rockchip: rk3368: add Sheep board

[people/ms/u-boot.git] / include / configs / TQM855M.h

diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index a893316efc8ec731d19babe3856ff89203bc9823..14b76a66bcfa91c7887f3f8cc1695fefb063480f 100644 (file)
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2000-2008
+ * (C) Copyright 2000-2014
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * SPDX-License-Identifier:    GPL-2.0+
@@ -25,11 +25,9 @@
 #define        CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
 #define CONFIG_SYS_SMC_RXBUFLEN        128
 #define CONFIG_SYS_MAXIDLE     10
-#define CONFIG_BAUDRATE                115200  /* console baudrate = 115kbps   */
 
 #define        CONFIG_BOOTCOUNT_LIMIT
 
-#define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds     */
 
 #define CONFIG_BOARD_TYPES     1       /* support board types          */
 
@@ -72,18 +70,13 @@
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled            */
 
-#define        CONFIG_STATUS_LED       1       /* Status LED enabled           */
-
 #undef CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
 
 /* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C                 /* I2C with hardware support    */
-#define        CONFIG_SOFT_I2C         1       /* I2C bit-banged               */
-
-#define CONFIG_SYS_I2C_SPEED           93000   /* 93 kHz is supposed to work   */
-#define CONFIG_SYS_I2C_SLAVE           0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT            /* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED      93000   /* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE      0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -99,7 +92,6 @@
 #define I2C_SCL(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
                        else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY      udelay(2)       /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50            /* EEPROM AT24C64       */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2               /* two byte address     */
@@ -118,41 +110,20 @@
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_BOOTFILESIZE
 
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
 #define        CONFIG_RTC_MPC8xx               /* use internal RTC of MPC8xx   */
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
 
 #define CONFIG_NETCONSOLE
 
-
 /*
  * Miscellaneous configurable options
  */
 #define        CONFIG_SYS_LONGHELP                     /* undef to save memory         */
-#define        CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt       */
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
-#define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser          */
 
 #if defined(CONFIG_CMD_KGDB)
 #define        CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
@@ -168,8 +139,6 @@
 
 #define        CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 
-#define        CONFIG_SYS_HZ                   1000    /* decrementer freq: 1 ms ticks */
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -490,9 +459,6 @@
 #define CONFIG_FEC_ENET
 #define CONFIG_ETHPRIME                "SCC"
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
 #define CONFIG_HWCONFIG                1
 
 #endif /* __CONFIG_H */