powerpc/85xx: Move RESET_VECTOR_ADDRESS into config.h

[people/ms/u-boot.git] / include / configs / P1_P2_RDB.h

diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h
index 2dfee3d1bd0793812f7b2b21328f85f8dfc8fa00..d18d2f6fb52c33acb5dbf74f83d105bd0184dc82 100644 (file)
--- a/include/configs/P1_P2_RDB.h
+++ b/include/configs/P1_P2_RDB.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -57,17 +57,23 @@
 #ifdef CONFIG_SDCARD
 #define CONFIG_RAMBOOT_SDCARD          1
 #define CONFIG_SYS_TEXT_BASE           0xf8f80000
+#define CONFIG_RESET_VECTOR_ADDRESS    0xf8fffffc
 #endif
 
 #ifdef CONFIG_SPIFLASH
 #define CONFIG_RAMBOOT_SPIFLASH                1
 #define CONFIG_SYS_TEXT_BASE           0xf8f80000
+#define CONFIG_RESET_VECTOR_ADDRESS    0xf8fffffc
 #endif
 
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE           0xeff80000
 #endif
 
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
+#endif
+
 #ifndef CONFIG_SYS_MONITOR_BASE
 #define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #endif
@@ -146,7 +152,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #undef CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_DLL
 
 #define CONFIG_MEM_INIT_VALUE  0xDeadBeef
 
@@ -359,6 +364,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 
 /* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME          "Slot 1"
 #define CONFIG_SYS_PCIE2_MEM_VIRT      0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_BUS       0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS      0xa0000000
@@ -369,6 +375,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_PCIE2_IO_SIZE       0x00010000      /* 64k */
 
 /* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME          "Slot 2"
 #define CONFIG_SYS_PCIE1_MEM_VIRT      0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_BUS       0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS      0xc0000000
@@ -541,6 +548,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ   (16 << 20)/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */