cmd: add Kconfig option for 'date' command

[people/ms/u-boot.git] / include / configs / B4860QDS.h

diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
index e3ed3178a08046afcf3c04c4a0f3453ced329a6e..abfdbc927677997e419627ca08e88c460057cff9 100644 (file)
--- a/include/configs/B4860QDS.h
+++ b/include/configs/B4860QDS.h
@@ -35,7 +35,6 @@
 #define CONFIG_SPL_SKIP_RELOCATE
 #define CONFIG_SPL_COMMON_INIT_DDR
 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
-#define CONFIG_SYS_NO_FLASH
 #endif
 #endif
 #endif
@@ -46,7 +45,6 @@
 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_SYS_NO_FLASH
 #endif
 
 /* High Level Configuration Options */
@@ -62,9 +60,7 @@
 #endif
 
 #define CONFIG_SYS_FSL_CPC             /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC             CONFIG_NUM_DDR_CONTROLLERS
-#define CONFIG_FSL_IFC                 /* Enable IFC Support */
-#define CONFIG_FSL_CAAM                        /* Enable SEC/CAAM */
+#define CONFIG_SYS_NUM_CPC             CONFIG_SYS_NUM_DDR_CTLRS
 #define CONFIG_PCIE1                   /* PCIE controller 1 */
 #define CONFIG_FSL_PCI_INIT            /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT           /* enable 64-bit PCI resources */
@@ -110,7 +106,7 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#ifdef CONFIG_SYS_NO_FLASH
+#ifndef CONFIG_MTD_NOR_FLASH
 #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
 #define CONFIG_ENV_IS_NOWHERE
 #endif
@@ -222,13 +218,11 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_SYS_FSL_DDR3
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_FSL_DDR_INTERACTIVE
 #endif
@@ -677,7 +671,6 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_PCI_INDIRECT_BRIDGE
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 #ifdef CONFIG_FMAN_ENET
@@ -709,7 +702,6 @@ unsigned long get_board_ddr_clk(void);
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_DATE
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_IRQ
@@ -777,9 +769,6 @@ unsigned long get_board_ddr_clk(void);
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR                1000000
 
-
-#define CONFIG_BAUDRATE        115200
-
 #define __USB_PHY_TYPE ulpi
 
 #ifdef CONFIG_ARCH_B4860