# management frames); ath0 for madwifi
interface=wlan0
-# In case of madwifi and nl80211 driver interfaces, an additional configuration
-# parameter, bridge, must be used to notify hostapd if the interface is
-# included in a bridge. This parameter is not used with Host AP driver.
+# In case of madwifi, atheros, and nl80211 driver interfaces, an additional
+# configuration parameter, bridge, may be used to notify hostapd if the
+# interface is included in a bridge. This parameter is not used with Host AP
+# driver. If the bridge parameter is not set, the drivers will automatically
+# figure out the bridge interface (assuming sysfs is enabled and mounted to
+# /sys) and this parameter may not be needed.
+#
+# For nl80211, this parameter can be used to request the AP interface to be
+# added to the bridge automatically (brctl may refuse to do this before hostapd
+# has been started to change the interface mode). If needed, the bridge
+# interface is also created.
#bridge=br0
-# Driver interface type (hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
+# Driver interface type (hostap/wired/madwifi/test/none/nl80211/bsd);
# default: hostap). nl80211 is used with all Linux mac80211 drivers.
# Use driver=none if building hostapd as a standalone RADIUS server that does
# not control any wireless/wired driver.
# SSID to be used in IEEE 802.11 management frames
ssid=test
+# Alternative formats for configuring SSID
+# (double quoted string, hexdump, printf-escaped string)
+#ssid2="test"
+#ssid2=74657374
+#ssid2=P"hello\nthere"
+
+# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding
+#utf8_ssid=1
# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
# Set as needed to indicate country in which device is operating.
#ieee80211d=1
# Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g,
+# ad = IEEE 802.11ad (60 GHz); a/g options are used with IEEE 802.11n, too, to
+# specify band)
# Default: IEEE 802.11b
-hw_mode=a
+hw_mode=g
# Channel number (IEEE 802.11)
# (default: 0, i.e., not set)
-# Please note that some drivers (e.g., madwifi) do not use this value from
-# hostapd and the channel will need to be configuration separately with
-# iwconfig.
-channel=60
+# Please note that some drivers do not use this value from hostapd and the
+# channel will need to be configured separately with iwconfig.
+channel=1
# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535)
beacon_int=100
-# DTIM (delivery trafic information message) period (range 1..255):
+# DTIM (delivery traffic information message) period (range 1..255):
# number of beacons between DTIMs (1 = every beacon includes DTIM element)
# (default: 2)
dtim_period=2
# requests for broadcast SSID
ignore_broadcast_ssid=0
+# Additional vendor specfic elements for Beacon and Probe Response frames
+# This parameter can be used to add additional vendor specific element(s) into
+# the end of the Beacon and Probe Response frames. The format for these
+# element(s) is a hexdump of the raw information elements (id+len+payload for
+# one or more elements)
+#vendor_elements=dd0411223301
+
# TX queue parameters (EDCF / bursting)
-# default for all these fields: not set, use hardware defaults
# tx_queue_<queue name>_<param>
# queues: data0, data1, data2, data3, after_beacon, beacon
# (data0 is the highest priority queue)
#tx_queue_data0_cwmax=7
#tx_queue_data0_burst=1.5
# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3
-#
-# Special queues; normally not user configurable
-#
-#tx_queue_after_beacon_aifs=2
-#tx_queue_after_beacon_cwmin=15
-#tx_queue_after_beacon_cwmax=1023
-#tx_queue_after_beacon_burst=0
-#
-#tx_queue_beacon_aifs=2
-#tx_queue_beacon_cwmin=3
-#tx_queue_beacon_cwmax=7
-#tx_queue_beacon_burst=1.5
# 802.1D Tag (= UP) to AC mappings
# WMM specifies following mapping of data frames to different ACs. This mapping
#
wmm_enabled=1
#
+# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD]
+# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver)
+#uapsd_advertisement_enabled=1
+#
# Low priority / AC_BK = background
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
# the STA with a data frame.
# default: 300 (i.e., 5 minutes)
#ap_max_inactivity=300
-
-# Enable/disable internal bridge for packets between associated stations.
-#
-# When IEEE 802.11 is used in managed mode, packets are usually send through
-# the AP even if they are from a wireless station to another wireless station.
-# This functionality requires that the AP has a bridge functionality that sends
-# frames back to the same interface if their destination is another associated
-# station. In addition, broadcast/multicast frames from wireless stations will
-# be sent both to the host system net stack (e.g., to eventually wired network)
-# and back to the wireless interface.
-#
-# The internal bridge is implemented within the wireless kernel module and it
-# bypasses kernel filtering (netfilter/iptables/ebtables). If direct
-# communication between the stations needs to be prevented, the internal
-# bridge can be disabled by setting bridge_packets=0.
#
-# Note: If this variable is not included in hostapd.conf, hostapd does not
-# change the configuration and iwpriv can be used to set the value with
-# 'iwpriv wlan# param 10 0' command. If the variable is in hostapd.conf,
-# hostapd will override possible iwpriv configuration whenever configuration
-# file is reloaded.
-#
-# default: do not control from hostapd (80211.o defaults to 1=enabled)
-#bridge_packets=1
+# The inactivity polling can be disabled to disconnect stations based on
+# inactivity timeout so that idle stations are more likely to be disconnected
+# even if they are still in range of the AP. This can be done by setting
+# skip_inactivity_poll to 1 (default 0).
+#skip_inactivity_poll=0
+
+# Disassociate stations based on excessive transmission failures or other
+# indications of connection loss. This depends on the driver capabilities and
+# may not be available with all drivers.
+#disassoc_low_ack=1
# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to
# remain asleep). Default: 65535 (no limit apart from field size)
#max_listen_interval=100
+# WDS (4-address frame) mode with per-station virtual interfaces
+# (only supported with driver=nl80211)
+# This mode allows associated stations to use 4-address frames to allow layer 2
+# bridging to be used.
+#wds_sta=1
+
+# If bridge parameter is set, the WDS STA interface will be added to the same
+# bridge by default. This can be overridden with the wds_bridge parameter to
+# use a separate bridge.
+#wds_bridge=wds-br0
+
+# Client isolation can be used to prevent low-level bridging of frames between
+# associated stations in the BSS. By default, this bridging is allowed.
+#ap_isolate=1
+
##### IEEE 802.11n related configuration ######################################
# ieee80211n: Whether IEEE 802.11n (HT) is enabled
# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set)
#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]
+# Require stations to support HT PHY (reject association if they do not)
+#require_ht=1
+
+##### IEEE 802.11ac related configuration #####################################
+
+# ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled
+# 0 = disabled (default)
+# 1 = enabled
+# Note: You will also need to enable WMM for full VHT functionality.
+#ieee80211ac=1
+
+# vht_capab: VHT capabilities (list of flags)
+#
+# vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454]
+# Indicates maximum MPDU length
+# 0 = 3895 octets (default)
+# 1 = 7991 octets
+# 2 = 11454 octets
+# 3 = reserved
+#
+# supported_chan_width: [VHT160] [VHT160-80PLUS80]
+# Indicates supported Channel widths
+# 0 = 160 MHz & 80+80 channel widths are not supported (default)
+# 1 = 160 MHz channel width is supported
+# 2 = 160 MHz & 80+80 channel widths are supported
+# 3 = reserved
+#
+# Rx LDPC coding capability: [RXLDPC]
+# Indicates support for receiving LDPC coded pkts
+# 0 = Not supported (default)
+# 1 = Supported
+#
+# Short GI for 80 MHz: [SHORT-GI-80]
+# Indicates short GI support for reception of packets transmitted with TXVECTOR
+# params format equal to VHT and CBW = 80Mhz
+# 0 = Not supported (default)
+# 1 = Supported
+#
+# Short GI for 160 MHz: [SHORT-GI-160]
+# Indicates short GI support for reception of packets transmitted with TXVECTOR
+# params format equal to VHT and CBW = 160Mhz
+# 0 = Not supported (default)
+# 1 = Supported
+#
+# Tx STBC: [TX-STBC-2BY1]
+# Indicates support for the transmission of at least 2x1 STBC
+# 0 = Not supported (default)
+# 1 = Supported
+#
+# Rx STBC: [RX-STBC-1] [RX-STBC-12] [RX-STBC-123] [RX-STBC-1234]
+# Indicates support for the reception of PPDUs using STBC
+# 0 = Not supported (default)
+# 1 = support of one spatial stream
+# 2 = support of one and two spatial streams
+# 3 = support of one, two and three spatial streams
+# 4 = support of one, two, three and four spatial streams
+# 5,6,7 = reserved
+#
+# SU Beamformer Capable: [SU-BEAMFORMER]
+# Indicates support for operation as a single user beamformer
+# 0 = Not supported (default)
+# 1 = Supported
+#
+# SU Beamformee Capable: [SU-BEAMFORMEE]
+# Indicates support for operation as a single user beamformee
+# 0 = Not supported (default)
+# 1 = Supported
+#
+# Compressed Steering Number of Beamformer Antennas Supported: [BF-ANTENNA-2]
+# Beamformee's capability indicating the maximum number of beamformer
+# antennas the beamformee can support when sending compressed beamforming
+# feedback
+# If SU beamformer capable, set to maximum value minus 1
+# else reserved (default)
+#
+# Number of Sounding Dimensions: [SOUNDING-DIMENSION-2]
+# Beamformer's capability indicating the maximum value of the NUM_STS parameter
+# in the TXVECTOR of a VHT NDP
+# If SU beamformer capable, set to maximum value minus 1
+# else reserved (default)
+#
+# MU Beamformer Capable: [MU-BEAMFORMER]
+# Indicates support for operation as an MU beamformer
+# 0 = Not supported or sent by Non-AP STA (default)
+# 1 = Supported
+#
+# MU Beamformee Capable: [MU-BEAMFORMEE]
+# Indicates support for operation as an MU beamformee
+# 0 = Not supported or sent by AP (default)
+# 1 = Supported
+#
+# VHT TXOP PS: [VHT-TXOP-PS]
+# Indicates whether or not the AP supports VHT TXOP Power Save Mode
+# or whether or not the STA is in VHT TXOP Power Save mode
+# 0 = VHT AP doesnt support VHT TXOP PS mode (OR) VHT Sta not in VHT TXOP PS
+# mode
+# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT Sta is in VHT TXOP power save
+# mode
+#
+# +HTC-VHT Capable: [HTC-VHT]
+# Indicates whether or not the STA supports receiving a VHT variant HT Control
+# field.
+# 0 = Not supported (default)
+# 1 = supported
+#
+# Maximum A-MPDU Length Exponent: [MAX-A-MPDU-LEN-EXP0]..[MAX-A-MPDU-LEN-EXP7]
+# Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv
+# This field is an integer in the range of 0 to 7.
+# The length defined by this field is equal to
+# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets
+#
+# VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3]
+# Indicates whether or not the STA supports link adaptation using VHT variant
+# HT Control field
+# If +HTC-VHTcapable is 1
+# 0 = (no feedback) if the STA does not provide VHT MFB (default)
+# 1 = reserved
+# 2 = (Unsolicited) if the STA provides only unsolicited VHT MFB
+# 3 = (Both) if the STA can provide VHT MFB in response to VHT MRQ and if the
+# STA provides unsolicited VHT MFB
+# Reserved if +HTC-VHTcapable is 0
+#
+# Rx Antenna Pattern Consistency: [RX-ANTENNA-PATTERN]
+# Indicates the possibility of Rx antenna pattern change
+# 0 = Rx antenna pattern might change during the lifetime of an association
+# 1 = Rx antenna pattern does not change during the lifetime of an association
+#
+# Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN]
+# Indicates the possibility of Tx antenna pattern change
+# 0 = Tx antenna pattern might change during the lifetime of an association
+# 1 = Tx antenna pattern does not change during the lifetime of an association
+#vht_capab=[SHORT-GI-80][HTC-VHT]
+#
+# Require stations to support VHT PHY (reject association if they do not)
+#require_vht=1
+
+# 0 = 20 or 40 MHz operating Channel width
+# 1 = 80 MHz channel width
+# 2 = 160 MHz channel width
+# 3 = 80+80 MHz channel width
+#vht_oper_chwidth=1
+#
+# center freq = 5 GHz + (5 * index)
+# So index 42 gives center freq 5.210 GHz
+# which is channel 42 in 5G band
+#
+#vht_oper_centr_freq_seg0_idx=42
+#
+# center freq = 5 GHz + (5 * index)
+# So index 159 gives center freq 5.795 GHz
+# which is channel 159 in 5G band
+#
+#vht_oper_centr_freq_seg1_idx=159
+
##### IEEE 802.1X-2004 related configuration ##################################
# Require IEEE 802.1X authorization
eap_server=0
# Path for EAP server user database
+# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db"
+# to use SQLite database instead of a text file.
#eap_user_file=/etc/hostapd.eap_user
# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
# "openssl dhparam -out /etc/hostapd.dh.pem 1024"
#dh_file=/etc/hostapd.dh.pem
+# Fragment size for EAP methods
+#fragment_size=1400
+
+# Finite cyclic group for EAP-pwd. Number maps to group of domain parameters
+# using the IANA repository for IKE (RFC 2409).
+#pwd_group=19
+
# Configuration data for EAP-SIM database/authentication gateway interface.
# This is a text string in implementation specific format. The example
# implementation in eap_sim_db.c uses this as the UNIX domain socket name for
# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:"
-# prefix.
+# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config),
+# database file can be described with an optional db=<path> parameter.
#eap_sim_db=unix:/tmp/hlr_auc_gw.sock
+#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db
# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret,
# random value. It is configured as a 16-octet value in hex format. It can be
# 60 (1 minute).
#radius_acct_interim_interval=600
+# Request Chargeable-User-Identity (RFC 4372)
+# This parameter can be used to configure hostapd to request CUI from the
+# RADIUS server by including Chargeable-User-Identity attribute into
+# Access-Request packets.
+#radius_request_cui=1
+
# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN
# is used for the stations. This information is parsed from following RADIUS
# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN),
# to the bridge.
#vlan_tagged_interface=eth0
+# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs
+# to know how to name it.
+# 0 = vlan<XXX>, e.g., vlan1
+# 1 = <vlan_tagged_interface>.<XXX>, e.g. eth0.1
+#vlan_naming=0
+
+# Arbitrary RADIUS attributes can be added into Access-Request and
+# Accounting-Request packets by specifying the contents of the attributes with
+# the following configuration parameters. There can be multiple of these to
+# add multiple attributes. These parameters can also be used to override some
+# of the attributes added automatically by hostapd.
+# Format: <attr_id>[:<syntax:value>]
+# attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific)
+# syntax: s = string (UTF-8), d = integer, x = octet string
+# value: attribute value in format indicated by the syntax
+# If syntax and value parts are omitted, a null value (single 0x00 octet) is
+# used.
+#
+# Additional Access-Request attributes
+# radius_auth_req_attr=<attr_id>[:<syntax:value>]
+# Examples:
+# Operator-Name = "Operator"
+#radius_auth_req_attr=126:s:Operator
+# Service-Type = Framed (2)
+#radius_auth_req_attr=6:d:2
+# Connect-Info = "testing" (this overrides the automatically generated value)
+#radius_auth_req_attr=77:s:testing
+# Same Connect-Info value set as a hexdump
+#radius_auth_req_attr=77:x:74657374696e67
+
+#
+# Additional Accounting-Request attributes
+# radius_acct_req_attr=<attr_id>[:<syntax:value>]
+# Examples:
+# Operator-Name = "Operator"
+#radius_acct_req_attr=126:s:Operator
+
+# Dynamic Authorization Extensions (RFC 5176)
+# This mechanism can be used to allow dynamic changes to user session based on
+# commands from a RADIUS server (or some other disconnect client that has the
+# needed session information). For example, Disconnect message can be used to
+# request an associated station to be disconnected.
+#
+# This is disabled by default. Set radius_das_port to non-zero UDP port
+# number to enable.
+#radius_das_port=3799
+#
+# DAS client (the host that can send Disconnect/CoA requests) and shared secret
+#radius_das_client=192.168.1.123 shared secret here
+#
+# DAS Event-Timestamp time window in seconds
+#radius_das_time_window=300
+#
+# DAS require Event-Timestamp
+#radius_das_require_event_timestamp=1
##### RADIUS authentication server configuration ##############################
# Enable WPA. Setting this variable configures the AP to require WPA (either
# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either
# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.
+# Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice.
# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
# RADIUS authentication server must be configured, and WPA-EAP must be included
# in wpa_key_mgmt.
# configuration reloads.
#wpa_psk_file=/etc/hostapd.wpa_psk
+# Optionally, WPA passphrase can be received from RADIUS authentication server
+# This requires macaddr_acl to be set to 2 (RADIUS)
+# 0 = disabled (default)
+# 1 = optional; use default passphrase/psk if RADIUS server does not include
+# Tunnel-Password
+# 2 = required; reject authentication if RADIUS server does not include
+# Tunnel-Password
+#wpa_psk_radius=0
+
# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be
# added to enable SHA256-based stronger algorithms.
# dot11AssociationSAQueryRetryTimeout, 1...4294967295
#assoc_sa_query_retry_timeout=201
+# disable_pmksa_caching: Disable PMKSA caching
+# This parameter can be used to disable caching of PMKSA created through EAP
+# authentication. RSN preauthentication may still end up using PMKSA caching if
+# it is enabled (rsn_preauth=1).
+# 0 = PMKSA caching enabled (default)
+# 1 = PMKSA caching disabled
+#disable_pmksa_caching=0
# okc: Opportunistic Key Caching (aka Proactive Key Caching)
# Allow PMK cache to be shared opportunistically among configured interfaces
# And so on.. One line per R0KH.
# List of R1KHs in the same Mobility Domain
-# format: <MAC address> <R0KH-ID> <128-bit key as hex string>
+# format: <MAC address> <R1KH-ID> <128-bit key as hex string>
# This list is used to map R1KH-ID to a destination MAC address when sending
# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD
# that can request PMK-R1 keys.
# Config Methods
# List of the supported configuration methods
-#config_methods=label display push_button keypad
-
-# Access point PIN for initial configuration and adding Registrars
+# Available methods: usba ethernet label display ext_nfc_token int_nfc_token
+# nfc_interface push_button keypad virtual_display physical_display
+# virtual_push_button physical_push_button
+#config_methods=label virtual_display virtual_push_button keypad
+
+# WPS capability discovery workaround for PBC with Windows 7
+# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting
+# as a Registrar and using M1 from the AP. The config methods attribute in that
+# message is supposed to indicate only the configuration method supported by
+# the AP in Enrollee role, i.e., to add an external Registrar. For that case,
+# PBC shall not be used and as such, the PushButton config method is removed
+# from M1 by default. If pbc_in_m1=1 is included in the configuration file,
+# the PushButton config method is left in M1 (if included in config_methods
+# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label
+# in the AP).
+#pbc_in_m1=1
+
+# Static access point PIN for initial configuration and adding Registrars
# If not set, hostapd will not allow external WPS Registrars to control the
-# access point.
+# access point. The AP PIN can also be set at runtime with hostapd_cli
+# wps_ap_pin command. Use of temporary (enabled by user action) and random
+# AP PIN is much more secure than configuring a static AP PIN here. As such,
+# use of the ap_pin parameter is not recommended if the AP device has means for
+# displaying a random PIN.
#ap_pin=12345670
# Skip building of automatic WPS credential
# 12-digit, all-numeric code that identifies the consumer package.
#upc=123456789012
+# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band)
+# This value should be set according to RF band(s) supported by the AP if
+# hw_mode is not set. For dual band dual concurrent devices, this needs to be
+# set to ag to allow both RF bands to be advertized.
+#wps_rf_bands=ag
+
+# NFC password token for WPS
+# These parameters can be used to configure a fixed NFC password token for the
+# AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When
+# these parameters are used, the AP is assumed to be deployed with a NFC tag
+# that includes the matching NFC password token (e.g., written based on the
+# NDEF record from nfc_pw_token).
+#
+#wps_nfc_dev_pw_id: Device Password ID (16..65535)
+#wps_nfc_dh_pubkey: Hexdump of DH Public Key
+#wps_nfc_dh_privkey: Hexdump of DH Private Key
+#wps_nfc_dev_pw: Hexdump of Device Password
+
+##### Wi-Fi Direct (P2P) ######################################################
+
+# Enable P2P Device management
+#manage_p2p=1
+
+# Allow cross connection
+#allow_cross_connection=1
+
+#### TDLS (IEEE 802.11z-2010) #################################################
+
+# Prohibit use of TDLS in this BSS
+#tdls_prohibit=1
+
+# Prohibit use of TDLS Channel Switching in this BSS
+#tdls_prohibit_chan_switch=1
+
+##### IEEE 802.11v-2011 #######################################################
+
+# Time advertisement
+# 0 = disabled (default)
+# 2 = UTC time at which the TSF timer is 0
+#time_advertisement=2
+
+# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004:
+# stdoffset[dst[offset][,start[/time],end[/time]]]
+#time_zone=EST5
+
+# WNM-Sleep Mode (extended sleep mode for stations)
+# 0 = disabled (default)
+# 1 = enabled (allow stations to use WNM-Sleep Mode)
+#wnm_sleep_mode=1
+
+# BSS Transition Management
+# 0 = disabled (default)
+# 1 = enabled
+#bss_transition=1
+
+##### IEEE 802.11u-2011 #######################################################
+
+# Enable Interworking service
+#interworking=1
+
+# Access Network Type
+# 0 = Private network
+# 1 = Private network with guest access
+# 2 = Chargeable public network
+# 3 = Free public network
+# 4 = Personal device network
+# 5 = Emergency services only network
+# 14 = Test or experimental
+# 15 = Wildcard
+#access_network_type=0
+
+# Whether the network provides connectivity to the Internet
+# 0 = Unspecified
+# 1 = Network provides connectivity to the Internet
+#internet=1
+
+# Additional Step Required for Access
+# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if
+# RSN is used.
+#asra=0
+
+# Emergency services reachable
+#esr=0
+
+# Unauthenticated emergency service accessible
+#uesa=0
+
+# Venue Info (optional)
+# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34.
+# Example values (group,type):
+# 0,0 = Unspecified
+# 1,7 = Convention Center
+# 1,13 = Coffee Shop
+# 2,0 = Unspecified Business
+# 7,1 Private Residence
+#venue_group=7
+#venue_type=1
+
+# Homogeneous ESS identifier (optional; dot11HESSID)
+# If set, this shall be identifical to one of the BSSIDs in the homogeneous
+# ESS and this shall be set to the same value across all BSSs in homogeneous
+# ESS.
+#hessid=02:03:04:05:06:07
+
+# Roaming Consortium List
+# Arbitrary number of Roaming Consortium OIs can be configured with each line
+# adding a new OI to the list. The first three entries are available through
+# Beacon and Probe Response frames. Any additional entry will be available only
+# through ANQP queries. Each OI is between 3 and 15 octets and is configured as
+# a hexstring.
+#roaming_consortium=021122
+#roaming_consortium=2233445566
+
+# Venue Name information
+# This parameter can be used to configure one or more Venue Name Duples for
+# Venue Name ANQP information. Each entry has a two or three character language
+# code (ISO-639) separated by colon from the venue name string.
+# Note that venue_group and venue_type have to be set for Venue Name
+# information to be complete.
+#venue_name=eng:Example venue
+#venue_name=fin:Esimerkkipaikka
+
+# Network Authentication Type
+# This parameter indicates what type of network authentication is used in the
+# network.
+# format: <network auth type indicator (1-octet hex str)> [redirect URL]
+# Network Authentication Type Indicator values:
+# 00 = Acceptance of terms and conditions
+# 01 = On-line enrollment supported
+# 02 = http/https redirection
+# 03 = DNS redirection
+#network_auth_type=00
+#network_auth_type=02http://www.example.com/redirect/me/here/
+
+# IP Address Type Availability
+# format: <1-octet encoded value as hex str>
+# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3)
+# ipv4_type:
+# 0 = Address type not available
+# 1 = Public IPv4 address available
+# 2 = Port-restricted IPv4 address available
+# 3 = Single NATed private IPv4 address available
+# 4 = Double NATed private IPv4 address available
+# 5 = Port-restricted IPv4 address and single NATed IPv4 address available
+# 6 = Port-restricted IPv4 address and double NATed IPv4 address available
+# 7 = Availability of the address type is not known
+# ipv6_type:
+# 0 = Address type not available
+# 1 = Address type available
+# 2 = Availability of the address type not known
+#ipaddr_type_availability=14
+
+# Domain Name
+# format: <variable-octet str>[,<variable-octet str>]
+#domain_name=example.com,another.example.com,yet-another.example.com
+
+# 3GPP Cellular Network information
+# format: <MCC1,MNC1>[;<MCC2,MNC2>][;...]
+#anqp_3gpp_cell_net=244,91;310,026;234,56
+
+# NAI Realm information
+# One or more realm can be advertised. Each nai_realm line adds a new realm to
+# the set. These parameters provide information for stations using Interworking
+# network selection to allow automatic connection to a network based on
+# credentials.
+# format: <encoding>,<NAI Realm(s)>[,<EAP Method 1>][,<EAP Method 2>][,...]
+# encoding:
+# 0 = Realm formatted in accordance with IETF RFC 4282
+# 1 = UTF-8 formatted character string that is not formatted in
+# accordance with IETF RFC 4282
+# NAI Realm(s): Semi-colon delimited NAI Realm(s)
+# EAP Method: <EAP Method>[:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...]
+# AuthParam (Table 8-188 in IEEE Std 802.11-2012):
+# ID 2 = Non-EAP Inner Authentication Type
+# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2
+# ID 3 = Inner authentication EAP Method Type
+# ID 5 = Credential Type
+# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token,
+# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous,
+# 10 = Vendor Specific
+#nai_realm=0,example.com;example.net
+# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with
+# username/password
+#nai_realm=0,example.org,13[5:6],21[2:4][5:7]
+
+##### Hotspot 2.0 #############################################################
+
+# Enable Hotspot 2.0 support
+#hs20=1
+
+# Disable Downstream Group-Addressed Forwarding (DGAF)
+# This can be used to configure a network where no group-addressed frames are
+# allowed. The AP will not forward any group-address frames to the stations and
+# random GTKs are issued for each station to prevent associated stations from
+# forging such frames to other stations in the BSS.
+#disable_dgaf=1
+
+# Operator Friendly Name
+# This parameter can be used to configure one or more Operator Friendly Name
+# Duples. Each entry has a two or three character language code (ISO-639)
+# separated by colon from the operator friendly name string.
+#hs20_oper_friendly_name=eng:Example operator
+#hs20_oper_friendly_name=fin:Esimerkkioperaattori
+
+# Connection Capability
+# This can be used to advertise what type of IP traffic can be sent through the
+# hotspot (e.g., due to firewall allowing/blocking protocols/ports).
+# format: <IP Protocol>:<Port Number>:<Status>
+# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP
+# Port Number: 0..65535
+# Status: 0 = Closed, 1 = Open, 2 = Unknown
+# Each hs20_conn_capab line is added to the list of advertised tuples.
+#hs20_conn_capab=1:0:2
+#hs20_conn_capab=6:22:1
+#hs20_conn_capab=17:5060:0
+
+# WAN Metrics
+# format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD>
+# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity
+# (encoded as two hex digits)
+# Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state
+# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps;
+# 1..4294967295; 0 = unknown
+# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps
+# 1..4294967295; 0 = unknown
+# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%)
+# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%)
+# Load Measurement Duration: Duration for measuring downlink/uplink load in
+# tenths of a second (1..65535); 0 if load cannot be determined
+#hs20_wan_metrics=01:8000:1000:80:240:3000
+
+# Operating Class Indication
+# List of operating classes the BSSes in this ESS use. The Global operating
+# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that
+# can be used in this.
+# format: hexdump of operating class octets
+# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz
+# channels 36-48):
+#hs20_operating_class=5173
+
##### Multiple BSSID support ##################################################
#
# Above configuration is using the default interface (wlan#, or multi-SSID VLAN
projects / thirdparty / hostap.git / blobdiff