*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
*
- * SPDX-License-Identifier: GPL-2.0+
+ * SPDX-License-Identifier: GPL-2.0+
*/
/* ---
- * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
+ * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
* Date: 2004-03-29
* Author: Florian Schlote
*
#ifndef _CONFIG_COBRA5272_H
#define _CONFIG_COBRA5272_H
-/* ---
- * Define processor
- * possible values for Sentec board: only Coldfire M5272 processor supported
- * (please do not change)
- * ---
- */
-
-#define CONFIG_MCF52x2 /* define processor family */
-#define CONFIG_M5272 /* define processor type */
-
/* ---
* Defines processor clock - important for correct timings concerning serial
* interface etc.
- * CONFIG_SYS_HZ gives unit: 1000 -> 1 Hz ^= 1000 ms
* ---
*/
-#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_CLK 66000000
#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
-#define CONFIG_BAUDRATE 19200
/* ---
* set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_ENV_OFFSET 0x4000
#define CONFIG_ENV_SECT_SIZE 0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
#else
#define CONFIG_ENV_ADDR 0xffe04000
#define CONFIG_ENV_SECT_SIZE 0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
#endif
+#define LDS_BOARD_TEXT \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text);
/*
* BOOTP options
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
-
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_MII
#ifdef CONFIG_MCFFEC
# define CONFIG_MII 1
/*AUTOBOOT settings - booting images automatically by u-boot after power on*/
-#define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in
-seconds u-boot will wait before starting defined (auto-)boot command, setting
-to -1 disables delay, setting to 0 will too prevent access to u-boot command
-interface: u-boot then has to reflashed */
-
-
/* The following settings will be contained in the environment block ; if you
want to use a neutral environment all those settings can be manually set in
u-boot: 'set' command */
/* User network settings */
-#define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */
#define CONFIG_IPADDR 192.168.100.2 /* default board IP address */
#define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */
#endif
-#define CONFIG_SYS_PROMPT "COBRA > " /* Layout of u-boot prompt*/
-
#define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address
from which user programs will be started */