Merge branch 'master' of git://git.denx.de/u-boot-spi

[people/ms/u-boot.git] / include / configs / BSC9132QDS.h

diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index 2722a329ddccc7dc5bfce4d580f335338b606214..9f7ceb838ed3ad93bc371cb571afe5de2512126b 100644 (file)
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -11,6 +11,8 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#define CONFIG_DISPLAY_BOARDINFO
+
 #ifdef CONFIG_BSC9132QDS
 #define CONFIG_BSC9132
 #endif
@@ -89,10 +91,8 @@
 #define CONFIG_FSL_PCIE_RESET          /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT           /* enable 64-bit PCI resources */
 
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
 
-#define CONFIG_E1000                   /*  E1000 pci Ethernet card*/
 
 /*
  * PCI Windows
@@ -317,7 +317,6 @@ combinations. this should be removed later
 /* NAND */
 #define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
@@ -409,7 +408,6 @@ combinations. this should be removed later
 /* Serial Port */
 #define CONFIG_CONS_INDEX      1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -417,7 +415,6 @@ combinations. this should be removed later
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif
 
-#define CONFIG_SERIAL_MULTI    1 /* Enable both serial ports */
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV   /* determine from environment */
 
 #define CONFIG_SYS_BAUDRATE_TABLE      \
@@ -434,17 +431,6 @@ combinations. this should be removed later
 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED       400800 /* I2C speed and slave address*/
@@ -465,7 +451,6 @@ combinations. this should be removed later
 
 /* enable read and write access to EEPROM */
 #define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -482,10 +467,7 @@ combinations. this should be removed later
  * used for SLIC
  */
 /* eSPI - Enhanced SPI */
-#define CONFIG_FSL_ESPI  /* SPI */
 #ifdef CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH_SPANSION
 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
@@ -580,17 +562,13 @@ combinations. this should be removed later
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
@@ -672,6 +650,7 @@ combinations. this should be removed later
 #define CONFIG_UBOOTPATH       "u-boot.bin"
 
 #define CONFIG_BAUDRATE                115200
+#define CONFIG_BOOTDELAY       10 /* -1 disable auto-boot */
 
 #ifdef CONFIG_SDCARD
 #define CONFIG_DEF_HWCONFIG    "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
@@ -732,8 +711,4 @@ combinations. this should be removed later
 
 #include <asm/fsl_secure_boot.h>
 
-#ifdef CONFIG_SECURE_BOOT
-#define CONFIG_CMD_BLOB
-#endif
-
 #endif /* __CONFIG_H */