* High Level Configuration Options
*/
#define CONFIG_E300 1 /* E300 Family */
-#define CONFIG_MPC83xx 1 /* MPC83xx family */
#define CONFIG_MPC834x 1 /* MPC834x family */
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_VME8349 1 /* ESD VME8349 board specific */
#define CONFIG_MISC_INIT_R
-#define CONFIG_PCI
/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_CMDLINE_EDITING /* add command line history */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
/* I2C */
#define CONFIG_SYS_I2C
#ifndef VME_CADDY2
#endif
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
* TSEC configuration
*/
#ifdef VME_CADDY2
-#define CONFIG_E1000
#else
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
#endif
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#else
- #define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DATE
#define CONFIG_SYS_RTC_BUS_NUM 0x01
#define CONFIG_SYS_I2C_RTC_ADDR 0x32
#define CONFIG_RTC_RX8025
#define CONFIG_CMD_PCI
#endif
-#if defined(CONFIG_SYS_RAMBOOT)
- #undef CONFIG_CMD_ENV
- #undef CONFIG_CMD_LOADS
-#endif
-
-#define CONFIG_CMD_ELF
/* Pass Ethernet MAC to VxWorks */
#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */
-#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
#undef CONFIG_BOOTARGS /* boot command will set bootargs */
-#define CONFIG_BAUDRATE 9600
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=vme8349\0" \