Replace "run load; run update" with conditionalized "run load update".

[people/ms/u-boot.git] / include / configs / MPC8349EMDS.h

diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 0460be9e569cfaa6447ab3da1278c5ec01aecf08..07fefecf748310921e3a2b8e88aa7e31cf833407 100644 (file)
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -29,8 +29,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#undef DEBUG
-
 /*
  * High Level Configuration Options
  */
@@ -339,16 +337,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE    1
+#define CONFIG_OF_LIBFDT       1
 #define CONFIG_OF_BOARD_SETUP  1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE  8192
-
-#define OF_CPU                 "PowerPC,8349@0"
-#define OF_SOC                 "soc8349@e0000000"
-#define OF_TBCLK               (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH         "/soc8349@e0000000/serial@4500"
+#define CONFIG_OF_STDOUT_VIA_ALIAS     1
 
 /* I2C */
 #define CONFIG_HARD_I2C                        /* I2C with hardware support*/
@@ -362,6 +353,16 @@
 #define CFG_I2C_OFFSET         0x3000
 #define CFG_I2C2_OFFSET                0x3100
 
+/* SPI */
+#define CONFIG_MPC8XXX_SPI
+#define CONFIG_HARD_SPI                        /* SPI with hardware support */
+#undef CONFIG_SOFT_SPI                 /* SPI bit-banged */
+
+/* GPIOs.  Used as SPI chip selects */
+#define CFG_GPIO1_PRELIM
+#define CFG_GPIO1_DIR          0xC0000000  /* SPI CS on 0, LED on 1 */
+#define CFG_GPIO1_DAT          0xC0000000  /* Both are active LOW */
+
 /* TSEC */
 #define CFG_TSEC1_OFFSET 0x24000
 #define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
@@ -432,14 +433,16 @@
 #endif
 
 #define CONFIG_GMII            1       /* MII PHY management */
-#define CONFIG_MPC83XX_TSEC1   1
-#define CONFIG_MPC83XX_TSEC1_NAME      "TSEC0"
-#define CONFIG_MPC83XX_TSEC2   1
-#define CONFIG_MPC83XX_TSEC2_NAME      "TSEC1"
+#define CONFIG_TSEC1   1
+#define CONFIG_TSEC1_NAME      "TSEC0"
+#define CONFIG_TSEC2   1
+#define CONFIG_TSEC2_NAME      "TSEC1"
 #define TSEC1_PHY_ADDR         0
 #define TSEC2_PHY_ADDR         1
 #define TSEC1_PHYIDX           0
 #define TSEC2_PHYIDX           0
+#define TSEC1_FLAGS            TSEC_GIGABIT
+#define TSEC2_FLAGS            TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME                "TSEC0"
@@ -457,7 +460,7 @@
  */
 #ifndef CFG_RAMBOOT
        #define CFG_ENV_IS_IN_FLASH     1
-       #define CFG_ENV_ADDR            (CFG_MONITOR_BASE + 0x40000)
+       #define CFG_ENV_ADDR            (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
        #define CFG_ENV_SECT_SIZE       0x20000 /* 128K(one sector) for env */
        #define CFG_ENV_SIZE            0x2000
 
@@ -475,44 +478,35 @@
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE  1       /* allow baudrate change */
 
-#if defined(CFG_RAMBOOT)
-#if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS       ((CONFIG_CMD_DFL        \
-                                | CFG_CMD_PING         \
-                                | CFG_CMD_PCI          \
-                                | CFG_CMD_I2C          \
-                                | CFG_CMD_DATE)        \
-                               &                       \
-                                ~(CFG_CMD_ENV          \
-                                 | CFG_CMD_LOADS))
-#else
-#define  CONFIG_COMMANDS       ((CONFIG_CMD_DFL        \
-                                | CFG_CMD_PING         \
-                                | CFG_CMD_I2C          \
-                                | CFG_CMD_DATE)        \
-                               &                       \
-                                ~(CFG_CMD_ENV          \
-                                 | CFG_CMD_LOADS))
-#endif
-#else
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_MII
+
 #if defined(CONFIG_PCI)
-#define  CONFIG_COMMANDS       (CONFIG_CMD_DFL         \
-                               | CFG_CMD_PCI           \
-                               | CFG_CMD_PING          \
-                               | CFG_CMD_I2C           \
-                               | CFG_CMD_DATE          \
-                               )
-#else
-#define  CONFIG_COMMANDS       (CONFIG_CMD_DFL         \
-                               | CFG_CMD_PING          \
-                               | CFG_CMD_I2C           \
-                               | CFG_CMD_MII           \
-                               | CFG_CMD_DATE          \
-                               )
+    #define CONFIG_CMD_PCI
 #endif
+
+#if defined(CFG_RAMBOOT)
+    #undef CONFIG_CMD_ENV
+    #undef CONFIG_CMD_LOADS
 #endif
 
-#include <cmd_confdefs.h>
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
@@ -523,7 +517,7 @@
 #define CFG_LOAD_ADDR  0x2000000       /* default load address */
 #define CFG_PROMPT     "=> "           /* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
        #define CFG_CBSIZE      1024            /* Console I/O Buffer Size */
 #else
        #define CFG_CBSIZE      256             /* Console I/O Buffer Size */
@@ -541,13 +535,6 @@
  */
 #define CFG_BOOTMAPSZ  (8 << 20)       /* Initial Memory map for Linux*/
 
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE                32768
-#define CFG_CACHELINE_SIZE     32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT    5       /*log base 2 of the above value*/
-#endif
-
 #define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 
 #if 1 /*528/264*/
@@ -695,7 +682,7 @@
 #define BOOTFLAG_COLD  0x01    /* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM  0x02    /* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif
@@ -708,6 +695,7 @@
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_ETHADDR         00:04:9f:ef:23:33
 #define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETH1ADDR                00:E0:0C:00:7E:21
 #endif
 
@@ -729,7 +717,7 @@
 #define CONFIG_BAUDRATE         115200
 
 #define CONFIG_PREBOOT "echo;" \
-       "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+       "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
        "echo"
 
 #define        CONFIG_EXTRA_ENV_SETTINGS                                       \
@@ -751,7 +739,7 @@
        "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0"           \
        "update=protect off fe000000 fe03ffff; "                        \
                "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"     \
-       "upd=run load;run update\0"                                     \
+       "upd=run load update\0"                                         \
        "fdtaddr=400000\0"                                              \
        "fdtfile=mpc8349emds.dtb\0"                                     \
        ""