/*
* Qualcomm Atheros OUI and vendor specific assignments
- * Copyright (c) 2014-2015, Qualcomm Atheros, Inc.
+ * Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
+ * Copyright (c) 2018, The Linux Foundation
*
* This software may be distributed under the terms of the BSD license.
* See README for more details.
* which supports DFS offloading, to indicate a radar pattern has been
* detected. The channel is now unusable.
*
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap
+ * based on enum wifi_logger_supported_features. Attributes defined in
+ * enum qca_wlan_vendor_attr_get_logger_features.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular
+ * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the
+ * attribute for this command. Attributes defined in
+ * enum qca_wlan_vendor_attr_wifi_logger_start.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS
+ * capabilities of the driver, parameters includes the attributes defined
+ * in enum qca_wlan_vendor_attr_tdls_get_capabilities.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload
+ * sending of certain periodic IP packet to firmware, attributes defined in
+ * enum qca_wlan_vendor_attr_offloaded_packets.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI
+ * monitoring, defines min and max RSSI which are configured for RSSI
+ * monitoring. Also used to notify the RSSI breach and provides the BSSID
+ * and RSSI value that was breached. Attributes defined in
+ * enum qca_wlan_vendor_attr_rssi_monitoring.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN
+ * Data Path (NDP) related operations, attributes defined in
+ * enum qca_wlan_vendor_attr_ndp_params.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable
+ * Neighbour Discovery offload, attributes defined in
+ * enum qca_wlan_vendor_attr_nd_offload.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various
+ * configuration parameter for BPF packet filter, attributes defined in
+ * enum qca_wlan_vendor_attr_packet_filter.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware
+ * maximum supported size, attributes defined in
+ * enum qca_wlan_vendor_drv_info.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various
+ * data about wake reasons and datapath IP statistics, attributes defined
+ * in enum qca_wlan_vendor_attr_wake_stats.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration
+ * for IEEE 802.11 communicating outside the context of a basic service
+ * set, called OCB command. Uses the attributes defines in
+ * enum qca_wlan_vendor_attr_ocb_set_config.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB
+ * UTC time. Use the attributes defines in
+ * enum qca_wlan_vendor_attr_ocb_set_utc_time.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start
+ * sending OCB timing advert frames. Uses the attributes defines in
+ * enum qca_wlan_vendor_attr_ocb_start_timing_advert.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop
+ * OCB timing advert. Uses the attributes defines in
+ * enum qca_wlan_vendor_attr_ocb_stop_timing_advert.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF
+ * timer value. Uses the attributes defines in
+ * enum qca_wlan_vendor_attr_ocb_get_tsf_resp.
+ *
* @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
* start the P2P Listen offload function in device and pass the listen
* channel, period, interval, count, device types, and vendor specific
*
* @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
* attributes defined in enum qca_wlan_gpio_attr.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
+ * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
+ * capabilities are to be fetched and other
+ * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
+ * requested capabilities.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
+ * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
+ * command and event.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for
+ * indoor location features. Capabilities are reported in
+ * QCA_WLAN_VENDOR_ATTR_LOC_CAPA.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM
+ * (fine timing measurement) session with one or more peers.
+ * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and
+ * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS.
+ * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT
+ * events will be reported, followed by
+ * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate
+ * end of session.
+ * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session.
+ * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with
+ * status code indicating session was aborted.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement
+ * results for one peer. Results are reported in
+ * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when
+ * FTM session is finished, either successfully or aborted by
+ * request.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder
+ * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether
+ * to enable or disable the responder. LCI/LCR reports can be
+ * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and
+ * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple
+ * times to update the LCI/LCR reports.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of
+ * arrival) measurement with a single peer. Specify peer MAC address in
+ * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in
+ * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel
+ * scan results cache and use the frequency from there).
+ * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE.
+ * Measurement result is reported in
+ * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify
+ * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports
+ * the AOA measurement result.
+ * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR.
+ * success/failure status is reported in
+ * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS.
+ * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
+ * The antenna array(s) used in the measurement are reported in
+ * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given
+ * data as per the given parameters.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a
+ * specific chain.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level
+ * configuration for a DMG RF sector. Specify sector index in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules
+ * to return sector information for in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration
+ * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the
+ * exact time where information was captured in
+ * QCA_WLAN_VENDOR_ATTR_TSF.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level
+ * configuration for a DMG RF sector. Specify sector index in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration
+ * for one or more DMG RF modules in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected
+ * DMG RF sector for a station. This is the sector that the HW
+ * will use to communicate with the station. Specify the MAC address
+ * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not
+ * needed for unassociated station). Specify sector type to return in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected
+ * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
+ * Also return the exact time where the information was captured
+ * in QCA_WLAN_VENDOR_ATTR_TSF.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the
+ * selected DMG RF sector for a station. This is the sector that
+ * the HW will use to communicate with the station.
+ * Specify the MAC address of associated station/AP/PCP in
+ * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in
+ * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index
+ * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX.
+ * The selected sector will be locked such that it will not be
+ * modified like it normally does (for example when station
+ * moves around). To unlock the selected sector for a station
+ * pass the special value 0xFFFF in the sector index. To unlock
+ * all connected stations also pass a broadcast MAC address.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior
+ * in the host driver. The different TDLS configurations are defined
+ * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE
+ * capabilities. The response uses the attributes defined in
+ * enum qca_wlan_vendor_attr_get_he_capabilities.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was
+ * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
+ * carries the scan cookie of the corresponding scan request. The scan
+ * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
+ * Absorption Rate (SAR) power limits. A critical regulation for
+ * FCC compliance, OEMs require methods to set SAR limits on TX
+ * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
+ * attributes are used with this command.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the
+ * host driver for offloading the implementation of Auto Channel Selection
+ * (ACS) to an external user space entity. This interface is used as the
+ * event from the host driver to the user space entity and also as the
+ * request from the user space entity to the host driver. The event from
+ * the host driver is used by the user space entity as an indication to
+ * start the ACS functionality. The attributes used by this event are
+ * represented by the enum qca_wlan_vendor_attr_external_acs_event.
+ * User space entity uses the same interface to inform the host driver with
+ * selected channels after the ACS operation using the attributes defined
+ * by enum qca_wlan_vendor_attr_external_acs_channels.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the
+ * requisite information leading to a power save failure. The information
+ * carried as part of this event is represented by the
+ * enum qca_attr_chip_power_save_failure attributes.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics
+ * collection. Uses attributes defined in enum qca_attr_nud_stats_set.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These
+ * statistics are represented by the enum qca_attr_nud_stats_get
+ * attributes.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch
+ * the BSS transition status, whether accept or reject, for a list of
+ * candidate BSSIDs provided by the userspace. This uses the vendor
+ * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and
+ * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify
+ * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an
+ * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in
+ * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response
+ * the driver shall specify array of
+ * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and
+ * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in
+ * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a
+ * specific QCA module. The trace levels are represented by
+ * enum qca_attr_trace_level attributes.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement
+ * Protocol antenna limit in different modes. See enum
+ * qca_wlan_vendor_attr_brp_ant_limit_mode.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan
+ * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan.
+ * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE)
+ * identifying the operation in success case.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses
+ * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to
+ * be stopped.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the
+ * specific interface. This can be used to modify some of the low level
+ * scan parameters (off channel dwell time, home channel time) in the
+ * driver/firmware. These parameters are maintained within the host driver.
+ * This command is valid only when the interface is in the connected state.
+ * These scan parameters shall be reset by the driver/firmware once
+ * disconnected. The attributes used with this command are defined in
+ * enum qca_wlan_vendor_attr_active_tos.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the
+ * driver has detected an internal failure. This event carries the
+ * information indicating the reason that triggered this detection. The
+ * attributes for this command are defined in
+ * enum qca_wlan_vendor_attr_hang.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values
+ * of spectral parameters used. The spectral scan parameters are specified
+ * by enum qca_wlan_vendor_attr_spectral_scan.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats
+ * for spectral scan functionality. The debug stats are specified by
+ * enum qca_wlan_vendor_attr_spectral_diag_stats.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral
+ * scan system capabilities. The capabilities are specified
+ * by enum qca_wlan_vendor_attr_spectral_cap.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current
+ * status of spectral scan. The status values are specified
+ * by enum qca_wlan_vendor_attr_spectral_scan_status.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush
+ * peer pending packets. Specify the peer MAC address in
+ * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets
+ * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed
+ * in enum qca_wlan_vendor_attr_flush_pending.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative
+ * RF Operating Parameter (RROP) information. The attributes for this
+ * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is
+ * intended for use by external Auto Channel Selection applications.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate
+ * (SAR) power limits. This is a companion to the command
+ * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the
+ * settings currently in use. The attributes returned by this command are
+ * defined by enum qca_vendor_attr_sar_limits.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of
+ * the WLAN hardware MAC. Also, provides the WLAN netdev interface
+ * information attached to the respective MAC.
+ * This works both as a query (user space asks the current mode) or event
+ * interface (driver advertising the current mode to the user space).
+ * Driver does not trigger this event for temporary hardware mode changes.
+ * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion,
+ * channel change, etc.) are updated with this event. Attributes for this
+ * interface are defined in enum qca_wlan_vendor_attr_mac.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold
+ * per peer per TID. Attributes for this command are define in
+ * enum qca_wlan_set_qdepth_thresh_attr.
+ * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action
+ * guide for WLAN driver. Request to suspend of driver and FW if the
+ * temperature is higher than the suspend threshold; resume action is
+ * requested to driver if the temperature is lower than the resume
+ * threshold. In user poll mode, request temperature data by user. For test
+ * purpose, getting thermal shutdown configuration parameters is needed.
+ * Attributes for this interface are defined in
+ * enum qca_wlan_vendor_attr_thermal_cmd.
+ * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from
+ * driver. Thermal temperature and indication of resume completion are
+ * reported as thermal events. The attributes for this command are defined
+ * in enum qca_wlan_vendor_attr_thermal_event.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10,
QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11,
QCA_NL80211_VENDOR_SUBCMD_NAN = 12,
- QCA_NL80211_VENDOR_SUBMCD_STATS_EXT = 13,
+ QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15,
QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60,
- /* 61-73 - reserved for QCA */
+ QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61,
+ QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62,
+ QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63,
+ QCA_NL80211_VENDOR_SUBCMD_ROAM = 64,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73,
/* Wi-Fi configuration subcommands */
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74,
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75,
- /* 76-90 - reserved for QCA */
+ QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76,
+ QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77,
+ QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78,
+ QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79,
+ QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80,
+ QCA_NL80211_VENDOR_SUBCMD_NDP = 81,
+ QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82,
+ QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83,
+ QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84,
+ QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85,
+ /* 86-90 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91,
QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92,
QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93,
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125,
+ QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127,
+ /* FTM/indoor location subcommands */
+ QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128,
+ QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129,
+ QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130,
+ QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131,
+ QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132,
+ QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133,
+ QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134,
+ QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135,
+ QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136,
+ QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137,
+ QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138,
+ /* DMG low level RF sector operations */
+ QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139,
+ QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140,
+ QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141,
+ QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142,
+ QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143,
+ QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144,
+ QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145,
+ QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146,
+ QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147,
+ QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148,
+ QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149,
+ QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150,
+ QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151,
+ QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152,
+ QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153,
+ QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154,
+ QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155,
+ QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156,
+ QCA_NL80211_VENDOR_SUBCMD_HANG = 157,
+ QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158,
+ QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159,
+ QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160,
+ QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161,
+ /* Flush peer pending data */
+ QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162,
+ QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163,
+ QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164,
+ QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165,
+ QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166,
+ /* Thermal shutdown commands to protect wifi chip */
+ QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167,
+ QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168,
};
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11,
/* Unsigned 32-bit value from enum qca_set_band. */
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12,
+ /* Dummy (NOP) attribute for 64 bit padding */
+ QCA_WLAN_VENDOR_ATTR_PAD = 13,
+ /* Unique FTM session cookie (Unsigned 64 bit). Specified in
+ * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in
+ * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and
+ * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE.
+ */
+ QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14,
+ /* Indoor location capabilities, returned by
+ * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA.
+ * see enum qca_wlan_vendor_attr_loc_capa.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15,
+ /* Array of nested attributes containing information about each peer
+ * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info
+ * for supported attributes for each peer.
+ */
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16,
+ /* Array of nested attributes containing measurement results for
+ * one or more peers, reported by the
+ * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event.
+ * See enum qca_wlan_vendor_attr_peer_result for list of supported
+ * attributes.
+ */
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17,
+ /* Flag attribute for enabling or disabling responder functionality. */
+ QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18,
+ /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
+ * command to specify the LCI report that will be sent by
+ * the responder during a measurement exchange. The format is
+ * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10.
+ */
+ QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19,
+ /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
+ * command to specify the location civic report that will
+ * be sent by the responder during a measurement exchange.
+ * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13.
+ */
+ QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20,
+ /* Session/measurement completion status code,
+ * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and
+ * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT
+ * see enum qca_vendor_attr_loc_session_status.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21,
+ /* Initial dialog token used by responder (0 if not specified),
+ * unsigned 8 bit value.
+ */
+ QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22,
+ /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS
+ * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if
+ * AOA measurements are needed as part of an FTM session.
+ * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See
+ * enum qca_wlan_vendor_attr_aoa_type.
+ */
+ QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23,
+ /* A bit mask (unsigned 32 bit value) of antenna arrays used
+ * by indoor location measurements. Refers to the antenna
+ * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24,
+ /* AOA measurement data. Its contents depends on the AOA measurement
+ * type and antenna array mask:
+ * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values,
+ * phase of the strongest CIR path for each antenna in the measured
+ * array(s).
+ * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16
+ * values, phase and amplitude of the strongest CIR path for each
+ * antenna in the measured array(s).
+ */
+ QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25,
+ /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
+ * to specify the chain number (unsigned 32 bit value) to inquire
+ * the corresponding antenna RSSI value */
+ QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26,
+ /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
+ * to report the specific antenna RSSI value (unsigned 32 bit value) */
+ QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27,
+ /* Frequency in MHz, various uses. Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_FREQ = 28,
+ /* TSF timer value, unsigned 64 bit value.
+ * May be returned by various commands.
+ */
+ QCA_WLAN_VENDOR_ATTR_TSF = 29,
+ /* DMG RF sector index, unsigned 16 bit number. Valid values are
+ * 0..127 for sector indices or 65535 as special value used to
+ * unlock sector selection in
+ * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR.
+ */
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30,
+ /* DMG RF sector type, unsigned 8 bit value. One of the values
+ * in enum qca_wlan_vendor_attr_dmg_rf_sector_type.
+ */
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31,
+ /* Bitmask of DMG RF modules for which information is requested. Each
+ * bit corresponds to an RF module with the same index as the bit
+ * number. Unsigned 32 bit number but only low 8 bits can be set since
+ * all DMG chips currently have up to 8 RF modules.
+ */
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32,
+ /* Array of nested attributes where each entry is DMG RF sector
+ * configuration for a single RF module.
+ * Attributes for each entry are taken from enum
+ * qca_wlan_vendor_attr_dmg_rf_sector_cfg.
+ * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG
+ * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG.
+ */
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33,
+ /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command
+ * to report frame aggregation statistics to userspace.
+ */
+ QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34,
+ QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35,
+ /* Unsigned 8-bit value representing MBO transition reason code as
+ * provided by the AP used by subcommand
+ * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is
+ * specified by the userspace in the request to the driver.
+ */
+ QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36,
+ /* Array of nested attributes, BSSID and status code, used by subcommand
+ * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each
+ * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info.
+ * The userspace space specifies the list/array of candidate BSSIDs in
+ * the order of preference in the request. The driver specifies the
+ * status code, for each BSSID in the list, in the response. The
+ * acceptable candidates are listed in the order preferred by the
+ * driver.
+ */
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37,
+ /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
+ * See enum qca_wlan_vendor_attr_brp_ant_limit_mode.
+ */
+ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38,
+ /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command
+ * to define the number of antennas to use for BRP.
+ * different purpose in each ANT_LIMIT_MODE:
+ * DISABLE - ignored
+ * EFFECTIVE - upper limit to number of antennas to be used
+ * FORCE - exact number of antennas to be used
+ * unsigned 8 bit value
+ */
+ QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39,
+ /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command
+ * to report the corresponding antenna index to the chain RSSI value */
+ QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS,
+ /* Indicates the status of re-association requested by user space for
+ * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID.
+ * Type u16.
+ * Represents the status code from AP. Use
+ * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the
+ * real status code for failures.
+ */
+ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS,
+ /* This attribute indicates that the old association was maintained when
+ * a re-association is requested by user space and that re-association
+ * attempt fails (i.e., cannot connect to the requested BSS, but can
+ * remain associated with the BSS with which the association was in
+ * place when being requested to roam). Used along with
+ * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current
+ * re-association status. Type flag.
+ * This attribute is applicable only for re-association failure cases.
+ */
+ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION,
+ /* This attribute specifies the PMK if one was newly generated during
+ * FILS roaming. This is added to the PMKSA cache and is used in
+ * subsequent connections with PMKSA caching.
+ */
+ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11,
+ /* This attribute specifies the PMKID used/generated for the current
+ * FILS roam. This is used in subsequent connections with PMKSA caching.
+ */
+ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12,
+ /* A 16-bit unsigned value specifying the next sequence number to use
+ * in ERP message in the currently associated realm. This is used in
+ * doing subsequent ERP based connections in the same realm.
+ */
+ QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX =
* Devices whilst in Listen state, rather than having the user space
* wpa_supplicant do it. Information from received P2P requests are
* forwarded from firmware to host whenever the host processor wakes up.
+ * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA
+ * specific features.
+ * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific
+ * features.
+ * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON
+ * specific features only. If a Device sets this bit but not the
+ * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that
+ * this Device may not support all OCE AP functionalities but can support
+ * only OCE STA-CFON functionalities.
* @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
*/
enum qca_wlan_vendor_features {
QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1,
QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2,
QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3,
+ QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4,
+ QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5,
+ QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6,
NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
};
QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1
};
+/**
+ * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set
+ * OCB config
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the
+ * configuration
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be
+ * scheduled
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel
+ * information
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL
+ * active state configuration
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as
+ * OCB_CONFIG_FLAG_80211_FRAME_MODE
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to
+ * use in the case that a packet is sent without a TX control header
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the
+ * last TA received that the local time set by TA is synchronous to other
+ * communicating OCB STAs.
+ */
+enum qca_wlan_vendor_attr_ocb_set_config {
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set
+ * UTC time
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of
+ * 10 bytes
+ * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of
+ * 5 bytes
+ */
+enum qca_wlan_vendor_attr_ocb_set_utc_time {
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX =
+ QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes
+ * to start sending timing advert frames
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency
+ * on which to send the frames
+ * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times
+ * the frame is sent in 5 seconds
+ */
+enum qca_wlan_vendor_attr_ocb_start_timing_advert {
+ QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1,
+ QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2,
+ QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX =
+ QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes
+ * to stop timing advert
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel
+ * frequency on which to stop the timing advert
+ */
+enum qca_wlan_vendor_attr_ocb_stop_timing_advert {
+ QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1,
+ QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX =
+ QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to
+ * get TSF timer value
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the
+ * timer
+ * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer
+ */
+enum qca_wlan_vendor_attr_ocb_get_tsf_resp {
+ QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1,
+ QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2,
+ QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX =
+ QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1
+};
+
enum qca_vendor_attr_get_preferred_freq_list {
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID,
/* A 32-unsigned value; the interface type/mode for which the preferred
* from kernel space to user space.
*/
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST,
+ /* An array of nested values as per enum qca_wlan_vendor_attr_pcl
+ * attribute. Each element contains frequency (MHz), weight, and flag
+ * bit mask indicating how the frequency should be used in P2P
+ * negotiation; sent from kernel space to user space.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX =
* vendor specific element is defined by the latest P802.11ax draft.
* Please note that the draft is still work in progress and this element
* payload is subject to change.
+ *
+ * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set
+ * element).
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID extension. The payload of
+ * this vendor specific element is defined by the latest P802.11ax draft
+ * (not including the Element ID Extension field). Please note that the
+ * draft is still work in progress and this element payload is subject to
+ * change.
+ *
+ * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID extension. The payload of
+ * this vendor specific element is defined by the latest P802.11ax draft
+ * (not including the Element ID Extension field). Please note that the
+ * draft is still work in progress and this element payload is subject to
+ * change.
+ *
+ * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID extension. The payload of
+ * this vendor specific element is defined by the latest P802.11ax draft
+ * (not including the Element ID Extension field). Please note that the
+ * draft is still work in progress and this element payload is subject to
+ * change.
*/
enum qca_vendor_element_id {
QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
QCA_VENDOR_ELEM_HE_CAPAB = 1,
QCA_VENDOR_ELEM_HE_OPER = 2,
+ QCA_VENDOR_ELEM_RAPS = 3,
+ QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4,
+ QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5,
};
/**
* scan flag is set
* @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
* randomisation
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
+ * specific BSSID to scan for.
*/
enum qca_wlan_vendor_attr_scan {
QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
- QCA_WLAN_VENDOR_ATTR_SCAN_IE,
- QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES,
- QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS,
- QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES,
- QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE,
- QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS,
- QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE,
- QCA_WLAN_VENDOR_ATTR_SCAN_STATUS,
- QCA_WLAN_VENDOR_ATTR_SCAN_MAC,
- QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK,
+ QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1,
+ QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2,
+ QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3,
+ QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4,
+ QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5,
+ QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6,
+ QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7,
+ QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10,
+ QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11,
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
* QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
*/
enum qca_wlan_vendor_attr_config {
- QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0,
/* Unsigned 32-bit value to set the DTIM period.
* Whether the wifi chipset wakes at every dtim beacon or a multiple of
* the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
* DTIM beacons.
*/
- QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1,
/* Unsigned 32-bit value to set the wifi_iface stats averaging factor
* used to calculate statistics like average the TSF offset or average
* number of frame leaked.
* For instance, when evaluating leaky APs:
* current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
*/
- QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2,
/* Unsigned 32-bit value to configure guard time, i.e., when
* implementing IEEE power management based on frame control PM bit, how
* long the driver waits before shutting down the radio and after
* receiving an ACK frame for a Data frame with PM bit set.
*/
- QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3,
/* Unsigned 32-bit value to change the FTM capability dynamically */
- QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4,
/* Unsigned 16-bit value to configure maximum TX rate dynamically */
- QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE,
+ QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5,
/* Unsigned 32-bit value to configure the number of continuous
* Beacon Miss which shall be used by the firmware to penalize
* the RSSI.
*/
- QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6,
/* Unsigned 8-bit value to configure the channel avoidance indication
* behavior. Firmware to send only one indication and ignore duplicate
* indications when set to avoid multiple Apps wakeups.
*/
- QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7,
/* 8-bit unsigned value to configure the maximum TX MPDU for
* aggregation. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8,
/* 8-bit unsigned value to configure the maximum RX MPDU for
* aggregation. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9,
/* 8-bit unsigned value to configure the Non aggregrate/11g sw
* retry threshold (0 disable, 31 max). */
- QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10,
/* 8-bit unsigned value to configure the aggregrate sw
* retry threshold (0 disable, 31 max). */
- QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11,
/* 8-bit unsigned value to configure the MGMT frame
* retry threshold (0 disable, 31 max). */
- QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12,
/* 8-bit unsigned value to configure the CTRL frame
* retry threshold (0 disable, 31 max). */
- QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13,
/* 8-bit unsigned value to configure the propagation delay for
* 2G/5G band (0~63, units in us) */
- QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14,
/* Unsigned 32-bit value to configure the number of unicast TX fail
* packet count. The peer is disconnected once this threshold is
* reached. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15,
/* Attribute used to set scan default IEs to the driver.
*
* These IEs can be used by scan operations that will be initiated by
* driver. If a particular IE is present in the scan default IEs but not
* present in the scan request, then that IE should be added to the IEs
* sent in the Probe Request frames for that scan request. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16,
/* Unsigned 32-bit attribute for generic commands */
- QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17,
/* Unsigned 32-bit value attribute for generic commands */
- QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18,
/* Unsigned 32-bit data attribute for generic command response */
- QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19,
/* Unsigned 32-bit length attribute for
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
- QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20,
/* Unsigned 32-bit flags attribute for
* QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
- QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21,
/* Unsigned 32-bit, defining the access policy.
* See enum qca_access_policy. Used with
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22,
/* Sets the list of full set of IEs for which a specific access policy
* has to be applied. Used along with
* QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
* Zero length payload can be used to clear this access constraint. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23,
/* Unsigned 32-bit, specifies the interface index (netdev) for which the
* corresponding configurations are applied. If the interface index is
* not specified, the configurations are attributed to the respective
* wiphy. */
- QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24,
+ /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25,
+ /* 8-bit unsigned value to configure the driver and below layers to
+ * ignore the assoc disallowed set by APs while connecting
+ * 1-Ignore, 0-Don't ignore */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26,
+ /* 32-bit unsigned value to trigger antenna diversity features:
+ * 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27,
+ /* 32-bit unsigned value to configure specific chain antenna */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28,
+ /* 32-bit unsigned value to trigger cycle selftest
+ * 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29,
+ /* 32-bit unsigned to configure the cycle time of selftest
+ * the unit is micro-second */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30,
+ /* 32-bit unsigned value to set reorder timeout for AC_VO */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31,
+ /* 32-bit unsigned value to set reorder timeout for AC_VI */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32,
+ /* 32-bit unsigned value to set reorder timeout for AC_BE */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33,
+ /* 32-bit unsigned value to set reorder timeout for AC_BK */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34,
+ /* 6-byte MAC address to point out the specific peer */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35,
+ /* 32-bit unsigned value to set window size for specific peer */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36,
+ /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37,
+ /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38,
+ /* 32-bit unsigned value to configure 5 or 10 MHz channel width for
+ * station device while in disconnect state. The attribute use the
+ * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz,
+ * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or
+ * 10 MHz channel width, the station will not connect to a BSS using 20
+ * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to
+ * clear this constraint. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39,
+ /* 32-bit unsigned value to configure the propagation absolute delay
+ * for 2G/5G band (units in us) */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40,
+ /* 32-bit unsigned value to set probe period */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41,
+ /* 32-bit unsigned value to set stay period */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42,
+ /* 32-bit unsigned value to set snr diff */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43,
+ /* 32-bit unsigned value to set probe dwell time */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44,
+ /* 32-bit unsigned value to set mgmt snr weight */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45,
+ /* 32-bit unsigned value to set data snr weight */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46,
+ /* 32-bit unsigned value to set ack snr weight */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47,
+ /* 32-bit unsigned value to configure the listen interval.
+ * This is in units of beacon intervals. This configuration alters
+ * the negotiated listen interval with the AP during the connection.
+ * It is highly recommended to configure a value less than or equal to
+ * the one negotiated during the association. Configuring any greater
+ * value can have adverse effects (frame loss, AP disassociating STA,
+ * etc.).
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48,
+ /*
+ * 8 bit unsigned value that is set on an AP/GO virtual interface to
+ * disable operations that would cause the AP/GO to leave its operating
+ * channel.
+ *
+ * This will restrict the scans to the AP/GO operating channel and the
+ * channels of the other band, if DBS is supported.A STA/CLI interface
+ * brought up after this setting is enabled, will be restricted to
+ * connecting to devices only on the AP/GO interface's operating channel
+ * or on the other band in DBS case. P2P supported channel list is
+ * modified, to only include AP interface's operating-channel and the
+ * channels of the other band if DBS is supported.
+ *
+ * These restrictions are only applicable as long as the AP/GO interface
+ * is alive. If the AP/GO interface is brought down then this
+ * setting/restriction is forgotten.
+ *
+ * If this variable is set on an AP/GO interface while a multi-channel
+ * concurrent session is active, it has no effect on the operation of
+ * the current interfaces, other than restricting the scan to the AP/GO
+ * operating channel and the other band channels if DBS is supported.
+ * However, if the STA is brought down and restarted then the new STA
+ * connection will either be formed on the AP/GO channel or on the
+ * other band in a DBS case. This is because of the scan being
+ * restricted on these channels as mentioned above.
+ *
+ * 1-Restrict / 0-Don't restrict offchannel operations.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49,
+ /*
+ * 8 bit unsigned value to enable/disable LRO (Large Receive Offload)
+ * on an interface.
+ * 1 - Enable, 0 - Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50,
+
+ /*
+ * 8 bit unsigned value to globally enable/disable scan
+ * 1 - Enable, 0 - Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51,
+
+ /* 8-bit unsigned value to set the total beacon miss count
+ * This paramater will set the total beacon miss count.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52,
+
+ /* Unsigned 32-bit value to configure the number of continuous
+ * Beacon Miss which shall be used by the firmware to penalize
+ * the RSSI for BTC.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53,
+
+ /* 8-bit unsigned value to configure the driver and below layers to
+ * enable/disable all FILS features.
+ * 0-enable, 1-disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54,
+
+ /* 16-bit unsigned value to configure the level of WLAN latency
+ * module. See enum qca_wlan_vendor_attr_config_latency_level.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55,
+
+ /* 8-bit unsigned value indicating the driver to use the RSNE as-is from
+ * the connect interface. Exclusively used for the scenarios where the
+ * device is used as a test bed device with special functionality and
+ * not recommended for production. This helps driver to not validate the
+ * RSNE passed from user space and thus allow arbitrary IE data to be
+ * used for testing purposes.
+ * 1-enable, 0-disable.
+ * Applications set/reset this configuration. If not reset, this
+ * parameter remains in use until the driver is unloaded.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
};
+/**
+ * qca_wlan_set_qdepth_thresh_attr - Parameters for setting
+ * MSDUQ depth threshold per peer per tid in the target
+ *
+ * Associated Vendor Command:
+ * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH
+ */
+enum qca_wlan_set_qdepth_thresh_attr {
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0,
+ /* 6-byte MAC address */
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR,
+ /* Unsigned 32-bit attribute for holding the TID */
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID,
+ /* Unsigned 32-bit attribute for holding the update mask
+ * bit 0 - Update high priority msdu qdepth threshold
+ * bit 1 - Update low priority msdu qdepth threshold
+ * bit 2 - Update UDP msdu qdepth threshold
+ * bit 3 - Update Non UDP msdu qdepth threshold
+ * rest of bits are reserved
+ */
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK,
+ /* Unsigned 32-bit attribute for holding the threshold value */
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST,
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX =
+ QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
+ */
+enum qca_wlan_vendor_attr_get_hw_capability {
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
+ /* Antenna isolation
+ * An attribute used in the response.
+ * The content of this attribute is encoded in a byte array. Each byte
+ * value is an antenna isolation value. The array length is the number
+ * of antennas.
+ */
+ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
+ /* Request HW capability
+ * An attribute used in the request.
+ * The content of this attribute is a u32 array for one or more of
+ * hardware capabilities (attribute IDs) that are being requested. Each
+ * u32 value has a value from this
+ * enum qca_wlan_vendor_attr_get_hw_capability
+ * identifying which capabilities are requested.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
+ * offload which is an extension for LL_STATS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
+ * If MAC counters do not exceed the threshold, FW will report monitored
+ * link layer counters periodically as this setting. The first report is
+ * always triggered by this timer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
+ * For each MAC layer counter, FW holds two copies. One is the current value.
+ * The other is the last report. Once a current counter's increment is larger
+ * than the threshold, FW will indicate that counter to host even if the
+ * monitoring timer does not expire.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
+ * failure code.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
+ * 1: TX packet discarded
+ * 2: No ACK
+ * 3: Postpone
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold.
+ * Threshold for all monitored parameters. If per counter dedicated threshold
+ * is not enabled, this threshold will take effect.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this
+ * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters
+ * Bit0: TX counter unit in MSDU
+ * Bit1: TX counter unit in MPDU
+ * Bit2: TX counter unit in PPDU
+ * Bit3: TX counter unit in byte
+ * Bit4: Dropped MSDUs
+ * Bit5: Dropped Bytes
+ * Bit6: MPDU retry counter
+ * Bit7: MPDU failure counter
+ * Bit8: PPDU failure counter
+ * Bit9: MPDU aggregation counter
+ * Bit10: MCS counter for ACKed MPDUs
+ * Bit11: MCS counter for Failed MPDUs
+ * Bit12: TX Delay counter
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters
+ * Bit0: MAC RX counter unit in MPDU
+ * Bit1: MAC RX counter unit in byte
+ * Bit2: PHY RX counter unit in PPDU
+ * Bit3: PHY RX counter unit in byte
+ * Bit4: Disorder counter
+ * Bit5: Retry counter
+ * Bit6: Duplication counter
+ * Bit7: Discard counter
+ * Bit8: MPDU aggregation size counter
+ * Bit9: MCS counter
+ * Bit10: Peer STA power state change (wake to sleep) counter
+ * Bit11: Peer STA power save counter, total time in PS mode
+ * Bit12: Probe request counter
+ * Bit13: Other management frames counter
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA
+ * Bit0: Idle time
+ * Bit1: TX time
+ * Bit2: time RX in current bss
+ * Bit3: Out of current bss time
+ * Bit4: Wireless medium busy time
+ * Bit5: RX in bad condition time
+ * Bit6: TX in bad condition time
+ * Bit7: time wlan card not available
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal
+ * Bit0: Per channel SNR counter
+ * Bit1: Per channel noise floor counter
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM:
+ * aggregation stats buffer length
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats
+ * buffer for ACKed MPDUs.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats
+ * buffer for failed MPDUs.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE:
+ * length of delay stats array.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets
+ * flagged as retransmissions
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets
+ * flagged as duplicated
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX
+ * packets discarded
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation
+ * stats buffer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs
+ * stats buffer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe
+ * requests received
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt
+ * frames received
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time
+ * there is no TX, nor RX, nor interference.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time
+ * transmitting packets.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time
+ * for receiving.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time
+ * interference detected.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time
+ * receiving packets with errors.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time
+ * TX no-ACK.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time
+ * the chip is unable to work in normal conditions.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time
+ * receiving packets in current BSS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time
+ * receiving packets not in current BSS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL:
+ * This is a container for per antenna signal stats.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64
+ * Absolute timestamp from 1970/1/1, unit in ms. After receiving the
+ * message, user layer APP could call gettimeofday to get another
+ * timestamp and calculate transfer delay for the message.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32
+ * Real period for this measurement, unit in us.
+ */
+enum qca_wlan_vendor_attr_ll_stats_ext {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
+
+ /* Attributes for configurations */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
+
+ /* Peer STA power state change */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
+
+ /* TX failure event */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS,
+
+ /* MAC counters */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER,
+
+ /* Sub-attributes for PEER_AC_TX */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY,
+
+ /* Sub-attributes for PEER_AC_RX */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT,
+
+ /* Sub-attributes for CCA_BSS */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL,
+
+ /* sub-attribute for BSS_RX_TIME */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME,
+
+ /* Sub-attributes for PEER_SIGNAL */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF,
+
+ /* Sub-attributes for IFACE_BSS */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
+};
+
+/* Attributes for FTM commands and events */
+
+/**
+ * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities
+ *
+ * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See
+ * enum qca_wlan_vendor_attr_loc_capa_flags.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number
+ * of measurement sessions that can run concurrently.
+ * Default is one session (no session concurrency).
+ * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique
+ * peers that are supported in running sessions. For example,
+ * if the value is 8 and maximum number of sessions is 2, you can
+ * have one session with 8 unique peers, or 2 sessions with 4 unique
+ * peers each, and so on.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number
+ * of bursts per peer, as an exponent (2^value). Default is 0,
+ * meaning no multi-burst support.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number
+ * of measurement exchanges allowed in a single burst.
+ * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement
+ * types. A bit mask (unsigned 32 bit value), each bit corresponds
+ * to an AOA type as defined by enum qca_vendor_attr_aoa_type.
+ */
+enum qca_wlan_vendor_attr_loc_capa {
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID,
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS,
+ QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS,
+ QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS,
+ QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP,
+ QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST,
+ QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX =
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags
+ *
+ * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver
+ * can be configured as an FTM responder (for example, an AP that
+ * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER
+ * will be supported if set.
+ * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver
+ * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION
+ * will be supported if set.
+* @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder
+ * supports immediate (ASAP) response.
+ * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone
+ * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS.
+ * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports
+ * requesting AOA measurements as part of an FTM session.
+ */
+enum qca_wlan_vendor_attr_loc_capa_flags {
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0,
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1,
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2,
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3,
+ QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_peer_info: Information about
+ * a single peer in a measurement session.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related
+ * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of
+ * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0
+ * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for
+ * list of supported attributes.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for
+ * secure measurement.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA
+ * measurement every <value> bursts. If 0 or not specified,
+ * AOA measurements will be disabled for this peer.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where
+ * the measurement frames are exchanged. Optional; if not
+ * specified, try to locate the peer in the kernel scan
+ * results cache and use frequency from there.
+ */
+enum qca_wlan_vendor_attr_ftm_peer_info {
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX =
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags,
+ * per-peer
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request
+ * immediate (ASAP) response from peer.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request
+ * LCI report from peer. The LCI report includes the absolute
+ * location of the peer in "official" coordinates (similar to GPS).
+ * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request
+ * Location civic report from peer. The LCR includes the location
+ * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0,
+ * 11.24.6.7 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set,
+ * request a secure measurement.
+ * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided.
+ */
+enum qca_wlan_vendor_attr_ftm_peer_meas_flags {
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements
+ * to perform in a single burst.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to
+ * perform, specified as an exponent (2^value).
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst
+ * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts,
+ * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must
+ * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION.
+ */
+enum qca_wlan_vendor_attr_ftm_meas_param {
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID,
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST,
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP,
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION,
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported
+ * peer.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement
+ * request for this peer.
+ * See enum qca_wlan_vendor_attr_ftm_peer_result_status.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related
+ * to measurement results for this peer.
+ * See enum qca_wlan_vendor_attr_ftm_peer_result_flags.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when
+ * request failed and peer requested not to send an additional request
+ * for this number of seconds.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received
+ * from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
+ * 9.4.2.22.10.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when
+ * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0,
+ * 9.4.2.22.13.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer
+ * overridden some measurement request parameters. See
+ * enum qca_wlan_vendor_attr_ftm_meas_param.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement
+ * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement
+ * results. Each entry is a nested attribute defined
+ * by enum qca_wlan_vendor_attr_ftm_meas.
+ */
+enum qca_wlan_vendor_attr_ftm_peer_result {
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX =
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_peer_result_status
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results
+ * will be provided. Peer may have overridden some measurement parameters,
+ * in which case overridden parameters will be report by
+ * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable
+ * of performing the measurement request. No more results will be sent
+ * for this peer in this session.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request
+ * failed, and requested not to send an additional request for number
+ * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS
+ * attribute.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation
+ * failed. Request was not sent over the air.
+ */
+enum qca_wlan_vendor_attr_ftm_peer_result_status {
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED,
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags
+ * for measurement result, per-peer
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set,
+ * measurement completed for this peer. No more results will be reported
+ * for this peer in this session.
+ */
+enum qca_wlan_vendor_attr_ftm_peer_result_flags {
+ QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0,
+};
+
+/**
+ * enum qca_vendor_attr_loc_session_status: Session completion status code
+ *
+ * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed
+ * successfully.
+ * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted
+ * by request.
+ * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request
+ * was invalid and was not started.
+ * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error
+ * and did not complete normally (for example out of resources).
+ */
+enum qca_vendor_attr_loc_session_status {
+ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK,
+ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED,
+ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID,
+ QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data
+ *
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as
+ * recorded by responder, in picoseconds.
+ * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at
+ * initiator, in picoseconds.
+ * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by
+ * initiator, in picoseconds.
+ * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at
+ * responder, in picoseconds.
+ * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded
+ * during this measurement exchange. Optional and will be provided if
+ * the hardware can measure it.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by
+ * responder. Not always provided.
+ * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by
+ * responder. Not always provided.
+ * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by
+ * initiator. Not always provided.
+ * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by
+ * initiator. Not always provided.
+ * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information.
+ * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding.
+ */
+enum qca_wlan_vendor_attr_ftm_meas {
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX =
+ QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type
+ *
+ * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest
+ * CIR (channel impulse response) path for each antenna.
+ * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude
+ * of the strongest CIR path for each antenna.
+ */
+enum qca_wlan_vendor_attr_aoa_type {
+ QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE,
+ QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP,
+ QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX
+};
+
+/**
+ * enum qca_wlan_vendor_attr_encryption_test - Attributes to
+ * validate encryption engine
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute.
+ * This will be included if the request is for decryption; if not included,
+ * the request is treated as a request for encryption by default.
+ * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value
+ * indicating the key cipher suite. Takes same values as
+ * NL80211_ATTR_KEY_CIPHER.
+ * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value
+ * Key Id to be used for encryption
+ * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values.
+ * Key (TK) to be used for encryption/decryption
+ * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values.
+ * Packet number to be specified for encryption/decryption
+ * 6 bytes for TKIP/CCMP/GCMP.
+ * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values
+ * representing the 802.11 packet (header + payload + FCS) that
+ * needs to be encrypted/decrypted.
+ * Encrypted/decrypted response from the driver will also be sent
+ * to userspace with the same attribute.
+ */
+enum qca_wlan_vendor_attr_encryption_test {
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX =
+ QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of
+ * sector for DMG RF sector operations.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector
+ */
+enum qca_wlan_vendor_attr_dmg_rf_sector_type {
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX
+};
+
+/**
+ * BRP antenna limit mode
+ *
+ * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force
+ * antenna limit, BRP will be performed as usual.
+ * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal
+ * antennas limit. the hardware may use less antennas than the
+ * maximum limit.
+ * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will
+ * use exactly the specified number of antennas for BRP.
+ */
+enum qca_wlan_vendor_attr_brp_ant_limit_mode {
+ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE,
+ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE,
+ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE,
+ QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX
+};
+
+/**
+ * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for
+ * DMG RF sector configuration for a single RF module.
+ * The values are defined in a compact way which closely matches
+ * the way it is stored in HW registers.
+ * The configuration provides values for 32 antennas and 8 distribution
+ * amplifiers, and together describes the characteristics of the RF
+ * sector - such as a beam in some direction with some gain.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index
+ * of RF module for this configuration.
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge
+ * amplifier gain index. Unsigned 32 bit number containing
+ * bits for all 32 antennas.
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge
+ * amplifier gain index. Unsigned 32 bit number containing
+ * bits for all 32 antennas.
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge
+ * amplifier gain index. Unsigned 32 bit number containing
+ * bits for all 32 antennas.
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values
+ * for first 16 antennas, 2 bits per antenna.
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values
+ * for last 16 antennas, 2 bits per antenna.
+ * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains
+ * DTYPE values (3 bits) for each distribution amplifier, followed
+ * by X16 switch bits for each distribution amplifier. There are
+ * total of 8 distribution amplifiers.
+ */
+enum qca_wlan_vendor_attr_dmg_rf_sector_cfg {
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX =
+ QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1
+};
+
+enum qca_wlan_vendor_attr_ll_stats_set {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_ll_stats_clr {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0,
+ /* Unsigned 32bit bitmap for clearing statistics
+ * All radio statistics 0x00000001
+ * cca_busy_time (within radio statistics) 0x00000002
+ * All channel stats (within radio statistics) 0x00000004
+ * All scan statistics (within radio statistics) 0x00000008
+ * All interface statistics 0x00000010
+ * All tx rate statistics (within interface statistics) 0x00000020
+ * All ac statistics (with in interface statistics) 0x00000040
+ * All contention (min, max, avg) statistics (within ac statisctics)
+ * 0x00000080.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1,
+ /* Unsigned 8 bit value: Request to stop statistics collection */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2,
+
+ /* Unsigned 32 bit bitmap: Response from the driver
+ * for the cleared statistics
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3,
+ /* Unsigned 8 bit value: Response from driver/firmware
+ * for the stop request
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_ll_stats_get {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0,
+ /* Unsigned 32 bit value provided by the caller issuing the GET stats
+ * command. When reporting the stats results, the driver uses the same
+ * value to indicate which GET request the results correspond to.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1,
+ /* Unsigned 32 bit value - bit mask to identify what statistics are
+ * requested for retrieval.
+ * Radio Statistics 0x00000001
+ * Interface Statistics 0x00000020
+ * All Peer Statistics 0x00000040
+ * Peer Statistics 0x00000080
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_ll_stats_results {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0,
+ /* Unsigned 32bit value. Used by the driver; must match the request id
+ * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2,
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3,
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4,
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5,
+ /* Signed 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6,
+ /* Signed 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7,
+ /* Signed 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8,
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are
+ * nested within the interface stats.
+ */
+
+ /* Interface mode, e.g., STA, SOFTAP, IBSS, etc.
+ * Type = enum wifi_interface_mode.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9,
+ /* Interface MAC address. An array of 6 Unsigned int8 */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10,
+ /* Type = enum wifi_connection_state, e.g., DISCONNECTED,
+ * AUTHENTICATING, etc. valid for STA, CLI only.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11,
+ /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12,
+ /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13,
+ /* NULL terminated SSID. An array of 33 Unsigned 8bit values */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14,
+ /* BSSID. An array of 6 unsigned 8 bit values */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15,
+ /* Country string advertised by AP. An array of 3 unsigned 8 bit
+ * values.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16,
+ /* Country string for this association. An array of 3 unsigned 8 bit
+ * values.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17,
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could
+ * be nested within the interface stats.
+ */
+
+ /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26,
+ /* Unsigned int 32 value corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27,
+ /* Unsigned int 32 values corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28,
+ /* Unsigned int 32 values corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29,
+ /* Unsigned int 32 values corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30,
+ /* Unsigned int 32 values corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31,
+ /* Unsigned int 32 values corresponding to respective AC */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32,
+ /* Unsigned 32 bit value. Number of peers */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33,
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are
+ * nested within the interface stats.
+ */
+
+ /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34,
+ /* MAC addr corresponding to respective peer. An array of 6 unsigned
+ * 8 bit values.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35,
+ /* Unsigned int 32 bit value representing capabilities corresponding
+ * to respective peer.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36,
+ /* Unsigned 32 bit value. Number of rates */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37,
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
+ * are nested within the rate stat.
+ */
+
+ /* Wi-Fi Rate - separate attributes defined for individual fields */
+
+ /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38,
+ /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39,
+ /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40,
+ /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std
+ * in the units of 0.5 Mbps HT/VHT it would be MCS index */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41,
+
+ /* Unsigned 32 bit value. Bit rate in units of 100 kbps */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42,
+
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be
+ * nested within the peer info stats.
+ */
+
+ /* Unsigned int 32 bit value. Number of successfully transmitted data
+ * packets, i.e., with ACK received corresponding to the respective
+ * rate.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43,
+ /* Unsigned int 32 bit value. Number of received data packets
+ * corresponding to the respective rate.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44,
+ /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK
+ * received corresponding to the respective rate.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45,
+ /* Unsigned int 32 bit value. Total number of data packet retries for
+ * the respective rate.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46,
+ /* Unsigned int 32 bit value. Total number of short data packet retries
+ * for the respective rate.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47,
+ /* Unsigned int 32 bit value. Total number of long data packet retries
+ * for the respective rate.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake
+ * accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50,
+ /* Unsigned 32 bit value. Total number of msecs the radio is
+ * transmitting accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51,
+ /* Unsigned 32 bit value. Total number of msecs the radio is in active
+ * receive accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake due
+ * to all scan accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake due
+ * to NAN accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake due
+ * to GSCAN accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake due
+ * to roam scan accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake due
+ * to PNO scan accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57,
+ /* Unsigned 32 bit value. Total number of msecs the radio is awake due
+ * to Hotspot 2.0 scans and GAS exchange accruing over time.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58,
+ /* Unsigned 32 bit value. Number of channels. */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59,
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could
+ * be nested within the channel stats.
+ */
+
+ /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60,
+ /* Unsigned 32 bit value. Primary 20 MHz channel. */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61,
+ /* Unsigned 32 bit value. Center frequency (MHz) first segment. */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62,
+ /* Unsigned 32 bit value. Center frequency (MHz) second segment. */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63,
+
+ /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be
+ * nested within the radio stats.
+ */
+
+ /* Unsigned int 32 bit value representing total number of msecs the
+ * radio is awake on that channel accruing over time, corresponding to
+ * the respective channel.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64,
+ /* Unsigned int 32 bit value representing total number of msecs the CCA
+ * register is busy accruing over time corresponding to the respective
+ * channel.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66,
+
+ /* Signifies the nested list of channel attributes
+ * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_*
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67,
+
+ /* Signifies the nested list of peer info attributes
+ * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_*
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68,
+
+ /* Signifies the nested list of rate info attributes
+ * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_*
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69,
+
+ /* Signifies the nested list of wmm info attributes
+ * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_*
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70,
+
+ /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates
+ * that more stats, e.g., peers or radio, are to follow in the next
+ * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event.
+ * Otherwise, it is set to 0.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71,
+
+ /* Unsigned 64 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77,
+
+ /* Number of msecs the radio spent in transmitting for each power level
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78,
+
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79,
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80,
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81,
+ /* Unsigned 32 bit value */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82,
+
+ /* Unsigned int 32 value.
+ * Pending MSDUs corresponding to respective AC.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_ll_stats_type
+{
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3,
+
+ /* keep last */
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX =
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for
+ * TDLS configuration to the host driver.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger
+ * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode
+ * represents the different TDLS trigger modes.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within
+ * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number
+ * of packets shall meet the criteria for implicit TDLS setup.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets
+ * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD
+ * to initiate a TDLS setup.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate
+ * a TDLS Discovery to the peer.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of
+ * discovery attempts to know the TDLS capability of the peer. A peer is
+ * marked as TDLS not capable if there is no response for all the attempts.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32)
+ * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD
+ * number of TX / RX frames meet the criteria for TDLS teardown.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32)
+ * of Tx/Rx packets within a duration
+ * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold
+ * corresponding to the RSSI of the peer below which a TDLS setup is
+ * triggered.
+ * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold
+ * corresponding to the RSSI of the peer above which a TDLS teardown is
+ * triggered.
+ */
+enum qca_wlan_vendor_attr_tdls_configuration {
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1,
+
+ /* Attributes configuring the TDLS Implicit Trigger */
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in
+ * the driver
+ *
+ * The following are the different values for
+ * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE.
+ *
+ * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown
+ * the TDLS connection to a respective peer comes from the user space.
+ * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN,
+ * TDLS_DISCOVER to do this.
+ * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS
+ * setup/teardown to the eligible peer once the configured criteria
+ * (such as TX/RX threshold, RSSI) is met. The attributes
+ * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to
+ * the different configuration criteria for the TDLS trigger from the
+ * host driver.
+ * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger
+ * the TDLS setup / teardown through the implicit mode only to the
+ * configured MAC addresses (wpa_supplicant, with tdls_external_control=1,
+ * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands).
+ * External mode works on top of the implicit mode. Thus the host driver
+ * is expected to configure in TDLS Implicit mode too to operate in
+ * External mode.
+ * Configuring External mode alone without Implicit mode is invalid.
+ *
+ * All the above implementations work as expected only when the host driver
+ * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing
+ * that the TDLS message exchange is not internal to the host driver, but
+ * depends on wpa_supplicant to do the message exchange.
+ */
+enum qca_wlan_vendor_tdls_trigger_mode {
+ QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0,
+ QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1,
+ QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2,
+};
+
+/**
+ * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
+ * source of SAR power limits, thereby disabling the SAR power
+ * limit feature.
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
+ * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
+ *
+ * This enumerates the valid set of values that may be supplied for
+ * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
+ * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in
+ * the response to an instance of the
+ * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
+ */
+enum qca_vendor_attr_sar_limits_selections {
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6,
+};
+
+/**
+ * enum qca_vendor_attr_sar_limits_spec_modulations -
+ * SAR limits specification modulation
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
+ * CCK modulation
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
+ * OFDM modulation
+ *
+ * This enumerates the valid set of values that may be supplied for
+ * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
+ * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
+ * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
+ * command or in the response to an instance of the
+ * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command.
+ */
+enum qca_vendor_attr_sar_limits_spec_modulations {
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1,
+};
+
+/**
+ * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to
+ * select which SAR power limit table should be used. Valid
+ * values are enumerated in enum
+ * %qca_vendor_attr_sar_limits_selections. The existing SAR
+ * power limit selection is unchanged if this attribute is not
+ * present.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
+ * which specifies the number of SAR power limit specifications
+ * which will follow.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
+ * limit specifications. The number of specifications is
+ * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
+ * specification contains a set of
+ * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
+ * specification is uniquely identified by the attributes
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
+ * contains as a payload the attribute
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
+ * indicate for which band this specification applies. Valid
+ * values are enumerated in enum %nl80211_band (although not all
+ * bands may be supported by a given device). If the attribute is
+ * not supplied then the specification will be applied to all
+ * supported bands.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
+ * to indicate for which antenna chain this specification
+ * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
+ * attribute is not supplied then the specification will be
+ * applied to all chains.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
+ * value to indicate for which modulation scheme this
+ * specification applies. Valid values are enumerated in enum
+ * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
+ * is not supplied then the specification will be applied to all
+ * modulation schemes.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
+ * value to specify the actual power limit value in units of 0.5
+ * dBm (i.e., a value of 11 represents 5.5 dBm).
+ *
+ * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS
+ * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS.
+ */
+enum qca_vendor_attr_sar_limits {
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7,
+
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
+ */
+enum qca_wlan_vendor_attr_get_wifi_info {
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX =
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1,
+};
+
+/*
+ * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command.
+ */
+enum qca_wlan_vendor_attr_wifi_logger_start {
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX =
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_logger_results {
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0,
+
+ /* Unsigned 32-bit value; must match the request Id supplied by
+ * Wi-Fi HAL in the corresponding subcmd NL msg.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1,
+
+ /* Unsigned 32-bit value; used to indicate the size of memory
+ * dump to be allocated.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX =
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_roaming_config_params {
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0,
+
+ QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2,
+
+ /* Attributes for wifi_set_ssid_white_list */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5,
+
+ /* Attributes for set_roam_params */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12,
+
+ /* Attribute for set_lazy_roam */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13,
+
+ /* Attribute for set_lazy_roam with preferences */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17,
+
+ /* Attribute for set_blacklist bssid params */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1,
+};
+
+/*
+ * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
+ */
+enum qca_wlan_vendor_attr_roam_subcmd {
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX =
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_gscan_config_params {
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0,
+
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1,
+
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND
+ = 2,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS
+ = 3,
+
+ /* Attributes for input params used by
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command.
+ */
+
+ /* Unsigned 32-bit value; channel frequency */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4,
+ /* Unsigned 32-bit value; dwell time in ms. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5,
+ /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6,
+ /* Unsigned 8-bit value; channel class */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7,
+
+ /* Unsigned 8-bit value; bucket index, 0 based */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8,
+ /* Unsigned 8-bit value; band. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9,
+ /* Unsigned 32-bit value; desired period, in ms. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10,
+ /* Unsigned 8-bit value; report events semantics. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11,
+ /* Unsigned 32-bit value. Followed by a nested array of
+ * GSCAN_CHANNEL_SPEC_* attributes.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12,
+
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13,
+
+ /* Unsigned 32-bit value; base timer period in ms. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14,
+ /* Unsigned 32-bit value; number of APs to store in each scan in the
+ * BSSID/RSSI history buffer (keep the highest RSSI APs).
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15,
+ /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake
+ * up AP.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT
+ = 16,
+
+ /* Unsigned 8-bit value; number of scan bucket specs; followed by a
+ * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size
+ * of the array is determined by NUM_BUCKETS.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17,
+
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18,
+
+ /* Unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH
+ = 19,
+ /* Unsigned 32-bit value; maximum number of results to be returned. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX
+ = 20,
+
+ /* An array of 6 x unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24,
+
+ /* Number of hotlist APs as unsigned 32-bit value, followed by a nested
+ * array of AP_THRESHOLD_PARAM attributes and values. The size of the
+ * array is determined by NUM_AP.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25,
+
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26,
+
+ /* Unsigned 32-bit value; number of samples for averaging RSSI. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE
+ = 27,
+ /* Unsigned 32-bit value; number of samples to confirm AP loss. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE
+ = 28,
+ /* Unsigned 32-bit value; number of APs breaching threshold. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29,
+ /* Unsigned 32-bit value; number of APs. Followed by an array of
+ * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30,
+ /* Unsigned 32-bit value; number of samples to confirm AP loss. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE
+ = 31,
+ /* Unsigned 32-bit value. If max_period is non zero or different than
+ * period, then this bucket is an exponential backoff bucket.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32,
+ /* Unsigned 32-bit value. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33,
+ /* Unsigned 32-bit value. For exponential back off bucket, number of
+ * scans to perform for a given period.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34,
+ /* Unsigned 8-bit value; in number of scans, wake up AP after these
+ * many scans.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS
+ = 35,
+
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command.
+ */
+ /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE
+ = 36,
+ /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a
+ * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The
+ * size of the array is determined by NUM_SSID.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37,
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_*
+ * attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38,
+
+ /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39,
+ /* Unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42,
+ /* Unsigned 32-bit value; a bitmask with additional gscan config flag.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_gscan_results {
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0,
+
+ /* Unsigned 32-bit value; must match the request Id supplied by
+ * Wi-Fi HAL in the corresponding subcmd NL msg.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1,
+
+ /* Unsigned 32-bit value; used to indicate the status response from
+ * firmware/driver for the vendor sub-command.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2,
+
+ /* GSCAN Valid Channels attributes */
+ /* Unsigned 32bit value; followed by a nested array of CHANNELS. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3,
+ /* An array of NUM_CHANNELS x unsigned 32-bit value integers
+ * representing channel numbers.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4,
+
+ /* GSCAN Capabilities attributes */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN
+ = 7,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE
+ = 8,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD
+ = 9,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS
+ = 11,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES
+ = 12,
+
+ /* GSCAN Attributes used with
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command.
+ */
+
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13,
+
+ /* GSCAN attributes used with
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command.
+ */
+
+ /* An array of NUM_RESULTS_AVAILABLE x
+ * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_*
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14,
+
+ /* Unsigned 64-bit value; age of sample at the time of retrieval */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15,
+ /* 33 x unsigned 8-bit value; NULL terminated SSID */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16,
+ /* An array of 6 x unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17,
+ /* Unsigned 32-bit value; channel frequency in MHz */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21,
+ /* Unsigned 16-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22,
+ /* Unsigned 16-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23,
+ /* Unsigned 32-bit value; size of the IE DATA blob */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24,
+ /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the
+ * information elements found in the beacon; this data should be a
+ * packed list of wifi_information_element objects, one after the
+ * other.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25,
+
+ /* Unsigned 8-bit value; set by driver to indicate more scan results are
+ * available.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26,
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command.
+ */
+ /* Unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28,
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command.
+ */
+ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
+ * to indicate number of results.
+ * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
+ * list of results.
+ */
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command.
+ */
+ /* An array of 6 x unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL
+ = 30,
+ /* Unsigned 32-bit value. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI
+ = 31,
+ /* A nested array of signed 32-bit RSSI values. Size of the array is
+ * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST
+ = 32,
+
+ /* GSCAN attributes used with
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command.
+ */
+ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
+ * to indicate number of gscan cached results returned.
+ * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate
+ * the list of gscan cached results.
+ */
+
+ /* An array of NUM_RESULTS_AVAILABLE x
+ * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_*
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33,
+ /* Unsigned 32-bit value; a unique identifier for the scan unit. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34,
+ /* Unsigned 32-bit value; a bitmask w/additional information about scan.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35,
+ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
+ * to indicate number of wifi scan results/bssids retrieved by the scan.
+ * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
+ * list of wifi scan results returned for each cached result block.
+ */
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command.
+ */
+ /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for
+ * number of results.
+ * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
+ * list of wifi scan results returned for each
+ * wifi_passpoint_match_result block.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE.
+ */
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES
+ = 36,
+ /* A nested array of
+ * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_*
+ * attributes. Array size =
+ * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37,
+
+ /* Unsigned 32-bit value; network block id for the matched network */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38,
+ /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
+ * list of wifi scan results returned for each
+ * wifi_passpoint_match_result block.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39,
+ /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values;
+ * ANQP data in the information_element format.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40,
+
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41,
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42,
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID
+ = 43,
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID
+ = 44,
+
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX =
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_pno_config_params {
+ QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0,
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1,
+ /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_*
+ * attributes. Array size =
+ * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2,
+
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3,
+ /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded
+ * realm, 0 if unspecified.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4,
+ /* An array of 16 x unsigned 32-bit value; roaming consortium ids to
+ * match, 0 if unspecified.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5,
+ /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if
+ * unspecified.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6,
+
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7,
+ /* Array of nested
+ * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_*
+ * attributes. Array size =
+ * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8,
+ /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9,
+ /* Signed 8-bit value; threshold for considering this SSID as found,
+ * required granularity for this threshold is 4 dBm to 8 dBm.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD
+ = 10,
+ /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11,
+ /* Unsigned 8-bit value; auth bit field for matching WPA IE */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12,
+ /* Unsigned 8-bit to indicate ePNO type;
+ * It takes values from qca_wlan_epno_type
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13,
+
+ /* Nested attribute to send the channel list */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14,
+
+ /* Unsigned 32-bit value; indicates the interval between PNO scan
+ * cycles in msec.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15,
+ QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16,
+ QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17,
+ QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18,
+ QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19,
+ QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20,
+ QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21,
+ QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22,
+ /* Unsigned 32-bit value, representing the PNO Request ID */
+ QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_PNO_MAX =
+ QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_acs_select_reason: This represents the different reasons why
+ * the ACS has to be triggered. These values are used by
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
+ */
+enum qca_wlan_vendor_acs_select_reason {
+ /* Represents the reason that the ACS triggered during the AP start */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT,
+ /* Represents the reason that DFS found with the current channel */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS,
+ /* Represents the reason that LTE co-exist in the current band. */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX,
+};
+
+/**
+ * qca_wlan_vendor_attr_external_acs_policy: Attribute values for
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the
+ * external ACS policies to select the channels w.r.t. the PCL weights.
+ * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and
+ * their PCL weights.)
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to
+ * select a channel with non-zero PCL weight.
+ * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a
+ * channel with non-zero PCL weight.
+ *
+ */
+enum qca_wlan_vendor_attr_external_acs_policy {
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY,
+};
+
+/**
+ * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel.
+ * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS.
+ */
+enum qca_wlan_vendor_channel_prop_flags {
+ /* Bits 0, 1, 2, and 3 are reserved */
+
+ /* Turbo channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4,
+ /* CCK channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5,
+ /* OFDM channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6,
+ /* 2.4 GHz spectrum channel. */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7,
+ /* 5 GHz spectrum channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8,
+ /* Only passive scan allowed */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9,
+ /* Dynamic CCK-OFDM channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10,
+ /* GFSK channel (FHSS PHY) */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11,
+ /* Radar found on channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12,
+ /* 11a static turbo channel only */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13,
+ /* Half rate channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14,
+ /* Quarter rate channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15,
+ /* HT 20 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16,
+ /* HT 40 with extension channel above */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17,
+ /* HT 40 with extension channel below */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18,
+ /* HT 40 intolerant */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19,
+ /* VHT 20 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20,
+ /* VHT 40 with extension channel above */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21,
+ /* VHT 40 with extension channel below */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22,
+ /* VHT 80 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23,
+ /* HT 40 intolerant mark bit for ACS use */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24,
+ /* Channel temporarily blocked due to noise */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25,
+ /* VHT 160 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26,
+ /* VHT 80+80 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27,
+ /* HE 20 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28,
+ /* HE 40 with extension channel above */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29,
+ /* HE 40 with extension channel below */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30,
+ /* HE 40 intolerant */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31,
+};
+
+/**
+ * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a
+ * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is
+ * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2.
+ */
+enum qca_wlan_vendor_channel_prop_flags_2 {
+ /* HE 40 intolerant mark bit for ACS use */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0,
+ /* HE 80 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1,
+ /* HE 160 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2,
+ /* HE 80+80 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3,
+};
+
+/**
+ * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for
+ * each channel. This is used by
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT.
+ */
+enum qca_wlan_vendor_channel_prop_flags_ext {
+ /* Radar found on channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0,
+ /* DFS required on channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1,
+ /* DFS required on channel for 2nd band of 80+80 */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2,
+ /* If channel has been checked for DFS */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3,
+ /* Excluded in 802.11d */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4,
+ /* Channel Switch Announcement received on this channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5,
+ /* Ad-hoc is not allowed */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6,
+ /* Station only channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7,
+ /* DFS radar history for slave device (STA mode) */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8,
+ /* DFS CAC valid for slave device (STA mode) */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9,
+};
+
+/**
+ * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel
+ * information. These attributes are sent as part of
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following
+ * attributes correspond to a single channel.
+ */
+enum qca_wlan_vendor_external_acs_event_chan_info_attr {
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0,
+
+ /* A bitmask (u32) with flags specified in
+ * enum qca_wlan_vendor_channel_prop_flags.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1,
+ /* A bitmask (u32) with flags specified in
+ * enum qca_wlan_vendor_channel_prop_flags_ext.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2,
+ /* frequency in MHz (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3,
+ /* maximum regulatory transmission power (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4,
+ /* maximum transmission power (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5,
+ /* minimum transmission power (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6,
+ /* regulatory class id (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7,
+ /* maximum antenna gain in (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8,
+ /* VHT segment 0 (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9,
+ /* VHT segment 1 (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10,
+ /* A bitmask (u32) with flags specified in
+ * enum qca_wlan_vendor_channel_prop_flags_2.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST,
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX =
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_pcl: Represents attributes for
+ * preferred channel list (PCL). These attributes are sent as part of
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and
+ * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST.
+ */
+enum qca_wlan_vendor_attr_pcl {
+ QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0,
+
+ /* Channel number (u8) */
+ QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1,
+ /* Channel weightage (u8) */
+ QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2,
+ /* Channel frequency (u32) in MHz */
+ QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3,
+ /* Channel flags (u32)
+ * bit 0 set: channel to be used for GO role,
+ * bit 1 set: channel to be used on CLI role,
+ * bit 2 set: channel must be considered for operating channel
+ * selection & peer chosen operating channel should be
+ * one of the channels with this flag set,
+ * bit 3 set: channel should be excluded in GO negotiation
+ */
+ QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4,
+};
+
+/**
+ * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command
+ * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by
+ * host driver.
+ */
+enum qca_wlan_vendor_attr_external_acs_event {
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0,
+
+ /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason.
+ * This helps ACS module to understand why ACS needs to be started.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1,
+ /* Flag attribute to indicate if driver supports spectral scanning */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2,
+ /* Flag attribute to indicate if 11ac is offloaded to firmware */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3,
+ /* Flag attribute to indicate if driver provides additional channel
+ * capability as part of scan operation */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4,
+ /* Flag attribute to indicate interface status is UP */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5,
+ /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype
+ * values. */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6,
+ /* Channel width (u8). It takes one of enum nl80211_chan_width values.
+ * This is the upper bound of channel width. ACS logic should try to get
+ * a channel with the specified width and if not found, look for lower
+ * values.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7,
+ /* This (u8) will hold values of one of enum nl80211_bands */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8,
+ /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode
+ * values */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9,
+ /* Array of (u32) supported frequency list among which ACS should choose
+ * best frequency.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10,
+ /* Preferred channel list by the driver which will have array of nested
+ * values as per enum qca_wlan_vendor_attr_pcl attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11,
+ /* Array of nested attribute for each channel. It takes attr as defined
+ * in enum qca_wlan_vendor_external_acs_event_chan_info_attr.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12,
+ /* External ACS policy such as PCL mandatory, PCL preferred, etc.
+ * It uses values defined in enum
+ * qca_wlan_vendor_attr_external_acs_policy.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13,
+ /* Reference RF Operating Parameter (RROP) availability information
+ * (u16). It uses values defined in enum
+ * qca_wlan_vendor_attr_rropavail_info.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX =
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
+ * in priority order as decided after ACS operation in userspace.
+ */
+enum qca_wlan_vendor_attr_external_acs_channels {
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0,
+
+ /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1,
+
+ /* Array of nested values for each channel with following attributes:
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2,
+ /* This (u8) will hold values of one of enum nl80211_bands */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3,
+ /* Primary channel (u8) */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4,
+ /* Secondary channel (u8) used for HT 40 MHz channels */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5,
+ /* VHT seg0 channel (u8) */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6,
+ /* VHT seg1 channel (u8) */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7,
+ /* Channel width (u8). Takes one of enum nl80211_chan_width values. */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX =
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1
+};
+
+enum qca_chip_power_save_failure_reason {
+ /* Indicates if the reason for the failure is due to a protocol
+ * layer/module.
+ */
+ QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0,
+ /* Indicates if the reason for the failure is due to a hardware issue.
+ */
+ QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1,
+};
+
+/**
+ * qca_attr_chip_power_save_failure: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite
+ * information leading to the power save failure.
+ */
+enum qca_attr_chip_power_save_failure {
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0,
+ /* Reason to cause the power save failure.
+ * These reasons are represented by
+ * enum qca_chip_power_save_failure_reason.
+ */
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1,
+
+ /* keep last */
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST,
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX =
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various
+ * data types for which the stats have to get collected.
+ */
+enum qca_wlan_vendor_nud_stats_data_pkt_flags {
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0,
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1,
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2,
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3,
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4,
+ /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get
+ * to represent the stats of respective data type.
+ */
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5,
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6,
+ QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7,
+};
+
+enum qca_wlan_vendor_nud_stats_set_data_pkt_info {
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0,
+ /* Represents the data packet type to be monitored (u32).
+ * Host driver tracks the stats corresponding to each data frame
+ * represented by these flags.
+ * These data packets are represented by
+ * enum qca_wlan_vendor_nud_stats_data_pkt_flags
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1,
+ /* Name corresponding to the DNS frame for which the respective DNS
+ * stats have to get monitored (string). Max string length 255.
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2,
+ /* source port on which the respective proto stats have to get
+ * collected (u32).
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3,
+ /* destination port on which the respective proto stats have to get
+ * collected (u32).
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4,
+ /* IPv4 address for which the destined data packets have to be
+ * monitored. (in network byte order), u32.
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5,
+ /* IPv6 address for which the destined data packets have to be
+ * monitored. (in network byte order), 16 bytes array.
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6,
+
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST,
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX =
+ QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite
+ * information to start/stop the NUD statistics collection.
+ */
+enum qca_attr_nud_stats_set {
+ QCA_ATTR_NUD_STATS_SET_INVALID = 0,
+
+ /* Flag to start/stop the NUD statistics collection.
+ * Start - If included, Stop - If not included
+ */
+ QCA_ATTR_NUD_STATS_SET_START = 1,
+ /* IPv4 address of the default gateway (in network byte order), u32 */
+ QCA_ATTR_NUD_STATS_GW_IPV4 = 2,
+ /* Represents the list of data packet types to be monitored.
+ * Host driver tracks the stats corresponding to each data frame
+ * represented by these flags.
+ * These data packets are represented by
+ * enum qca_wlan_vendor_nud_stats_set_data_pkt_info
+ */
+ QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3,
+
+ /* keep last */
+ QCA_ATTR_NUD_STATS_SET_LAST,
+ QCA_ATTR_NUD_STATS_SET_MAX =
+ QCA_ATTR_NUD_STATS_SET_LAST - 1,
+};
+
+enum qca_attr_nud_data_stats {
+ QCA_ATTR_NUD_DATA_STATS_INVALID = 0,
+ /* Data packet type for which the stats are collected (u32).
+ * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags
+ */
+ QCA_ATTR_NUD_STATS_PKT_TYPE = 1,
+ /* Name corresponding to the DNS frame for which the respective DNS
+ * stats are monitored (string). Max string length 255.
+ */
+ QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2,
+ /* source port on which the respective proto stats are collected (u32).
+ */
+ QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3,
+ /* destination port on which the respective proto stats are collected
+ * (u32).
+ */
+ QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4,
+ /* IPv4 address for which the destined data packets have to be
+ * monitored. (in network byte order), u32.
+ */
+ QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5,
+ /* IPv6 address for which the destined data packets have to be
+ * monitored. (in network byte order), 16 bytes array.
+ */
+ QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6,
+ /* Data packet Request count received from netdev (u32). */
+ QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7,
+ /* Data packet Request count sent to lower MAC from upper MAC (u32). */
+ QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8,
+ /* Data packet Request count received by lower MAC from upper MAC
+ * (u32)
+ */
+ QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9,
+ /* Data packet Request count successfully transmitted by the device
+ * (u32)
+ */
+ QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10,
+ /* Data packet Response count received by lower MAC (u32) */
+ QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11,
+ /* Data packet Response count received by upper MAC (u32) */
+ QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12,
+ /* Data packet Response count delivered to netdev (u32) */
+ QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13,
+ /* Data Packet Response count that are dropped out of order (u32) */
+ QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14,
+
+ /* keep last */
+ QCA_ATTR_NUD_DATA_STATS_LAST,
+ QCA_ATTR_NUD_DATA_STATS_MAX =
+ QCA_ATTR_NUD_DATA_STATS_LAST - 1,
+};
+
+/**
+ * qca_attr_nud_stats_get: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite
+ * NUD statistics collected when queried.
+ */
+enum qca_attr_nud_stats_get {
+ QCA_ATTR_NUD_STATS_GET_INVALID = 0,
+ /* ARP Request count from netdev (u32) */
+ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1,
+ /* ARP Request count sent to lower MAC from upper MAC (u32) */
+ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2,
+ /* ARP Request count received by lower MAC from upper MAC (u32) */
+ QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3,
+ /* ARP Request count successfully transmitted by the device (u32) */
+ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4,
+ /* ARP Response count received by lower MAC (u32) */
+ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5,
+ /* ARP Response count received by upper MAC (u32) */
+ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6,
+ /* ARP Response count delivered to netdev (u32) */
+ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7,
+ /* ARP Response count dropped due to out of order reception (u32) */
+ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8,
+ /* Flag indicating if the station's link to the AP is active.
+ * Active Link - If included, Inactive link - If not included
+ */
+ QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9,
+ /* Flag indicating if there is any duplicate address detected (DAD).
+ * Yes - If detected, No - If not detected.
+ */
+ QCA_ATTR_NUD_STATS_IS_DAD = 10,
+ /* List of Data packet types for which the stats are requested.
+ * This list does not carry ARP stats as they are done by the
+ * above attributes. Represented by enum qca_attr_nud_data_stats.
+ */
+ QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11,
+
+ /* keep last */
+ QCA_ATTR_NUD_STATS_GET_LAST,
+ QCA_ATTR_NUD_STATS_GET_MAX =
+ QCA_ATTR_NUD_STATS_GET_LAST - 1,
+};
+
+enum qca_wlan_btm_candidate_status {
+ QCA_STATUS_ACCEPT = 0,
+ QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1,
+ QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2,
+ QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3,
+ QCA_STATUS_REJECT_LOW_RSSI = 4,
+ QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5,
+ QCA_STATUS_REJECT_UNKNOWN = 6,
+};
+
+enum qca_wlan_vendor_attr_btm_candidate_info {
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0,
+
+ /* 6-byte MAC address representing the BSSID of transition candidate */
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1,
+ /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status
+ * returned by the driver. It says whether the BSSID provided in
+ * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by
+ * the driver, if not it specifies the reason for rejection.
+ * Note that the user-space can overwrite the transition reject reason
+ * codes provided by driver based on more information.
+ */
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1,
+};
+
+enum qca_attr_trace_level {
+ QCA_ATTR_TRACE_LEVEL_INVALID = 0,
+ /*
+ * Nested array of the following attributes:
+ * QCA_ATTR_TRACE_LEVEL_MODULE,
+ * QCA_ATTR_TRACE_LEVEL_MASK.
+ */
+ QCA_ATTR_TRACE_LEVEL_PARAM = 1,
+ /*
+ * Specific QCA host driver module. Please refer to the QCA host
+ * driver implementation to get the specific module ID.
+ */
+ QCA_ATTR_TRACE_LEVEL_MODULE = 2,
+ /* Different trace level masks represented in the QCA host driver. */
+ QCA_ATTR_TRACE_LEVEL_MASK = 3,
+
+ /* keep last */
+ QCA_ATTR_TRACE_LEVEL_AFTER_LAST,
+ QCA_ATTR_TRACE_LEVEL_MAX =
+ QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities
+ */
+enum qca_wlan_vendor_attr_get_he_capabilities {
+ QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0,
+ /* Whether HE capabilities is supported
+ * (u8 attribute: 0 = not supported, 1 = supported) */
+ QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1,
+ /* HE PHY capabilities, array of 3 u32 values */
+ QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2,
+ /* HE MAC capabilities (u32 attribute) */
+ QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3,
+ /* HE MCS map (u32 attribute) */
+ QCA_WLAN_VENDOR_ATTR_HE_MCS = 4,
+ /* Number of SS (u32 attribute) */
+ QCA_WLAN_VENDOR_ATTR_NUM_SS = 5,
+ /* RU count (u32 attribute) */
+ QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6,
+ /* PPE threshold data, array of 8 u32 values */
+ QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX =
+ QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters
+ */
+enum qca_wlan_vendor_attr_spectral_scan {
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0,
+ /* Number of times the chip enters spectral scan mode before
+ * deactivating spectral scans. When set to 0, chip will enter spectral
+ * scan mode continuously. u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1,
+ /* Spectral scan period. Period increment resolution is 256*Tclk,
+ * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2,
+ /* Spectral scan priority. u32 attribute. */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3,
+ /* Number of FFT data points to compute. u32 attribute. */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4,
+ /* Enable targeted gain change before starting the spectral scan FFT.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5,
+ /* Restart a queued spectral scan. u32 attribute. */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6,
+ /* Noise floor reference number for the calculation of bin power.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7,
+ /* Disallow spectral scan triggers after TX/RX packets by setting
+ * this delay value to roughly SIFS time period or greater.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8,
+ /* Number of strong bins (inclusive) per sub-channel, below
+ * which a signal is declared a narrow band tone. u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9,
+ /* Specify the threshold over which a bin is declared strong (for
+ * scan bandwidth analysis). u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10,
+ /* Spectral scan report mode. u32 attribute. */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11,
+ /* RSSI report mode, if the ADC RSSI is below
+ * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR,
+ * then FFTs will not trigger, but timestamps and summaries get
+ * reported. u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12,
+ /* ADC RSSI must be greater than or equal to this threshold (signed dB)
+ * to ensure spectral scan reporting with normal error code.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13,
+ /* Format of frequency bin magnitude for spectral scan triggered FFTs:
+ * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)).
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14,
+ /* Format of FFT report to software for spectral scan triggered FFTs.
+ * 0: No FFT report (only spectral scan summary report)
+ * 1: 2-dword summary of metrics for each completed FFT + spectral scan
+ * report
+ * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled
+ * bins (in-band) per FFT + spectral scan summary report
+ * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled
+ * bins (all) per FFT + spectral scan summary report
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15,
+ /* Number of LSBs to shift out in order to scale the FFT bins.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16,
+ /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes
+ * in dBm power. u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17,
+ /* Per chain enable mask to select input ADC for search FFT.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18,
+ /* An unsigned 64-bit integer provided by host driver to identify the
+ * spectral scan request. This attribute is included in the scan
+ * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START
+ * and used as an attribute in
+ * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the
+ * specific scan to be stopped.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19,
+ /* Skip interval for FFT reports. u32 attribute */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20,
+ /* Set to report only one set of FFT results.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21,
+ /* Debug level for spectral module in driver.
+ * 0 : Verbosity level 0
+ * 1 : Verbosity level 1
+ * 2 : Verbosity level 2
+ * 3 : Matched filterID display
+ * 4 : One time dump of FFT report
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22,
+ /* Type of spectral scan request. u32 attribute.
+ * It uses values defined in enum
+ * qca_wlan_vendor_attr_spectral_scan_request_type.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23,
+
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS.
+ */
+enum qca_wlan_vendor_attr_spectral_diag_stats {
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0,
+ /* Number of spectral TLV signature mismatches.
+ * u64 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1,
+ /* Number of spectral phyerror events with insufficient length when
+ * parsing for secondary 80 search FFT report. u64 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2,
+ /* Number of spectral phyerror events without secondary 80
+ * search FFT report. u64 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3,
+ /* Number of spectral phyerror events with vht operation segment 1 id
+ * mismatches in search fft report. u64 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4,
+ /* Number of spectral phyerror events with vht operation segment 2 id
+ * mismatches in search fft report. u64 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5,
+
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX =
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO.
+ */
+enum qca_wlan_vendor_attr_spectral_cap {
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0,
+ /* Flag attribute to indicate phydiag capability */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1,
+ /* Flag attribute to indicate radar detection capability */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2,
+ /* Flag attribute to indicate spectral capability */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3,
+ /* Flag attribute to indicate advanced spectral capability */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4,
+
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX =
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS.
+ */
+enum qca_wlan_vendor_attr_spectral_scan_status {
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0,
+ /* Flag attribute to indicate whether spectral scan is enabled */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1,
+ /* Flag attribute to indicate whether spectral scan is in progress*/
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX =
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for
+ * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the
+ * spectral scan request types.
+ * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to
+ * set the spectral parameters and start scan.
+ * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to
+ * only set the spectral parameters.
+ * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to
+ * only start the spectral scan.
+ */
+enum qca_wlan_vendor_attr_spectral_scan_request_type {
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG,
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN,
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG,
+};
+
+enum qca_wlan_vendor_tos {
+ QCA_WLAN_VENDOR_TOS_BK = 0,
+ QCA_WLAN_VENDOR_TOS_BE = 1,
+ QCA_WLAN_VENDOR_TOS_VI = 2,
+ QCA_WLAN_VENDOR_TOS_VO = 3,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS.
+ */
+enum qca_wlan_vendor_attr_active_tos {
+ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0,
+ /* Type Of Service - Represented by qca_wlan_vendor_tos */
+ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1,
+ /* Flag attribute representing the start (attribute included) or stop
+ * (attribute not included) of the respective TOS.
+ */
+ QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2,
+};
+
+enum qca_wlan_vendor_hang_reason {
+ /* Unspecified reason */
+ QCA_WLAN_HANG_REASON_UNSPECIFIED = 0,
+ /* No Map for the MAC entry for the received frame */
+ QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1,
+ /* Peer deletion timeout happened */
+ QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2,
+ /* Peer unmap timeout */
+ QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3,
+ /* Scan request timed out */
+ QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4,
+ /* Consecutive Scan attempt failures */
+ QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5,
+ /* Unable to get the message buffer */
+ QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6,
+ /* Current command processing is timedout */
+ QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7,
+ /* Timeout for an ACK from FW for suspend request */
+ QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8,
+ /* Timeout for an ACK from FW for resume request */
+ QCA_WLAN_HANG_RESUME_TIMEOUT = 9,
+ /* Transmission timeout for consecutive data frames */
+ QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10,
+ /* Timeout for the TX completion status of data frame */
+ QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11,
+ /* DXE failure for TX/RX, DXE resource unavailability */
+ QCA_WLAN_HANG_DXE_FAILURE = 12,
+ /* WMI pending commands exceed the maximum count */
+ QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_hang - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_HANG.
+ */
+enum qca_wlan_vendor_attr_hang {
+ QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0,
+ /* Reason for the hang - u32 attribute with a value from enum
+ * qca_wlan_vendor_hang_reason.
+ */
+ QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1,
+
+ QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HANG_MAX =
+ QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_flush_pending - Attributes for
+ * flushing pending traffic in firmware.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address.
+ * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending
+ * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK,
+ * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to
+ * flush packets with access category.
+ */
+enum qca_wlan_vendor_attr_flush_pending {
+ QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1,
+ QCA_WLAN_VENDOR_ATTR_AC = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX =
+ QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative
+ * RF Operating Parameter (RROP) information is available, and if so, at which
+ * point in the application-driver interaction sequence it can be retrieved by
+ * the application from the driver. This point may vary by architecture and
+ * other factors. This is a u16 value.
+ */
+enum qca_wlan_vendor_attr_rropavail_info {
+ /* RROP information is unavailable. */
+ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE,
+ /* RROP information is available and the application can retrieve the
+ * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS
+ * event from the driver.
+ */
+ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START,
+ /* RROP information is available only after a vendor specific scan
+ * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has
+ * successfully completed. The application can retrieve the information
+ * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from
+ * the driver.
+ */
+ QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific
+ * Representative RF Operating Parameter (RROP) information. It is sent for the
+ * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is
+ * intended for use by external Auto Channel Selection applications. It provides
+ * guidance values for some RF parameters that are used by the system during
+ * operation. These values could vary by channel, band, radio, and so on.
+ */
+enum qca_wlan_vendor_attr_rrop_info {
+ QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0,
+
+ /* Representative Tx Power List (RTPL) which has an array of nested
+ * values as per attributes in enum qca_wlan_vendor_attr_rtplinst.
+ */
+ QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1,
+
+ QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list
+ * entry instances in the Representative Tx Power List (RTPL). It provides
+ * simplified power values intended for helping external Auto channel Selection
+ * applications compare potential Tx power performance between channels, other
+ * operating conditions remaining identical. These values are not necessarily
+ * the actual Tx power values that will be used by the system. They are also not
+ * necessarily the max or average values that will be used. Instead, they are
+ * relative, summarized keys for algorithmic use computed by the driver or
+ * underlying firmware considering a number of vendor specific factors.
+ */
+enum qca_wlan_vendor_attr_rtplinst {
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0,
+
+ /* Primary channel number (u8) */
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1,
+ /* Representative Tx power in dBm (s32) with emphasis on throughput. */
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2,
+ /* Representative Tx power in dBm (s32) with emphasis on range. */
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3,
+
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX =
+ QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_config_latency_level - Level for
+ * wlan latency module.
+ *
+ * There will be various of Wi-Fi functionality like scan/roaming/adaptive
+ * power saving which would causing data exchange out of service, this
+ * would be a big impact on latency. For latency sensitive applications over
+ * Wi-Fi are intolerant to such operations and thus would configure them
+ * to meet their respective needs. It is well understood by such applications
+ * that altering the default behavior would degrade the Wi-Fi functionality
+ * w.r.t the above pointed WLAN operations.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL:
+ * Default WLAN operation level which throughput orientated.
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE:
+ * Use moderate level to improve latency by limit scan duration.
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW:
+ * Use low latency level to benifit application like concurrent
+ * downloading or video streaming via constraint scan/adaptive PS.
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW:
+ * Use ultra low latency level to benefit for gaming/voice
+ * application via constraint scan/roaming/adaptive PS.
+ */
+enum qca_wlan_vendor_attr_config_latency_level {
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX =
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
+ */
+enum qca_wlan_vendor_attr_mac {
+ QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0,
+
+ /* MAC mode info list which has an array of nested values as
+ * per attributes in enum qca_wlan_vendor_attr_mac_mode_info.
+ */
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_MAC_MAX =
+ QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected
+ * Wi-Fi netdev interface on a respective MAC.
+ * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO.
+ */
+enum qca_wlan_vendor_attr_mac_iface_info {
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0,
+ /* Wi-Fi netdev's interface index (u32) */
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1,
+ /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information.
+ * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the
+ * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO.
+ */
+enum qca_wlan_vendor_attr_mac_info {
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0,
+ /* Hardware MAC ID associated for the MAC (u32) */
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1,
+ /* Band supported by the MAC at a given point.
+ * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum
+ * nl80211_band.
+ */
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2,
+ /* Refers to list of WLAN netdev interfaces associated with this MAC.
+ * Represented by enum qca_wlan_vendor_attr_mac_iface_info.
+ */
+ QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET.
+ */
+enum qca_wlan_vendor_attr_get_logger_features {
+ QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0,
+ /* Unsigned 32-bit enum value of wifi_logger_supported_features */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LOGGER_MAX =
+ QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1,
+};
+
+/**
+ * enum wifi_logger_supported_features - Values for supported logger features
+ */
+enum wifi_logger_supported_features {
+ WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)),
+ WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)),
+ WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)),
+ WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)),
+ WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)),
+ WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)),
+ WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)),
+ WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)),
+ WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)),
+};
+
+/**
+ * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get
+ * capabilities features
+ */
+enum qca_wlan_tdls_caps_features_supported
+{
+ WIFI_TDLS_SUPPORT = (1 << (0)),
+ WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)),
+ WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2))
+};
+
+/**
+ * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES.
+ */
+enum qca_wlan_vendor_attr_tdls_get_capabilities
+{
+ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0,
+ /* Indicates the max concurrent sessions */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS,
+ /* Indicates the support for features */
+ /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported
+ */
+ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX =
+ QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_offloaded_packets_sending_control - Offload packets control
+ * command used as value for the attribute
+ * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL.
+ */
+enum qca_wlan_offloaded_packets_sending_control
+{
+ QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0,
+ QCA_WLAN_OFFLOADED_PACKETS_SENDING_START,
+ QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP
+};
+
+/**
+ * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS.
+ */
+enum qca_wlan_vendor_attr_offloaded_packets {
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0,
+ /* Takes valid value from the enum
+ * qca_wlan_offloaded_packets_sending_control
+ * Unsigned 32-bit value
+ */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID,
+ /* array of u8 len: Max packet size */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA,
+ /* 6-byte MAC address used to represent source MAC address */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR,
+ /* 6-byte MAC address used to represent destination MAC address */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR,
+ /* Unsigned 32-bit value, in milli seconds */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX =
+ QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values
+ * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL.
+ */
+enum qca_wlan_rssi_monitoring_control {
+ QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0,
+ QCA_WLAN_RSSI_MONITORING_START,
+ QCA_WLAN_RSSI_MONITORING_STOP,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI.
+ */
+enum qca_wlan_vendor_attr_rssi_monitoring {
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0,
+ /* Takes valid value from the enum
+ * qca_wlan_rssi_monitoring_control
+ * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control
+ */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID,
+ /* Signed 8-bit value in dBm */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI,
+ /* Signed 8-bit value in dBm */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI,
+ /* attributes to be used/received in callback */
+ /* 6-byte MAC address used to represent current BSSID MAC address */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID,
+ /* Signed 8-bit value indicating the current RSSI */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX =
+ QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_NDP.
+ */
+enum qca_wlan_vendor_attr_ndp_params {
+ QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0,
+ /* Unsigned 32-bit value
+ * enum of sub commands values in qca_wlan_ndp_sub_cmd
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD,
+ /* Unsigned 16-bit value */
+ QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID,
+ /* NL attributes for data used NDP SUB cmds */
+ /* Unsigned 32-bit value indicating a service info */
+ QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID,
+ /* Unsigned 32-bit value; channel frequency in MHz */
+ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL,
+ /* Interface Discovery MAC address. An array of 6 Unsigned int8 */
+ QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR,
+ /* Interface name on which NDP is being created */
+ QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR,
+ /* Unsigned 32-bit value for security */
+ /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */
+ QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY,
+ /* Unsigned 32-bit value for QoS */
+ QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS,
+ /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */
+ QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO,
+ /* Unsigned 32-bit value for NDP instance Id */
+ QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID,
+ /* Array of instance Ids */
+ QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY,
+ /* Unsigned 32-bit value for initiator/responder NDP response code
+ * accept/reject */
+ QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE,
+ /* NDI MAC address. An array of 6 Unsigned int8 */
+ QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR,
+ /* Unsigned 32-bit value errors types returned by driver
+ * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
+ * NanStatusType includes these values.
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE,
+ /* Unsigned 32-bit value error values returned by driver
+ * The nan_i.h in AOSP project platform/hardware/qcom/wlan
+ * NanInternalStatusType includes these values.
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE,
+ /* Unsigned 32-bit value for Channel setup configuration
+ * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy
+ * NanDataPathChannelCfg includes these values.
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG,
+ /* Unsigned 32-bit value for Cipher Suite Shared Key Type */
+ QCA_WLAN_VENDOR_ATTR_NDP_CSID,
+ /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */
+ QCA_WLAN_VENDOR_ATTR_NDP_PMK,
+ /* Security Context Identifier that contains the PMKID
+ * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_SCID,
+ /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */
+ QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE,
+ /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */
+ QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME,
+ /* Unsigned 32-bit bitmap indicating schedule update
+ * BIT_0: NSS Update
+ * BIT_1: Channel list update
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON,
+ /* Unsigned 32-bit value for NSS */
+ QCA_WLAN_VENDOR_ATTR_NDP_NSS,
+ /* Unsigned 32-bit value for NUMBER NDP CHANNEL */
+ QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS,
+ /* Unsigned 32-bit value for CHANNEL BANDWIDTH
+ * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz
+ */
+ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH,
+ /* Array of channel/band width */
+ QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX =
+ QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1,
+};
+
+enum qca_wlan_ndp_sub_cmd {
+ QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0,
+ /* Command to create a NAN data path interface */
+ QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1,
+ /* Command to delete a NAN data path interface */
+ QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2,
+ /* Command to initiate a NAN data path session */
+ QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3,
+ /* Command to notify if the NAN data path session was sent */
+ QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4,
+ /* Command to respond to NAN data path session */
+ QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5,
+ /* Command to notify on the responder about the response */
+ QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6,
+ /* Command to initiate a NAN data path end */
+ QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7,
+ /* Command to notify the if end request was sent */
+ QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8,
+ /* Command to notify the peer about the end request */
+ QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9,
+ /* Command to confirm the NAN data path session is complete */
+ QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10,
+ /* Command to indicate the peer about the end request being received */
+ QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11,
+ /* Command to indicate the peer of schedule update */
+ QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12
+};
+
+/**
+ * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD.
+ */
+enum qca_wlan_vendor_attr_nd_offload {
+ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0,
+ /* Flag to set Neighbour Discovery offload */
+ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG,
+ /* Keep last */
+ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX =
+ QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1,
+};
+
+/**
+ * enum packet_filter_sub_cmd - Packet filter sub command
+ */
+enum packet_filter_sub_cmd {
+ QCA_WLAN_SET_PACKET_FILTER = 1,
+ QCA_WLAN_GET_PACKET_FILTER = 2,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by
+ * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER.
+ */
+enum qca_wlan_vendor_attr_packet_filter {
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0,
+ /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD,
+ /* Unsigned 32-bit value indicating the packet filter version */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION,
+ /* Unsigned 32-bit value indicating the packet filter id */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID,
+ /* Unsigned 32-bit value indicating the packet filter size */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE,
+ /* Unsigned 32-bit value indicating the packet filter current offset */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET,
+ /* Unsigned 32-bit value indicating length of BPF instructions */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX =
+ QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command
+ * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE.
+ */
+enum qca_wlan_vendor_drv_info {
+ QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0,
+ /* Maximum Message size info between firmware & HOST
+ * Unsigned 32-bit value
+ */
+ QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor
+ * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS.
+ */
+enum qca_wlan_vendor_attr_wake_stats {
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0,
+ /* Unsigned 32-bit value indicating the total count of wake event */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE,
+ /* Array of individual wake count, each index representing wake reason
+ */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR,
+ /* Unsigned 32-bit value representing wake count array */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ,
+ /* Unsigned 32-bit total wake count value of driver/fw */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE,
+ /* Array of wake stats of driver/fw */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR,
+ /* Unsigned 32-bit total wake count value of driver/fw */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ,
+ /* Unsigned 32-bit total wake count value of packets received */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE,
+ /* Unsigned 32-bit wake count value unicast packets received */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT,
+ /* Unsigned 32-bit wake count value multicast packets received */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT,
+ /* Unsigned 32-bit wake count value broadcast packets received */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT,
+ /* Unsigned 32-bit wake count value of ICMP packets */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT,
+ /* Unsigned 32-bit wake count value of ICMP6 packets */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT,
+ /* Unsigned 32-bit value ICMP6 router advertisement */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA,
+ /* Unsigned 32-bit value ICMP6 neighbor advertisement */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA,
+ /* Unsigned 32-bit value ICMP6 neighbor solicitation */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS,
+ /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT,
+ /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT,
+ /* Unsigned 32-bit wake count value of receive side multicast */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT,
+ /* Unsigned 32-bit wake count value of a given RSSI breach */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT,
+ /* Unsigned 32-bit wake count value of low RSSI */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT,
+ /* Unsigned 32-bit value GSCAN count */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT,
+ /* Unsigned 32-bit value PNO complete count */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT,
+ /* Unsigned 32-bit value PNO match count */
+ QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT,
+ /* keep last */
+ QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST,
+ QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX =
+ QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set
+ * cmd value. Used for NL attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
+ */
+enum qca_wlan_vendor_attr_thermal_cmd {
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0,
+ /* The value of command, driver will implement different operations
+ * according to this value. It uses values defined in
+ * enum qca_wlan_vendor_attr_thermal_cmd_type.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX =
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1
+};
+
+/**
+ * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for
+ * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the
+ * thermal command types sent to driver.
+ * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to
+ * get thermal shutdown configuration parameters for display. Parameters
+ * responded from driver are defined in
+ * enum qca_wlan_vendor_attr_get_thermal_params_rsp.
+ * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to
+ * get temperature. Host should respond with a temperature data. It is defined
+ * in enum qca_wlan_vendor_attr_thermal_get_temperature.
+ * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal
+ * suspend action.
+ * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal
+ * resume action.
+ */
+enum qca_wlan_vendor_attr_thermal_cmd_type {
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes
+ * to get chip temperature by user.
+ * enum values are used for NL attributes for data used by
+ * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used
+ * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
+ */
+enum qca_wlan_vendor_attr_thermal_get_temperature {
+ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0,
+ /* Temperature value (degree Celsius) from driver.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX =
+ QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes
+ * to get configuration parameters of thermal shutdown feature. Enum values are
+ * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data
+ * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command.
+ */
+enum qca_wlan_vendor_attr_get_thermal_params_rsp {
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0,
+ /* Indicate if the thermal shutdown feature is enabled.
+ * NLA_FLAG attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN,
+ /* Indicate if the auto mode is enabled.
+ * Enable: Driver triggers the suspend/resume action.
+ * Disable: User space triggers the suspend/resume action.
+ * NLA_FLAG attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN,
+ /* Thermal resume threshold (degree Celsius). Issue the resume command
+ * if the temperature value is lower than this threshold.
+ * u16 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH,
+ /* Thermal warning threshold (degree Celsius). FW reports temperature
+ * to driver if it's higher than this threshold.
+ * u16 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH,
+ /* Thermal suspend threshold (degree Celsius). Issue the suspend command
+ * if the temperature value is higher than this threshold.
+ * u16 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH,
+ /* FW reports temperature data periodically at this interval (ms).
+ * u16 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX =
+ QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to
+ * report thermal events from driver to user space.
+ * enum values are used for NL attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command.
+ */
+enum qca_wlan_vendor_attr_thermal_event {
+ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0,
+ /* Temperature value (degree Celsius) from driver.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE,
+ /* Indication of resume completion from power save mode.
+ * NLA_FLAG attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX =
+ QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */
projects / thirdparty / hostap.git / blobdiff