/*
- * (C) Copyright 2001
+ * (C) Copyright 2001-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
/*
* Imported from global configuration:
- * CONFIG_L2_CACHE
+ * CONFIG_MPC8255
+ * CONFIG_MPC8265
+ * CONFIG_200MHz
* CONFIG_266MHz
* CONFIG_300MHz
- * CONFIG_MPC8255
+ * CONFIG_L2_CACHE
+ * CONFIG_BUSMODE_60x
*/
/*
#define CONFIG_TQM8260 200 /* ...on a TQM8260 module Rev.200 */
#endif
-/* Define 60x busmode only if your TQM8260 has L2 cache! */
-#ifdef CONFIG_L2_CACHE
-# define CONFIG_BUSMODE_60x 1 /* bus mode: 60x */
-#else
-# undef CONFIG_BUSMODE_60x /* bus mode: 8260 */
-#endif
-
-/* The board with 300MHz CPU doesn't have L2 cache, but works in 60x bus mode */
-#ifdef CONFIG_300MHz
-# define CONFIG_BUSMODE_60x
-#endif
+#define CONFIG_CPM2 1 /* Has a CPM2 */
#define CONFIG_82xx_CONS_SMC1 1 /* console on SMC1 */
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+#define CONFIG_BOOTCOUNT_LIMIT
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE 230400
+#else
+#define CONFIG_BAUDRATE 9600
+#endif
+
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
+ "bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip;" \
- "bootm $(kernel_addr) $(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
"bootfile=/tftpboot/TQM8260/uImage\0" \
"kernel_addr=40040000\0" \
* for FCC)
*
* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
- * from CONFIG_COMMANDS to remove support for networking.
+ * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
*
* (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the
* X.29 connector, and FCC2 is hardwired to the X.1 connector)
/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#ifdef CONFIG_MPC8255
+#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265)
# define CONFIG_8260_CLKIN 66666666 /* in Hz */
-#else /* !CONFIG_MPC8255 */
+#else /* !CONFIG_MPC8255 && !CONFIG_MPC8265 */
# ifndef CONFIG_300MHz
# define CONFIG_8260_CLKIN 66666666 /* in Hz */
# else
# endif
#endif /* CONFIG_MPC8255 */
-#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
-#define CONFIG_BAUDRATE 230400
-#else
-#define CONFIG_BAUDRATE 9600
-#endif
-
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_I2C | \
- CFG_CMD_EEPROM)
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#if 0
/* Start port with environment in flash; switch to EEPROM later */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_FLASH_BASE+0x40000)
-#define CFG_ENV_SIZE 0x40000
-#define CFG_ENV_SECT_SIZE 0x40000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CFG_FLASH_BASE+0x40000)
+#define CONFIG_ENV_SIZE 0x40000
+#define CONFIG_ENV_SECT_SIZE 0x40000
#else
/* Final version: environment in EEPROM */
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0
-#define CFG_ENV_SIZE 2048
+#define CONFIG_ENV_IS_IN_EEPROM 1
+#define CONFIG_ENV_OFFSET 0
+#define CONFIG_ENV_SIZE 2048
#endif
/*-----------------------------------------------------------------------
*/
#define __HRCW__ALL__ (HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
-#ifdef CONFIG_MPC8255
+#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265)
# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
-#else /* ! MPC8255 */
+#else /* ! MPC8255 && !MPC8265 */
# if defined(CONFIG_266MHz)
# define CFG_HRCW_MASTER (__HRCW__ALL__ | HRCW_MODCK_H0111)
# elif defined(CONFIG_300MHz)
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif