i2c, soft-i2c: switch to new multibus/multiadapter support

[people/ms/u-boot.git] / include / configs / MPC8568MDS.h

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 6237b23b7ecc2ce97ac49eb633c0ef7a01a181e6..05a69af6ae2f6e8de44edf52021802424ee79f24 100644 (file)
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -42,6 +42,7 @@
 #define CONFIG_PCI1            1       /* PCI controller */
 #define CONFIG_PCIE1           1       /* PCIE controller */
 #define CONFIG_FSL_PCI_INIT    1       /* use common fsl pci init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
@@ -71,14 +72,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xe0000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
@@ -261,7 +256,6 @@ extern unsigned long get_clock_freq(void);
 /* Use the HUSH parser*/
 #define CONFIG_SYS_HUSH_PARSER
 #ifdef  CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* pass open firmware flat tree */
@@ -274,7 +268,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C         /* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C                /* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C                 /* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x52
@@ -353,7 +346,6 @@ extern unsigned long get_clock_freq(void);
 
 #if defined(CONFIG_PCI)
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -364,10 +356,6 @@ extern unsigned long get_clock_freq(void);
 
 #endif /* CONFIG_PCI */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_MII             1       /* MII PHY management */
@@ -451,11 +439,11 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
@@ -481,8 +469,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_IPADDR    192.168.1.253
 
 #define CONFIG_HOSTNAME  unknown
-#define CONFIG_ROOTPATH  /nfsroot
-#define CONFIG_BOOTFILE  your.uImage
+#define CONFIG_ROOTPATH  "/nfsroot"
+#define CONFIG_BOOTFILE  "your.uImage"
 
 #define CONFIG_SERVERIP  192.168.1.1
 #define CONFIG_GATEWAYIP 192.168.1.1