Convert CONFIG_CMD_IDE to Kconfig

[people/ms/u-boot.git] / include / configs / mecp5123.h

diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h
index a8b4b24470a4cdc52c31fb80d28bb705154f36a1..fcc1c682364333cc0cccf620350f013e229ecb17 100644 (file)
--- a/include/configs/mecp5123.h
+++ b/include/configs/mecp5123.h
@@ -15,8 +15,6 @@
 #define __CONFIG_H
 
 #define CONFIG_MECP5123 1
-#define CONFIG_DISPLAY_BOARDINFO
-#define CONFIG_SYS_GENERIC_BOARD
 
 /*
  * Memory map for the MECP5123 board:
@@ -37,7 +35,6 @@
 
 #define CONFIG_SYS_MPC512X_CLKIN       33333333        /* in Hz */
 
-#define CONFIG_BOARD_EARLY_INIT_F              /* call board_early_init_f() */
 #define CONFIG_MISC_INIT_R
 
 #define CONFIG_SYS_IMMR                        0x80000000
@@ -218,7 +215,6 @@
 #if CONFIG_PSC_CONSOLE != 3
 #error CONFIG_PSC_CONSOLE must be 3
 #endif
-#define CONFIG_BAUDRATE                9600    /* ... at 9600 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 
@@ -243,33 +239,13 @@
 #define SCCR2_CLOCKS_EN        (CLOCK_SCCR2_MEM_EN |   \
                         CLOCK_SCCR2_I2C_EN)
 
-
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* I2C */
-#define CONFIG_HARD_I2C                        /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE           0x7F    /* slave address */
 
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2       /* 16-bit EEPROM address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR     0x50    /* Atmel: AT24C32A-10TQ-2.7 */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10       /* 10ms of delay */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5    /* 32-Byte Page Write Mode */
-#define CONFIG_SYS_EEPROM_WREN                 /* Use EEPROM write protect */
-
 /*
  * Ethernet configuration
  */
@@ -289,28 +265,15 @@
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_EEPROM                /* Store env in I2C EEPROM      */
+#define CONFIG_ENV_IS_NOWHERE          /* Store env in I2C EEPROM      */
 #define CONFIG_ENV_SIZE                0x1000
 #define CONFIG_ENV_OFFSET       0x0000 /* environment starts here      */
 
 #define CONFIG_LOADS_ECHO              /* echo on for serial download  */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change        */
 
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DATE
-#undef CONFIG_CMD_FUSE
-#undef CONFIG_CMD_IDE
-#undef CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_ELF
-#define CONFIG_DOS_PARTITION
 
 /*
  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
@@ -376,7 +339,6 @@
 
 #define CONFIG_LOADADDR                400000  /* def. location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY       5       /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                        /* the boot command will set bootargs*/
 
 #define CONFIG_PREBOOT "echo;" \
@@ -429,9 +391,6 @@
 
 #define CONFIG_BOOTCOMMAND     "run flash_self"
 
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
 #define OF_CPU                 "PowerPC,5121@0"
 #define OF_SOC_COMPAT          "fsl,mpc5121-immr"
 #define OF_TBCLK               (bd->bi_busfreq / 4)