-/*
- * Copyright 2004 Freescale Semiconductor.
+/*
+ * Copyright 2006 Freescale Semiconductor.
+ *
* Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
*
* See file CREDITS for list of people who contributed to this
*/
/*
- * mpc8641hpc3 board configuration file
- *
+ * MPC8641HPCN board configuration file
*
* Make sure you change the MAC address and other network params first,
* search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
-#undef DEBUG
+#undef DEBUG
-//#define RUN_DIAG 1
#ifdef RUN_DIAG
#define CFG_DIAG_ADDR 0xff800000
#endif
+
#define CFG_RESET_ADDRESS 0xfff00100
-//#define CONFIG_PCI
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */
+#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-/*#define CONFIG_DDR_ECC */ /* only for ECC DDR module */
-/*#define CONFIG_DDR_DLL */ /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#undef CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+/* #define CONFIG_DDR_INTERLEAVE 1 */
+#define CACHE_LINE_INTERLEAVING 0x20000000
+#define PAGE_INTERLEAVING 0x21000000
+#define BANK_INTERLEAVING 0x22000000
+#define SUPER_BANK_INTERLEAVING 0x23000000
+
+#define CONFIG_ALTIVEC 1
-#define CONFIG_ALTIVEC 1
-/*-----------------------------------------------------------------------
+/*
* L2CR setup -- make sure this is right for your board!
*/
-
-#define CFG_L2
+#define CFG_L2
#define L2_INIT 0
#define L2_ENABLE (L2CR_L2E)
#ifndef CONFIG_SYS_CLK_FREQ
-//#define CONFIG_SYS_CLK_FREQ 33000000
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-/* JB - XXX - Are these available on 86xx? */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
-
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
/*
* DDR Setup
*/
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
#define MPC86xx_DDR_SDRAM_CLK_CNTL
/*
* Determine DDR configuration from I2C interface.
*/
- #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */
#else
/*
- * Manually set up DDR parameters
+ * Manually set up DDR1 parameters
*/
-/* DDR I */
-#if 1
#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
#define CFG_DDR_CS0_BNDS 0x0000000F
#define CFG_DDR_INTERVAL 0x06090100
#define CFG_DDR_DATA_INIT 0xdeadbeef
#define CFG_DDR_CLK_CTRL 0x03800000
- #define CFG_DDR_OCD_CTRL 0x00000000
- #define CFG_DDR_OCD_STATUS 0x00000000
+ #define CFG_DDR_OCD_CTRL 0x00000000
+ #define CFG_DDR_OCD_STATUS 0x00000000
#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
- #define CFG_DDR_CONTROL2 0x04400000
+ #define CFG_DDR_CONTROL2 0x04400000
- //Not used in fixed_sdram function
+ /* Not used in fixed_sdram function */
#define CFG_DDR_MODE 0x00000022
#define CFG_DDR_CS1_BNDS 0x00000000
- #define CFG_DDR_CS2_BNDS 0x00000FFF //Not done
- #define CFG_DDR_CS3_BNDS 0x00000FFF //Not done
- #define CFG_DDR_CS4_BNDS 0x00000FFF //Not done
- #define CFG_DDR_CS5_BNDS 0x00000FFF //Not done
-
-
-
-#endif
+ #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
+ #define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
+ #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
+ #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
#endif
+#define CFG_ID_EEPROM 1
+#define ID_EEPROM_ADDR 0x57
/*
- * SDRAM on the Local Bus
- */
-//#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-//#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-/* In MPC8641HPCN, we allocate 16MB flash spaces at fe000000 and ff000000
- * We only have an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
+ * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
+ * There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
* map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
* However, when u-boot comes up, the flash_init needs hard start addresses
- * to build its info table. For user convenience, we have the flash addresses
- * as fe800000 and ff800000. That way, when we do flash operations, u-boot
- * knows where the flash is and the user can download u-boot code from promjet to
- * fef00000 <- more intuitive than fe700000. Note that, on switching the boot
- * location, fef00000 becomes fff00000.
-*/
+ * to build its info table. For user convenience, the flash addresses is
+ * fe800000 and ff800000. That way, u-boot knows where the flash is
+ * and the user can download u-boot code from promjet to fef00000, a
+ * more intuitive location than fe700000.
+ *
+ * Note that, on switching the boot location, fef00000 becomes fff00000.
+ */
#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
-#define CFG_FLASH_BASE2 0xff800000
+#define CFG_FLASH_BASE2 0xff800000
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
-
-/*Sri: This looks like a good place to init all the Local Bus chip selects*/
-
#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/
#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
-#define PIXIS_BASE 0xf8100000 /* PIXIS registers*/
-#define PIXIS_ID 0x0 /* MPC8641HPCN Board ID at offset 0*/
-#define PIXIS_VER 0x1 /* MPC8641HPCN board version version at offset 1*/
-#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2*/
-#define PIXIS_RST 0x4 /* PIXIS Reset Control register*/
-#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */
-#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
-#define PIXIS_VCTL 0x10 /* VELA Control Register */
-#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
-#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
-#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
-#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
-#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
-#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
-#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
+#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
+#define PIXIS_ID 0x0 /* Board ID at offset 0 */
+#define PIXIS_VER 0x1 /* Board version at offset 1 */
+#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
+#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
+#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */
+#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
+#define PIXIS_VCTL 0x10 /* VELA Control Register */
+#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
+#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
+#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
+#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
+#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-//#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-/*#define CFG_HPCN_FLASH_CFI_DRIVER */
+#define CFG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
-
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#undef CFG_RAMBOOT
#endif
-#if !defined(CFG_RAMBOOT)
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#if defined(CFG_RAMBOOT)
+#undef CONFIG_SPD_EEPROM
+#define CFG_SDRAM_SIZE 256
#endif
#undef CONFIG_CLOCKS_IN_MHZ
#define CONFIG_L1_INIT_RAM
-#undef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_LOCK 1
#ifndef CFG_INIT_RAM_LOCK
#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
#else
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
+/*
+ * Pass open firmware flat tree to kernel
+ */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
+#define OF_FLAT_TREE_MAX_SIZE 8192
-#define OF_CPU "PowerPC,8641@0"
-#define OF_SOC "soc8641@f8000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"
+#define OF_CPU "PowerPC,8641@0"
+#define OF_SOC "soc8641@f8000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"
-#define CFG_64BIT_VSPRINTF 1
-#define CFG_64BIT_STRTOUL 1
+#define CFG_64BIT_VSPRINTF 1
+#define CFG_64BIT_STRTOUL 1
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3100
-/* RapidIO MMU */
+/*
+ * RapidIO MMU
+ */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
* Addresses are mapped 1-1.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
-//#define CFG_PCI1_MEM_BASE 0xd0000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-//#define CFG_PCI1_IO_BASE 0xe0000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-//#define CFG_PCI1_IO_BUS 0x00000000
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
/* For RTL8139 */
+#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
#define _IO_BASE 0x00000000
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
-
-// #define CFG_PCI1_MEM_BASE 0x80000000
-// #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-// #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-// #define CFG_PCI1_IO_BASE 0xe2000000
-// #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-// #define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
-
-
+#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe3000000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-//#define CFG_SCSI_SCAN_BUS_REVERSE
-
+#undef CFG_SCSI_SCAN_BUS_REVERSE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_RTL8139
-
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
+/************************************************************
+ * USB support
+ ************************************************************/
+#define CONFIG_PCI_OHCI 1
+#define CONFIG_USB_OHCI_NEW 1
+#define CONFIG_USB_KEYBOARD 1
+#define CFG_DEVICE_DEREGISTER
+#define CFG_USB_EVENT_POLL 1
+#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET CFG_PCI2_IO_PHYS
+
+/*PCI video card used*/
+/*#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS*/
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CFG_ISA_IO_BASE_ADDRESS CFG_PCI2_IO_PHYS
+#endif
+
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-//#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#endif /* CONFIG_PCI */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID 4
+#define CFG_SCSI_MAX_LUN 1
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#endif
+
+#define CONFIG_MPC86XX_PCI2
+#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC86XX_TSEC1 1
-#define CONFIG_MPC86XX_TSEC1_NAME "eTSEC1"
-#define CONFIG_MPC86XX_TSEC2 1
-#define CONFIG_MPC86XX_TSEC2_NAME "eTSEC2"
-#define CONFIG_MPC86XX_TSEC3 1
-#define CONFIG_MPC86XX_TSEC3_NAME "eTSEC3"
-#define CONFIG_MPC86XX_TSEC4 1
-#define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4"
-
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "eTSEC4"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define CONFIG_ETHPRIME "eTSEC1"
#endif /* CONFIG_TSEC_ENET */
-
-/* BAT0 2G Cacheable, non-guarded
+/*
+ * BAT0 2G Cacheable, non-guarded
* 0x0000_0000 2G DDR
*/
-//#define CFG_DBAT0L (0x0 | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT0L (0x0 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE | BATL_MEMCOHERENCE)
-#define CFG_DBAT0U (0x0 | BATU_BL_512M | BATU_VS | BATU_VP)
-//#define CFG_IBAT0L CFG_DBAT0L
-//#define CFG_IBAT0L (0x0 | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT0L (0x0| BATL_PP_RW | BATL_CACHEINHIBIT | BATL_MEMCOHERENCE)
+#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
#define CFG_IBAT0U CFG_DBAT0U
-/* BAT1 1G Cache-inhibited, guarded
+/*
+ * BAT1 1G Cache-inhibited, guarded
* 0x8000_0000 512M PCI-Express 1 Memory
* 0xa000_0000 512M PCI-Express 2 Memory
- ** SS - Changed it for operating from 0xd0000000
+ * Changed it for operating from 0xd0000000
*/
-#define CFG_DBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT1U CFG_DBAT1U
-/* BAT2 512M Cache-inhibited, guarded
+/*
+ * BAT2 512M Cache-inhibited, guarded
* 0xc000_0000 512M RapidIO Memory
*/
-#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (CFG_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT2U CFG_DBAT2U
-/* BAT3 4M Cache-inhibited, guarded
+/*
+ * BAT3 4M Cache-inhibited, guarded
* 0xf800_0000 4M CCSR
*/
-#define CFG_DBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT3U CFG_DBAT3U
-/* BAT4 32M Cache-inhibited, guarded
+/*
+ * BAT4 32M Cache-inhibited, guarded
* 0xe200_0000 16M PCI-Express 1 I/O
* 0xe300_0000 16M PCI-Express 2 I/0
- ** SS - Note that this is at 0xe0000000
+ * Note that this is at 0xe0000000
*/
-#define CFG_DBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT4U CFG_DBAT4U
-/* BAT5 128K Cacheable, non-guarded
+/*
+ * BAT5 128K Cacheable, non-guarded
* 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
*/
#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_IBAT5L CFG_DBAT5L
#define CFG_IBAT5U CFG_DBAT5U
-/* BAT6 32M Cache-inhibited, guarded
+/*
+ * BAT6 32M Cache-inhibited, guarded
* 0xfe00_0000 32M FLASH
*/
-#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CFG_IBAT6U CFG_DBAT6U
-
#define CFG_DBAT7L 0x00000000
#define CFG_DBAT7U 0x00000000
#define CFG_IBAT7L 0x00000000
#define CFG_IBAT7U 0x00000000
-
-
-
/*
* Environment
*/
- #ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
- #else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
- #endif
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000)
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
#if defined(CFG_RAMBOOT)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_PCI \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_IMLS \
- | CFG_CMD_FLASH \
- | CFG_CMD_LOADS))
- #else
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_IMLS \
- | CFG_CMD_FLASH \
- | CFG_CMD_LOADS))
- #endif
-#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C)
- #else
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C)
- #endif
+ #undef CONFIG_CMD_ENV
+#endif
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+ #define CONFIG_CMD_SCSI
+ #define CONFIG_CMD_EXT2
#endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#if defined(CONFIG_CMD_KGDB)
+ #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#if defined(CONFIG_CMD_KGDB)
+ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-
/*
* Environment Configuration
*/
#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
-#define CONFIG_HAS_ETH1 1
-#define CONFIG_HAS_ETH2 1
-#define CONFIG_HAS_ETH3 1
+#define CONFIG_HAS_ETH1 1
+#define CONFIG_HAS_ETH2 1
+#define CONFIG_HAS_ETH3 1
-#define CONFIG_IPADDR 10.82.193.138
+#define CONFIG_IPADDR 192.168.1.100
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /opt/nfsroot
#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-#define CONFIG_SERVERIP 10.82.193.104
-#define CONFIG_GATEWAYIP 10.82.193.254
-#define CONFIG_NETMASK 255.255.252.0
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_LOADADDR 1000000 /* default location for tftp and bootm */
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
-//#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
- "ramdiskaddr=400000\0" \
+ "ramdiskaddr=2000000\0" \
"ramdiskfile=your.ramdisk.u-boot\0" \
- "pex0=echo ---------------------------; echo --------- PCI EXPRESS -----\0" \
- "pexstat=mw f8008000 84000004; echo -expect:- 16000000; md f8008004 1\0" \
- "pex1=pci write 1.0.0 4 146; pci write 1.0.0 10 80000000\0" \
- "pexd=echo -expect:- xxx01002 00100146; pci display 1.0.0 0 2\0" \
- "pex=run pexstat; run pex1; run pexd\0" \
+ "dtbaddr=c00000\0" \
+ "dtbfile=mpc8641_hpcn.dtb\0" \
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
"maxcpus=2"
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr - $dtbaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
projects / people / ms / u-boot.git / blobdiff