X-Git-Url: http://git.ipfire.org/?a=blobdiff_plain;f=README;h=7abe2bc74bb01b7a8e5beff35021d74514d1441e;hb=7a01f3c6f401cf36d21121e3207ce8044bd18be4;hp=99af4c5bbf586f4d74c6d339f8eaadeb0fd53a7d;hpb=879704d8f7387b05272b79197a3c782d1499283b;p=people%2Fms%2Fu-boot.git

diff --git a/README b/README
index 99af4c5bbf..7abe2bc74b 100644
--- a/README
+++ b/README
@@ -830,14 +830,9 @@ The following options need to be configured:
 		CONFIG_CMD_CRC32	* crc32
 		CONFIG_CMD_DHCP		* DHCP support
 		CONFIG_CMD_DIAG		* Diagnostics
-		CONFIG_CMD_DTT		* Digital Therm and Thermostat
 		CONFIG_CMD_ECHO		  echo arguments
 		CONFIG_CMD_EDITENV	  edit env variable
-		CONFIG_CMD_EEPROM	* EEPROM read/write support
-		CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
 		CONFIG_CMD_ELF		* bootelf, bootvx
-		CONFIG_CMD_ENV_CALLBACK	* display details about env callbacks
-		CONFIG_CMD_ENV_FLAGS	* display details about env flags
 		CONFIG_CMD_ENV_EXISTS	* check existence of env variable
 		CONFIG_CMD_EXPORTENV	* export the environment
 		CONFIG_CMD_EXT2		* ext2 command support
@@ -846,15 +841,11 @@ The following options need to be configured:
 					  that work for multiple fs types
 		CONFIG_CMD_FS_UUID	* Look up a filesystem UUID
 		CONFIG_CMD_SAVEENV	  saveenv
-		CONFIG_CMD_FDC		* Floppy Disk Support
 		CONFIG_CMD_FAT		* FAT command support
 		CONFIG_CMD_FLASH	  flinfo, erase, protect
 		CONFIG_CMD_FPGA		  FPGA device initialization support
-		CONFIG_CMD_FUSE		* Device fuse support
-		CONFIG_CMD_GETTIME	* Get time since boot
 		CONFIG_CMD_GO		* the 'go' command (exec code)
 		CONFIG_CMD_GREPENV	* search environment
-		CONFIG_CMD_HASH		* calculate hash / digest
 		CONFIG_CMD_I2C		* I2C serial bus support
 		CONFIG_CMD_IDE		* IDE harddisk support
 		CONFIG_CMD_IMI		  iminfo
@@ -2324,17 +2315,6 @@ The following options need to be configured:
 		If defined, then this indicates the I2C bus number for the RTC.
 		If not defined, then U-Boot assumes that RTC is on I2C bus 0.
 
-		CONFIG_SYS_DTT_BUS_NUM
-
-		If defined, then this indicates the I2C bus number for the DTT.
-		If not defined, then U-Boot assumes that DTT is on I2C bus 0.
-
-		CONFIG_SYS_I2C_DTT_ADDR:
-
-		If defined, specifies the I2C address of the DTT device.
-		If not defined, then U-Boot uses predefined value for
-		specified DTT device.
-
 		CONFIG_SOFT_I2C_READ_REPEATED_START
 
 		defining this will force the i2c_read() function in
@@ -2401,19 +2381,6 @@ The following options need to be configured:
 
 		Specify the number of FPGA devices to support.
 
-		CONFIG_CMD_FPGA_LOADMK
-
-		Enable support for fpga loadmk command
-
-		CONFIG_CMD_FPGA_LOADP
-
-		Enable support for fpga loadp command - load partial bitstream
-
-		CONFIG_CMD_FPGA_LOADBP
-
-		Enable support for fpga loadbp command - load partial bitstream
-		(Xilinx only)
-
 		CONFIG_SYS_FPGA_PROG_FEEDBACK
 
 		Enable printing of hash marks during FPGA configuration.
@@ -2742,11 +2709,6 @@ The following options need to be configured:
 		but sometimes that is not allowed.
 
 - Hashing support:
-		CONFIG_CMD_HASH
-
-		This enables a generic 'hash' command which can produce
-		hashes / digests from a few algorithms (e.g. SHA1, SHA256).
-
 		CONFIG_HASH_VERIFY
 
 		Enable the hash verify command (hash -v). This adds to code
@@ -2755,11 +2717,6 @@ The following options need to be configured:
 		Note: There is also a sha1sum command, which should perhaps
 		be deprecated in favour of 'hash sha1'.
 
-- Freescale i.MX specific commands:
-		CONFIG_CMD_HDMIDETECT
-		This enables 'hdmidet' command which returns true if an
-		HDMI monitor is detected.  This command is i.MX 6 specific.
-
 - bootcount support:
 		CONFIG_BOOTCOUNT_LIMIT