cmd: Kconfig: Add a Kconfig options for a few CMD

[people/ms/u-boot.git] / include / configs / UCP1020.h

diff --git a/include/configs/UCP1020.h b/include/configs/UCP1020.h
index b9bbe340f34da894b7e42113c1117587b81e5f1d..ccdfafa0a16ce533542699b60a17f4a3bc2ea92d 100644 (file)
--- a/include/configs/UCP1020.h
+++ b/include/configs/UCP1020.h
@@ -14,7 +14,6 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO
 
 #define CONFIG_FSL_ELBC
@@ -47,7 +46,6 @@
 #define CONFIG_ETHPRIME                "eTSEC3"
 
 #ifndef CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH       y
 #endif
 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 
@@ -89,7 +87,6 @@
 #define CONFIG_ETHPRIME                "eTSEC1"
 
 #ifndef CONFIG_SPI_FLASH
-#define CONFIG_SPI_FLASH       y
 #endif
 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 
@@ -332,7 +329,6 @@
  */
 #define CONFIG_CONS_INDEX              1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -346,20 +342,6 @@
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR + 0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
@@ -383,13 +365,7 @@
  * eSPI - Enhanced SPI
  */
 #define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
 
-#define CONFIG_SPI_FLASH_SST           1
-#define CONFIG_SPI_FLASH_STMICRO       1
-#define CONFIG_SPI_FLASH_WINBOND       1
-#define CONFIG_CMD_SF                  1
-#define CONFIG_CMD_SPI                 1
 #define CONFIG_SF_DEFAULT_SPEED                10000000
 #define CONFIG_SF_DEFAULT_MODE         SPI_MODE_0
 
@@ -422,7 +398,6 @@
 #define CONFIG_SYS_PCIE1_IO_SIZE       0x00010000      /* 64k */
 
 #define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_E1000   /* Defind e1000 pci Ethernet card*/
 #define CONFIG_CMD_PCI
 
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
@@ -492,22 +467,14 @@
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
 #define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_ERRATA
 #define CONFIG_CMD_CRAMFS
-#define CONFIG_CRAMFS_CMDLINE
 
 /*
  * USB
@@ -520,7 +487,6 @@
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 
 #ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_USB_STORAGE
@@ -545,7 +511,6 @@
 #endif
 
 /* Misc Extra Settings */
-#define CONFIG_CMD_GPIO                        1
 #undef CONFIG_WATCHDOG /* watchdog disabled */
 
 /*
@@ -554,7 +519,6 @@
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
 #define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_SYS_PROMPT      "B$ "           /* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
 #else
@@ -593,7 +557,6 @@
 #error "UCP1020 module revision is not defined !!!"
 #endif
 
-#define CONFIG_CMD_DHCP
 #define CONFIG_BOOTP_SERVERIP
 
 #define CONFIG_MII             /* MII PHY management */