* Note: my board is a PILOT rev.
* Note: the mpc8260ads doesn't come with a proper Ethernet MAC address.
*
+ * (C) Copyright 2003-2004 Arabella Software Ltd.
+ * Yuli Barcohen <yuli@arabellasw.com>
+ * Added support for SDRAM DIMMs SPD EEPROM, MII, JFFS2.
+ * Ported to PQ2FADS-ZU and PQ2FADS-VR boards.
+ * Ported to MPC8272ADS board.
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
* MA 02111-1307 USA
*/
-/*
- * Config header file for a MPC8260ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm
- */
-
#ifndef __CONFIG_H
#define __CONFIG_H
* (easy to change)
*/
-#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
-#define CONFIG_MPC8260ADS 1 /* ...on motorola ads board */
+#define CONFIG_MPC8260ADS 1 /* Motorola PQ2 ADS family board */
+
+/* ADS flavours */
+#define CFG_8260ADS 1 /* MPC8260ADS */
+#define CFG_8266ADS 2 /* MPC8266ADS */
+#define CFG_PQ2FADS 3 /* PQ2FADS-ZU or PQ2FADS-VR */
+#define CFG_8272ADS 4 /* MPC8272ADS */
+
+#ifndef CONFIG_ADSTYPE
+#define CONFIG_ADSTYPE CFG_8260ADS
+#endif /* CONFIG_ADSTYPE */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+#if CONFIG_ADSTYPE == CFG_8272ADS
+#define CONFIG_MPC8272 1
+#else
+#define CONFIG_MPC8260 1
+#endif /* CONFIG_ADSTYPE == CFG_8272ADS */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* allow serial and ethaddr to be overwritten */
#define CONFIG_ENV_OVERWRITE
#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */
#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
-#if (CONFIG_ETHER_INDEX == 2)
+#ifdef CONFIG_ETHER_ON_FCC
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Half duplex
- */
-# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */
+
+#if CONFIG_ETHER_INDEX == 1
+
+# define CFG_PHY_ADDR 0
+# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK10)
+# define CFG_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+
+#elif CONFIG_ETHER_INDEX == 2
+
+#if CONFIG_ADSTYPE == CFG_8272ADS /* RxCLK is CLK15, TxCLK is CLK16 */
+# define CFG_PHY_ADDR 3
+# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK15 | CMXFCR_TF2CS_CLK16)
+#else /* RxCLK is CLK13, TxCLK is CLK14 */
+# define CFG_PHY_ADDR 0
# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CFG_CPMFCR_RAMTYPE 0
-# define CFG_FCC_PSMR 0
+#endif /* CONFIG_ADSTYPE == CFG_8272ADS */
+
+# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
#endif /* CONFIG_ETHER_INDEX */
-/* other options */
+#define CFG_CPMFCR_RAMTYPE 0 /* BDs and buffers on 60x bus */
+#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) /* Full duplex */
+
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+/*
+ * GPIO pins used for bit-banged MII communications
+ */
+#define MDIO_PORT 2 /* Port C */
+
+#if CONFIG_ADSTYPE == CFG_8272ADS
+#define CFG_MDIO_PIN 0x00002000 /* PC18 */
+#define CFG_MDC_PIN 0x00001000 /* PC19 */
+#else
+#define CFG_MDIO_PIN 0x00400000 /* PC9 */
+#define CFG_MDC_PIN 0x00200000 /* PC10 */
+#endif /* CONFIG_ADSTYPE == CFG_8272ADS */
+
+#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN)
+#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN)
+#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0)
+
+#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \
+ else iop->pdat &= ~CFG_MDIO_PIN
+
+#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \
+ else iop->pdat &= ~CFG_MDC_PIN
+
+#define MIIDELAY udelay(1)
+
+#endif /* CONFIG_ETHER_ON_FCC */
+
+#if CONFIG_ADSTYPE >= CFG_PQ2FADS
+#undef CONFIG_SPD_EEPROM /* On new boards, SDRAM is soldered */
+#else
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#if defined(CONFIG_SPD_EEPROM) && !defined(CONFIG_SPD_ADDR)
#define CONFIG_SPD_ADDR 0x50
#endif
+#endif /* CONFIG_ADSTYPE >= CFG_PQ2FADS */
#ifndef CONFIG_SDRAM_PBI
-#define CONFIG_SDRAM_PBI 1 /* By default, use page-based interleaving */
+#define CONFIG_SDRAM_PBI 0 /* By default, use bank-based interleaving */
#endif
#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66666666 /* in Hz */
+#if CONFIG_ADSTYPE >= CFG_PQ2FADS
+#define CONFIG_8260_CLKIN 100000000 /* in Hz */
+#else
+#define CONFIG_8260_CLKIN 66000000 /* in Hz */
+#endif
#endif
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \
- CFG_CMD_BEDBUG | \
+#define CONFIG_BAUDRATE 38400
+
+#define CFG_EXCLUDE CFG_CMD_BEDBUG | \
+ CFG_CMD_BMP | \
CFG_CMD_BSP | \
CFG_CMD_DATE | \
CFG_CMD_DOC | \
CFG_CMD_DTT | \
CFG_CMD_EEPROM | \
CFG_CMD_ELF | \
+ CFG_CMD_FAT | \
CFG_CMD_FDC | \
CFG_CMD_FDOS | \
CFG_CMD_HWFLOW | \
CFG_CMD_IDE | \
- CFG_CMD_JFFS2 | \
CFG_CMD_KGDB | \
- CFG_CMD_MII | \
+ CFG_CMD_MMC | \
+ CFG_CMD_NAND | \
CFG_CMD_PCI | \
CFG_CMD_PCMCIA | \
+ CFG_CMD_REISER | \
CFG_CMD_SCSI | \
CFG_CMD_SPI | \
- CFG_CMD_VFD | \
- CFG_CMD_USB ) )
+ CFG_CMD_USB | \
+ CFG_CMD_VFD
+
+#if CONFIG_ADSTYPE >= CFG_PQ2FADS
+#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \
+ CFG_CMD_SDRAM | \
+ CFG_CMD_I2C | \
+ CFG_EXCLUDE ) )
+#else
+#define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \
+ CFG_EXCLUDE ) )
+#endif /* CONFIG_ADSTYPE >= CFG_PQ2FADS */
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */
-#define CONFIG_BOOTARGS "root=/dev/ram rw"
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_BOOTCOMMAND "bootm fff80000" /* autoboot command */
+#define CONFIG_BOOTARGS "root=/dev/mtdblock2"
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
#endif
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
+#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
+#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
/*
* Miscellaneous configurable options
*/
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
- /* for versions < 2.4.5-pre5 */
-
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#define CFG_FLASH_BASE 0xff800000
-#define FLASH_BASE 0xff800000
#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CFG_MAX_FLASH_SECT 32 /* max num of sects on one chip */
#define CFG_FLASH_SIZE 8
#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
+#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
+#define CFG_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
+
+#define CFG_JFFS2_FIRST_SECTOR 1
+#define CFG_JFFS2_LAST_SECTOR 27
+#define CFG_JFFS2_SORT_FRAGMENTS
+#define CFG_JFFS_CUSTOM_PART
/* this is stuff came out of the Motorola docs */
#define CFG_DEFAULT_IMMR 0x0F010000
-#define CFG_IMMR 0x04700000
-#define CFG_BCSR 0x04500000
+#define CFG_IMMR 0xF0000000
+#define CFG_BCSR 0xF4500000
#define CFG_SDRAM_BASE 0x00000000
-#define CFG_LSDRAM_BASE 0x04000000
+#define CFG_LSDRAM_BASE 0xFD000000
#define RS232EN_1 0x02000002
#define RS232EN_2 0x01000001
-#define FETHIEN 0x08000008
-#define FETH_RST 0x04000004
+#define FETHIEN1 0x08000008
+#define FETH1_RST 0x04000004
+#define FETHIEN2 0x10000000
+#define FETH2_RST 0x08000000
+#define BCSR_PCI_MODE 0x01000000
#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
( HRCW_BMS | HRCW_APPC10 ) |\
( HRCW_MODCK_H0101 ) \
)
-
/* no slaves */
#define CFG_HRCW_SLAVE1 0
#define CFG_HRCW_SLAVE2 0
#endif
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#ifdef CONFIG_BZIP2
+#define CFG_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
+#else
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 KB for malloc() */
+#endif /* CONFIG_BZIP2 */
+
#ifndef CFG_RAMBOOT
# define CFG_ENV_IS_IN_FLASH 1
-# define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-# define CFG_ENV_SECT_SIZE 0x40000
+# define CFG_ENV_SECT_SIZE 0x40000
+# define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_ENV_SECT_SIZE)
#else
# define CFG_ENV_IS_IN_NVRAM 1
# define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
#define CFG_SYPCR 0xFFFFFFC3
#define CFG_BCR 0x100C0000
#define CFG_SIUMCR 0x0A200000
-#define CFG_SCCR 0x00000000
-#define CFG_BR0_PRELIM 0xFF801801
-#define CFG_OR0_PRELIM 0xFF800836
-#define CFG_BR1_PRELIM 0x04501801
+#define CFG_SCCR SCCR_DFBRG01
+#define CFG_BR0_PRELIM CFG_FLASH_BASE | 0x00001801
+#define CFG_OR0_PRELIM 0xFF800876
+#define CFG_BR1_PRELIM CFG_BCSR | 0x00001801
#define CFG_OR1_PRELIM 0xFFFF8010
-#define CFG_RMR 0
+#define CFG_RMR RMR_CSRE
#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
#define CFG_RCCR 0
+
+#if (CONFIG_ADSTYPE == CFG_8266ADS) || (CONFIG_ADSTYPE == CFG_8272ADS)
+#undef CFG_LSDRAM_BASE /* No local bus SDRAM on these boards */
+#endif /* CONFIG_ADSTYPE == CFG_8266ADS */
+
+#if CONFIG_ADSTYPE == CFG_PQ2FADS
+#define CFG_OR2 0xFE002EC0
+#define CFG_PSDMR 0x824B36A3
+#define CFG_PSRT 0x13
+#define CFG_LSDMR 0x828737A3
+#define CFG_LSRT 0x13
+#define CFG_MPTPR 0x2800
+#elif CONFIG_ADSTYPE == CFG_8272ADS
+#define CFG_OR2 0xFC002CC0
+#define CFG_PSDMR 0x834E24A3
+#define CFG_PSRT 0x13
+#define CFG_MPTPR 0x2800
+#else
+#define CFG_OR2 0xFF000CA0
#define CFG_PSDMR 0x016EB452
-#define CFG_MPTPR 0x00001900
-#define CFG_PSRT 0x00000021
+#define CFG_PSRT 0x21
+#define CFG_LSDMR 0x0086A522
+#define CFG_LSRT 0x21
+#define CFG_MPTPR 0x1900
+#endif /* CONFIG_ADSTYPE == CFG_PQ2FADS */
#define CFG_RESET_ADDRESS 0x04400000
projects / people / ms / u-boot.git / blobdiff