Convert CONFIG_ENV_IS_IN_FLASH to Kconfig

[people/ms/u-boot.git] / include / configs / p1_twr.h

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index 76189e136f2a2e8041bfddc2d29b0d354f16b992..d5f576946329cd87d906d61b7c31eb10f9a41ae7 100644 (file)
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -12,7 +12,6 @@
 
 #if defined(CONFIG_TWR_P1025)
 #define CONFIG_BOARDNAME "TWR-P1025"
-#define CONFIG_P1025
 #define CONFIG_PHY_ATHEROS
 #define CONFIG_QE
 #define CONFIG_SYS_LBC_LBCR    0x00080000      /* Conversion of LBC addr */
@@ -24,11 +23,11 @@
 #define CONFIG_SYS_RAMBOOT
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_SYS_TEXT_BASE           0x11000000
-#define CONFIG_RESET_VECTOR_ADDRESS    0x1107fffc
+#define CONFIG_RESET_VECTOR_ADDRESS    0x110bfffc
 #endif
 
 #ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE           0xeff80000
+#define CONFIG_SYS_TEXT_BASE           0xeff40000
 #endif
 
 #ifndef CONFIG_RESET_VECTOR_ADDRESS
@@ -39,27 +38,18 @@
 #define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #endif
 
-/* High Level Configuration Options */
-#define CONFIG_BOOKE
-#define CONFIG_E500
-#define CONFIG_MPC85xx
-
 #define CONFIG_MP
 
-#define CONFIG_FSL_ELBC
-#define CONFIG_PCI
-#define CONFIG_PCIE1   /* PCIE controler 1 (slot 1) */
-#define CONFIG_PCIE2   /* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE1   /* PCIE controller 1 (slot 1) */
+#define CONFIG_PCIE2   /* PCIE controller 2 (slot 2) */
 #define CONFIG_FSL_PCI_INIT    /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET  /* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT   /* enable 64-bit PCI resources */
 
-#define CONFIG_FSL_LAW
 #define CONFIG_TSEC_ENET       /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_CMD_SATA
 #define CONFIG_SATA_SIL3114
 #define CONFIG_SYS_SATA_MAX_DEVICE     2
 #define CONFIG_LIBATA
@@ -79,8 +69,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_L2_CACHE
 #define CONFIG_BTB
 
-#define CONFIG_BOARD_EARLY_INIT_F      /* Call board_pre_init */
-
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x1fffffff
 #define CONFIG_PANIC_HANG      /* do not reset board on panic */
@@ -89,7 +77,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
 
 #define CONFIG_SYS_SDRAM_SIZE_LAW      LAW_SIZE_512M
 #define CONFIG_CHIP_SELECTS_PER_CTRL   1
@@ -98,7 +85,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 
 /* Default settings for DDR3 */
@@ -203,7 +189,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
                                        GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)/* Reserve 512 kB for Mon */
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN  (1024 * 1024)/* Reserved for malloc */
 
 #define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
@@ -215,7 +201,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_CONS_INDEX              1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -226,26 +211,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
-
-/*
- * Pass open firmware flat tree
- */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-#define CONFIG_SYS_64BIT_VSPRINTF
-#define CONFIG_SYS_64BIT_STRTOUL
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
-
 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL                     /* Use FSL common I2C driver */
@@ -264,8 +229,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_I2C_PCA9555_ADDR    0x23
 
 /* enable read and write access to EEPROM */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
@@ -274,7 +237,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * eSPI - Enhanced SPI
  */
 #define CONFIG_HARD_SPI
-#define CONFIG_FSL_ESPI
 
 #if defined(CONFIG_PCI)
 /*
@@ -304,22 +266,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_PCIE1_IO_PHYS       0xffc00000
 #define CONFIG_SYS_PCIE1_IO_SIZE       0x00010000      /* 64k */
 
-#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_E1000   /* Defind e1000 pci Ethernet card*/
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
 
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI
-#endif
-
 #define CONFIG_MII             /* MII PHY management */
 #define CONFIG_TSEC1
 #define CONFIG_TSEC1_NAME      "eTSEC1"
@@ -352,7 +305,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #ifdef CONFIG_QE
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR     0xefec0000
+#define CONFIG_SYS_QE_FW_ADDR  0xefec0000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x10000
 #endif /* CONFIG_QE */
 
@@ -392,26 +345,30 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif /* CONFIG_UEC_ETH5 */
 #endif /* CONFIG_TWR-P1025 */
 
+/*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=ec000000.nor"
+#define MTDPARTS_DEFAULT "mtdparts=ec000000.nor:256k(vsc7385-firmware)," \
+                       "256k(dtb),5632k(kernel),57856k(fs)," \
+                       "256k(qe-ucode-firmware),1280k(u-boot)"
+
 /*
  * Environment
  */
 #ifdef CONFIG_SYS_RAMBOOT
 #ifdef CONFIG_RAMBOOT_SDCARD
-#define CONFIG_ENV_IS_IN_MMC
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_SYS_MMC_ENV_DEV 0
 #else
-#define CONFIG_ENV_IS_NOWHERE  /* Store ENV in memory only */
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE                0x2000
 #endif
 #else
-#define CONFIG_ENV_IS_IN_FLASH
-#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
-#define CONFIG_ENV_ADDR        0xfff80000
-#else
 #define CONFIG_ENV_ADDR        (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#endif
 #define CONFIG_ENV_SIZE                0x2000
 #define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
 #endif
@@ -422,14 +379,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO
 
 /*
@@ -438,30 +387,15 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_HAS_FSL_DR_USB
 
 #if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_STORAGE
 #endif
 #endif
 
-#define CONFIG_MMC
-
 #ifdef CONFIG_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR      CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#endif
-
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
-                || defined(CONFIG_FSL_SATA)
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
 #endif
 
 #undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -501,11 +435,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR        1000000
 
-#define CONFIG_BOOTDELAY 10    /* -1 disables auto-boot */
 #define CONFIG_BOOTARGS        /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS       \
 "netdev=eth0\0"        \
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"    \
@@ -547,7 +478,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 "consoledev=ttyS0\0"   \
 "ramdiskaddr=2000000\0"        \
 "ramdiskfile=rootfs.ext2.gz.uboot\0"   \
-"fdtaddr=c00000\0"     \
+"fdtaddr=1e00000\0"    \
 "bdev=sda1\0"  \
 "norbootaddr=ef080000\0"       \
 "norfdtaddr=ef040000\0"        \