#ifndef __CONFIG_H
#define __CONFIG_H
+#ifdef CONFIG_MK_36BIT
+#define CONFIG_PHYS_64BIT
+#endif
+
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_P2020 1
#define CONFIG_P2020DS 1
#define CONFIG_MP 1 /* support multiple processors */
-#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash associated with the CDS board.
- * This allows booting from a promjet.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
#ifndef __ASSEMBLY__
extern unsigned long calculate_board_sys_clk(unsigned long dummy);
extern unsigned long calculate_board_ddr_clk(unsigned long dummy);
#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
/* DDR Setup */
-#define CONFIG_SYS_DDR_TLB_START 9
#define CONFIG_VERY_BIG_RAM
#define CONFIG_FSL_DDR3 1
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
+#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */
+
+#ifdef CONFIG_FSL_NGPIXIS
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
#ifdef CONFIG_PHYS_64BIT
#define PIXIS_BASE_PHYS 0xfffdf0000ull
#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */
-#define PIXIS_ID 0x0 /* Board ID at offset 0 */
-#define PIXIS_VER 0x1 /* Board version at offset 1 */
-#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
-#define PIXIS_CSR 0x3 /* PIXIS General control/status register */
-#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
-#define PIXIS_PWR 0x5 /* PIXIS Power status register */
-#define PIXIS_AUX 0x6 /* Auxiliary 1 register */
-#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
-#define PIXIS_AUX2 0x8 /* Auxiliary 2 register */
-#define PIXIS_VCTL 0x10 /* VELA Control Register */
-#define PIXIS_VSTAT 0x11 /* VELA Status Register */
-#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
-#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
-#define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */
-#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
-#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
-#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
-#define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */
-#define PIXIS_VSYSCLK0 0x19 /* VELA SYSCLK0 Register */
-#define PIXIS_VSYSCLK1 0x1A /* VELA SYSCLK1 Register */
-#define PIXIS_VSYSCLK2 0x1B /* VELA SYSCLK2 Register */
-#define PIXIS_VDDRCLK0 0x1C /* VELA DDRCLK0 Register */
-#define PIXIS_VDDRCLK1 0x1D /* VELA DDRCLK1 Register */
-#define PIXIS_VDDRCLK2 0x1E /* VELA DDRCLK2 Register */
-
-#define PIXIS_VWATCH 0x24 /* Watchdog Register */
-#define PIXIS_LED 0x25 /* LED Register */
-
-/* old pixis referenced names */
-#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
-#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0
-#define PIXIS_VSPEED2_TSEC1SER 0x8
-#define PIXIS_VSPEED2_TSEC2SER 0x4
-#define PIXIS_VSPEED2_TSEC3SER 0x2
-#define PIXIS_VSPEED2_TSEC4SER 0x1
-#define PIXIS_VCFGEN1_TSEC1SER 0x20
-#define PIXIS_VCFGEN1_TSEC2SER 0x20
-#define PIXIS_VCFGEN1_TSEC3SER 0x20
-#define PIXIS_VCFGEN1_TSEC4SER 0x20
-#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER \
- | PIXIS_VSPEED2_TSEC2SER \
- | PIXIS_VSPEED2_TSEC3SER \
- | PIXIS_VSPEED2_TSEC4SER)
-#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER \
- | PIXIS_VCFGEN1_TSEC2SER \
- | PIXIS_VCFGEN1_TSEC3SER \
- | PIXIS_VCFGEN1_TSEC4SER)
+#define PIXIS_LBMAP_SWITCH 7
+#define PIXIS_LBMAP_MASK 0xf0
+#define PIXIS_LBMAP_SHIFT 4
+#define PIXIS_LBMAP_ALTBANK 0x20
+#endif
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define CONFIG_SYS_64BIT_VSPRINTF 1
-#define CONFIG_SYS_64BIT_STRTOUL 1
-
-/* new uImage format support */
-#define CONFIG_FIT 1
-#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
-
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_NET
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
#endif
+/*
+ * USB
+ */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
projects / people / ms / u-boot.git / blobdiff