* MPC8xx Communication Processor Module.
* Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
*
+ * (C) Copyright 2000-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
* This file contains structures and information for the communication
* processor channels. Some CPM control and status is available
* throught the MPC8xx internal memory map. See immap.h for details.
* CPM capabilities. I (or someone else) will add definitions as they
* are needed. -- Dan
*
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space. The remaining DP RAM is available for buffer descriptors
- * or other use.
*/
#ifndef __CPM_8XX__
#define __CPM_8XX__
-#include <linux/config.h>
#include <asm/8xx_immap.h>
/* CPM Command register.
*/
-#define CPM_CR_RST ((ushort)0x8000)
-#define CPM_CR_OPCODE ((ushort)0x0f00)
-#define CPM_CR_CHAN ((ushort)0x00f0)
-#define CPM_CR_FLG ((ushort)0x0001)
+#define CPM_CR_RST ((ushort)0x8000)
+#define CPM_CR_OPCODE ((ushort)0x0f00)
+#define CPM_CR_CHAN ((ushort)0x00f0)
+#define CPM_CR_FLG ((ushort)0x0001)
/* Some commands (there are more...later)
*/
/* Channel numbers.
*/
-#define CPM_CR_CH_SCC1 ((ushort)0x0000)
-#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
-#define CPM_CR_CH_SCC2 ((ushort)0x0004)
-#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI / IDMA2 / Timers */
-#define CPM_CR_CH_SCC3 ((ushort)0x0008)
-#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
-#define CPM_CR_CH_SCC4 ((ushort)0x000c)
-#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
+#define CPM_CR_CH_SCC1 ((ushort)0x0000)
+#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
+#define CPM_CR_CH_SCC2 ((ushort)0x0004)
+#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI/IDMA2/Timers */
+#define CPM_CR_CH_SCC3 ((ushort)0x0008)
+#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
+#define CPM_CR_CH_SCC4 ((ushort)0x000c)
+#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
/*
* DPRAM defines and allocation functions
*/
-
-/* The dual ported RAM is multi-functional. Some areas can be (and are
- * being) used for microcode. There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#ifdef CFG_ALLOC_DPRAM
-
-#define CPM_DATAONLY_BASE ((uint)0x0800)
-#define CPM_DATAONLY_SIZE ((uint)0x0700)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-
-#else
-
#define CPM_SERIAL_BASE 0x0800
#define CPM_I2C_BASE 0x0820
#define CPM_SPI_BASE 0x0840
#define CPM_FEC_BASE 0x0860
-#define CPM_WLKBD_BASE 0x0880
+#define CPM_SERIAL2_BASE 0x08E0
#define CPM_SCC_BASE 0x0900
#define CPM_POST_BASE 0x0980
+#define CPM_WLKBD_BASE 0x0a00
+#ifndef CONFIG_SYS_CPM_POST_WORD_ADDR
+#define CPM_POST_WORD_ADDR 0x07FC
+#else
+#define CPM_POST_WORD_ADDR CONFIG_SYS_CPM_POST_WORD_ADDR
#endif
-#define CPM_POST_WORD_ADDR 0x07FC
+#ifndef CONFIG_SYS_CPM_BOOTCOUNT_ADDR
+#define CPM_BOOTCOUNT_ADDR (CPM_POST_WORD_ADDR - 2*sizeof(ulong))
+#else
+#define CPM_BOOTCOUNT_ADDR CONFIG_SYS_CPM_BOOTCOUNT_ADDR
+#endif
#define BD_IIC_START ((uint) 0x0400) /* <- please use CPM_I2C_BASE !! */
uint cbd_bufaddr; /* Buffer address in host memory */
} cbd_t;
-#define BD_SC_EMPTY ((ushort)0x8000) /* Recieve is empty */
+#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
*/
#define PROFF_SCC1 ((uint)0x0000)
#define PROFF_IIC ((uint)0x0080)
+#define PROFF_REVNUM ((uint)0x00b0)
#define PROFF_SCC2 ((uint)0x0100)
#define PROFF_SPI ((uint)0x0180)
#define PROFF_SCC3 ((uint)0x0200)
#define PROFF_SMC2 ((uint)0x0380)
/* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
*/
typedef struct smc_uart {
ushort smc_rbase; /* Rx Buffer descriptor base address */
ushort smc_brkec; /* rcv'd break condition counter */
ushort smc_brkcr; /* xmt break count register */
ushort smc_rmask; /* Temporary bit mask */
+ u_char res1[8];
+ ushort smc_rpbase; /* Relocation pointer */
} smc_uart_t;
/* Function code bits.
* #define FEC_ENET to enable the SCC resp. FEC ethernet drivers.
**********************************************************************/
-
-/*** ADS *************************************************************/
-
-#if defined(CONFIG_MPC860) && defined(CONFIG_ADS)
-/* This ENET stuff is for the MPC860ADS with ethernet on SCC1.
- */
-
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0200)
-
-#define PB_ENET_TENA ((uint)0x00001000)
-
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002c)
-
-/* 68160 PHY control */
-
-#define PC_ENET_ETHLOOP ((ushort)0x0800)
-#define PC_ENET_TPFLDL ((ushort)0x0400)
-#define PC_ENET_TPSQEL ((ushort)0x0200)
-
-#endif /* MPC860ADS */
-
-/*** AMX860 **********************************************/
-
-#if defined(CONFIG_AMX860)
-
-/* This ENET stuff is for the AMX860 with ethernet on SCC1.
- */
-
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0400)
-#define PA_ENET_RCLK ((ushort)0x0800)
-
-#define PB_ENET_TENA ((uint)0x00001000)
-
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003e)
-
-/* 68160 PHY control */
-
-#define PB_ENET_ETHLOOP ((uint)0x00020000)
-#define PB_ENET_TPFLDL ((uint)0x00010000)
-#define PB_ENET_TPSQEL ((uint)0x00008000)
-#define PD_ENET_ETH_EN ((ushort)0x0004)
-
-#endif /* CONFIG_AMX860 */
-
/*** BSEIP **********************************************************/
#ifdef CONFIG_BSEIP
#define SICR_ENET_CLKRT ((uint)0x00002c00)
#endif /* CONFIG_BSEIP */
-/*** BSEIP **********************************************************/
-
-#ifdef CONFIG_FLAGADM
-/* Enet configuration for the FLAGADM */
-/* Enet on SCC2 */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0400)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003400)
-#endif /* CONFIG_FLAGADM */
-
-/*** C2MON **********************************************************/
-
-#ifdef CONFIG_C2MON
-
-# ifndef CONFIG_FEC_ENET /* use SCC for 10Mbps Ethernet */
-# error "Ethernet on SCC not supported on C2MON Board!"
-# else /* Use FEC for Fast Ethernet */
-
-#undef SCC_ENET
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_C2MON */
-
-/*********************************************************************/
-
-
-/*** CCM and PCU E ***********************************************/
-
-/* The PCU E and CCM use the FEC on a MPC860T for Ethernet */
-
-#if defined (CONFIG_PCU_E) || defined(CONFIG_CCM)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_PCU_E, CONFIG_CCM */
-
-/*** ESTEEM 192E **************************************************/
-#ifdef CONFIG_ESTEEM192E
-/* ESTEEM192E
- * This ENET stuff is for the MPC850 with ethernet on SCC2. This
- * is very similar to the RPX-Lite configuration.
- * Note TENA , LOOPBACK , FDPLEX_DIS on Port B.
- */
-
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003d00)
-
-#define PB_ENET_LOOPBACK ((uint)0x00004000)
-#define PB_ENET_FDPLEX_DIS ((uint)0x00008000)
-
-#endif
-
-/*** FADS823 ********************************************************/
-
-#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC823FADS with ethernet on SCC2.
- */
-#ifdef CONFIG_SCC2_ENET
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define CPMVEC_ENET CPMVEC_SCC2
-#endif
-
-#ifdef CONFIG_SCC1_ENET
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define CPMVEC_ENET CPMVEC_SCC1
-#endif
-
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0400)
-#define PA_ENET_RCLK ((ushort)0x0200)
-
-#define PB_ENET_TENA ((uint)0x00002000)
-
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002e00)
-
-#endif /* CONFIG_FADS823FADS */
-
-/*** FADS850SAR ********************************************************/
-
-#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC850SAR with ethernet on SCC2. Some of
- * this may be unique to the FADS850SAR configuration.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00) /* RCLK-CLK2, TCLK-CLK4 */
-#endif /* CONFIG_FADS850SAR */
-
-/*** FADS860T********************************************************/
-
-#if defined(CONFIG_MPC860T) && defined(CONFIG_FADS)
-/* This ENET stuff is for the MPC860TFADS with ethernet on SCC1.
- */
-
-#ifdef CONFIG_SCC1_ENET
-#define SCC_ENET 0
-#endif /* CONFIG_SCC1_ETHERNET */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0200)
-
-#define PB_ENET_TENA ((uint)0x00001000)
-
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002c)
-
-/* This ENET stuff is for the MPC860TFADS with ethernet on FEC.
- */
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_FADS860T */
-
-/*** FPS850L, FPS860L ************************************************/
-
-#if defined(CONFIG_FPS850L) || defined(CONFIG_FPS860L)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-#endif /* CONFIG_FPS850L, CONFIG_FPS860L */
-
-/*** GEN860T **********************************************************/
-#if defined(CONFIG_GEN860T)
-#undef SCC_ENET
-#define FEC_ENET
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3-15 */
-#endif /* CONFIG_GEN860T */
-
-/*** GENIETV ********************************************************/
-
-#if defined(CONFIG_GENIETV)
-/* Ethernet is only on SCC2 */
-
-#define CONFIG_SCC2_ENET
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define CPMVEC_ENET CPMVEC_SCC2
-
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002e00)
-
-#endif /* CONFIG_GENIETV */
-
-/*** GTH ******************************************************/
-
-#ifdef CONFIG_GTH
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-/* This ENET stuff is for GTH 10 Mbit ( SCC ) */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-
-#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */
-#define PA_ENET_RCLK ((ushort)0x0400) /* PA5 */
-
-#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */
-
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */
-
-/* NOTE. This is reset for 10Mbit port only */
-#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 */
-
-#define SICR_ENET_MASK ((uint)0x000000ff)
-
-/* TCLK PA4 -->CLK4, RCLK PA5 -->CLK3 */
-#define SICR_ENET_CLKRT ((uint)0x00000037)
-
-#endif /* CONFIG_GTH */
-
-/*** HERMES-PRO ******************************************************/
-
-/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
-
-#ifdef CONFIG_HERMES
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_HERMES */
-
-/*** IAD210 **********************************************************/
-
-/* The IAD210 uses the FEC on a MPC860P for Ethernet */
-
-#if defined(CONFIG_IAD210)
-
-# define FEC_ENET /* use FEC for Ethernet */
-# undef SCC_ENET
-
-# define PD_MII_TXD1 ((ushort) 0x1000 ) /* PD 3 */
-# define PD_MII_TXD2 ((ushort) 0x0800 ) /* PD 4 */
-# define PD_MII_TXD3 ((ushort) 0x0400 ) /* PD 5 */
-# define PD_MII_RX_DV ((ushort) 0x0200 ) /* PD 6 */
-# define PD_MII_RX_ERR ((ushort) 0x0100 ) /* PD 7 */
-# define PD_MII_RX_CLK ((ushort) 0x0080 ) /* PD 8 */
-# define PD_MII_TXD0 ((ushort) 0x0040 ) /* PD 9 */
-# define PD_MII_RXD0 ((ushort) 0x0020 ) /* PD 10 */
-# define PD_MII_TX_ERR ((ushort) 0x0010 ) /* PD 11 */
-# define PD_MII_MDC ((ushort) 0x0008 ) /* PD 12 */
-# define PD_MII_RXD1 ((ushort) 0x0004 ) /* PD 13 */
-# define PD_MII_RXD2 ((ushort) 0x0002 ) /* PD 14 */
-# define PD_MII_RXD3 ((ushort) 0x0001 ) /* PD 15 */
-
-# define PD_MII_MASK ((ushort) 0x1FFF ) /* PD 3...15 */
-
-#endif /* CONFIG_IAD210 */
-
-/*** ICU862 **********************************************************/
-
-#if defined(CONFIG_ICU862)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for EThernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_ICU862 */
-
-/*** IP860 **********************************************************/
-
-#if defined(CONFIG_IP860)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0100) /* PA 7 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-#define PB_ENET_RESET (uint)0x00000008 /* PB 28 */
-#define PB_ENET_JABD (uint)0x00000004 /* PB 29 */
-
-/* Control bits in the SICR to route TCLK (CLK1) and RCLK (CLK2) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000002C)
-#endif /* CONFIG_IP860 */
-
-/*** IVMS8 **********************************************************/
-
-/* The IVMS8 uses the FEC on a MPC860T for Ethernet */
-
-#if defined(CONFIG_IVMS8) || defined(CONFIG_IVML24)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
-
-#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
-
-/*** KUP4K *********************************************************/
-/* The KUP4K uses the FEC on a MPC855T for Ethernet */
-
-#if defined(CONFIG_KUP4K)
-
-#define FEC_ENET /* use FEC for EThernet */
-#undef SCC_ENET
-
-#define PB_ENET_POWER ((uint)0x00010000) /* PB 15 */
-
-#define PC_ENET_RESET ((ushort)0x0010) /* PC 11 */
-
-#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */
-#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */
-#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */
-#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */
-#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */
-#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */
-#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */
-#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */
-#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */
-#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */
-#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */
-#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */
-#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */
-
-#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
-
-#endif /* CONFIG_KUP4K */
-
-
-/*** LANTEC *********************************************************/
-
-#if defined(CONFIG_LANTEC) && CONFIG_LANTEC >= 2
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_LBK ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000FF00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_LANTEC v2 */
-
-/*** LWMON **********************************************************/
-
-#if defined(CONFIG_LWMON) && !defined(CONFIG_8xx_CONS_SCC2)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003E00)
-#endif /* CONFIG_LWMON */
-
-/*** NX823 ***********************************************/
-
-#if defined(CONFIG_NX823)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00)
-
-#endif /* CONFIG_NX823 */
-
-/*** MBX ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use. The TCLK and RCLK seem unique
- * to the MBX860 board. Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PC_ENET_TENA ((ushort)0x0001)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-#endif /* CONFIG_MBX */
-
-/*** MHPC ********************************************************/
-
-#if defined(CONFIG_MHPC)
-/* This ENET stuff is for the MHPC with ethernet on SCC2.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002e00) /* RCLK-CLK2, TCLK-CLK3 */
-#endif /* CONFIG_MHPC */
-
-/*** RPXCLASSIC *****************************************************/
-
-#ifdef CONFIG_RPXCLASSIC
-
-#ifdef CONFIG_FEC_ENET
-
-# define FEC_ENET /* use FEC for EThernet */
-# undef SCC_ENET
-
-#else /* ! CONFIG_FEC_ENET */
-
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00001000)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-
-#endif /* CONFIG_FEC_ENET */
-
-#endif /* CONFIG_RPXCLASSIC */
-
-/*** RPXLITE ********************************************************/
-
-#ifdef CONFIG_RPXLITE
-/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of
- * this may be unique to the RPX-Lite configuration.
- * Note TENA is on Port B.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003d00)
-#endif /* CONFIG_RPXLITE */
+/*** KM8XX *********************************************************/
-/*** SM850 *********************************************************/
+/* The KM8XX Service Module uses SCC3 for Ethernet */
-/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
-
-#ifdef CONFIG_SM850
+#ifdef CONFIG_KM8XX
#define PROFF_ENET PROFF_SCC3 /* Ethernet on SCC3 */
#define CPM_CR_ENET CPM_CR_CH_SCC3
#define SCC_ENET 2
-#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
-#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
+#define PA_ENET_RXD ((ushort)0x0010) /* PA 11 */
+#define PA_ENET_TXD ((ushort)0x0020) /* PA 10 */
+#define PA_ENET_RCLK ((ushort)0x1000) /* PA 3 CLK 5 */
+#define PA_ENET_TCLK ((ushort)0x2000) /* PA 2 CLK 6 */
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
-#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
+#define PC_ENET_RENA ((ushort)0x0200) /* PC 6 */
+#define PC_ENET_CLSN ((ushort)0x0100) /* PC 7 */
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+/* Control bits in the SICR to route TCLK (CLK6) and RCLK (CLK5) to
* SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
*/
#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00260000)
-#endif /* CONFIG_SM850 */
-
-/*** SPD823TS ******************************************************/
-
-#ifdef CONFIG_SPD823TS
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
-#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_SPD823TS */
+#define SICR_ENET_CLKRT ((uint)0x00250000)
+#endif /* CONFIG_KM8XX */
-/*** SXNI855T ******************************************************/
-
-#if defined(CONFIG_SXNI855T)
-
-#ifdef CONFIG_FEC_ENET
-#define FEC_ENET /* use FEC for Ethernet */
-#endif /* CONFIG_FEC_ETHERNET */
-
-#endif /* CONFIG_SXNI855T */
-
-/*** MVS1, TQM823L, TQM850L, ETX094, R360MPI ***********************/
+/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
- defined(CONFIG_R360MPI) || \
defined(CONFIG_TQM823L) || \
- defined(CONFIG_TQM850L) || \
- defined(CONFIG_ETX094) || \
- defined(CONFIG_RRVISION)|| \
- (defined(CONFIG_LANTEC) && CONFIG_LANTEC < 2)
+ defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
+ defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D)
+
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC2 use.
*/
#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#if defined(CONFIG_R360MPI)
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#endif /* CONFIG_R360MPI */
/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
* SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
*/
#define SICR_ENET_MASK ((uint)0x0000ff00)
#define SICR_ENET_CLKRT ((uint)0x00002600)
-#endif /* CONFIG_MVS v1, CONFIG_TQM823L, CONFIG_TQM850L, etc. */
-/*** TQM860L, TQM855L ************************************************/
+# ifdef CONFIG_FEC_ENET /* Use FEC for Fast Ethernet */
+#define FEC_ENET
+# endif /* CONFIG_FEC_ENET */
-#if (defined(CONFIG_TQM860L) || defined(CONFIG_TQM855L))
+#endif /* CONFIG_MVS v1, CONFIG_TQM823L/M, CONFIG_TQM850L/M, etc. */
+
+/*** TQM855L/M, TQM860L/M, TQM862L/M, TQM866L/M *********************/
+
+#if defined(CONFIG_TQM855L) || defined(CONFIG_TQM855M) || \
+ defined(CONFIG_TQM860L) || defined(CONFIG_TQM860M) || \
+ defined(CONFIG_TQM862L) || defined(CONFIG_TQM862M) || \
+ defined(CONFIG_TQM866L) || defined(CONFIG_TQM866M)
# ifdef CONFIG_SCC1_ENET /* use SCC for 10Mbps Ethernet */
#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */
# endif /* CONFIG_FEC_ENET */
-#endif /* CONFIG_TQM860L, CONFIG_TQM855L */
-
-#if defined(CONFIG_NETVIA)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */
-
-#define PB_ENET_PDN ((ushort)0x4000) /* PB 17 */
-#define PB_ENET_TENA ((ushort)0x2000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002f00)
-
-#endif /* CONFIG_NETVIA */
+#endif /* CONFIG_TQM855L/M, TQM860L/M, TQM862L/M */
/*********************************************************************/
* priority and SCC1 == SCCa, etc...).
*/
#define CPMVEC_NR 32
-#define CPMVEC_PIO_PC15 ((ushort)0x1f)
-#define CPMVEC_SCC1 ((ushort)0x1e)
-#define CPMVEC_SCC2 ((ushort)0x1d)
-#define CPMVEC_SCC3 ((ushort)0x1c)
-#define CPMVEC_SCC4 ((ushort)0x1b)
-#define CPMVEC_PIO_PC14 ((ushort)0x1a)
-#define CPMVEC_TIMER1 ((ushort)0x19)
-#define CPMVEC_PIO_PC13 ((ushort)0x18)
-#define CPMVEC_PIO_PC12 ((ushort)0x17)
-#define CPMVEC_SDMA_CB_ERR ((ushort)0x16)
-#define CPMVEC_IDMA1 ((ushort)0x15)
-#define CPMVEC_IDMA2 ((ushort)0x14)
-#define CPMVEC_TIMER2 ((ushort)0x12)
-#define CPMVEC_RISCTIMER ((ushort)0x11)
-#define CPMVEC_I2C ((ushort)0x10)
-#define CPMVEC_PIO_PC11 ((ushort)0x0f)
-#define CPMVEC_PIO_PC10 ((ushort)0x0e)
-#define CPMVEC_TIMER3 ((ushort)0x0c)
-#define CPMVEC_PIO_PC9 ((ushort)0x0b)
-#define CPMVEC_PIO_PC8 ((ushort)0x0a)
-#define CPMVEC_PIO_PC7 ((ushort)0x09)
-#define CPMVEC_TIMER4 ((ushort)0x07)
-#define CPMVEC_PIO_PC6 ((ushort)0x06)
-#define CPMVEC_SPI ((ushort)0x05)
-#define CPMVEC_SMC1 ((ushort)0x04)
-#define CPMVEC_SMC2 ((ushort)0x03)
-#define CPMVEC_PIO_PC5 ((ushort)0x02)
-#define CPMVEC_PIO_PC4 ((ushort)0x01)
-#define CPMVEC_ERROR ((ushort)0x00)
+#define CPMVEC_OFFSET 0x00010000
+#define CPMVEC_PIO_PC15 ((ushort)0x1f | CPMVEC_OFFSET)
+#define CPMVEC_SCC1 ((ushort)0x1e | CPMVEC_OFFSET)
+#define CPMVEC_SCC2 ((ushort)0x1d | CPMVEC_OFFSET)
+#define CPMVEC_SCC3 ((ushort)0x1c | CPMVEC_OFFSET)
+#define CPMVEC_SCC4 ((ushort)0x1b | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC14 ((ushort)0x1a | CPMVEC_OFFSET)
+#define CPMVEC_TIMER1 ((ushort)0x19 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC13 ((ushort)0x18 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC12 ((ushort)0x17 | CPMVEC_OFFSET)
+#define CPMVEC_SDMA_CB_ERR ((ushort)0x16 | CPMVEC_OFFSET)
+#define CPMVEC_IDMA1 ((ushort)0x15 | CPMVEC_OFFSET)
+#define CPMVEC_IDMA2 ((ushort)0x14 | CPMVEC_OFFSET)
+#define CPMVEC_TIMER2 ((ushort)0x12 | CPMVEC_OFFSET)
+#define CPMVEC_RISCTIMER ((ushort)0x11 | CPMVEC_OFFSET)
+#define CPMVEC_I2C ((ushort)0x10 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC11 ((ushort)0x0f | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC10 ((ushort)0x0e | CPMVEC_OFFSET)
+#define CPMVEC_TIMER3 ((ushort)0x0c | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC9 ((ushort)0x0b | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC8 ((ushort)0x0a | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC7 ((ushort)0x09 | CPMVEC_OFFSET)
+#define CPMVEC_TIMER4 ((ushort)0x07 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC6 ((ushort)0x06 | CPMVEC_OFFSET)
+#define CPMVEC_SPI ((ushort)0x05 | CPMVEC_OFFSET)
+#define CPMVEC_SMC1 ((ushort)0x04 | CPMVEC_OFFSET)
+#define CPMVEC_SMC2 ((ushort)0x03 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC5 ((ushort)0x02 | CPMVEC_OFFSET)
+#define CPMVEC_PIO_PC4 ((ushort)0x01 | CPMVEC_OFFSET)
+#define CPMVEC_ERROR ((ushort)0x00 | CPMVEC_OFFSET)
extern void irq_install_handler(int vec, void (*handler)(void *), void *dev_id);
projects / people / ms / u-boot.git / blobdiff