Kconfig: Drop CONFIG_CMD_DS4510

[people/ms/u-boot.git] / include / configs / xpedite537x.h

diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
index 8d595c9e55b4f9fbc9360d59265267061ada80f1..a12a3f8347cb406fb495a1e1e0fe1e6e00219064 100644 (file)
--- a/include/configs/xpedite537x.h
+++ b/include/configs/xpedite537x.h
@@ -14,10 +14,6 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_BOOKE           1       /* BOOKE */
-#define CONFIG_E500            1       /* BOOKE e500 family */
-#define CONFIG_MPC8572         1
-#define CONFIG_XPEDITE5370     1
 #define CONFIG_SYS_BOARD_NAME  "XPedite5370"
 #define CONFIG_SYS_FORM_3U_VPX 1
 #define CONFIG_BOARD_EARLY_INIT_R      /* Call board_pre_init */
@@ -26,8 +22,6 @@
 #define CONFIG_SYS_TEXT_BASE   0xfff80000
 #endif
 
-#define CONFIG_PCI             1       /* Enable PCI/PCIE */
-#define CONFIG_PCI_PNP         1       /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW   1       /* show pci devices on startup */
 #define CONFIG_PCIE1           1       /* PCIE controller 1 */
 #define CONFIG_PCIE2           1       /* PCIE controller 2 */
@@ -35,8 +29,6 @@
 #define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
-#define CONFIG_FSL_ELBC                1
 
 /*
  * Multicore config
@@ -48,7 +40,6 @@
 /*
  * DDR config
  */
-#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -56,7 +47,6 @@
 #define SPD_EEPROM_ADDRESS1            0x54    /* Both channels use the */
 #define SPD_EEPROM_ADDRESS2            0x54    /* same SPD data         */
 #define SPD_EEPROM_OFFSET              0x200   /* OFFSET of SPD in EEPROM */
-#define CONFIG_NUM_DDR_CONTROLLERS     2
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   1
 #define CONFIG_DDR_ECC
@@ -219,7 +209,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 #define CONFIG_SYS_BAUDRATE_TABLE      \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_BAUDRATE                        115200
 #define CONFIG_LOADS_ECHO              1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
@@ -365,9 +354,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /*
  * Command configuration.
  */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DS4510
-#define CONFIG_CMD_DS4510_INFO
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_JFFS2