# to external program(s)
#wps_cred_processing=0
+# Whether to enable SAE (WPA3-Personal transition mode) automatically for
+# WPA2-PSK credentials received using WPS.
+# 0 = only add the explicitly listed WPA2-PSK configuration (default)
+# 1 = add both the WPA2-PSK and SAE configuration and enable PMF so that the
+# station gets configured in WPA3-Personal transition mode (supports both
+# WPA2-Personal (PSK) and WPA3-Personal (SAE) APs).
+#wps_cred_add_sae=0
+
# Vendor attribute in WPS M1, e.g., Windows 7 Vertical Pairing
# The vendor attribute contents to be added in M1 (hex string)
#wps_vendor_ext_m1=000137100100020001
# of APs when using ap_scan=1 mode.
#bss_max_count=200
+# BSS expiration age in seconds. A BSS will be removed from the local cache
+# if it is not in use and has not been seen for this time. Default is 180.
+#bss_expiration_age=180
+
+# BSS expiration after number of scans. A BSS will be removed from the local
+# cache if it is not seen in this number of scans.
+# Default is 2.
+#bss_expiration_scan_count=2
+
# Automatic scan
# This is an optional set of parameters for automatic scanning
# within an interface in following format:
# Enabled SAE finite cyclic groups in preference order
# By default (if this parameter is not set), the mandatory group 19 (ECC group
-# defined over a 256-bit prime order field) is preferred, but other groups are
-# also enabled. If this parameter is set, the groups will be tried in the
-# indicated order. The group values are listed in the IANA registry:
+# defined over a 256-bit prime order field, NIST P-256) is preferred and groups
+# 20 (NIST P-384) and 21 (NIST P-521) are also enabled. If this parameter is
+# set, the groups will be tried in the indicated order.
+# The group values are listed in the IANA registry:
# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9
-#sae_groups=21 20 19 26 25
+# Note that groups 1, 2, 5, 22, 23, and 24 should not be used in production
+# purposes due limited security (see RFC 8247). Groups that are not as strong as
+# group 19 (ECC, NIST P-256) are unlikely to be useful for production use cases
+# since all implementations are required to support group 19.
+#sae_groups=19 20 21
# Default value for DTIM period (if not overridden in network block)
#dtim_period=2
# pre-configured with the credential since the NAI Realm information
# may not be available or fetched.
#
+# required_roaming_consortium: Required Roaming Consortium OI
+# If required_roaming_consortium_len is non-zero, this field contains the
+# Roaming Consortium OI that is required to be advertised by the AP for
+# the credential to be considered matching.
+#
+# roaming_consortiums: Roaming Consortium OI(s) memberships
+# This string field contains one or more comma delimited OIs (hexdump)
+# identifying the roaming consortiums of which the provider is a member.
+# The list is sorted from the most preferred one to the least preferred
+# one. A match between the Roaming Consortium OIs advertised by an AP and
+# the OIs in this list indicates that successful authentication is
+# possible.
+# (Hotspot 2.0 PerProviderSubscription/<X+>/HomeSP/RoamingConsortiumOI)
+#
# eap: Pre-configured EAP method
# This optional field can be used to specify which EAP method will be
# used with this credential. If not set, the EAP method is selected
# proto: list of accepted protocols
# WPA = WPA/IEEE 802.11i/D3.0
# RSN = WPA2/IEEE 802.11i (also WPA2 can be used as an alias for RSN)
+# Note that RSN is used also for WPA3.
# If not set, this defaults to: WPA RSN
#
# key_mgmt: list of accepted authenticated key management protocols
# instead)
# FT-PSK = Fast BSS Transition (IEEE 802.11r) with pre-shared key
# FT-EAP = Fast BSS Transition (IEEE 802.11r) with EAP authentication
+# FT-EAP-SHA384 = Fast BSS Transition (IEEE 802.11r) with EAP authentication
+# and using SHA384
# WPA-PSK-SHA256 = Like WPA-PSK but using stronger SHA256-based algorithms
# WPA-EAP-SHA256 = Like WPA-EAP but using stronger SHA256-based algorithms
# SAE = Simultaneous authentication of equals; pre-shared key/password -based
# authentication with stronger security than WPA-PSK especially when using
-# not that strong password
+# not that strong password; a.k.a. WPA3-Personal
# FT-SAE = SAE with FT
# WPA-EAP-SUITE-B = Suite B 128-bit level
# WPA-EAP-SUITE-B-192 = Suite B 192-bit level
# FILS-SHA384 = Fast Initial Link Setup with SHA384
# FT-FILS-SHA256 = FT and Fast Initial Link Setup with SHA256
# FT-FILS-SHA384 = FT and Fast Initial Link Setup with SHA384
+# OWE = Opportunistic Wireless Encryption (a.k.a. Enhanced Open)
+# DPP = Device Provisioning Protocol
# If not set, this defaults to: WPA-PSK WPA-EAP
#
# ieee80211w: whether management frame protection is enabled
# PMF required: ieee80211w=2 and key_mgmt=WPA-EAP-SHA256
# (and similarly for WPA-PSK and WPA-WPSK-SHA256 if WPA2-Personal is used)
#
+# ocv: whether operating channel validation is enabled
+# This is a countermeasure against multi-channel man-in-the-middle attacks.
+# Enabling this automatically also enables ieee80211w, if not yet enabled.
+# 0 = disabled (default)
+# 1 = enabled
+#ocv=1
+#
# auth_alg: list of allowed IEEE 802.11 authentication algorithms
# OPEN = Open System authentication (required for WPA/WPA2)
# SHARED = Shared Key authentication (requires static WEP keys)
#
# sae_password: SAE password
# This parameter can be used to set a password for SAE. By default, the
-# passphrase value is used if this separate parameter is not used, but
-# passphrase follows the WPA-PSK constraints (8..63 characters) even
-# though SAE passwords do not have such constraints.
+# passphrase from the psk parameter is used if this separate parameter is not
+# used, but psk follows the WPA-PSK constraints (8..63 characters) even though
+# SAE passwords do not have such constraints.
+#
+# sae_password_id: SAE password identifier
+# This parameter can be used to set an identifier for the SAE password. By
+# default, no such identifier is used. If set, the specified identifier value
+# is used by the other peer to select which password to use for authentication.
#
# eapol_flags: IEEE 802.1X/EAPOL options (bit field)
# Dynamic WEP key required for non-WPA mode
# 0: Encrypt traffic (default)
# 1: Integrity only
#
+# macsec_replay_protect: IEEE 802.1X/MACsec replay protection
+# This setting applies only when MACsec is in use, i.e.,
+# - macsec_policy is enabled
+# - the key server has decided to enable MACsec
+# 0: Replay protection disabled (default)
+# 1: Replay protection enabled
+#
+# macsec_replay_window: IEEE 802.1X/MACsec replay protection window
+# This determines a window in which replay is tolerated, to allow receipt
+# of frames that have been misordered by the network.
+# This setting applies only when MACsec replay protection active, i.e.,
+# - macsec_replay_protect is enabled
+# - the key server has decided to enable MACsec
+# 0: No replay window, strict check (default)
+# 1..2^32-1: number of packets that could be misordered
+#
# macsec_port: IEEE 802.1X/MACsec port
# Port component of the SCI
# Range: 1-65534 (default: 1)
# This allows to configure MACsec with a pre-shared key using a (CAK,CKN) pair.
# In this mode, instances of wpa_supplicant can act as MACsec peers. The peer
# with lower priority will become the key server and start distributing SAKs.
-# mka_cak (CAK = Secure Connectivity Association Key) takes a 16-bytes (128 bit)
-# hex-string (32 hex-digits)
-# mka_ckn (CKN = CAK Name) takes a 32-bytes (256 bit) hex-string (64 hex-digits)
+# mka_cak (CAK = Secure Connectivity Association Key) takes a 16-byte (128-bit)
+# hex-string (32 hex-digits) or a 32-byte (256-bit) hex-string (64 hex-digits)
+# mka_ckn (CKN = CAK Name) takes a 1..32-bytes (8..256 bit) hex-string
+# (2..64 hex-digits)
# mka_priority (Priority of MKA Actor) is in 0..255 range with 255 being
# default priority
#
# 0 = disabled (default unless changed with the global okc parameter)
# 1 = enabled
#
+# ft_eap_pmksa_caching:
+# Whether FT-EAP PMKSA caching is allowed
+# 0 = do not try to use PMKSA caching with FT-EAP (default)
+# 1 = try to use PMKSA caching with FT-EAP
+# This controls whether to try to use PMKSA caching with FT-EAP for the
+# FT initial mobility domain association.
+#ft_eap_pmksa_caching=0
+#
# wep_key0..3: Static WEP key (ASCII in double quotation, e.g. "abcde" or
# hex without quotation, e.g., 0102030405)
# wep_tx_keyidx: Default WEP key index (TX) (0..3)
# certificate may include additional sub-level labels in addition to the
# required labels.
#
+# More than one match string can be provided by using semicolons to
+# separate the strings (e.g., example.org;example.com). When multiple
+# strings are specified, a match with any one of the values is considered
+# a sufficient match for the certificate, i.e., the conditions are ORed
+# together.
+#
# For example, domain_suffix_match=example.com would match
# test.example.com but would not match test-example.com.
# domain_match: Constraint for server domain name
# no subdomains or wildcard matches are allowed. Case-insensitive
# comparison is used, so "Example.com" matches "example.com", but would
# not match "test.Example.com".
+#
+# More than one match string can be provided by using semicolons to
+# separate the strings (e.g., example.org;example.com). When multiple
+# strings are specified, a match with any one of the values is considered
+# a sufficient match for the certificate, i.e., the conditions are ORed
+# together.
# phase1: Phase1 (outer authentication, i.e., TLS tunnel) parameters
# (string with field-value pairs, e.g., "peapver=0" or
# "peapver=1 peaplabel=1")
# For EAP-FAST, this must be set to 0 (or left unconfigured for the
# default value to be used automatically).
# tls_disable_tlsv1_0=1 - disable use of TLSv1.0
+# tls_disable_tlsv1_0=0 - explicitly enable use of TLSv1.0 (this allows
+# systemwide TLS policies to be overridden)
# tls_disable_tlsv1_1=1 - disable use of TLSv1.1 (a workaround for AAA servers
# that have issues interoperating with updated TLS version)
+# tls_disable_tlsv1_1=0 - explicitly enable use of TLSv1.1 (this allows
+# systemwide TLS policies to be overridden)
# tls_disable_tlsv1_2=1 - disable use of TLSv1.2 (a workaround for AAA servers
# that have issues interoperating with updated TLS version)
+# tls_disable_tlsv1_2=0 - explicitly enable use of TLSv1.2 (this allows
+# systemwide TLS policies to be overridden)
+# tls_disable_tlsv1_3=1 - disable use of TLSv1.3 (a workaround for AAA servers
+# that have issues interoperating with updated TLS version)
+# tls_disable_tlsv1_3=0 - enable TLSv1.3 (experimental - disabled by default)
# tls_ext_cert_check=0 - No external server certificate validation (default)
# tls_ext_cert_check=1 - External server certificate validation enabled; this
# requires an external program doing validation of server certificate
# update_identifier: PPS MO ID
# (Hotspot 2.0 PerProviderSubscription/UpdateIdentifier)
+#
+# roaming_consortium_selection: Roaming Consortium Selection
+# The matching Roaming Consortium OI that was used to generate this
+# network profile.
# Station inactivity limit
#
# Treated as hint by the kernel.
# -1 = Do not make any changes.
# 0-3 = Set AMPDU density (aka factor) to specified value.
+#
+# tx_stbc: Allow overriding STBC support for TX streams
+# Value: 0-1, see IEEE Std 802.11-2016, 9.4.2.56.2.
+# -1 = Do not make any changes (default)
+# 0 = Set if not supported
+# 1 = Set if supported
+#
+# rx_stbc: Allow overriding STBC support for RX streams
+# Value: 0-3, see IEEE Std 802.11-2016, 9.4.2.56.2.
+# -1 = Do not make any changes (default)
+# 0 = Set if not supported
+# 1 = Set for support of one spatial stream
+# 2 = Set for support of one and two spatial streams
+# 3 = Set for support of one, two and three spatial streams
# disable_vht: Whether VHT should be disabled.
# 0 = VHT enabled (if AP supports it)
# 2: MCS 0-9
# 3: not supported
+# multi_ap_backhaul_sta: Multi-AP backhaul STA functionality
+# 0 = normal STA (default)
+# 1 = backhaul STA
+# A backhaul STA sends the Multi-AP IE, fails to associate if the AP does not
+# support Multi-AP, and sets 4-address mode if it does. Thus, the netdev can be
+# added to a bridge to allow forwarding frames over this backhaul link.
+
##### Fast Session Transfer (FST) support #####################################
#
# The options in this section are only available when the build configuration
# Transitioning between states).
#fst_llt=100
+# BSS Transition Management
+# disable_btm - Disable BSS transition management in STA
+# Set to 0 to enable BSS transition management (default behavior)
+# Set to 1 to disable BSS transition management
+#disable_btm=0
+
# Example blocks:
# Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers
}
-# Example MACsec configuration
-#network={
-# key_mgmt=IEEE8021X
-# eap=TTLS
-# phase2="auth=PAP"
-# anonymous_identity="anonymous@example.com"
-# identity="user@example.com"
-# password="secretr"
-# ca_cert="/etc/cert/ca.pem"
-# eapol_flags=0
-# macsec_policy=1
-#}
+# Example configuration using EAP-TTLS for authentication and key
+# generation for MACsec
+network={
+ key_mgmt=IEEE8021X
+ eap=TTLS
+ phase2="auth=PAP"
+ anonymous_identity="anonymous@example.com"
+ identity="user@example.com"
+ password="secretr"
+ ca_cert="/etc/cert/ca.pem"
+ eapol_flags=0
+ macsec_policy=1
+}
+
+# Example configuration for MACsec with preshared key
+network={
+ key_mgmt=NONE
+ eapol_flags=0
+ macsec_policy=1
+ mka_cak=0123456789ABCDEF0123456789ABCDEF
+ mka_ckn=6162636465666768696A6B6C6D6E6F707172737475767778797A303132333435
+ mka_priority=128
+}
projects / thirdparty / hostap.git / blobdiff