X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=README;h=15016ce92701fc6c0dc24aae7243fd9d5e4cf83d;hb=51a8a72dc5064eb6d2f800a1da883a044b17c58b;hp=a96dd428cbbe5644514469d2fa9dd76812ff4ec6;hpb=3238639d40732fe78fd62ae5e080465552e882fc;p=people%2Fms%2Fu-boot.git diff --git a/README b/README index a96dd428cb..15016ce927 100644 --- a/README +++ b/README @@ -681,8 +681,10 @@ The following options need to be configured: CONFIG_ARM_ERRATA_742230 CONFIG_ARM_ERRATA_743622 CONFIG_ARM_ERRATA_751472 - CONFIG_ARM_ERRATA_794072 CONFIG_ARM_ERRATA_761320 + CONFIG_ARM_ERRATA_773022 + CONFIG_ARM_ERRATA_774769 + CONFIG_ARM_ERRATA_794072 If set, the workarounds for these ARM errata are applied early during U-Boot startup. Note that these options force the @@ -705,6 +707,7 @@ The following options need to be configured: CONFIG_ARM_ERRATA_454179 CONFIG_ARM_ERRATA_621766 CONFIG_ARM_ERRATA_798870 + CONFIG_ARM_ERRATA_801819 - Tegra SoC options: CONFIG_TEGRA_SUPPORT_NON_SECURE @@ -793,18 +796,10 @@ The following options need to be configured: - vxWorks boot parameters: bootvx constructs a valid bootline using the following - environments variables: bootfile, ipaddr, serverip, hostname. + environments variables: bootdev, bootfile, ipaddr, netmask, + serverip, gatewayip, hostname, othbootargs. It loads the vxWorks image pointed bootfile. - CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name - CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address - CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server - CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters - - CONFIG_SYS_VXWORKS_ADD_PARAMS - - Add it at the end of the bootline. E.g "u=username pw=secret" - Note: If a "bootargs" environment is defined, it will overwride the defaults discussed just above. @@ -839,18 +834,6 @@ The following options need to be configured: define this to a list of base addresses for each (supported) port. See e.g. include/configs/versatile.h - CONFIG_PL011_SERIAL_RLCR - - Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) - have separate receive and transmit line control registers. Set - this variable to initialize the extra register. - - CONFIG_PL011_SERIAL_FLUSH_ON_INIT - - On some platforms (e.g. U8500) U-Boot is loaded by a second stage - boot loader that has already initialized the UART. Define this - variable to flush the UART at init time. - CONFIG_SERIAL_HW_FLOW_CONTROL Define this variable to enable hw flow control in serial driver. @@ -889,13 +872,6 @@ The following options need to be configured: (i.e. i8042_tstc) VIDEO_GETC_FCT get char fct (i.e. i8042_getc) - CONFIG_CONSOLE_CURSOR cursor drawing on/off - (requires blink timer - cf. i8042.c) - CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c) - CONFIG_CONSOLE_TIME display time/date info in - upper right corner - (requires CONFIG_CMD_DATE) CONFIG_VIDEO_LOGO display Linux logo in upper left corner CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of @@ -977,8 +953,6 @@ The following options need to be configured: CONFIG_AUTOBOOT_PROMPT CONFIG_AUTOBOOT_DELAY_STR CONFIG_AUTOBOOT_STOP_STR - CONFIG_AUTOBOOT_DELAY_STR2 - CONFIG_AUTOBOOT_STOP_STR2 CONFIG_ZERO_BOOTDELAY_CHECK CONFIG_RESET_TO_RETRY @@ -1050,9 +1024,7 @@ The following options need to be configured: Monitor commands can be included or excluded from the build by using the #include files and #undef'ing unwanted - commands, or using - and augmenting with additional #define's - for wanted commands. + commands, or adding #define's for wanted commands. The default command configuration includes all commands except those marked below with a "*". @@ -1385,9 +1357,6 @@ The following options need to be configured: Management command for E1000 devices. When used on devices with SPI support you can reprogram the EEPROM from U-Boot. - CONFIG_E1000_FALLBACK_MAC - default MAC for empty EEPROM after production. - CONFIG_EEPRO100 Support for Intel 82557/82559/82559ER chips. Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM @@ -1496,16 +1465,10 @@ The following options need to be configured: CONFIG_TPM Support TPM devices. - CONFIG_TPM_TIS_I2C - Support for i2c bus TPM devices. Only one device + CONFIG_TPM_TIS_INFINEON + Support for Infineon i2c bus TPM devices. Only one device per system is supported at this time. - CONFIG_TPM_TIS_I2C_BUS_NUMBER - Define the the i2c bus number for the TPM device - - CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS - Define the TPM's address on the i2c bus - CONFIG_TPM_TIS_I2C_BURST_LIMITATION Define the burst count bytes upper limit @@ -1675,7 +1638,7 @@ The following options need to be configured: key for the Replay Protection Memory Block partition in eMMC. - USB Device Firmware Update (DFU) class support: - CONFIG_DFU_FUNCTION + CONFIG_USB_FUNCTION_DFU This enables the USB portion of the DFU USB class CONFIG_CMD_DFU @@ -1720,6 +1683,9 @@ The following options need to be configured: sending again an USB request to the device. - USB Device Android Fastboot support: + CONFIG_USB_FUNCTION_FASTBOOT + This enables the USB part of the fastboot gadget + CONFIG_CMD_FASTBOOT This enables the command "fastboot" which enables the Android fastboot mode for the platform's USB device. Fastboot is a USB @@ -1731,12 +1697,12 @@ The following options need to be configured: This enables support for booting images which use the Android image format header. - CONFIG_USB_FASTBOOT_BUF_ADDR + CONFIG_FASTBOOT_BUF_ADDR The fastboot protocol requires a large memory buffer for downloads. Define this to the starting RAM address to use for downloaded images. - CONFIG_USB_FASTBOOT_BUF_SIZE + CONFIG_FASTBOOT_BUF_SIZE The fastboot protocol requires a large memory buffer for downloads. This buffer should be as large as possible for a platform. Define this to the size available RAM for fastboot. @@ -1801,22 +1767,12 @@ CBFS (Coreboot Filesystem) support a default value of 65536 will be defined. - Keyboard Support: - CONFIG_ISA_KEYBOARD - - Define this to enable standard (PC-Style) keyboard - support - CONFIG_I8042_KBD Standard PC keyboard driver with US (is default) and GERMAN key layout (switch via environment 'keymap=de') support. Export function i8042_kbd_init, i8042_tstc and i8042_getc for cfb_console. Supports cursor blinking. - CONFIG_CROS_EC_KEYB - Enables a Chrome OS keyboard using the CROS_EC interface. - This uses CROS_EC to communicate with a second microcontroller - which provides key scans on request. - - Video support: CONFIG_VIDEO @@ -2380,16 +2336,20 @@ CBFS (Coreboot Filesystem) support - drivers/i2c/i2c_mxc.c - activate this driver with CONFIG_SYS_I2C_MXC + - enable bus 1 with CONFIG_SYS_I2C_MXC_I2C1 + - enable bus 2 with CONFIG_SYS_I2C_MXC_I2C2 + - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3 + - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4 - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE + - define speed for bus 4 with CONFIG_SYS_MXC_I2C4_SPEED + - define slave for bus 4 with CONFIG_SYS_MXC_I2C4_SLAVE If those defines are not set, default value is 100000 for speed, and 0 for slave. - - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3 - - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4 - drivers/i2c/rcar_i2c.c: - activate this driver with CONFIG_SYS_I2C_RCAR @@ -2461,6 +2421,15 @@ CBFS (Coreboot Filesystem) support - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3 - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3 - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3 + - activate dual channel with CONFIG_SYS_I2C_IHS_DUAL + - CONFIG_SYS_I2C_IHS_SPEED_0_1 speed channel 0_1 + - CONFIG_SYS_I2C_IHS_SLAVE_0_1 slave addr channel 0_1 + - CONFIG_SYS_I2C_IHS_SPEED_1_1 speed channel 1_1 + - CONFIG_SYS_I2C_IHS_SLAVE_1_1 slave addr channel 1_1 + - CONFIG_SYS_I2C_IHS_SPEED_2_1 speed channel 2_1 + - CONFIG_SYS_I2C_IHS_SLAVE_2_1 slave addr channel 2_1 + - CONFIG_SYS_I2C_IHS_SPEED_3_1 speed channel 3_1 + - CONFIG_SYS_I2C_IHS_SLAVE_3_1 slave addr channel 3_1 additional defines: @@ -3039,6 +3008,19 @@ CBFS (Coreboot Filesystem) support this is instead controlled by the value of /config/load-environment. +- Parallel Flash support: + CONFIG_SYS_NO_FLASH + + Traditionally U-boot was run on systems with parallel NOR + flash. This option is used to disable support for parallel NOR + flash. This option should be defined if the board does not have + parallel flash. + + If this option is not defined one of the generic flash drivers + (e.g. CONFIG_FLASH_CFI_DRIVER or CONFIG_ST_SMI) must be + selected or the board must provide an implementation of the + flash API (see include/flash.h). + - DataFlash Support: CONFIG_HAS_DATAFLASH @@ -3070,11 +3052,6 @@ CBFS (Coreboot Filesystem) support Define this option to include a destructive SPI flash test ('sf test'). - CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg - - Define this option to use the Bank addr/Extended addr - support on SPI flashes which has size > 16Mbytes. - CONFIG_SF_DUAL_FLASH Dual flash memories Define this option to use dual flash support where two flash @@ -3509,6 +3486,10 @@ FIT uImage format: without a fastmap. default: 0 + CONFIG_MTD_UBI_FM_DEBUG + Enable UBI fastmap debug + default: 0 + - UBIFS support CONFIG_CMD_UBIFS @@ -3579,6 +3560,9 @@ FIT uImage format: CONFIG_SYS_SPL_MALLOC_START Starting address of the malloc pool used in SPL. + When this option is set the full malloc is used in SPL and + it is set up by spl_init() and before that, the simple malloc() + can be used if CONFIG_SYS_MALLOC_F is defined. CONFIG_SYS_SPL_MALLOC_SIZE The size of the malloc pool used in SPL. @@ -4142,6 +4126,10 @@ Configuration Settings: list, simply add an entry for the same variable name to the ".flags" variable. + If CONFIG_REGEX is defined, the variable_name above is evaluated as a + regular expression. This allows multiple variables to define the same + flags without explicitly listing them for each variable. + - CONFIG_ENV_ACCESS_IGNORE_FORCE If defined, don't allow the -f switch to env set override variable access flags. @@ -5055,6 +5043,33 @@ within that device. normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the virtual address in NOR flash. +Freescale Layerscape Debug Server Support: +------------------------------------------- +The Freescale Layerscape Debug Server Support supports the loading of +"Debug Server firmware" and triggering SP boot-rom. +This firmware often needs to be loaded during U-Boot booting. + +- CONFIG_FSL_DEBUG_SERVER + Enable the Debug Server for Layerscape SoCs. + +- CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE + Define minimum DDR size required for debug server image + +- CONFIG_SYS_MEM_TOP_HIDE_MIN + Define minimum DDR size to be hided from top of the DDR memory + +Reproducible builds +------------------- + +In order to achieve reproducible builds, timestamps used in the U-Boot build +process have to be set to a fixed value. + +This is done using the SOURCE_DATE_EPOCH environment variable. +SOURCE_DATE_EPOCH is to be set on the build host's shell, not as a configuration +option for U-Boot or an environment variable in U-Boot. + +SOURCE_DATE_EPOCH should be set to a number of seconds since the epoch, in UTC. + Building the Software: ====================== @@ -5434,10 +5449,10 @@ List of environment variables (most likely not complete): unset, then it will be made silent if the U-Boot console is silent. - tftpsrcport - If this is set, the value is used for TFTP's + tftpsrcp - If this is set, the value is used for TFTP's UDP source port. - tftpdstport - If this is set, the value is used for TFTP's UDP + tftpdstp - If this is set, the value is used for TFTP's UDP destination port instead of the Well Know Port 69. tftpblocksize - Block size to use for TFTP transfers; if not set, @@ -5451,6 +5466,14 @@ List of environment variables (most likely not complete): faster in networks with high packet loss rates or with unreliable TFTP servers. + tftptimeoutcountmax - maximum count of TFTP timeouts (no + unit, minimum value = 0). Defines how many timeouts + can happen during a single file transfer before that + transfer is aborted. The default is 10, and 0 means + 'no timeouts allowed'. Increasing this value may help + downloads succeed with high packet loss rates, or with + unreliable TFTP servers or client hardware. + vlan - When set to a value < 4095 the traffic over Ethernet is encapsulated/received over 802.1q VLAN tagged frames. @@ -5540,6 +5563,10 @@ override any association in the static list. You can define CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the ".callbacks" environment variable in the default or embedded environment. +If CONFIG_REGEX is defined, the variable_name above is evaluated as a +regular expression. This allows multiple variables to be connected to +the same callback without explicitly listing them all out. + Command Line Parsing: =====================