wmm_ac_vo_acm=0
# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102
+# Enable Multi-AP functionality
+# 0 = disabled (default)
+# 1 = AP support backhaul BSS
+# 2 = AP support fronthaul BSS
+# 3 = AP supports both backhaul BSS and fronthaul BSS
+#multi_ap=0
+
# Static WEP key configuration
#
# The key number to use when transmitting.
# unsigned integer = duration in units of 16 us
#he_rts_threshold=0
+#he_mu_edca_qos_info_param_count
+#he_mu_edca_qos_info_q_ack
+#he_mu_edca_qos_info_queue_request=1
+#he_mu_edca_qos_info_txop_request
+#he_mu_edca_ac_be_aifsn=0
+#he_mu_edca_ac_be_ecwmin=15
+#he_mu_edca_ac_be_ecwmax=15
+#he_mu_edca_ac_be_timer=255
+#he_mu_edca_ac_bk_aifsn=0
+#he_mu_edca_ac_bk_aci=1
+#he_mu_edca_ac_bk_ecwmin=15
+#he_mu_edca_ac_bk_ecwmax=15
+#he_mu_edca_ac_bk_timer=255
+#he_mu_edca_ac_vi_ecwmin=15
+#he_mu_edca_ac_vi_ecwmax=15
+#he_mu_edca_ac_vi_aifsn=0
+#he_mu_edca_ac_vi_aci=2
+#he_mu_edca_ac_vi_timer=255
+#he_mu_edca_ac_vo_aifsn=0
+#he_mu_edca_ac_vo_aci=3
+#he_mu_edca_ac_vo_ecwmin=15
+#he_mu_edca_ac_vo_ecwmax=15
+#he_mu_edca_ac_vo_timer=255
+
##### IEEE 802.1X-2004 related configuration ##################################
# Require IEEE 802.1X authorization
# valid CRL signed by the CA is required to be included in the ca_cert file.
# This can be done by using PEM format for CA certificate and CRL and
# concatenating these into one file. Whenever CRL changes, hostapd needs to be
-# restarted to take the new CRL into use.
+# restarted to take the new CRL into use. Alternatively, crl_reload_interval can
+# be used to configure periodic updating of the loaded CRL information.
# 0 = do not verify CRLs (default)
# 1 = check the CRL of the user certificate
# 2 = check all CRLs in the certificate path
#check_crl=1
+# Specify whether to ignore certificate CRL validity time mismatches with
+# errors X509_V_ERR_CERT_HAS_EXPIRED and X509_V_ERR_CERT_NOT_YET_VALID.
+#
+# 0 = ignore errors
+# 1 = do not ignore errors (default)
+#check_crl_strict=1
+
+# CRL reload interval in seconds
+# This can be used to reload ca_cert file and the included CRL on every new TLS
+# session if difference between last reload and the current reload time in
+# seconds is greater than crl_reload_interval.
+# Note: If interval time is very short, CPU overhead may be negatively affected
+# and it is advised to not go below 300 seconds.
+# This is applicable only with check_crl values 1 and 2.
+# 0 = do not reload CRLs (default)
+# crl_reload_interval = 300
+
# TLS Session Lifetime in seconds
# This can be used to allow TLS sessions to be cached and resumed with an
# abbreviated handshake when using EAP-TLS/TTLS/PEAP.
# (default: 0 = session caching and resumption disabled)
#tls_session_lifetime=3600
+# TLS flags
+# [ALLOW-SIGN-RSA-MD5] = allow MD5-based certificate signatures (depending on
+# the TLS library, these may be disabled by default to enforce stronger
+# security)
+# [DISABLE-TIME-CHECKS] = ignore certificate validity time (this requests
+# the TLS library to accept certificates even if they are not currently
+# valid, i.e., have expired or have not yet become valid; this should be
+# used only for testing purposes)
+# [DISABLE-TLSv1.0] = disable use of TLSv1.0
+# [ENABLE-TLSv1.0] = explicitly enable use of TLSv1.0 (this allows
+# systemwide TLS policies to be overridden)
+# [DISABLE-TLSv1.1] = disable use of TLSv1.1
+# [ENABLE-TLSv1.1] = explicitly enable use of TLSv1.1 (this allows
+# systemwide TLS policies to be overridden)
+# [DISABLE-TLSv1.2] = disable use of TLSv1.2
+# [ENABLE-TLSv1.2] = explicitly enable use of TLSv1.2 (this allows
+# systemwide TLS policies to be overridden)
+# [DISABLE-TLSv1.3] = disable use of TLSv1.3
+# [ENABLE-TLSv1.3] = enable TLSv1.3 (experimental - disabled by default)
+#tls_flags=[flag1][flag2]...
+
# Cached OCSP stapling response (DER encoded)
# If set, this file is sent as a certificate status response by the EAP server
# if the EAP peer requests certificate status in the ClientHello message.
# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value
# VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can
# be used to set static client MAC address to VLAN ID mapping.
-# 0 = disabled (default)
-# 1 = option; use default interface if RADIUS server does not include VLAN ID
+# 0 = disabled (default); only VLAN IDs from accept_mac_file will be used
+# 1 = optional; use default interface if RADIUS server does not include VLAN ID
# 2 = required; reject authentication if RADIUS server does not include VLAN ID
#dynamic_vlan=0
# white space (space or tab).
# If no entries are provided by this file, the station is statically mapped
# to <bss-iface>.<vlan-id> interfaces.
+# Each line can optionally also contain the name of a bridge to add the VLAN to
#vlan_file=/etc/hostapd.vlan
# Interface where 802.1q tagged packets should appear when a RADIUS server is
# and/or WPA2 (full IEEE 802.11i/RSN):
# bit0 = WPA
# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
-#wpa=1
+# Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2.
+# In other words, for WPA3, wpa=2 is used the configuration (and
+# wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK).
+#wpa=2
# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit
# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase
# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be
# added to enable SHA256-based stronger algorithms.
+# WPA-PSK = WPA-Personal / WPA2-Personal
+# WPA-PSK-SHA256 = WPA2-Personal using SHA256
+# WPA-EAP = WPA-Enterprise / WPA2-Enterprise
+# WPA-EAP-SHA256 = WPA2-Enterprise using SHA256
+# SAE = SAE (WPA3-Personal)
+# WPA-EAP-SUITE-B-192 = WPA3-Enterprise with 192-bit security/CNSA suite
+# FT-PSK = FT with passphrase/PSK
+# FT-EAP = FT with EAP
+# FT-EAP-SHA384 = FT with EAP using SHA384
+# FT-SAE = FT with SAE
# FILS-SHA256 = Fast Initial Link Setup with SHA256
# FILS-SHA384 = Fast Initial Link Setup with SHA384
# FT-FILS-SHA256 = FT and Fast Initial Link Setup with SHA256
# FT-FILS-SHA384 = FT and Fast Initial Link Setup with SHA384
+# OWE = Opportunistic Wireless Encryption (a.k.a. Enhanced Open)
+# DPP = Device Provisioning Protocol
+# OSEN = Hotspot 2.0 online signup with encryption
# (dot11RSNAConfigAuthenticationSuitesTable)
#wpa_key_mgmt=WPA-PSK WPA-EAP
# dot11AssociationSAQueryRetryTimeout, 1...4294967295
#assoc_sa_query_retry_timeout=201
+# ocv: Operating Channel Validation
+# This is a countermeasure against multi-channel man-in-the-middle attacks.
+# Enabling this automatically also enables ieee80211w, if not yet enabled.
+# 0 = disabled (default)
+# 1 = enabled
+#ocv=1
+
# disable_pmksa_caching: Disable PMKSA caching
# This parameter can be used to disable caching of PMKSA created through EAP
# authentication. RSN preauthentication may still end up using PMKSA caching if
# OSU Providers
# One or more sets of following parameter. Each OSU provider is started by the
# mandatory osu_server_uri item. The other parameters add information for the
-# last added OSU provider.
+# last added OSU provider. osu_nai specifies the OSU_NAI value for OSEN
+# authentication when using a standalone OSU BSS. osu_nai2 specifies the OSU_NAI
+# value for OSEN authentication when using a shared BSS (Single SSID) for OSU.
#
#osu_server_uri=https://example.com/osu/
#osu_friendly_name=eng:Example operator
#osu_friendly_name=fin:Esimerkkipalveluntarjoaja
#osu_nai=anonymous@example.com
+#osu_nai2=anonymous@example.com
#osu_method_list=1 0
#osu_icon=icon32
#osu_icon=icon64
# Default is 0 = OCE disabled
#oce=0
+# RSSI-based assocition rejection
+#
+# Reject STA association if RSSI is below given threshold (in dBm)
+# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled)
+# Note: This rejection happens based on a signal strength detected while
+# receiving a single frame and as such, there is significant risk of the value
+# not being accurate and this resulting in valid stations being rejected. As
+# such, this functionality is not recommended to be used for purposes other than
+# testing.
+#rssi_reject_assoc_rssi=-75
+#
+# Association retry delay in seconds allowed by the STA if RSSI has not met the
+# threshold (range: 0..255, default=30).
+#rssi_reject_assoc_timeout=30
+
##### Fast Session Transfer (FST) support #####################################
#
# The options in this section are only available when the build configuration
projects / thirdparty / hostap.git / blobdiff