/*
* Driver interface definition
- * Copyright (c) 2003-2015, Jouni Malinen <j@w1.fi>
+ * Copyright (c) 2003-2017, Jouni Malinen <j@w1.fi>
*
* This software may be distributed under the terms of the BSD license.
* See README for more details.
#include "common/defs.h"
#include "common/ieee802_11_defs.h"
+#include "common/wpa_common.h"
#ifdef CONFIG_MACSEC
#include "pae/ieee802_1x_kay.h"
#endif /* CONFIG_MACSEC */
/* Filter unicast IP packets encrypted using the GTK */
#define WPA_DATA_FRAME_FILTER_FLAG_GTK BIT(2)
+#define HOSTAPD_DFS_REGION_FCC 1
+#define HOSTAPD_DFS_REGION_ETSI 2
+#define HOSTAPD_DFS_REGION_JP 3
+
/**
* enum reg_change_initiator - Regulatory change initiator
*/
unsigned int dfs_cac_ms;
};
+#define HE_MAX_NUM_SS 8
+#define HE_MAX_PHY_CAPAB_SIZE 3
+
+/**
+ * struct he_ppe_threshold - IEEE 802.11ax HE PPE Threshold
+ */
+struct he_ppe_threshold {
+ u32 numss_m1;
+ u32 ru_count;
+ u32 ppet16_ppet8_ru3_ru0[HE_MAX_NUM_SS];
+};
+
+/**
+ * struct he_capabilities - IEEE 802.11ax HE capabilities
+ */
+struct he_capabilities {
+ u8 he_supported;
+ u32 phy_cap[HE_MAX_PHY_CAPAB_SIZE];
+ u32 mac_cap;
+ u32 mcs;
+ struct he_ppe_threshold ppet;
+};
+
#define HOSTAPD_MODE_FLAG_HT_INFO_KNOWN BIT(0)
#define HOSTAPD_MODE_FLAG_VHT_INFO_KNOWN BIT(1)
u8 vht_mcs_set[8];
unsigned int flags; /* HOSTAPD_MODE_FLAG_* */
+
+ /**
+ * he_capab - HE (IEEE 802.11ax) capabilities
+ */
+ struct he_capabilities he_capab;
};
* @est_throughput: Estimated throughput in kbps (this is calculated during
* scan result processing if left zero by the driver wrapper)
* @snr: Signal-to-noise ratio in dB (calculated during scan result processing)
+ * @parent_tsf: Time when the Beacon/Probe Response frame was received in terms
+ * of TSF of the BSS specified by %tsf_bssid.
+ * @tsf_bssid: The BSS that %parent_tsf TSF time refers to.
* @ie_len: length of the following IE field in octets
* @beacon_ie_len: length of the following Beacon IE field in octets
*
unsigned int age;
unsigned int est_throughput;
int snr;
+ u64 parent_tsf;
+ u8 tsf_bssid[ETH_ALEN];
size_t ie_len;
size_t beacon_ie_len;
/* Followed by ie_len + beacon_ie_len octets of IE data */
*/
unsigned int sched_scan_plans_num;
+ /**
+ * sched_scan_start_delay - Delay to use before starting the first scan
+ *
+ * Delay (in seconds) before scheduling first scan plan cycle. The
+ * driver may ignore this parameter and start immediately (or at any
+ * other time), if this feature is not supported.
+ */
+ u32 sched_scan_start_delay;
+
/**
* bssid - Specific BSSID to scan for
*
*/
const u8 *bssid;
+ /**
+ * scan_cookie - Unique identification representing the scan request
+ *
+ * This scan_cookie carries a unique identification representing the
+ * scan request if the host driver/kernel supports concurrent scan
+ * requests. This cookie is returned from the corresponding driver
+ * interface.
+ *
+ * Note: Unlike other parameters in this structure, scan_cookie is used
+ * only to return information instead of setting parameters for the
+ * scan.
+ */
+ u64 scan_cookie;
+
+ /**
+ * duration - Dwell time on each channel
+ *
+ * This optional parameter can be used to set the dwell time on each
+ * channel. In TUs.
+ */
+ u16 duration;
+
+ /**
+ * duration_mandatory - Whether the specified duration is mandatory
+ *
+ * If this is set, the duration specified by the %duration field is
+ * mandatory (and the driver should reject the scan request if it is
+ * unable to comply with the specified duration), otherwise it is the
+ * maximum duration and the actual duration may be shorter.
+ */
+ unsigned int duration_mandatory:1;
+
+ /**
+ * relative_rssi_set - Whether relative RSSI parameters are set
+ */
+ unsigned int relative_rssi_set:1;
+
+ /**
+ * relative_rssi - Relative RSSI for reporting better BSSs
+ *
+ * Amount of RSSI by which a BSS should be better than the current
+ * connected BSS to report the new BSS to user space.
+ */
+ s8 relative_rssi;
+
+ /**
+ * relative_adjust_band - Band to which RSSI should be adjusted
+ *
+ * The relative_adjust_rssi should be added to the band specified
+ * by relative_adjust_band.
+ */
+ enum set_band relative_adjust_band;
+
+ /**
+ * relative_adjust_rssi - RSSI to be added to relative_adjust_band
+ *
+ * An amount of relative_band_rssi should be added to the BSSs that
+ * belong to the band specified by relative_adjust_band while comparing
+ * with other bands for BSS reporting.
+ */
+ s8 relative_adjust_rssi;
+
/*
* NOTE: Whenever adding new parameters here, please make sure
* wpa_scan_clone_params() and wpa_scan_free_params() get updated with
int bandwidth;
};
+/**
+ * struct wpa_driver_sta_auth_params - Authentication parameters
+ * Data for struct wpa_driver_ops::sta_auth().
+ */
+struct wpa_driver_sta_auth_params {
+
+ /**
+ * own_addr - Source address and BSSID for authentication frame
+ */
+ const u8 *own_addr;
+
+ /**
+ * addr - MAC address of the station to associate
+ */
+ const u8 *addr;
+
+ /**
+ * seq - authentication sequence number
+ */
+ u16 seq;
+
+ /**
+ * status - authentication response status code
+ */
+ u16 status;
+
+ /**
+ * ie - authentication frame ie buffer
+ */
+ const u8 *ie;
+
+ /**
+ * len - ie buffer length
+ */
+ size_t len;
+
+ /**
+ * fils_auth - Indicates whether FILS authentication is being performed
+ */
+ int fils_auth;
+
+ /**
+ * fils_anonce - ANonce (required for FILS)
+ */
+ u8 fils_anonce[WPA_NONCE_LEN];
+
+ /**
+ * fils_snonce - SNonce (required for FILS)
+ */
+ u8 fils_snonce[WPA_NONCE_LEN];
+
+ /**
+ * fils_kek - key for encryption (required for FILS)
+ */
+ u8 fils_kek[WPA_KEK_MAX_LEN];
+
+ /**
+ * fils_kek_len - Length of the fils_kek in octets (required for FILS)
+ */
+ size_t fils_kek_len;
+};
+
/**
* struct wpa_driver_associate_params - Association parameters
* Data for struct wpa_driver_ops::associate().
* WPA information element to be included in (Re)Association
* Request (including information element id and length). Use
* of this WPA IE is optional. If the driver generates the WPA
- * IE, it can use pairwise_suite, group_suite, and
+ * IE, it can use pairwise_suite, group_suite, group_mgmt_suite, and
* key_mgmt_suite to select proper algorithms. In this case,
* the driver has to notify wpa_supplicant about the used WPA
* IE by generating an event that the interface code will
*/
unsigned int group_suite;
+ /**
+ * mgmt_group_suite - Selected group management cipher suite (WPA_CIPHER_*)
+ *
+ * This is usually ignored if @wpa_ie is used.
+ */
+ unsigned int mgmt_group_suite;
+
/**
* key_mgmt_suite - Selected key management suite (WPA_KEY_MGMT_*)
*
*/
enum mfp_options mgmt_frame_protection;
- /**
- * ft_ies - IEEE 802.11r / FT information elements
- * If the supplicant is using IEEE 802.11r (FT) and has the needed keys
- * for fast transition, this parameter is set to include the IEs that
- * are to be sent in the next FT Authentication Request message.
- * update_ft_ies() handler is called to update the IEs for further
- * FT messages in the sequence.
- *
- * The driver should use these IEs only if the target AP is advertising
- * the same mobility domain as the one included in the MDIE here.
- *
- * In ap_scan=2 mode, the driver can use these IEs when moving to a new
- * AP after the initial association. These IEs can only be used if the
- * target AP is advertising support for FT and is using the same MDIE
- * and SSID as the current AP.
- *
- * The driver is responsible for reporting the FT IEs received from the
- * AP's response using wpa_supplicant_event() with EVENT_FT_RESPONSE
- * type. update_ft_ies() handler will then be called with the FT IEs to
- * include in the next frame in the authentication sequence.
- */
- const u8 *ft_ies;
-
- /**
- * ft_ies_len - Length of ft_ies in bytes
- */
- size_t ft_ies_len;
-
- /**
- * ft_md - FT Mobility domain (6 octets) (also included inside ft_ies)
- *
- * This value is provided to allow the driver interface easier access
- * to the current mobility domain. This value is set to %NULL if no
- * mobility domain is currently active.
- */
- const u8 *ft_md;
-
/**
* passphrase - RSN passphrase for PSK
*
* fils_nonces_len: Length of fils_nonce in bytes
*/
size_t fils_nonces_len;
+
+ /**
+ * fils_erp_username - Username part of keyName-NAI
+ */
+ const u8 *fils_erp_username;
+
+ /**
+ * fils_erp_username_len - Length of fils_erp_username in bytes
+ */
+ size_t fils_erp_username_len;
+
+ /**
+ * fils_erp_realm - Realm/domain name to use in FILS ERP
+ */
+ const u8 *fils_erp_realm;
+
+ /**
+ * fils_erp_realm_len - Length of fils_erp_realm in bytes
+ */
+ size_t fils_erp_realm_len;
+
+ /**
+ * fils_erp_next_seq_num - The next sequence number to use in FILS ERP
+ * messages
+ */
+ u16 fils_erp_next_seq_num;
+
+ /**
+ * fils_erp_rrk - Re-authentication root key (rRK) for the keyName-NAI
+ * specified by fils_erp_username@fils_erp_realm.
+ */
+ const u8 *fils_erp_rrk;
+
+ /**
+ * fils_erp_rrk_len - Length of fils_erp_rrk in bytes
+ */
+ size_t fils_erp_rrk_len;
};
enum hide_ssid {
*/
int *basic_rates;
+ /**
+ * beacon_rate: Beacon frame data rate
+ *
+ * This parameter can be used to set a specific Beacon frame data rate
+ * for the BSS. The interpretation of this value depends on the
+ * rate_type (legacy: in 100 kbps units, HT: HT-MCS, VHT: VHT-MCS). If
+ * beacon_rate == 0 and rate_type == 0 (BEACON_RATE_LEGACY), the default
+ * Beacon frame data rate is used.
+ */
+ unsigned int beacon_rate;
+
+ /**
+ * beacon_rate_type: Beacon data rate type (legacy/HT/VHT)
+ */
+ enum beacon_rate_type rate_type;
+
/**
* proberesp - Probe Response template
*
* infrastructure BSS. Valid only for DMG network.
*/
int pbss;
+
+ /**
+ * multicast_to_unicast - Whether to use multicast_to_unicast
+ *
+ * If this is non-zero, the AP is requested to perform multicast to
+ * unicast conversion for ARP, IPv4, and IPv6 frames (possibly within
+ * 802.1Q). If enabled, such frames are to be sent to each station
+ * separately, with the DA replaced by their own MAC address rather
+ * than the group address.
+ *
+ * Note that this may break certain expectations of the receiver, such
+ * as the ability to drop unicast IP packets received within multicast
+ * L2 frames, or the ability to not send ICMP destination unreachable
+ * messages for packets received in L2 multicast (which is required,
+ * but the receiver can't tell the difference if this new option is
+ * enabled.)
+ *
+ * This also doesn't implement the 802.11 DMS (directed multicast
+ * service).
+ */
+ int multicast_to_unicast;
};
struct wpa_driver_mesh_bss_params {
#define WPA_DRIVER_MESH_CONF_FLAG_PEER_LINK_TIMEOUT 0x00000002
#define WPA_DRIVER_MESH_CONF_FLAG_MAX_PEER_LINKS 0x00000004
#define WPA_DRIVER_MESH_CONF_FLAG_HT_OP_MODE 0x00000008
+#define WPA_DRIVER_MESH_CONF_FLAG_RSSI_THRESHOLD 0x00000010
/*
* TODO: Other mesh configuration parameters would go here.
* See NL80211_MESHCONF_* for all the mesh config parameters.
int auto_plinks;
int peer_link_timeout;
int max_peer_links;
+ int rssi_threshold;
u16 ht_opmode;
};
#define WPA_DRIVER_CAPA_KEY_MGMT_WAPI_PSK 0x00000080
#define WPA_DRIVER_CAPA_KEY_MGMT_SUITE_B 0x00000100
#define WPA_DRIVER_CAPA_KEY_MGMT_SUITE_B_192 0x00000200
+#define WPA_DRIVER_CAPA_KEY_MGMT_OWE 0x00000400
+#define WPA_DRIVER_CAPA_KEY_MGMT_DPP 0x00000800
+#define WPA_DRIVER_CAPA_KEY_MGMT_FILS_SHA256 0x00001000
+#define WPA_DRIVER_CAPA_KEY_MGMT_FILS_SHA384 0x00002000
+#define WPA_DRIVER_CAPA_KEY_MGMT_FT_FILS_SHA256 0x00004000
+#define WPA_DRIVER_CAPA_KEY_MGMT_FT_FILS_SHA384 0x00008000
/** Bitfield of supported key management suites */
unsigned int key_mgmt;
#define WPA_DRIVER_FLAGS_FULL_AP_CLIENT_STATE 0x0000010000000000ULL
/** Driver supports P2P Listen offload */
#define WPA_DRIVER_FLAGS_P2P_LISTEN_OFFLOAD 0x0000020000000000ULL
+/** Driver supports FILS */
+#define WPA_DRIVER_FLAGS_SUPPORT_FILS 0x0000040000000000ULL
+/** Driver supports Beacon frame TX rate configuration (legacy rates) */
+#define WPA_DRIVER_FLAGS_BEACON_RATE_LEGACY 0x0000080000000000ULL
+/** Driver supports Beacon frame TX rate configuration (HT rates) */
+#define WPA_DRIVER_FLAGS_BEACON_RATE_HT 0x0000100000000000ULL
+/** Driver supports Beacon frame TX rate configuration (VHT rates) */
+#define WPA_DRIVER_FLAGS_BEACON_RATE_VHT 0x0000200000000000ULL
+/** Driver supports mgmt_tx with random TX address in non-connected state */
+#define WPA_DRIVER_FLAGS_MGMT_TX_RANDOM_TA 0x0000400000000000ULL
+/** Driver supports mgmt_tx with random TX addr in connected state */
+#define WPA_DRIVER_FLAGS_MGMT_TX_RANDOM_TA_CONNECTED 0x0000800000000000ULL
+/** Driver supports better BSS reporting with sched_scan in connected mode */
+#define WPA_DRIVER_FLAGS_SCHED_SCAN_RELATIVE_RSSI 0x0001000000000000ULL
+/** Driver supports HE capabilities */
+#define WPA_DRIVER_FLAGS_HE_CAPABILITIES 0x0002000000000000ULL
+/** Driver supports FILS shared key offload */
+#define WPA_DRIVER_FLAGS_FILS_SK_OFFLOAD 0x0004000000000000ULL
+/** Driver supports all OCE STA specific mandatory features */
+#define WPA_DRIVER_FLAGS_OCE_STA 0x0008000000000000ULL
+/** Driver supports all OCE AP specific mandatory features */
+#define WPA_DRIVER_FLAGS_OCE_AP 0x0010000000000000ULL
+/**
+ * Driver supports all OCE STA-CFON specific mandatory features only.
+ * If a driver sets this bit but not the %WPA_DRIVER_FLAGS_OCE_AP, the
+ * userspace shall assume that this driver may not support all OCE AP
+ * functionality but can support only OCE STA-CFON functionality.
+ */
+#define WPA_DRIVER_FLAGS_OCE_STA_CFON 0x0020000000000000ULL
+/** Driver supports MFP-optional in the connect command */
+#define WPA_DRIVER_FLAGS_MFP_OPTIONAL 0x0040000000000000ULL
u64 flags;
#define FULL_AP_CLIENT_STATE_SUPP(drv_flags) \
*/
#define WPA_DRIVER_FLAGS_SUPPORT_RRM 0x00000010
+/** Driver supports setting the scan dwell time */
+#define WPA_DRIVER_FLAGS_SUPPORT_SET_SCAN_DWELL 0x00000020
+/** Driver supports Beacon Report Measurement */
+#define WPA_DRIVER_FLAGS_SUPPORT_BEACON_REPORT 0x00000040
+
u32 rrm_flags;
/* Driver concurrency capabilities */
struct hostapd_data;
+#define STA_DRV_DATA_TX_MCS BIT(0)
+#define STA_DRV_DATA_RX_MCS BIT(1)
+#define STA_DRV_DATA_TX_VHT_MCS BIT(2)
+#define STA_DRV_DATA_RX_VHT_MCS BIT(3)
+#define STA_DRV_DATA_TX_VHT_NSS BIT(4)
+#define STA_DRV_DATA_RX_VHT_NSS BIT(5)
+#define STA_DRV_DATA_TX_SHORT_GI BIT(6)
+#define STA_DRV_DATA_RX_SHORT_GI BIT(7)
+#define STA_DRV_DATA_LAST_ACK_RSSI BIT(8)
+
struct hostap_sta_driver_data {
unsigned long rx_packets, tx_packets;
unsigned long long rx_bytes, tx_bytes;
int bytes_64bit; /* whether 64-bit byte counters are supported */
unsigned long current_tx_rate;
+ unsigned long current_rx_rate;
unsigned long inactive_msec;
- unsigned long flags;
+ unsigned long flags; /* bitfield of STA_DRV_DATA_* */
unsigned long num_ps_buf_frames;
unsigned long tx_retry_failed;
unsigned long tx_retry_count;
- int last_rssi;
- int last_ack_rssi;
+ s8 last_ack_rssi;
+ s8 signal;
+ u8 rx_vhtmcs;
+ u8 tx_vhtmcs;
+ u8 rx_mcs;
+ u8 tx_mcs;
+ u8 rx_vht_nss;
+ u8 tx_vht_nss;
};
struct hostapd_sta_add_params {
WNM_SLEEP_TFS_IE_DEL /* AP delete the TFS IE */
};
+/* enum smps_mode - SMPS mode definitions */
+enum smps_mode {
+ SMPS_AUTOMATIC,
+ SMPS_OFF,
+ SMPS_DYNAMIC,
+ SMPS_STATIC,
+
+ /* Keep last */
+ SMPS_INVALID,
+};
+
/* enum chan_width - Channel width definitions */
enum chan_width {
CHAN_WIDTH_20_NOHT,
const int *freq_list;
};
+struct wpa_bss_trans_info {
+ u8 mbo_transition_reason;
+ u8 n_candidates;
+ u8 *bssid;
+};
+
+struct wpa_bss_candidate_info {
+ u8 num;
+ struct candidate_list {
+ u8 bssid[ETH_ALEN];
+ u8 is_accept;
+ u32 reject_reason;
+ } *candidates;
+};
+
+struct wpa_pmkid_params {
+ const u8 *bssid;
+ const u8 *ssid;
+ size_t ssid_len;
+ const u8 *fils_cache_id;
+ const u8 *pmkid;
+ const u8 *pmk;
+ size_t pmk_len;
+};
+
+/* Mask used to specify which connection parameters have to be updated */
+enum wpa_drv_update_connect_params_mask {
+ WPA_DRV_UPDATE_ASSOC_IES = BIT(0),
+ WPA_DRV_UPDATE_FILS_ERP_INFO = BIT(1),
+ WPA_DRV_UPDATE_AUTH_TYPE = BIT(2),
+};
+
+/**
+ * struct external_auth - External authentication trigger parameters
+ *
+ * These are used across the external authentication request and event
+ * interfaces.
+ * @action: Action type / trigger for external authentication. Only significant
+ * for the event interface.
+ * @bssid: BSSID of the peer with which the authentication has to happen. Used
+ * by both the request and event interface.
+ * @ssid: SSID of the AP. Used by both the request and event interface.
+ * @ssid_len: SSID length in octets.
+ * @key_mgmt_suite: AKM suite of the respective authentication. Optional for
+ * the request interface.
+ * @status: Status code, %WLAN_STATUS_SUCCESS for successful authentication,
+ * use %WLAN_STATUS_UNSPECIFIED_FAILURE if wpa_supplicant cannot give
+ * the real status code for failures. Used only for the request interface
+ * from user space to the driver.
+ */
+struct external_auth {
+ enum {
+ EXT_AUTH_START,
+ EXT_AUTH_ABORT,
+ } action;
+ u8 bssid[ETH_ALEN];
+ u8 ssid[SSID_MAX_LEN];
+ size_t ssid_len;
+ unsigned int key_mgmt_suite;
+ u16 status;
+};
/**
* struct wpa_driver_ops - Driver interface API definition
/**
* add_pmkid - Add PMKSA cache entry to the driver
* @priv: private driver interface data
- * @bssid: BSSID for the PMKSA cache entry
- * @pmkid: PMKID for the PMKSA cache entry
+ * @params: PMKSA parameters
*
* Returns: 0 on success, -1 on failure
*
* This function is called when a new PMK is received, as a result of
- * either normal authentication or RSN pre-authentication.
+ * either normal authentication or RSN pre-authentication. The PMKSA
+ * parameters are either a set of bssid, pmkid, and pmk; or a set of
+ * ssid, fils_cache_id, pmkid, and pmk.
*
* If the driver generates RSN IE, i.e., it does not use wpa_ie in
* associate(), add_pmkid() can be used to add new PMKSA cache entries
* driver_ops function does not need to be implemented. Likewise, if
* the driver does not support WPA, this function is not needed.
*/
- int (*add_pmkid)(void *priv, const u8 *bssid, const u8 *pmkid);
+ int (*add_pmkid)(void *priv, struct wpa_pmkid_params *params);
/**
* remove_pmkid - Remove PMKSA cache entry to the driver
* @priv: private driver interface data
- * @bssid: BSSID for the PMKSA cache entry
- * @pmkid: PMKID for the PMKSA cache entry
+ * @params: PMKSA parameters
*
* Returns: 0 on success, -1 on failure
*
* This function is called when the supplicant drops a PMKSA cache
- * entry for any reason.
+ * entry for any reason. The PMKSA parameters are either a set of
+ * bssid and pmkid; or a set of ssid, fils_cache_id, and pmkid.
*
* If the driver generates RSN IE, i.e., it does not use wpa_ie in
* associate(), remove_pmkid() can be used to synchronize PMKSA caches
* implemented. Likewise, if the driver does not support WPA, this
* function is not needed.
*/
- int (*remove_pmkid)(void *priv, const u8 *bssid, const u8 *pmkid);
+ int (*remove_pmkid)(void *priv, struct wpa_pmkid_params *params);
/**
* flush_pmkid - Flush PMKSA cache
* @priv: Private driver interface data
* @num_modes: Variable for returning the number of returned modes
* flags: Variable for returning hardware feature flags
+ * @dfs: Variable for returning DFS region (HOSTAPD_DFS_REGION_*)
* Returns: Pointer to allocated hardware data on success or %NULL on
* failure. Caller is responsible for freeing this.
*/
struct hostapd_hw_modes * (*get_hw_feature_data)(void *priv,
u16 *num_modes,
- u16 *flags);
+ u16 *flags, u8 *dfs);
/**
* send_mlme - Send management frame from MLME
* transmitted on that channel; alternatively the frame may be sent on
* the current operational channel (if in associated state in station
* mode or while operating as an AP.)
+ *
+ * If @src differs from the device MAC address, use of a random
+ * transmitter address is requested for this message exchange.
*/
int (*send_action)(void *priv, unsigned int freq, unsigned int wait,
const u8 *dst, const u8 *src, const u8 *bssid,
/**
* sta_auth - Station authentication indication
- * @priv: Private driver interface data
- * @own_addr: Source address and BSSID for authentication frame
- * @addr: MAC address of the station to associate
- * @seq: authentication sequence number
- * @status: authentication response status code
- * @ie: authentication frame ie buffer
- * @len: ie buffer length
+ * @priv: private driver interface data
+ * @params: Station authentication parameters
*
- * This function indicates the driver to send Authentication frame
- * to the station.
+ * Returns: 0 on success, -1 on failure
*/
- int (*sta_auth)(void *priv, const u8 *own_addr, const u8 *addr,
- u16 seq, u16 status, const u8 *ie, size_t len);
+ int (*sta_auth)(void *priv,
+ struct wpa_driver_sta_auth_params *params);
/**
* add_tspec - Add traffic stream
*/
int (*roaming)(void *priv, int allowed, const u8 *bssid);
+ /**
+ * disable_fils - Enable/disable FILS feature
+ * @priv: Private driver interface data
+ * @disable: 0-enable and 1-disable FILS feature
+ * Returns: 0 on success, -1 on failure
+ *
+ * This callback can be used to configure driver and below layers to
+ * enable/disable all FILS features.
+ */
+ int (*disable_fils)(void *priv, int disable);
+
/**
* set_mac_addr - Set MAC address
* @priv: Private driver interface data
*/
int (*enable_protect_frames)(void *priv, Boolean enabled);
+ /**
+ * enable_encrypt - Set encryption status
+ * @priv: Private driver interface data
+ * @enabled: TRUE = encrypt outgoing traffic
+ * FALSE = integrity-only protection on outgoing traffic
+ * Returns: 0 on success, -1 on failure (or if not supported)
+ */
+ int (*enable_encrypt)(void *priv, Boolean enabled);
+
/**
* set_replay_protect - Set replay protect status and window size
* @priv: Private driver interface data
*/
int (*set_transmit_next_pn)(void *priv, struct transmit_sa *sa);
- /**
- * get_available_receive_sc - get available receive channel
- * @priv: Private driver interface data
- * @channel: secure channel
- * Returns: 0 on success, -1 on failure (or if not supported)
- */
- int (*get_available_receive_sc)(void *priv, u32 *channel);
-
/**
* create_receive_sc - create secure channel for receiving
* @priv: Private driver interface data
*/
int (*create_receive_sa)(void *priv, struct receive_sa *sa);
+ /**
+ * delete_receive_sa - Delete secure association for receive
+ * @priv: Private driver interface data from init()
+ * @sa: Secure association
+ * Returns: 0 on success, -1 on failure
+ */
+ int (*delete_receive_sa)(void *priv, struct receive_sa *sa);
+
/**
* enable_receive_sa - enable the SA for receive
* @priv: private driver interface data from init()
*/
int (*disable_receive_sa)(void *priv, struct receive_sa *sa);
- /**
- * get_available_transmit_sc - get available transmit channel
- * @priv: Private driver interface data
- * @channel: secure channel
- * Returns: 0 on success, -1 on failure (or if not supported)
- */
- int (*get_available_transmit_sc)(void *priv, u32 *channel);
-
/**
* create_transmit_sc - create secure connection for transmit
* @priv: private driver interface data from init()
*/
int (*create_transmit_sa)(void *priv, struct transmit_sa *sa);
+ /**
+ * delete_transmit_sa - Delete secure association for transmit
+ * @priv: Private driver interface data from init()
+ * @sa: Secure association
+ * Returns: 0 on success, -1 on failure
+ */
+ int (*delete_transmit_sa)(void *priv, struct transmit_sa *sa);
+
/**
* enable_transmit_sa - enable SA for transmit
* @priv: private driver interface data from init()
/**
* abort_scan - Request the driver to abort an ongoing scan
* @priv: Private driver interface data
+ * @scan_cookie: Cookie identifying the scan request. This is used only
+ * when the vendor interface QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN
+ * was used to trigger scan. Otherwise, 0 is used.
* Returns 0 on success, -1 on failure
*/
- int (*abort_scan)(void *priv);
+ int (*abort_scan)(void *priv, u64 scan_cookie);
/**
* configure_data_frame_filters - Request to configure frame filters
*/
int (*set_default_scan_ies)(void *priv, const u8 *ies, size_t ies_len);
-};
+ /**
+ * set_tdls_mode - Set TDLS trigger mode to the host driver
+ * @priv: Private driver interface data
+ * @tdls_external_control: Represents if TDLS external trigger control
+ * mode is enabled/disabled.
+ *
+ * This optional callback can be used to configure the TDLS external
+ * trigger control mode to the host driver.
+ */
+ int (*set_tdls_mode)(void *priv, int tdls_external_control);
+
+ /**
+ * get_bss_transition_status - Get candidate BSS's transition status
+ * @priv: Private driver interface data
+ * @params: Candidate BSS list
+ *
+ * Get the accept or reject reason code for a list of BSS transition
+ * candidates.
+ */
+ struct wpa_bss_candidate_info *
+ (*get_bss_transition_status)(void *priv,
+ struct wpa_bss_trans_info *params);
+ /**
+ * ignore_assoc_disallow - Configure driver to ignore assoc_disallow
+ * @priv: Private driver interface data
+ * @ignore_disallow: 0 to not ignore, 1 to ignore
+ * Returns: 0 on success, -1 on failure
+ */
+ int (*ignore_assoc_disallow)(void *priv, int ignore_disallow);
+
+ /**
+ * set_bssid_blacklist - Set blacklist of BSSIDs to the driver
+ * @priv: Private driver interface data
+ * @num_bssid: Number of blacklist BSSIDs
+ * @bssids: List of blacklisted BSSIDs
+ */
+ int (*set_bssid_blacklist)(void *priv, unsigned int num_bssid,
+ const u8 *bssid);
+
+ /**
+ * update_connect_params - Update the connection parameters
+ * @priv: Private driver interface data
+ * @params: Association parameters
+ * @mask: Bit mask indicating which parameters in @params have to be
+ * updated
+ * Returns: 0 on success, -1 on failure
+ *
+ * Update the connection parameters when in connected state so that the
+ * driver uses the updated parameters for subsequent roaming. This is
+ * used only with drivers that implement internal BSS selection and
+ * roaming.
+ */
+ int (*update_connect_params)(
+ void *priv, struct wpa_driver_associate_params *params,
+ enum wpa_drv_update_connect_params_mask mask);
+ /**
+ * send_external_auth_status - Indicate the status of external
+ * authentication processing to the host driver.
+ * @priv: Private driver interface data
+ * @params: Status of authentication processing.
+ * Returns: 0 on success, -1 on failure
+ */
+ int (*send_external_auth_status)(void *priv,
+ struct external_auth *params);
+};
/**
* enum wpa_event_type - Event type for wpa_supplicant_event() calls
*/
EVENT_PMKID_CANDIDATE,
- /**
- * EVENT_STKSTART - Request STK handshake (MLME-STKSTART.request)
- *
- * This event can be used to inform wpa_supplicant about desire to set
- * up secure direct link connection between two stations as defined in
- * IEEE 802.11e with a new PeerKey mechanism that replaced the original
- * STAKey negotiation. The caller will need to set peer address for the
- * event.
- */
- EVENT_STKSTART,
-
/**
* EVENT_TDLS - Request TDLS operation
*
* EVENT_DFS_CAC_ABORTED - Notify that channel availability check has been aborted
*
* The CAC was not successful, and the channel remains in the previous
- * state. This may happen due to a radar beeing detected or other
+ * state. This may happen due to a radar being detected or other
* external influences.
*/
EVENT_DFS_CAC_ABORTED,
* EVENT_P2P_LO_STOP - Notify that P2P listen offload is stopped
*/
EVENT_P2P_LO_STOP,
+
+ /**
+ * EVENT_BEACON_LOSS - Beacon loss detected
+ *
+ * This event indicates that no Beacon frames has been received from
+ * the current AP. This may indicate that the AP is not anymore in
+ * range.
+ */
+ EVENT_BEACON_LOSS,
+
+ /**
+ * EVENT_DFS_PRE_CAC_EXPIRED - Notify that channel availability check
+ * done previously (Pre-CAC) on the channel has expired. This would
+ * normally be on a non-ETSI DFS regulatory domain. DFS state of the
+ * channel will be moved from available to usable. A new CAC has to be
+ * performed before start operating on this channel.
+ */
+ EVENT_DFS_PRE_CAC_EXPIRED,
+
+ /**
+ * EVENT_EXTERNAL_AUTH - This event interface is used by host drivers
+ * that do not define separate commands for authentication and
+ * association (~WPA_DRIVER_FLAGS_SME) but offload the 802.11
+ * authentication to wpa_supplicant. This event carries all the
+ * necessary information from the host driver for the authentication to
+ * happen.
+ */
+ EVENT_EXTERNAL_AUTH,
+
+ /**
+ * EVENT_PORT_AUTHORIZED - Notification that a connection is authorized
+ *
+ * This event should be indicated when the driver completes the 4-way
+ * handshake. This event should be preceded by an EVENT_ASSOC that
+ * indicates the completion of IEEE 802.11 association.
+ */
+ EVENT_PORT_AUTHORIZED,
+
+ /**
+ * EVENT_STATION_OPMODE_CHANGED - Notify STA's HT/VHT operation mode
+ * change event.
+ */
+ EVENT_STATION_OPMODE_CHANGED,
+
+ /**
+ * EVENT_INTERFACE_MAC_CHANGED - Notify that interface MAC changed
+ *
+ * This event is emitted when the MAC changes while the interface is
+ * enabled. When an interface was disabled and becomes enabled, it
+ * must be always assumed that the MAC possibly changed.
+ */
+ EVENT_INTERFACE_MAC_CHANGED,
+
+ /**
+ * EVENT_WDS_STA_INTERFACE_STATUS - Notify WDS STA interface status
+ *
+ * This event is emitted when an interface is added/removed for WDS STA.
+ */
+ EVENT_WDS_STA_INTERFACE_STATUS,
};
/**
* ptk_kek - The derived PTK KEK
+ * This is used in key management offload and also in FILS SK
+ * offload.
*/
const u8 *ptk_kek;
* 0 = unknown, 1 = unchanged, 2 = changed
*/
u8 subnet_status;
+
+ /**
+ * The following information is used in FILS SK offload
+ * @fils_erp_next_seq_num
+ * @fils_pmk
+ * @fils_pmk_len
+ * @fils_pmkid
+ */
+
+ /**
+ * fils_erp_next_seq_num - The next sequence number to use in
+ * FILS ERP messages
+ */
+ u16 fils_erp_next_seq_num;
+
+ /**
+ * fils_pmk - A new PMK if generated in case of FILS
+ * authentication
+ */
+ const u8 *fils_pmk;
+
+ /**
+ * fils_pmk_len - Length of fils_pmk
+ */
+ size_t fils_pmk_len;
+
+ /**
+ * fils_pmkid - PMKID used or generated in FILS authentication
+ */
+ const u8 *fils_pmkid;
} assoc_info;
/**
int preauth;
} pmkid_candidate;
- /**
- * struct stkstart - Data for EVENT_STKSTART
- */
- struct stkstart {
- u8 peer[ETH_ALEN];
- } stkstart;
-
/**
* struct tdls - Data for EVENT_TDLS
*/
* than explicit rejection response from the AP.
*/
int timed_out;
+
+ /**
+ * timeout_reason - Reason for the timeout
+ */
+ const char *timeout_reason;
+
+ /**
+ * fils_erp_next_seq_num - The next sequence number to use in
+ * FILS ERP messages
+ */
+ u16 fils_erp_next_seq_num;
} assoc_reject;
struct timeout_event {
* @external_scan: Whether the scan info is for an external scan
* @nl_scan_event: 1 if the source of this scan event is a normal scan,
* 0 if the source of the scan event is a vendor scan
+ * @scan_start_tsf: Time when the scan started in terms of TSF of the
+ * BSS that the interface that requested the scan is connected to
+ * (if available).
+ * @scan_start_tsf_bssid: The BSSID according to which %scan_start_tsf
+ * is set.
*/
struct scan_info {
int aborted;
size_t num_ssids;
int external_scan;
int nl_scan_event;
+ u64 scan_start_tsf;
+ u8 scan_start_tsf_bssid[ETH_ALEN];
} scan_info;
/**
/**
* struct low_ack - Data for EVENT_STATION_LOW_ACK events
* @addr: station address
+ * @num_packets: Number of packets lost (consecutive packets not
+ * acknowledged)
*/
struct low_ack {
u8 addr[ETH_ALEN];
+ u32 num_packets;
} low_ack;
/**
P2P_LO_STOPPED_REASON_NOT_SUPPORTED,
} reason_code;
} p2p_lo_stop;
+
+ /* For EVENT_EXTERNAL_AUTH */
+ struct external_auth external_auth;
+
+ /**
+ * struct sta_opmode - Station's operation mode change event
+ * @addr: The station MAC address
+ * @smps_mode: SMPS mode of the station
+ * @chan_width: Channel width of the station
+ * @rx_nss: RX_NSS of the station
+ *
+ * This is used as data with EVENT_STATION_OPMODE_CHANGED.
+ */
+ struct sta_opmode {
+ const u8 *addr;
+ enum smps_mode smps_mode;
+ enum chan_width chan_width;
+ u8 rx_nss;
+ } sta_opmode;
+
+ /**
+ * struct wds_sta_interface - Data for EVENT_WDS_STA_INTERFACE_STATUS.
+ */
+ struct wds_sta_interface {
+ const u8 *sta_addr;
+ const char *ifname;
+ enum {
+ INTERFACE_ADDED,
+ INTERFACE_REMOVED
+ } istatus;
+ } wds_sta_interface;
};
/**
/* driver_macsec_qca.c */
extern const struct wpa_driver_ops wpa_driver_macsec_qca_ops;
#endif /* CONFIG_DRIVER_MACSEC_QCA */
+#ifdef CONFIG_DRIVER_MACSEC_LINUX
+/* driver_macsec_linux.c */
+extern const struct wpa_driver_ops wpa_driver_macsec_linux_ops;
+#endif /* CONFIG_DRIVER_MACSEC_LINUX */
#ifdef CONFIG_DRIVER_ROBOSWITCH
/* driver_roboswitch.c */
extern const struct wpa_driver_ops wpa_driver_roboswitch_ops;
projects / thirdparty / hostap.git / blobdiff