/*
- * U-boot - Configuration file for BF537 STAMP board
+ * U-Boot - Configuration file for BF537 STAMP board
*/
#ifndef __CONFIG_BF537_STAMP_H__
#include <asm/config-pre.h>
-
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf537-0.2
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
-
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 4
-
/*
* Memory Settings
*/
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
-
/*
* Network Settings
*/
#define CONFIG_NETCONSOLE 1
#endif
#define CONFIG_HOSTNAME bf537-stamp
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-
/*
* Flash Settings
/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
#define CONFIG_SYS_MAX_FLASH_SECT 71
-
/*
* SPI Settings
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 30000000
#define CONFIG_SF_DEFAULT_SPEED 30000000
-#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_ALL
-
/*
* Env Storage Settings
*/
* it linked after the configuration sector.
*/
# define LDS_BOARD_TEXT \
- arch/blackfin/lib/libblackfin.o (.text*); \
- arch/blackfin/cpu/libblackfin.o (.text*); \
+ arch/blackfin/lib/built-in.o (.text*); \
+ arch/blackfin/cpu/built-in.o (.text*); \
. = DEFINED(env_offset) ? env_offset : .; \
common/env_embedded.o (.text*);
#endif
-
/*
* I2C Settings
*/
-#define CONFIG_BFIN_TWI_I2C 1
-#define CONFIG_HARD_I2C 1
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_ADI
/*
* SPI_MMC Settings
*/
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
#define CONFIG_MMC_SPI
-
+#ifdef CONFIG_MMC_SPI
+#define CONFIG_GENERIC_MMC
+#endif
/*
* NAND Settings
*/
/* #define CONFIG_NAND_PLAT */
+#ifdef CONFIG_NAND_PLAT
#define CONFIG_SYS_NAND_BASE 0x20212000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)
#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)
#define NAND_PLAT_GPIO_DEV_READY GPIO_PF3
-
+#endif /* CONFIG_NAND_PLAT */
/*
* CF-CARD IDE-HDD Support
#if defined(CONFIG_BFIN_IDE)
-#define CONFIG_DOS_PARTITION 1
/*
* IDE/ATA stuff
*/
#endif
-
/*
* Misc Settings
*/
/* These are for board tests */
#if 0
#define CONFIG_BOOTCOMMAND "bootldr 0x203f0100"
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT \
- "autoboot in %d seconds: press space to stop\n", bootdelay
-#define CONFIG_AUTOBOOT_STOP_STR " "
#endif
-
/*
* Pull in common ADI header for remaining command/environment setup
*/