X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=Kconfig;h=a44ac9149c5d51033d759cf050b60cbe2f3537de;hb=19271138fff79419b0c25e3570ed58046dba1780;hp=2afbaaf801ad5117d9e74da99a56bea4c292395a;hpb=da74d1f341e46ecc0ae893b4aa3b771ce9dba9f3;p=people%2Fms%2Fu-boot.git

diff --git a/Kconfig b/Kconfig
index 2afbaaf801..a44ac9149c 100644
--- a/Kconfig
+++ b/Kconfig
@@ -55,10 +55,13 @@ config CC_OPTIMIZE_FOR_SIZE
 
 config DISTRO_DEFAULTS
 	bool "Select defaults suitable for booting general purpose Linux distributions"
-	default y if ARCH_SUNXI
+	default y if ARCH_SUNXI || TEGRA
+	default y if ARCH_LS2080A
 	default n
-	select CMD_BOOTZ
+	select CMD_BOOTZ if ARM && !ARM64
+	select CMD_BOOTI if ARM64
 	select CMD_DHCP
+	select CMD_PXE
 	select CMD_EXT2
 	select CMD_EXT4
 	select CMD_FAT
@@ -114,78 +117,27 @@ if EXPERT
 	  Warning:
 	  When disabling this, please check if malloc calls, maybe
 	  should be replaced by calloc - if one expects zeroed memory.
-endif
-endmenu		# General setup
-
-menu "Boot images"
 
-config SUPPORT_SPL
-	bool
-
-config SUPPORT_TPL
-	bool
-
-config SPL
-	bool
-	depends on SUPPORT_SPL
-	prompt "Enable SPL"
+config TOOLS_DEBUG
+	bool "Enable debug information for tools"
 	help
-	  If you want to build SPL as well as the normal image, say Y.
+	  Enable generation of debug information for tools such as mkimage.
+	  This can be used for debugging purposes. With debug information
+	  it is possible to set breakpoints on particular lines, single-step
+	  debug through the source code, etc.
 
-config SPL_SYS_MALLOC_SIMPLE
-	bool
-	depends on SPL
-	prompt "Only use malloc_simple functions in the SPL"
-	help
-	  Say Y here to only use the *_simple malloc functions from
-	  malloc_simple.c, rather then using the versions from dlmalloc.c;
-	  this will make the SPL binary smaller at the cost of more heap
-	  usage as the *_simple malloc functions do not re-use free-ed mem.
+endif
 
-config SPL_STACK_R
-	depends on SPL
-	bool "Enable SDRAM location for SPL stack"
+config PHYS_64BIT
+	bool "64bit physical address support"
 	help
-	  SPL starts off execution in SRAM and thus typically has only a small
-	  stack available. Since SPL sets up DRAM while in its board_init_f()
-	  function, it is possible for the stack to move there before
-	  board_init_r() is reached. This option enables a special SDRAM
-	  location for the SPL stack. U-Boot SPL switches to this after
-	  board_init_f() completes, and before board_init_r() starts.
-
-config SPL_STACK_R_ADDR
-	depends on SPL_STACK_R
-	hex "SDRAM location for SPL stack"
-	help
-	  Specify the address in SDRAM for the SPL stack. This will be set up
-	  before board_init_r() is called.
+	  Say Y here to support 64bit physical memory address.
+	  This can be used not only for 64bit SoCs, but also for
+	  large physical address extention on 32bit SoCs.
 
-config SPL_STACK_R_MALLOC_SIMPLE_LEN
-	depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
-	hex "Size of malloc_simple heap after switching to DRAM SPL stack"
-	default 0x100000
-	help
-	  Specify the amount of the stack to use as memory pool for
-	  malloc_simple after switching the stack to DRAM. This may be set
-	  to give board_init_r() a larger heap then the initial heap in
-	  SRAM which is limited to SYS_MALLOC_F_LEN bytes.
+endmenu		# General setup
 
-config SPL_SEPARATE_BSS
-	depends on SPL
-	bool "BSS section is in a different memory region from text"
-	help
-	  Some platforms need a large BSS region in SPL and can provide this
-	  because RAM is already set up. In this case BSS can be moved to RAM.
-	  This option should then be enabled so that the correct device tree
-	  location is used. Normally we put the device tree at the end of BSS
-	  but with this option enabled, it goes at _image_binary_end.
-
-config TPL
-	bool
-	depends on SPL && SUPPORT_TPL
-	prompt "Enable TPL"
-	help
-	  If you want to build TPL as well as the normal image and SPL, say Y.
+menu "Boot images"
 
 config FIT
 	bool "Support Flattened Image Tree"
@@ -327,12 +279,34 @@ config SPL_FIT_IMAGE_POST_PROCESS
 	  injected into the FIT creation (i.e. the blobs would have been pre-
 	  processed before being added to the FIT image).
 
+config FIT_IMAGE_POST_PROCESS
+	bool "Enable post-processing of FIT artifacts after loading by U-Boot"
+	depends on FIT && TI_SECURE_DEVICE
+	help
+	  Allows doing any sort of manipulation to blobs after they got extracted
+	  from FIT images like stripping off headers or modifying the size of the
+	  blob, verification, authentication, decryption etc. in a platform or
+	  board specific way. In order to use this feature a platform or board-
+	  specific implementation of board_fit_image_post_process() must be
+	  provided. Also, anything done during this post-processing step would
+	  need to be comprehended in how the images were prepared before being
+	  injected into the FIT creation (i.e. the blobs would have been pre-
+	  processed before being added to the FIT image).
+
 config SYS_CLK_FREQ
 	depends on ARC || ARCH_SUNXI
 	int "CPU clock frequency"
 	help
 	  TODO: Move CONFIG_SYS_CLK_FREQ for all the architecture
 
+config ARCH_FIXUP_FDT_MEMORY
+	bool "Enable arch_fixup_memory_banks() call"
+	default y
+	help
+	  Enable FDT memory map syncup before OS boot. This feature can be
+	  used for booting OS with different memory setup where the part of
+	  the memory location should be used for different purpose.
+
 endmenu		# Boot images
 
 source "common/Kconfig"