nand_read_page_raw;
- if (!chip->ecc.write_page_raw)
- chip->ecc.write_page_raw = nand_write_page_raw;
switch (chip->ecc.mode) {
+ case NAND_ECC_HW_OOB_FIRST:
+ /* Similar to NAND_ECC_HW, but a separate read_page handle */
+ if (!chip->ecc.calculate || !chip->ecc.correct ||
+ !chip->ecc.hwctl) {
+ printk(KERN_WARNING "No ECC functions supplied, "
+ "Hardware ECC not possible\n");
+ BUG();
+ }
+ if (!chip->ecc.read_page)
+ chip->ecc.read_page = nand_read_page_hwecc_oob_first;
+
case NAND_ECC_HW:
/* Use standard hwecc read page function ? */
if (!chip->ecc.read_page)
chip->ecc.read_page = nand_read_page_hwecc;
if (!chip->ecc.write_page)
chip->ecc.write_page = nand_write_page_hwecc;
+ if (!chip->ecc.read_page_raw)
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ if (!chip->ecc.write_page_raw)
+ chip->ecc.write_page_raw = nand_write_page_raw;
if (!chip->ecc.read_oob)
chip->ecc.read_oob = nand_read_oob_std;
if (!chip->ecc.write_oob)
chip->ecc.read_page = nand_read_page_syndrome;
if (!chip->ecc.write_page)
chip->ecc.write_page = nand_write_page_syndrome;
+ if (!chip->ecc.read_page_raw)
+ chip->ecc.read_page_raw = nand_read_page_raw_syndrome;
+ if (!chip->ecc.write_page_raw)
+ chip->ecc.write_page_raw = nand_write_page_raw_syndrome;
if (!chip->ecc.read_oob)
chip->ecc.read_oob = nand_read_oob_syndrome;
if (!chip->ecc.write_oob)
chip->ecc.calculate = nand_calculate_ecc;
chip->ecc.correct = nand_correct_data;
chip->ecc.read_page = nand_read_page_swecc;
+ chip->ecc.read_subpage = nand_read_subpage;
chip->ecc.write_page = nand_write_page_swecc;
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ chip->ecc.write_page_raw = nand_write_page_raw;
chip->ecc.read_oob = nand_read_oob_std;
chip->ecc.write_oob = nand_write_oob_std;
chip->ecc.size = 256;
chip->ecc.read_page = nand_read_page_raw;
chip->ecc.write_page = nand_write_page_raw;
chip->ecc.read_oob = nand_read_oob_std;
+ chip->ecc.read_page_raw = nand_read_page_raw;
+ chip->ecc.write_page_raw = nand_write_page_raw;
chip->ecc.write_oob = nand_write_oob_std;
chip->ecc.size = mtd->writesize;
chip->ecc.bytes = 0;
* the out of band area
*/
chip->ecc.layout->oobavail = 0;
- for (i = 0; chip->ecc.layout->oobfree[i].length; i++)
+ for (i = 0; chip->ecc.layout->oobfree[i].length
+ && i < ARRAY_SIZE(chip->ecc.layout->oobfree); i++)
chip->ecc.layout->oobavail +=
chip->ecc.layout->oobfree[i].length;
mtd->oobavail = chip->ecc.layout->oobavail;
break;
case 4:
case 8:
+ case 16:
mtd->subpage_sft = 2;
break;
}
mtd->sync = nand_sync;
mtd->lock = NULL;
mtd->unlock = NULL;
- mtd->suspend = nand_suspend;
- mtd->resume = nand_resume;
mtd->block_isbad = nand_block_isbad;
mtd->block_markbad = nand_block_markbad;
return 0;
}
-/* module_text_address() isn't exported, and it's mostly a pointless
- test if this is a module _anyway_ -- they'd have to try _really_ hard
- to call us from in-kernel code if the core NAND support is modular. */
-#ifdef MODULE
-#define caller_is_module() (1)
-#else
-#define caller_is_module() \
- module_text_address((unsigned long)__builtin_return_address(0))
-#endif
-
/**
* nand_scan - [NAND Interface] Scan for the NAND device
* @mtd: MTD device structure
{
int ret;
- /* Many callers got this wrong, so check for it for a while... */
- /* XXX U-BOOT XXX */
-#if 0
- if (!mtd->owner && caller_is_module()) {
- printk(KERN_CRIT "nand_scan() called with NULL mtd->owner!\n");
- BUG();
- }
-#endif
-
- ret = nand_scan_ident(mtd, maxchips);
+ ret = nand_scan_ident(mtd, maxchips, NULL);
if (!ret)
ret = nand_scan_tail(mtd);
return ret;
/* Deregister partitions */
del_mtd_partitions(mtd);
#endif
- /* Deregister the device */
- /* XXX U-BOOT XXX */
-#if 0
- del_mtd_device(mtd);
-#endif
/* Free bad block table memory */
kfree(chip->bbt);
if (!(chip->options & NAND_OWN_BUFFERS))
kfree(chip->buffers);
}
-
-/* XXX U-BOOT XXX */
-#if 0
-EXPORT_SYMBOL_GPL(nand_scan);
-EXPORT_SYMBOL_GPL(nand_scan_ident);
-EXPORT_SYMBOL_GPL(nand_scan_tail);
-EXPORT_SYMBOL_GPL(nand_release);
-
-static int __init nand_base_init(void)
-{
- led_trigger_register_simple("nand-disk", &nand_led_trigger);
- return 0;
-}
-
-static void __exit nand_base_exit(void)
-{
- led_trigger_unregister_simple(nand_led_trigger);
-}
-
-module_init(nand_base_init);
-module_exit(nand_base_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Steven J. Hill <sjhill@realitydiluted.com>, Thomas Gleixner <tglx@linutronix.de>");
-MODULE_DESCRIPTION("Generic NAND flash driver code");
-#endif
-
-#endif
-