cmd: Kconfig: Add a Kconfig options for a few CMD

[people/ms/u-boot.git] / include / configs / UCP1020.h

diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index ad2f115c56645274ed6ee9498b3a814f45754d6c..ccdfafa0a16ce533542699b60a17f4a3bc2ea92d 100644 (file)
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -329,7 +329,6 @@
  */
 #define CONFIG_CONS_INDEX              1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -343,20 +342,6 @@
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR + 0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
@@ -380,13 +365,7 @@
  * eSPI - Enhanced SPI
  */
 #define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
 
-#define CONFIG_SPI_FLASH_SST           1
-#define CONFIG_SPI_FLASH_STMICRO       1
-#define CONFIG_SPI_FLASH_WINBOND       1
-#define CONFIG_CMD_SF                  1
-#define CONFIG_CMD_SPI                 1
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
 
@@ -489,18 +468,13 @@
  * Command line configuration.
  */
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_CRAMFS
-#define CONFIG_CRAMFS_CMDLINE
 
 /*
  * USB
@@ -513,7 +487,6 @@
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_USB_STORAGE
@@ -584,7 +557,6 @@
 #error "UCP1020 module revision is not defined !!!"
 #endif
 
-#define CONFIG_CMD_DHCP
 #define CONFIG_BOOTP_SERVERIP
 
 #define CONFIG_MII             /* MII PHY management */